Consumption metering module with M bus interface
PIC-M-XP_V2.1.1_PI_2022-07_EN 1
Subject to technical changes
PIC-M-XP
1 PIC-M-XP
Consumption metering module with M bus interface
1.1 Front view
Fig. 1: Front view
1.2 Features
• Consumption recording of electrical energy, heat quantity, water and gas for 6 M bus meters
• Synchronisation with the quarter-hour signal of the energy service provider (ESP)
• Correct tariff metering for 2 tariffs by the connected meters
• Internal storage of power demand for evaluation of power peaks
• Saves extensive consumption values for statistical analysis
• Graphical representation of power consumption and querying of consumption meters and statis-
tics in FRIGODATA XP
• Overload, short circuit and data collision detection
• Plug-in screw terminals
• Direct connection of a CAN-USB to the service socket
• Connection to the Wurm system via communication bus (CAN bus) and FRIGODATA XP
Consumption metering module with M bus interface
2 PIC-M-XP_V2.1.1_PI_2022-07_EN
Subject to technical changes
PIC-M-XP
1.3 Safety instructions
Writing conventions
WARNUNG • Avoid the described hazard: otherwise, electric voltage represents a danger that could lead to
fatal or serious bodily injury.
VORSICHT • Avoid the described hazard: otherwise minor or medium bodily injury or damage to property will
result.
For your safety
For safe operation and to avoid personal injury and equipment damage through operator error, always
read these instructions, become familiar with the device, and follow all safety instructions on the prod-
uct and in this document, as well as the safety guidelines of Wurm GmbH & Co. KG Elektronische
Systeme. Keep these instructions ready to hand for quick reference and pass them on with the device
if the product is sold.
Wurm GmbH & Co. KG Elektronische Systeme accepts no liability in the case of improper use or use
for purposes other than the intended purpose.
WARNUNG DANGER TO LIFE FROM ELECTRIC SHOCK AND/OR FIRE!
• Switch off the power to the entire plant when carrying out installation, wiring or disassembly work!
Otherwise, mains voltage and/or external voltage may still be present, even if the control voltage
is switched off! Always remove both power plugs (L and N).
• The wiring of the device must be carried out only by qualified electricians!
• Use the correct tools for any work!
• Check the entire wiring after connection!
• Observe the maximum loads for all connections!
• Never expose the device to moisture, for example due to condensation or cleaning agents.
• Stop operating the device if it is faulty or damaged and its safe operation is compromised!
• Do not open the device.
• Do not repair the device yourself! If the device requires repairs, send it in with an exact descrip-
tion of the fault!
VORSICHT ELECTROMAGNETIC INTERFERENCE MAY CAUSE FAULTS!
• Always use shielded data cables and place them far away from power lines.
Target group This manual is intended for "service technician" personnel.
Intended use The device records the consumption of electrical energy, heat, water
and gas by meters connected to an M bus interface.
Wurm Infocenter paperless info
Consumption metering module with M bus interface
PIC-M-XP_V2.1.1_PI_2022-07_EN 3
Subject to technical changes
PIC-M-XP
Version and validity of the documentation
Any versions not listed are special solutions for individual projects and are not described in detail in this document.
This document will automatically cease to be valid if a new technical description is issued.
Manufacturer: Wurm GmbH & Co. KG Elektronische Systeme, Morsbachtalstraße 30, D-42857 Remscheid
You can find more information on our website at www.wurm.de.
1.4 Circuit diagram
Fig. 2: Circuit diagram
Version Date
V2.1.1 2022-07 Documentation status
L
N
S2S1
RxD
TxD
LEDs
21
54321
GND
CAN-L
CAN-H
n.c.
38 37 36 35 34 33 32 3139 38 37 36 35 34 33 32 3139
TxD
RxD
DCD
DTR
31
33
35
37
32
34
36
38
39
L
N
MOD-LAN-XP
GatewayGatewayGatewayМежсетевой шлюз
Odlazno-dolazna
stanica
GatewayGateway
Bramka
18 19
17161514131211
PIC-6-XP
-+
1
2
3
4
5
6
Temperatur 1
Temperatur 2
Istwert
Imp. / Einheit
Stromwandler
Einheit
kW
m³ / h
Alarmpriorität
Adresse
Menü
l / h
Messkanal
PIC-6-XP
-+
1
2
3
4
5
6
Temperatur 1
Temperatur 2
Istwert
Imp. / Einheit
Stromwandler
Einheit
kW
m³ / h
Alarmpriorität
Adresse
Menü
l / h
Messkanal
PIC-6-XP
-+
1
2
3
4
5
6
Temperatur 1
Temperatur 2
Istwert
Imp. / Einheit
Stromwandler
Einheit
kW
m³ / h
Alarmpriorität
Adresse
Menü
l / h
Messkanal
PIC-6-XP
-+
1
2
3
4
5
6
Temperatur 1
Temperatur 2
Istwert
Imp. / Einheit
Stromwandler
Einheit
kW
m³ / h
Alarmpriorität
Adresse
Menü
l / h
Messkanal
n.c.
GND
n.c.
RxD
TxD
1
Alarmpriorität
1
1
1
2
33
2
Adresse
Istwert
Einheit
1
2
3
PIC-M-XP
-+
1
2
3
4
5
6
+--++
-
0V
+U
n.c.
LEDs
M bus data
communication
Synchronisation
input
Price-input
Service socket
M bus
Connection Function
Bridging switch Switch position right
Minus connection 13 is connected to 0V connection 11.
Switch position left
Minus connection 13 is not connected to 0V connection 11.
Switch position right
Minus connection 15 is connected to 0V connection 11.
Switch position left
Minus connection 15 is not connected to 0V connection 11.
Consumption metering module with M bus interface
4 PIC-M-XP_V2.1.1_PI_2022-07_EN
Subject to technical changes
PIC-M-XP
1.5 Installing the device
This device is designed for top-hat rail installation. The housing has standard DIN 43880 dimensions
and is also suitable for operation in fuse boxes and distribution cabinets.
The device can be positioned immediately adjacent to another device without gaps.
WARNUNG DANGER TO LIFE FROM ELECTRIC SHOCK AND/OR FIRE!
• Switch off the power to the entire plant before installing. Otherwise, mains voltage and/or exter-
nal voltage may still be present, even if the control voltage is switched off. Always remove both
power plugs (L and N).
The entire plant must be free of voltage.
1. (A) Place the device with the leading edge at an acute angle to the top-hat rail.
2. (B) Push the device downwards onto the top-hat rail.
The device snaps into place with the fastening safety catch (a) on the top-hat rail.
You can now connect the device.
Fig. 3: Top-hat rail installation
1.6 Technical data
Power supply 230V~, +10%/-15%, max. 10VA
Display 2 x LED, CAN bus data traffic (CAN Tx, CAN Rx)
2 x LED, M bus data traffic (Tx, Rx)
Communication CAN bus 3-wire CAN bus interface with integrated power supply, gal-
vanically isolated, service socket
CAN bus baud rate 20kBd, 50kBd, 125kBd
Meter communication M bus interface: up to 6 M bus slaves connectable
M bus baud rate 300Bd, 2400Bd, 9600Bd
Digital inputs 1 x pulse input, floating for synchronisation of measurement
periods
1 x switching input, potential-free for tariff changeover
Temperature sensor 2 x TRK277/7 PLUS or TRK277/G2
Internal clock time Detection of system clock time from the gateway
Power reserve in case of power failure
Central unit Single-chip microcomputer, data memory
Monitoring system Self-monitoring of data memory and microcomputer
Dimensions (W x H x D) 106 x 90 x 58mm (DIN 43880)
Fastening Top-hat rail TH 35-15 or TH 35-7.5 (DIN EN 60715)
Ambient temperature Operation: 0...+55°C, storage: -25...+70°C
Weight About 466g
Conformities - 2014/30/EU (EMC Directive)
- 2014/35/EU (Low Voltage Directive)
EAC conformity - TR CU 004/2011
- TR CU 020/2011
RoHS II
Valid from Version 2.1.1
A
B
7
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WURM DIN-BL Product information
-
WURM PIC-M-XP Product information
-
WURM CRC-BL Product information
-
WURM PIC-XP Product information
-
WURM CRC-BL Product information
-
WURM PIC-6-XP Product information
-
WURM RF-W Product information
-
WURM PIC-6-XP Product information
-
WURM DIN-BL Product information
-
WURM DIN-BL Product information
