iiyama ProLite T1633MC-B1 User manual

Category
TVs & monitors
Type
User manual

The iiyama ProLite T1633MC-B1 is a versatile monitor with a range of features to enhance your computing experience. With support for resolutions up to 1366 x 768, a high contrast ratio of 500:1, and a brightness of 300 cd/m2, it delivers crisp and vibrant visuals. It also incorporates a blue light reducer to minimize eye fatigue during prolonged use.

The iiyama ProLite T1633MC-B1 is a versatile monitor with a range of features to enhance your computing experience. With support for resolutions up to 1366 x 768, a high contrast ratio of 500:1, and a brightness of 300 cd/m2, it delivers crisp and vibrant visuals. It also incorporates a blue light reducer to minimize eye fatigue during prolonged use.

ENGLISH
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes
to read this comprehensive manual carefully
before installing and switching on the monitor.
Please keep this manual in a safe place for
your future reference.
USER MANUAL
ENGLISH
ENGLISH
Wereservetherighttochangespecicationswithoutnotice.
All trademarks used in this user manual are the property of their respective owners.
We recommend recycling of used product. Please contact your dealer or iiyama
service center. Recycle information is obtained via the Internet, using the address:
http://www.iiyama.com
YoucanaccesstheWebpageofdierentcountriesfromthere.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EU Directive 2014/30/EU “EMC
Directive”, 2014/35/EU “Low Voltage Directive” and 2011/65/EU “RoHS Directive”.
Warning
This is a class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands
Model No. : PLT1633M
ENGLISH
TABLE OF CONTENTS
FOR YOUR SAFETY ............................................................................ 1
SAFETY PRECAUTIONS................................................................1
SPECIAL NOTES ON LCD MONITORS .........................................3
CUSTOMER SERVICE ...................................................................3
CLEANING ......................................................................................3
BEFORE YOU OPERATE THE MONITOR ..........................................4
FEATURES......................................................................................4
CHECKING THE CONTENTS OF THE PACKAGE ........................4
SPECIAL NOTES ON TOUCH PANEL............................................5
WALL MOUNTING ..........................................................................5
BUILT-IN EQUIPMENT ....................................................................5
FITTING AND REMOVAL OF BASE ...............................................6
CONTROLS AND CONNECTORS..................................................7
CONNECTING YOUR MONITOR ...................................................8
ADJUSTING THE VIEWING ANGLE .............................................9
COMPUTER SETTING .................................................................10
OPERATING THE MONITOR .............................................................12
ADJUSTMENT MENU CONTENTS ..............................................13
SCREEN ADJUSTMENTS ............................................................19
POWER MANAGEMENT FEATURE .............................................22
TROUBLE SHOOTING ......................................................................23
RECYCLING INFORMATION .............................................................24
APPENDIX ........................................................................................25
SPECIFICATIONS : ProLite T1633MC-B1 ....................................25
DIMENSIONS ................................................................................ 26
COMPLIANT TIMING ....................................................................26
ENGLISH
FOR YOUR SAFETY 1
FOR YOUR SAFETY
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the
monitor and contact your dealer or iiyama service center immediately. Further use may be
dangerousandcancausereorelectricshock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
reorelectricshock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
anyobjectinsidemaycausere,electricshockordamage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Donotusewherewatermaybesplashedorspiltontothemonitorasitmaycausereorelectric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Besuretooperatethemonitoronlywiththespeciedpowersupply.Useofanincorrectvoltagewill
causemalfunctionandmaycausereorelectricshock.
CORRECT USE OF THE AC ADAPTER
Use only the AC Adapter provided by iiyama. Any deviation from this by using another type of
adaptermayresultindamagetotheaccessoryandthemonitorbyreorelectricshock.
DO NOT DISASSEMBLE THE AC ADAPTER
DisassemblingtheACAdaptermayexposeyoutothedangerofreorelectricshock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objectsonthecables.Ifdamaged,thecablesmaycausereorelectricshock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
SAFETY PRECAUTIONS
ENGLISH
2 FOR YOUR SAFETY
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or
smokyareasasitmaycausere,electricshockordamage.Youshouldalsoavoidareaswherethe
sun shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not
pull the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
re.Toallowadequateaircirculation,placethemonitoratleast10cm(or4inches)fromanywalls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the
cabinetwillbeblockedandthemonitormayoverheatifthestandisremoved.Thismaycausere
or damage. Operating the monitor on its back, side, upside down or on a carpet or any other soft
material may also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
Whenyoumovethemonitor,turnothePowerButton,unplugthemonitorandbesurethesignal
cableisdisconnected.Ifyoudonotdisconnectthem,itmaycausereorelectricshock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time, it is recommended that it is left unplugged to
avoid accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the AC adapter, the power cable or signal cable, always pull it by the plug. Never pull
onthecableitselfasthismaycausereorelectricshock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may
damage your computer.
REMARK FOR 24/7 USAGE
Thisproductisnotspecicallydesignedfor24/7usageinallenvironments.
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
Foroptimalviewingcomfort,themonitorshouldbejustbeloweyeleveland40-60cm(16-24inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
OTHERS
ENGLISH
FOR YOUR SAFETY 3
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE

When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture position to
the correct position.

You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.

Due to the nature of the LCD screen, an afterimage of the previous screen may remain
after switching the image, when the same image is displayed for hours. In this case, the
screenisrecoveredslowlybychangingtheimageorturningothePowerButtonfor
hours.
SPECIAL NOTES ON LCD MONITORS
WARNING
NOTE
CLEANING

If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.

To protect the Touch screen surface, do not scratch or rub the screen with a hard
object.

Never use any of the following strong solvents. These will damage the cabinet and
the Touch screen surface.
Abrasive cleaner Wax Acid or Alkaline solvent

Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
CABINET
Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
Then wipe the cabinet with a soft dry cloth.
TOUCH
SCREEN
Touch screen surface may be cleaned using a soft clean cloth moistened with mild
window glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.
NOTE

If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
CUSTOMER SERVICE
ENGLISH
4 BEFORE YOU OPERATE THE MONITOR
The following accessories are included in your package. Check to see if they are enclosed with
the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional
iiyamaoce.
* 1. TO USERS IN 120V AREA
The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are
using a power supply higher than this rating, then a power cable with a rating of
10A/250V must be used.
However, all guarantees and warranties are void for any problems or damage
caused by a power cable or AC adapter not supplied by iiyama.
2. Applicable AC Adapter
ACAdapterTypeName:ADPC1245,TPVELECTRONICS(FUJIAN)CO.,LTD.
3. An approved power cable greater or equal to H05VVF, 3G, 0.75mm
2
must be used.
AC Adapter*

Power Cable*
HDMI Cable

DisplayPort Cable

USB Cable
Stand-Base
Screws for Stand-Base
(4pcs)
Cable Cover
Screws for Cable Cover
(2pcs)
Safety Guide
Quick Start Guide

BEFORE YOU OPERATE THE MONITOR
CHECKING THE CONTENTS OF THE PACKAGE
CAUTION
FEATURES
Supports Resolutions up to 1366 × 768
High Contrast 500:1 (Typical)
Brightness 300cd/m
2
(Typical), 255cd/m
2
(with Touch Panel)
Blue Light Reducer
Digital Character Smoothing
Automatic Set-up

Plug & Play VESA DDC2B Compliant
Windows
®
7/8/8.1/10 Compliant
Power Management (VESA DPMS Compliant)
VESA Mounting Standard (100mm×100mm) Compliant
IP54 Standard Compliant (Only Front Face)
Keyhole for Security Lock
10 point Touch
Windows 7/8/8.1/10 touch environment
Basic touch operations can be performed under Windows 7/8/8.1/10.
However, please be informed that full touch functionality and normal operational performance are
not guaranteed.
ENGLISH
BEFORE YOU OPERATE THE MONITOR 5
When you use with the wall mounting, in
consideration of thickness of the mounting stage,
tighten the M4 Screw with washer which “L” length
is 8mm to fasten the monitor. Using the screw
longer than this may cause electric shock or
damage because it may contact with the electrical
parts inside the monitor.
WALL MOUNTING
Screw
Chassis
Mounting Stage
L
WARNING
Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch.
This could invalidate any remaining warranty.
Werecommendtouseaplasticstylus(tipR0.8orover)ornger.
SPECIAL NOTES ON TOUCH PANEL
This product is not designed for the purpose of being used in high temperature
environment.
If the product is placed in an external cabinet, you need to design cooling fans
and vents to keep the temperature low enough to fit in the product temperature
specication.
BUILT-IN EQUIPMENT
WARNING
ENGLISH
6 BEFORE YOU OPERATE THE MONITOR
FITTING AND REMOVAL OF BASE
CAUTION
Put the monitor on a stable surface. The monitor may cause injury or damage if it
falls or is dropped.
Do not give a strong impact to the monitor. It may cause damage.
Unplug the monitor before removal or installation to avoid an electric shock or a
damage.
<Removal>
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.
Laythemonitoratonatablewithfrontfacedown.
Remove the ‘thumb screws’ to remove the Stand-Base from the monitor.
<Installation>
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.
Laythemonitoratonatablewithfrontfacedown.
Hold the monitor and install the Stand-Base.
Use the ‘thumb screws’ provided to secure the Stand-Base to the monitor.
ThumbscrewsforStand-Basexing
Stand-Base
ENGLISH
BEFORE YOU OPERATE THE MONITOR 7
CONTROLS AND CONNECTORS
Cable Hole
USBDownstreamConnector(USB)
USBUpstreamConnector(USB)
Keyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
VGAConnector(VGA)
HDMIConnector(HDMI)
DisplayPortConnector(DP)
Connector for AC Adapter(:Directcurrent,DC-IN)
Power Indicator
Green: Normal operation
Orange: Power Management
Auto/InputSelectButton(AUTO)*
/EcoButton()*
+/BlueLightReducerButton(+)*
MenuButton(MENU)
PowerButton()
* You can skip the Menu items and directly display an option setting screen.
<Front>
<Back>
NOTE
NOTE
ENGLISH
8 BEFORE YOU OPERATE THE MONITOR
Ensurethatboththecomputerandthemonitorareswitchedo.
Connect the computer to the monitor with the signal cable.
Connect the computer to the monitor with the USB Cable.
Connect the HDMI cable to the monitor and the AV equipment when using an AV equipment
compliant to HDMI connection.
ConnecttheACAdapter to the monitor.ConnectthePowerCabletotheACAdapterrstand
then to the power source.
Turn on your monitor and computer.
The signal cables used for connecting the computer and monitor may vary with the
type of computer used. An incorrect connection may cause serious damage to both
the monitor and the computer. The cable supplied with the monitor is for a standard
connector. If a special cable is required please contact your local iiyama dealer or
regionaliiyamaoce.
For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyamaoceforasuitableadaptor.
MakesureyoutightenthengerscrewsateachendoftheSignalCable.
The Class I pluggable equipment Type A must be connected to protective earth.

The socket-outlet shall be installed near the equipment and shall be easily accessible.
CONNECTING YOUR MONITOR
[Example of Connection]
<Back>
Computer
USB Cable (Accessory)
Power Cable
(Accessory)
AC Adapter
(Accessory)
VGA Cable (Not Included)*
AV Equipment
HDMI Cable (Accessory)
DisplayPort Cable (Accessory)
NOTE
* VGA cable is not supplied with the monitor. If you use low quality VGA cable, it may cause a result
of electro-magnetic interference. Please contact the iiyama Support Centre in your country if you
wish to connect the monitor via the VGA input.
ENGLISH
BEFORE YOU OPERATE THE MONITOR 9
[ Fitting of Cable Cover ]
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay
themonitoratonatablewithfrontfacedown.
Step 1
Cable Hole
Step 2
Hand Screws
Cable Cover
As shown in Step 1, connect the
cables and put them through the
cable hole.
As shown in Step 2, place the cable
cover and fix it firmly with the hand
screws.
ADJUSTING THE VIEWING ANGLE
For optimal viewing it is recommended to look at the full
face of the monitor.
Hold the panel so that the monitor does not topple when
you change the monitor’s angle.
You are able to adjust the monitor’s angle up to 90
degrees upward, 5 degrees downward.
Do not touch the LCD screen when you change
the angle. It may cause damage or break the
LCD screen.
Careful attention is required not to pinch your
fingers or hands into the moving part of the
stand when you change the angle.
NOTE
90°
ENGLISH
10 BEFORE YOU OPERATE THE MONITOR
Signal Timing
Change to the desired signal timing listed on page 26: COMPLIANT TIMING.
Windows XP/Vista/7/8/8.1/10 Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs
on Windows XP/Vista/7/8/8.1/10 by connecting the monitor to DDC2B compliant computer with
the Signal Cable supplied.
For installation on Windows XP: The monitor Information File for iiyama monitors may be
necessary for your computer and obtained via the Internet, using the address:
http://www.iiyama.com

For additional information on how to download the driver for your touch screen monitor,
please access the internet site noted above.

Monitor Drivers are not required in most cases for Macintosh or Unix operating systems.
Forfurtherinformation,pleasecontactyourcomputerdealerrstforadvice.
COMPUTER SETTING
NOTE
Procedure for turning ON the Power Button
TurnONthemonitorrst,andthenthecomputer.
ENGLISH
BEFORE YOU OPERATE THE MONITOR 11

MULTI-TOUCH :
ThismonitorcomplieswithDDC2BofVESAstandard.(Plug&playcompliant)
The MULTI-TOUCH function runs on Windows7/8/8.1/10 by connecting the monitor to DDC2B
compliant computer with the USB cable supplied.

TOUCH support operation system :
OS Version
(Windows)
Windows
Win 10 Win8/8.1 Win7 XP
Supported touches Multi-touch Single-touch
Note
Windows inbox driver
(Noneedfortouchdriver)
Need for touch driver
OS Version
(LinuxDistribution)
Android
Linux7.0 6.0 5.0 - 5.1 4.0 - 4.4
Supported touches Multi-touch
Supported Kernel
version
4.4 3.18 3.0 - 3.14 3.0 - 4.4
Note
Driver supports multi-touch
Driver supports multi-
touch for most 3.0
above kernal
OS Version
(MacOS)
Mac OS
10.9(Mavericks) 10.10(Yosemite) 10.11(ElCapitan)
10.12(Sierra)
10.13(HighSierra)
Supported touches Single-touch
Note
Similar to Apple
Trackpad gesture:
2-ngergesture:
zoom in/out, swipe
4-ngergesture:
show desktop
Similar to Apple
Trackpad gesture:
2-ngergesture:
zoom in/out, swipe
4-ngergesture:
show desktop
Our service team
provides you with
the driver and the
operation guide.
Similar to Apple
Trackpad gesture:
2-ngergesture:
zoom in/out, swipe
4-ngergesture:
show desktop
Our service team
provides you with
the driver and the
operation guide.
Our service team
provides you with
the driver and the
operation guide.
ENGLISH
12 OPERATING THE MONITOR
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 26. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 19 for SCREEN ADJUSTMENTS.
Press the MENU Button to start the On Screen Display feature. There are additional
Menu items which can be switched by using the + / – Buttons.
Select the Menu item which contains the adjustment icon relating to the adjustment
you want to make. Press the MENU Button. Then, use the
+ / – Buttons to highlight
the desired adjustment icon.
Press the MENU Button again. Use the + / – Buttons to make the appropriate
adjustment or setting.
Press the AUTO Button to leave the menu, and the settings you just made would be
automatically saved.

When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the OSD Timeout has passed. Also, the
AUTO
Button can be used to return previous
menuandturnotheOn-ScreenDisplay.

Any changes are automatically saved in the memory when the On Screen Display
disappears.
TurningothepowershouldbeavoidedwhileusingtheMenu.

