Miller MG000000G is a single mounting bracket designed to provide support for Miller® SubArc welding equipment or other welding equipment. It can be mounted to a fixed or movable slide, and is intended to provide support for the Miller Flux Hopper and wire drive system. The bracket is made of durable materials and is easy to install. With its sturdy construction and versatile design, the Miller MG000000G is a valuable addition to any welding setup.
Miller MG000000G is a single mounting bracket designed to provide support for Miller® SubArc welding equipment or other welding equipment. It can be mounted to a fixed or movable slide, and is intended to provide support for the Miller Flux Hopper and wire drive system. The bracket is made of durable materials and is easy to install. With its sturdy construction and versatile design, the Miller MG000000G is a valuable addition to any welding setup.
OWNER’S MANUAL OM-274405B
2016−04
For Single Mounting Bracket (301134)
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in
the text.
DANGER ! - Indique une situation dangereuse qui, si elle
n’est pas évitée, entraînera la mort ou des blessures graves.
Les éventuels risques sont représentés par les symboles
joints ou expliqués dans le texte.
Fsafe1 2013-10
Beware of electric shock from wiring. Disconnect input pow-
er before installing this kit. Reinstall all panels and covers.
Attention aux décharges électriques au contact des câbles.
Couper l’alimentation électrique avant d’installer ce kit. Ré-
installer tous les panneaux et couvercles.
Fsafe7 2013-10
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury. The possible hazards are
shown in the adjoining symbols or explained in the text.
Indique une situation dangereuse qui, si elle n’est pas évitée,
entraînera la mort ou des blessures graves. Les éventuels
risques sont représentés par les symboles joints ou exp-
liqués dans le texte.
Fsafe2 2013-10
Wear safety glasses with side shields.
Porter des lunettes de sécurité avec écrans latéraux.
Fsafe8 2013-10
NOTICE
Indicates statements not related to personal injury.
Signale des consignes non associées aux dommages cor-
porels.
Indicates special instructions.
Fournit des instructions spéciales.
Fsafe3 2013-10
Have only trained and qualified persons install, operate, or
service this unit. Read the safety information at the begin-
ning of these instructions and in each section. Call your dis-
tributor if you do not understand the directions. For WELD-
ING SAFETY and EMF information, read owner’s manual(s).
Ne confiez l’installation, l’exploitation ou l’entretien de cet
appareil qu’à des personnes compétentes et qualifiées. Lire
les directives de sécurité au début de ces instructions et
dans chaque section. Appeler votre distributeur si vous
ne comprenez pas les directives. Lire le(s) manuel(s)
d’utilisateur pour des renseignements sur la SÉCURITÉ
DE SOUDAGE et les champs électromagnétiques.
Fsafe15 2013-10
CALIFORNIA PROPOSITION 65 WARNINGS
Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some
cases, cancer. (California Health & Safety Code Section 25249.5 et seq.) This product contains chemicals, including lead, known to the state of Cali-
fornia to cause cancer, birth defects, or other reproductive harm. Wash hands after use.
Les équipements de soudage et de coupage produisent des fumées et des gaz qui contiennent des produits chimiques dont l’État de Californie recon-
naît qu’ils provoquent des malformations congénitales et, dans certains cas, des cancers. (Code de santé et de sécurité de Californie, chapitre
25249.5 et suivants) Ce produit contient des produits chimiques, notamment du plomb, dont l’État de Californie reconnaît qu’ils provoquent des
cancers, des malformations congénitales ou d’autres problèmes de procréation. Se laver les mains après utilisation.
Fsafe4 2013-10
2. Description
The single mounting bracket is designed to provide support for Miller®SubArc welding equipment or other welding equipment. The mounting bracket is
intended to provide support for the Miller Flux Hopper and wire drive system. This unit can either be mounted to a fixed or movable slide.
Contact the manufacturer of the fixed or movable slide to ensure it is capable of supporting the weight of the single mounting bracket
and attached equipment.
3. Specifications
Product Type Overall Dimensions Weight
Single Mounting Bracket 9.38 in. X 9.87 in. X 10.63 in.
(238 mm x 250 mm x 270 mm)
14 lbs
(6.4 kg)
4. Tools Needed
8 mm
7/16, 9/16 in.
OM-274405 Page 2
5. Dimensions
10.625 in.
(269 mm)
9.865 in.
(250 mm)
Top View
9.375 in.
(238 mm)
∅ .413 in. X 4 Thru
〈∅ 10.5 mm X 4 Thru)
Side view
Front View
4.33 in.
(110 mm)
5.750 in.
(146 mm)
1.969 in.
(50 mm)
273 921-A
6.000 in.
(152 mm)
OM-274405 Page 3
6. Threaded Hole Layout
M10 x 1.5-6H 4 Places
1.966 in.
(50 mm)
4.311 in.
(110 mm)
. The single mounting bracket is provided with M10 x 25 socket head cap hardware for at-
taching the bracket to a fixed arm or movable slide. If desired, 3/8 - 16 x 1.00 in. hardware
may be used. In this case, the threaded hole should be adjusted accordingly.
274 404-A
Notes
OM-274405 Page 4
7. Installation
! Turn Off all electrical equip-
ment before working on unit.
1 Single Mounting Bracket
2 M10 Flat Washers
3 M10 Lock Washers
4 M10-1.5 x 25 SOC HD Cap
Screws
5 Fixed Arm
6 Manual Cross Slide
OPTION 1 − To mount the single
mounting bracket to a fixed arm, align
the four holes on the bracket with the
threaded holes on the fixed arm. Se-
cure bracket by tightening the four
M10 x 25 screws and hardware with a
8mm Allen wrench. Torque hardware
to 30 ± 2 ft-lb (40 ± 3 N⋅M).
OPTION 2 − To mount the single
mounting bracket to a cross slide,
align the four holes on the bracket with
the M10 threaded holes on the cross
slide. Secure bracket by tightening the
four M10 x 25 screws and hardware
with a 8mm Allen wrench. Torque
hardware to 30 ± 2 ft-lb (40 ± 3 N⋅M).
. When mounting the bracket to a
cross slide, be sure that the single
mounting bracket is mounted to a
vertical slide to allow for clear-
ance.
1
2
3
4
5
6
Option 1
Option 2
274 433-A
OM-274405 Page 5
8. Mounting A Flux Hopper
! Turn Off all electrical equipment
before working on unit.
. Secure single mounting bracket to
fixed arm, or cross slide (see Sec
-
tion 7) before mounting flux hopper
.
1 Flux Hopper
2 Insulator
3 Mounting Plate (Flux Hopper)
4 1/4 in. Insulating Shoulder Washer
5 1/4 in. Flat Washer
6 1/4 − 20 x .75 in. Screws
7 Single Mounting Bracket
8 1/4 − 20 x 1.00 in. Screws (Sup-
plied w/Single Mounting Bracket)
Before installing single mounting brack-
et, remove hardware, and discard flux
hopper mounting plate and the 1/4 - 20
x .75 in. screws. Retain insulator, and
other hardware. Place existing insulator
between flux hopper and single mount-
ing bracket. Align holes, and secure flux
hopper to single mounting bracket with
supplied 1/4 - 20 x 1.00 in. screws and
existing hardware. Torque screws to
7.5 ± 1 ft-lb (10 ± 1.5 N⋅M).
1
2
3
4
5
6
1
2
7
4
5
8
Threaded Holes
274 435-A
OM-274405 Page 6
9. Mounting A Wire Drive
! Turn Off all electrical equip-
ment before working on unit.
. Secure single mounting bracket to
fixed arm, or cross slide (see Sec
-
tion 7) before mounting wire drive
motor.
1 Wire Drive Motor
2 3/8 - 16 Nuts
3 Single Mounting Bracket
4 Insulator
5 3/8 in. Insulating Spacer
6 3/8 in Insulating Washer
7 3/8 in. Flat Washer
8 3/8 in. Lock Washer
9 3/8 -16 Screws
Remove and discard the four 3/8 -16
nuts from the wire drive motor. Retain
the insulator, and other hardware
.
Place existing insulator between wire
drive motor and single mounting
bracket. Align holes and secure wire
drive motor to single mounting bracke
t
with existing 3/8 - 16 screws, wash-
ers, insulating washers, and insulating
spacers. Torque screws to 23 ± 2 ft-lb
(31 ± 3 N⋅M).
274 606-A
1
2
5
4
Threaded
Holes
1
3
6
7
8
9
OM-274405 Page 7
Notes
OM-274405 Page 8
Notes
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Miller MG000000G Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Miller MG000000G is a single mounting bracket designed to provide support for Miller® SubArc welding equipment or other welding equipment. It can be mounted to a fixed or movable slide, and is intended to provide support for the Miller Flux Hopper and wire drive system. The bracket is made of durable materials and is easy to install. With its sturdy construction and versatile design, the Miller MG000000G is a valuable addition to any welding setup.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Miller MF000000G Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
HobartWelders RCCS-RJ Owner's manual
-
Miller Electric GPS-1500A Owner's manual
-
ESAB A6S Arc Master/ A6S G Master/ A6S Compact 500 User manual
-
-
-
-
ESAB A6 Mastertrac Tandem User manual