urban ambiance UQL3402 Installation guide

Brand
urban ambiance
Model
UQL3402
Type
Installation guide
Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
(2)MediumBaseDecorativeFilament60Wbulb(provided),Maximum100W,Alternatebulb(2)23WCFLMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
ToolsRequired:
LightSource:
EstimatedAssembly Time:
Preparation:
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
E
B
Lock
Screw
x4
Inner
Backplate
x1
STEP 1 Install Inner Backplate and Fixture Body-
A. Pass the supply wires through Inner Backplate (A). Attach Inner
Backplate (A) to Outlet Box with the head of Green Ground Screw
facing you. Secure it with Outlet Box Screws (not included). Tighten
until snug
B. Refer to Step 2 for wiring connections.
C. Attach Fixture Body (D) over Inner Backplate (A) and secure with
Lock Screws (B). Tighten until snug with screwdrivers.
.
A
Shade
x2
D
Fixture
Body
x1
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
STEP 3 - Install Shades and
Bulbs
A. Place Shade (E) over the
Socket, secure by threading
Socket Collar (F) onto the
Socket. Hand tighten until
sung.
B. This fixture uses Medium
Base Decorative Filament
60W bulb (C), Maximum
100W. Insert bulb and screw
snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
Figure 3
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires between Inner Backplate (A) and Fixture Body (D).
C
Edison
Bulb
x2 F
Socket
Collar
x2
A
Figure 1
Outlet Box
Outlet Box
Screw
D
B
E
F
C
Socket
Installation Instructions: UQL3402
www.urbanambiance.com
2of2
UQL3402
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
FINISH: BLACK BRONZE
(2)Medium Base
Decorative
Filament 60W
bulbs (provided),
Maximum 100W.
6.75”Dia.
5”
8.25”
8.75”
17.5”
21
www.urbanambiance.com
  • Page 1 1
  • Page 2 2

urban ambiance UQL3402 Installation guide

Brand
urban ambiance
Model
UQL3402
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers