S4709 © 05/23 PAGE 2 OF 3
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Removal of Stock System
1. Apply penetrating lubricant liberally to all exhaust fasteners, hangers, and
rubber insulators.
2. Disconnect the exhaust valve actuator electrical connection on the passenger-
side. There is a small tab to press down to unlock the connector. Unhook the
wiring harness support from the chassis (circled) to allow extra length for the
installation.
Refer to Figure 1.
3. Remove the front pipe nuts after the catalytic converter and save the nuts for
the installation.
4. With the rear of the exhaust system supported, remove the factory insulators
from the vehicle. Retain the insulators for the installation.
5. Remove the exhaust system from the vehicle. Ensure the factory gasket
remains on the catalytic converter for installation.
6. Remove the valve actuator from the factory system. The factory flange nuts,
drive spring and actuator will be reused for the installation.
Installation of MBRP Performance Exhaust
1. Using the factory nuts removed in Step 3, loosely attach the Front Pipe onto
the catalytic converter.
Refer to Figure 2.
2. Using a 3.0” Clamp, loosely install the Mid-Pipe onto the Front Pipe.
Refer to Figure 3.
3. Using a 3.0” Clamp, loosely install the Y-Pipe onto the Mid-Pipe. Reinstall
the factory rubber insulator.
Refer to Figure 4.
4. Install the Spring Hub and valve actuator onto the Passenger-Side Tail Pipe
using the factory flange nuts, M5x22 Hex Bolts, and Flat Washers. Ensure the
valve is open and the drive spring is in the Spring Hub correctly.
Refer to Figure 5.
5. Using a 3.0” Clamp, loosely install the Passenger-Side Tail Pipe onto the Y-
Pipe. Reinstall the factory rubber insulator.
Refer to Figure 6.
S4709 © 05/23 PAGE 3 OF 3
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
6. Using a 3.0” Clamp, loosely install the Driver-Side Tail Pipe onto the Y-
Pipe. Reinstall the factory rubber insulator.
Refer to Figure 7.
7. Install the Tips and adjust to you liking.
Refer to Figures 8 and 9.
8. Re-connect the exhaust valve actuator electrical connection. Secure the
wiring to the chassis exhaust hanger using the Cable tie, ensuring the wiring will
not contact the Passenger-Side Tail Pipe but be loose enough to move with the
exhaust.
Refer to Figure 10.
9. Carefully align the system, centering the Tips with the factory fascia
openings. Align the edge of each band clamp with the edge of the joint it is
connecting. Tighten all hardware and clamps, starting at the front and working
rearward to secure the system. Check along the full length of the exhaust system
to ensure there is adequate clearance for fuel lines, vent lines, brake lines, frame,
bodywork, suspension and any wiring, etc. If there is any interference detected,
relocate or adjust to provide adequate clearance. Ensure all clamp connections
are secure and components are unable to rotate or slide. Band clamps require
approximately 45 lb-ft (60 N-m) of torque. Verify clearances, system security
and band clamp torque after 30-60 miles (50-100 km) of driving.
Congratulations! You are ready to begin experiencing the improved power,
sound and driving experience of your MBRP Performance Exhaust.
We know you will enjoy your purchase!
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
MBRP S5227BLK Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
aFe Power 48-48021 Installation guide
-
Chevrolet TrailBlazer User manual
-
Chrysler Vehicle User manual
-
Pontiac 1968 User manual
-
Kawasaki NINJA ZX-12R User manual
-
-
-
aFe Power 48-06209 Installation guide
-
aFe Power 48-46209 Installation guide
-
