Julian Bowen WIL001 Assembly Instructions

Before you start....

Please carefully unpack and lay out all of the component parts to ensure nothing

is missing and to check each component for any obvious damage.

Should you identify any concerns at this stage please contact the retailer from

whom this product was purchased. Please quote your order number, details of

your issue, the product code, and the batch number from the cartons which will

help to resolve your issue as quickly as possible.

Version Number - 1.0 Product Code - WIL001

Tools RequiredPeople Required to Assemble

FABRIC 135CM 4 DRAWER BED

1hr

Approximate Assembly Time

ASSEMBLY

INSTRUCTIONS

1500

1300

2070

No Extra

Tools Required

No Extra

Tools Required

No Extra

Tools Required

2

8

M8x30mm

+Spring Washer

+Flat Washer

12x 16x

Already inserted into

Head & Foot Ends

M5x70mm

3x

30x60

4x

M4x20mm

1x

Please check all hardware matches the list below. Should

you notice any are missing please contact your retailer.

We strongly advise that you do not use Power Tools, such as

drills or electric screwdrivers during the assembly as this

may cause irreparable damage and will invalidate your

warranty.

3

A B C

E F G

I 4x J

M4x20mm

64x MN

32x

M5x50mm

8x

D

H

O

48x L

M5

1x

M8x45mm

+Flat Washer

8x

M4x30mm

20x

M5x50mm

48x

M8x30mm

+Spring Washer

+Flat Washer

2x K

PARTS

4

Please ensure you carefully check all the pieces, should you have any

concerns please contact the retailer before assembly commences.

Please have your order number, details of the issue, the product code,

and the batch number from the cartons as this will help us to resolve

your issue much faster.

face out

(2x)

01

02

03

04

05

06

07 (32x)

08

10

12

11

11 13

13

14

15

09

16

(2x)

18

19

11

11 13

13

20

17

16

ASSEMBLY ADVICE

Please take the time to carefully read through these instructions

before you commence.

Keep these instructions for future reference.

We advise that the product is assembled in the room it is intended for.

We advise that you keep the hardware in a bowl during assembly to

avoid losing anything.

We strongly recommend that you keep children away from the work

area.

Small component parts could choke a child if swallowed.

We recommend you use a sheet or blanket to protect both floor and

product through the assembly stages.

Never push or pull the product as this could cause both personal injury

or irreparable damage to product or floor.

We have tried to make this piece of furniture easy to assemble if the

instructions are followed carefully.

In the unlikely event that you have problems with assembling the

product or have missing or damaged parts, please contact your

retailer and we will assist them in rectifying the problem as quickly as

possible.

Remember we strongly urge you DO NOT use power tools such as drill

or electric screwdrivers as this could cause irreparable damage to

your product and will invalidate your warranty.

5

Please note that

the Bolt (A) x 12

are prefixed into

parts 1 & 2

1

2

3

E

6

01

03

02

03

04 04

05

B

A

01

02 06

06

01

02

H

06

I

H

06

I

face out

4

6

7

02

5

03

02

09

03

E

F

08

ARROWS ON LABELS

POINT TO EACH OTHER

J

08

09

02

01

04

G

E

face out

K

face out

D

PUSH

C

07

C

07

7

8

C

DD

07 07

8

FOLLOW LINE ON BACK OF

DRAWER FACE PANEL

III III

Positions For Castors

(Large) x2

Part 13 x 2

9

Important:

Make sure when you fit the nuts

that the hole is in the correct

alignment.

Drawer Assembly

L

10

IV V

15

10

11

14

11

12

13

16

10

L

O

MN

(Small) x2

face out

FOLLOW LINE ON BACK OF

DRAWER FACE PANEL

11

13

10

Important:

Make sure when you fit the nuts

that the hole is in the correct

alignment.

Drawer Assembly L

12 Positions For Castors

III III

IV V

13

16 17

17

18

11

20

11

19

L

Part 13 x 2

O

MN

GENERAL CARE & MAINTENANCE

We advise that when cleaning the product that a damp cloth is used.

Avoid the use of all household cleaners and abrasive.

Never push or drag the furniture.

Never attempt to move the furniture when fully loaded.

We advise that periodically all fixing are re-tightened.

11

Julian Bowen WIL001 Assembly Instructions

Julian Bowen WIL001 Assembly Instructions

Related papers

Other documents