CAME MS9502, 818XG-0021 Installation guide

Type
Installation guide
1/4
MS9502
1/4
The sensor can be installed
on the surface by using the
surface mount box.
Place a silicone seal to
increase water resistance.
Use the screwdriver to
remove the front face.
Avoid moving objects in
front of the sensor
Do not place the sensor
behind metallic plates.
Do not force when turning
the adjustment screw.
Do not place the sensor
in the opening range of
the door.
The sensor can be placed
behind tiles, wood, plaster,
plastic and glass.
Detection range adjustment
Front face
after power on
during activation
of output relay
LED
Antenna
Fixing frame
Output mode:
Toggle or Pulse
Terminal block
INSTALLATION TIPS
DESCRIPTION
MICROWAVE CONTACTLESS SWITCH
USER’S GUIDE
SL N
IICO ESL N
IICO E
2/4
4
6
5
123
10cm
50cm
78 9
T
P
10cm
50cm
POWER
COM
NO
NC
50mm
70mm
“click”
“click”
SILICONE
SILICONE
Make a hole and insert the
recessed box into the opening.
Pull the wires through the box.
If you do not use the fixation
brackets, unscrew them.
Fix the screws of the recessed
housing in the oval holes.
Insert the housing into the
recessed box and tighten the
screws firmly.
Make sure the output mode is set to PULSE-mode (P) for standard door applications.
Adjust the detection range according to the application.
Note that the detection range depends on the trajectory, size and
nature/material of the detected object.
Connect the wires to the
terminal block. After
connection, the LED flashes.
In order to increase water
resistance, place a silicone seal
on the front cover.
Clips the front cover on the
fixation braket.
Make sure the LED-signal is
visible and test the good
functioning of the sensor by
moving the hand towards the
sensor.
TOGGLE MODE
PULSE MODE
: Recommended for
switch applications. In toggle mode, a
detection activates the relay and a second
detection deactivates it again. In door
applications, the door stays open after the
first activation.
: Recommended for
automatic door applications. In pulse
mode, a detection activates the relay for a
short period of time (depending on the
duration of the movement in front of the
sensor).
RELAY ON
RELAY OFF
RELAY ON
RELAY OFF
INSTALLATION
min. 1s
DOOR OPENS
DOOR OPENS
AND CLOSES DOOR OPENS
AND CLOSES
DOOR CLOSES
LED
LED SIGNAL
LED flashes LED switches ON LED is OFF
Microwave motion sensor
24.150 GHz
2
<< 5mW/cm
+/- 10 to 50 cm if movement towards sensor at 90° (adjustable)*
Motion (bidirectional)
Min. 5Hz or +/- 3cm/s, Max. 200Hz or +/- 1.2m/s
12 - 24V AC +/- 10%
12 - 24V DC +30% / - 10%
50 - 60 Hz
< 1.2W
Relay with switch-over contact (free of potential)
48V AC - 60V DC
1A (resistive)
30W (DC) / 48VA (AC)
0.5s (in PULSE mode)
-20°C - +55°C
R&TTE: 1999/5/EC; EMC: 2004/108/EEC
ABS / PC
White
2
Stranded cable up to 16 AWG - 1.5mm
Technology:
Radiated frequency:
Radiated power density:
Detection range (hand):
Detection mode:
Speed of target to create detection:
Supply voltage:
Mains frequency:
Power consumption:
Output:
Max. voltage:
Max. current:
Max. switching power:
Output hold time:
Temperature range:
Norm conformity:
Material:
Colour:
Recommended wiring cable:
SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
Specifications are subject to changes without prior notice
* The adjustment of the detection field below 10cm is possible, but the detection capability of the sensor can not be guaranteed!
3/4
Bad or no power supply
Wrong connection
Wrong connection
Wrong connection
Wrong output mode Switch the output mode
to PULSE mode.
Detection range is too small.
The environment influences
the good functioning of the sensor.
Adjust the detection range.
Remove any moving objects close
to the sensor.
Check wiring and relay connection.
Check wiring and relay connection.
Check wiring and relay connection.
Check power supply.
The door does
not open even when
moving hand
towards the sensor.
The door remains
permanently open.
The door remains open
after
detection/activation.
If LED switches on or flashes,
power connection is OK.
Remove any metal plates
in front of the sensor.
OFF
ON
ON
ON
OFF
OFF
OFF
All data checked with the maximum care. However, no liability is accepted for any error or omission.
The declaration de conformity and other technical documentation are available on our website www.came.it
BUY-TO-SELL PRODUCT
MS9 1 PM8 0 8_502_ 19 0_ver 2. _08/200EN
42.0852 - V2 / 08.08
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

CAME MS9502, 818XG-0021 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI