Astria Fireplaces DRT4040/45-OLD Instruction Sheet

Astria Fireplaces
Brand
Astria Fireplaces
Model
DRT4040/45-OLD
Category
Fireplaces
Type
Instruction Sheet
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1
2nd step
•Dissemble the screw and the
bracket that hold the sparker
and the thermocouple in
place.
1st step
•Disassemble the screw
from the bas of the pilot.
1st step
1st step
•Disassemble the screw
from the bas of the pilot.
REPLACEMENT THERMOCOUPLE AND IGNITER ELECTRODE KITS FOR FIREPLACES WITH ECOFLOW SYSTEMS
[FOR USE WITH VARIOUS IHP DIRECT-VENT GAS FIREPLACES WITH THE ECOFLOW SYSTEM]
REQUIRED TOOLS AND SUPPLIES
T20 Torx Key Driver
TURN OFF THE GAS SUPPLY TO THE APPLIANCE. DISCONNECT
ELECTRICAL POWER SUPPLY.
READ ALL THE STEPS BEFORE STARTING THE INSTALLATION
NOTE: THE FIREPLACE MUST BE OFF AND COLD BEFORE BEGINNING.
ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE INSTAL-
LATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE
APPLY TO THESE INSTRUCTIONS.
GENERAL INFORMATION
The replacement thermocouple and igniter electrode kits covered
by this document are designed to provide the qualified installer
the ability to replace the thermocouple and/or igniter electrode on
existing IHP fireplaces with EcoFlow systems.
INSTALLATION INSTRUCTIONS
Step 1. Using a Torx T20 key, remove the screw from the base of the pilot.
See Figures 1 and 2.
ECOFLOW REPLACEMENT THERMOCOUPLE
AND IGNITER ELECTRODE KITS
P/N 900841-00
Rev. NC, 02/2017
HEARTH PRODUCTS
KITS AND ACCESSORIES
Figure 1 - Screw on Base of Pilot
Figure 2 - Using T20 Torx Key, Remove Screw
Step 2. Remove the bracket that holds the igniter electrode and the ther-
mocouple in place. See Figure 3.
Figure 3 - Remove Bracket
Screw
Bracket
T20 Torx Key
Screw
Thermocouple
Igniter Electrode
Cat. No. Description
F3268 Replacement Thermocouple Kit
F3267 Replacement Igniter Electrode Kit
Screw
KIT COMPONENTS
1 ea. Thermocouple or Igniter Electrode
1 ea. Instruction Sheet
2
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
4th step
•When the thermocouple
and the sparker are in
place, make sure that the
bracket fits in the grooves
of the thermocouples and
sparker.
3rd step
•Slide the thermocouple
and the sparker out.
•Change the
thermocouple and/or
the sparker
Printed in U.S.A. © 2017 Innovative Hearth Products
P/N 900841-00 Rev. NC 02/2017
IHP reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices and also to discontinue colors, styles and products. Consult your local
distributor for fireplace code information.
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
Step 3. Remove thermocouple and/or igniter electrode. See Figure 4.
Step 4. Install the new thermocouple and/or igniter electrode. Ensure
that the bracket fits in the grooves of the thermocouple and/or
igniter electrode. See Figure 5.
Step 5. Tighten the screw until the bracket is secure.
Figure 5 - Install Thermocouple and/or Igniter Electrode
Figure 4 - Remove Thermocouple and/or Igniter Electrode
Thermocouple
Igniter Electrode
4th step
•When the thermocouple
and the sparker are in
place, make sure that the
bracket fits in the grooves
of the thermocouples and
sparker.
Thermocouple Groove
Igniter Electrode Groove
  • Page 1 1
  • Page 2 2

Astria Fireplaces DRT4040/45-OLD Instruction Sheet

Astria Fireplaces
Brand
Astria Fireplaces
Model
DRT4040/45-OLD
Category
Fireplaces
Type
Instruction Sheet
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents