2. FLEXCO
  3. Hinge Pin Retaining Collars

FLEXCO Hinge Pin Retaining Collars Operating instructions

  • Hello! I've reviewed the Installation Instructions for the Hinge Pin Retaining Collar X2296. This document provides a 5-step guide on how to properly install the retaining collars to secure hinge pins using set screws and maintaining a 3/8" gap. I'm ready to answer any questions you have about these instructions and the installation process.
  • What is the first step in the installation process?
    How much gap is needed between the collar and the splice end loop?
    How many screws are used to secure the retaining collar?
For Reorder: X2296
Installation:
1. Insert and center hinge pin in splice.
2. Place first Retaining Collar over one end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
3. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely.
4. Place second Retaining Collar over opposite end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
5. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely
INSTALLATION INSTRUCTIONS
HINGE PIN RETAINING COLLARS
For Reorder: X2296
Installation:
1. Insert and center hinge pin in splice.
2. Place first Retaining Collar over one end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
3. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely.
4. Place second Retaining Collar over opposite end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
5. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely
INSTALLATION INSTRUCTIONS
HINGE PIN RETAINING COLLARS
For Reorder: X2296
Installation:
1. Insert and center hinge pin in splice.
2. Place first Retaining Collar over one end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
3. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely.
4. Place second Retaining Collar over opposite end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
5. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely
INSTALLATION INSTRUCTIONS
HINGE PIN RETAINING COLLARS
For Reorder: X2296
Installation:
1. Insert and center hinge pin in splice.
2. Place first Retaining Collar over one end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
3. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely.
4. Place second Retaining Collar over opposite end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
5. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely
INSTALLATION INSTRUCTIONS
HINGE PIN RETAINING COLLARS
For Reorder: X2296
Installation:
1. Insert and center hinge pin in splice.
2. Place first Retaining Collar over one end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
3. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely.
4. Place second Retaining Collar over opposite end of hinge pin. (Leave approximately 3/8” gap between the collar and the splice end loop)
5. Loosely set all three screws evenly around the hinge pin so all knurled points are in contact with the hinge pin. -
Then finish tightening all three screws securely
INSTALLATION INSTRUCTIONS
HINGE PIN RETAINING COLLARS
/