Adjustments for H. / V. Position, Clock and Phase are saved for each signal timing. Except for
these adjustments, all other adjustments have only one setting which applies to all signal timings.
NOTE
For example, to correct for vertical position, select Menu item of Image Setup and then press
the MENU Button. Then, select V. Position by using the + / – Buttons.
An adjustment page appears after you press the MENU Button. Then, use the + / – Buttons
to change the vertical position settings. The vertical position of the overall display should be
changing accordingly while you are doing this.
Press the
AUTO
Button lastly and all changes are saved in the memory.
Luminance
Contrast
Brightness
i-Style Color
50
100
Standard
Overdrive Off
Adv. Contrast
Off
OSD
Exit
Move
Select
AUTO
MENU
Image Setup
Clock
Phase
Aspect Ratio
H. Position
50
86
Full
50
OSD
Exit
Move
Select
AUTO
MENU
V. Position
50
ENGLISH
OPERATING THE MONITOR 13
ADJUSTMENT MENU CONTENTS
Adjustment Item Problem / Option Button to Press
Luminance
Too dark
Too bright
Brightness *
1
Contrast
Too dull
Too intense
*
1
Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright. Brightness adjustment is disabled when Eco is activated.
*
2
i-Style Color cannot be adjusted and selected while Blue Light Reducer is active.
*
3
When Overdrive is activated, some level of image retention will be caused.
Luminance
Contrast
Brightness
i-Style Color
50
100
Standard
Overdrive Off
Adv. Contrast
Off
OSD
Exit
Move
Select
AUTO
MENU
i-Style Color *
2
Standard
For general windows environment and monitor
default setting.
Text
For text editing and viewing in a word processing
environment.
Internet For internet environment.
Game
For PC game environment.
Movie
For movie and video environment.
Sports
For sport environment.
Adv. Contrast
Increased Contrast Ratio
On
O
Typical Contrast Ratio
Adv. Contrast adjusts brightness according to the image, and improve the contrast ratio
during movie playing.
Contrast, Brightness, Color Temp., Eco, i-Style Color and Blue Light Reducer cannot be
adjusted and selected while Adv. Contrast is active.
NOTE
Overdrive *
3
O/-2/-1/0/+1/+2
It will improve the gray level response time of the
LCD panel.
A higher level results in a faster response time.
+
+
+
ENGLISH
14 OPERATING THE MONITOR
Adjustment Item Problem / Option Button to Press
Image Setup
Phase*
1,2
Clock*
1,2
Too left
Too right
Too low
Too high
H. Position*
2
V. Position*
2
Too narrow
Too wide
Tocorrectickeringtextorlines
Image Setup
Clock
Phase
Aspect Ratio
H. Position
50
86
Full
V. Position
50
50
Exit
Move
Select
AUTO
MENU
*
1
See page 19 for SCREEN ADJUSTMENTS.
*
2
Only for Analog Input.
Expanded displayFull
Aspect Expanded display by Aspect ratio
Aspect Ratio
+
+
+
+
ENGLISH
OPERATING THE MONITOR 15
Adjustment Item Problem / Option Button to Press
Color Temp. *
Green
Red
Blue
Color Temp.
Color Temp.
Red
Green
Warm
43
Blue
44
50
OSD
Exit
Move
Select
AUTO
MENU
Color Temp.
Normal
Warm
Cool
sRGB
NOTE

sRGBisan international standard whichdenes andunies thedierence of color
appearance between equipment.
You can not adjust the Contrast, Brightness, i-Style Color and Eco during sRGB
mode because those settings are locked.
Too weak
Too strong
User
* Color Temp. cannot be adjusted and selected while Blue Light Reducer is active.
+
ENGLISH
16 OPERATING THE MONITOR
Language
English
Deutsch
English
German
Français French
Japanese
Timeout
You can set the OSD display duration time
between 5 and 100 seconds.
Adjustment Item Problem / Option Button to Press
OSD Setup
OSD
OSD Setup
H. Position 95
V. Position 5
Timeout
Language
10
English
Exit
Move
Select
AUTO
MENU
Touch Wake Up Off
OSD
Polski
Polish
Русский Russian
Nederlands
Dutch
Portuguese
Italiano Italian
Español Spanish
Português
Čeština Czech
H. Position
V. Position
OSD is too left
OSD is too right
OSD is too low
OSD is too high
+
+
+
Touch and USB hub are still functional during the
display stand by.
On
O
Touch Wake Up isturnedo.
Touch Wake Up
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

iiyama ProLite T1633MC-B1 User manual

Category
TVs & monitors
Type
User manual

The iiyama ProLite T1633MC-B1 is a versatile monitor with a range of features to enhance your computing experience. With support for resolutions up to 1366 x 768, a high contrast ratio of 500:1, and a brightness of 300 cd/m2, it delivers crisp and vibrant visuals. It also incorporates a blue light reducer to minimize eye fatigue during prolonged use.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI