APC AP9554 User manual

APC Power

Distribution Unit

AP9554

Installation Manual

Installationshandbuch

Manual de instalación

Manuel d'installation

Page is loading ...

®

APC Power

Distribution Unit

AP9554

Installation Manual

Page is loading ...

3

Contents

BeforeyouBegin .............................5

Installation ..................................6

Mounting options 6

Attach the mounting brackets 6

Attach the unit to the enclosure 7

Operation...................................8

Specifications.................................9

Warranty Information 10

Limited warranty 10

Warranty limitations 10

Life-SupportPolicy............................11

General policy 11

Examples of life-support devices 11

ObtainingService ............................12

DeclarationofConformity......................13

APCWorldwideCustomerSupport................14

Page is loading ...

5

Before you Begin

Safety &

grounding

information

Read the following information before installing or operating

your

APC

Power Distribution Unit (

PDU

):

•This

PDU

is intended for indoor use only.

• Do not install this

PDU

where excessive moisture or

heat is present.

• Never install any wiring, equipment, or

PDU

during a

lightning storm.

•Plugthis

PDU

into a three-wire, grounded power outlet

only. The power outlet must be connected to appropriate

branch circuit/mains protection (fuse or circuit breaker).

Connection to any other type of power outlet may result

in a shock hazard.

• Use only the supplied brackets for mounting.

• Do not use an additional extension cord or adapter with

the primary power cord.

• Do not work alone under hazardous conditions.

• Check that the power cord, plug, and socket are in good

condition.

• To reduce the risk of electric shock when you cannot

verify grounding, disconnect the

PDU

from the power

outlet before installing or connecting equipment.

Reconnect to the power outlet only after you have made

all connections.

• Pluggable equipment includes a protective earth

connector which carries the leakage current from the

load devices (computer equipment). Do not exceed a

total leakage current of 3.5 mA.

• Do not handle any kind of metallic connector before the

power has been removed.

• Use one hand, whenever possible, to connect or

disconnect signal cables to avoid a possible shock from

touching two surfaces with different grounds

• This unit contains no user serviceable parts. Repairs are

performed only by factory-trained service personnel.

• Always install the equipment as shown in the User

Manual.

6

Installation

Mounting

options

Your PDU comes with two different mounting brackets, the

“Z” bracket (figures 1 and 2) and the “L” bracket (figure 3).

The PDU is equipped with a hole pattern that easily

accommodates your installation needs. Study the figures on

this page and page 7 for mounting options.

Attach the

mounting

brackets

1. Decide where in the enclosure you are installing the PDU

and choose a bracket.

2. Decide which direction you would like the outlets to be

facing and orient the brackets appropriately.

3. Attach the rack-mount brackets to the unit, using four flat-

head Phillips screws (provided) for each bracket.

Continued on next page

7

Installation

continued

Attach the unit

to the

enclosure

1. Install caged nuts (provided with your enclosure) in your

chosen location. Make sure that the caged nuts line up with

the mounting brackets that you have attached to the unit.

2. Align the mounting holes of the brackets with the installed

caged nuts. Insert screws and tighten.

8

Operation

Overview

!

Inlet

IEC 320 C20 inlet (16A @ 240V; 20A @ 120V)

used with detached power cord (supplied)

.

"

Ground

stud

6-32

ground stud that can be used to ground the

unit to the enclosure

#

Circuit

Breaker

When the button is extended, the circuit breaker

is tripped, the

PDU

is overloaded, and at least

one piece of equipment needs to be unplugged.

The circuit breaker is rated to trip at the same

overload as most home and office utility service

branch protectors (

20A

).

$

Outlets

Fourteen IEC 320 C13

outlets

(

10A @ 240V; 15A @ 120V

)

9

Specifications

Product

specifications

.

Item Specification

Power

Input voltage range: 120–240 V

Maximum current draw:

208 V @ 12.8A (UL, CUL)

120 V @ 16A (UL, CUL)

240 V @ 16A (VDE)

Physical

Size (H × W × D):

24.4 × 1.75 × 2.25 in

(62.0 × 4.45 × 5.72 cm)

Weight:

4.44 lb

(2.01 kg)

Shipping weight:

6.02 lb

(2.73 kg)

Environmental

Elevation (above MSL):

Operating

Storage

0 to 10,000 ft (0 to 3000 m)

0 to 50,000 ft (0 to 15 000 m)

Temperature:

Operating

Storage

32 to 113° F(0to45° C)

–13 to 149° F(–25 to 65° C)

Relative humidity:

Operating

Storage

0 to 95%, non-condensing

Approvals/Standards

UL, CUL, VDE

10

Warranty Information

Limited

warranty

American Power Conversion (

APC

) warrants the Power

Distribution Unit to be free from defects in materials and

workmanship for a period of two years from the date of

purchase. Its obligation under this warranty is limited to

repairing or replacing, at its own sole option, any such defective

products. This warranty does not apply to equipment that has

been damaged by accident, negligence, or misapplication or has

been altered or modified in any way. This warranty applies only

to the original purchaser.

Warranty

limitations

Except as provided herein, American Power Conversion makes

no warranties, express or implied, including warranties of

merchantability and fitness for a particular purpose.

Some jurisdictions do not permit limitation or exclusion of

implied warranties; therefore, the aforesaid limitation(s) or

exclusion(s) may not apply to the purchaser.

Except as provided above, in no event will

APC

be liable for

direct, indirect, special, incidental, or consequential damages

arising out of the use of this product, even if advised of the

possibility of such damage.

Specifically,

APC

is not liable for any costs, such as lost profits

or revenue, loss of equipment, loss of use of equipment, loss of

software, loss of data, costs of substitutes, claims by third

parties, or otherwise. This warranty gives you specific legal

rights and you may also have other rights, which vary from state

to state.

11

Life-Support Policy

General policy

As a general policy, American Power Conversion (

APC

)does

not recommend the use of any of its products in life-support

applications where failure or malfunction of the

APC

product

can be reasonably expected to cause failure of the life-support

device or to significantly affect its safety or effectiveness.

APC

does not recommend the use of any of its products in direct

patient care. APC will not knowingly sell its products for use

in such applications unless it receives in writing assurances

satisfactory to APC that (a) the risks of injury or damage have

been minimized, (b) the customer assumes all such risks, and

(c) the liability of American Power Conversion is adequately

protected under the circumstances.

Examples of

life-support

devices

The term life-support device includes but is not limited to:

neonatal oxygen analyzers, nerve stimulators (whether used for

anesthesia, pain relief, or other purposes), autotransfusion

devices, blood pumps, defibrillators, arrhythmia detectors and

alarms, pacemakers, hemodialysis systems, peritoneal dialysis

systems, neonatal ventilator incubators, ventilators for both

adults and infants, anesthesia ventilators, infusion pumps and

any other devices designated as “critical” by the

U.S

.

FDA

.

Hospital-grade wiring and leakage current protection may be

ordered as options on many

APC UPS

systems.

APC

does not

claim that units with these modifications are certified or listed

as Hospital Grade by

APC

or any other organization. Therefore

these units do not meet the requirements for use in direct

patient care.

12

Obtaining Service

If problems

persist

If you are experiencing problems with your PDU that are not

covered in this manual, or if problems with your PDU persist:

1. Note the serial number and date of purchase of the

Power Distribution Unit. Contact Customer Support at a

phone number or address on the back cover of this

manual.

2. Be prepared to provide a description of the problem. A

technician will help solve the problem over the phone, if

possible, or will give you a return material authorization

(RMA) number.

3. If the Power Distribution Unit is under warranty, repair

or replacement is free of charge. If the warranty has

expired, there will be a charge for repair or replacement.

4. Pack the Power Distribution Unit carefully to avoid

damage in transit. Damage sustained in transit is not

covered under the warranty. Enclose a letter in the

package with your name, address, RMA number, a copy

of the sales receipt, daytime phone number, and check

(if applicable).

5. Mark the RMA number clearly on the outside of the

shipping carton. The factory will not accept any

materials without this marking.

6. Return the Power Distribution Unit by insured, prepaid

carrier to the address provided by the Customer Support

technician.

13

Declaration of Conformity

Application of

Council Directives

72/23/EEC

Standards to Which

Conformity is

Declared

DIN EN60950 (VDE 0805): 1997-11 + A11: 1998-08

EN60950: 1992 + A1:1993 + A2:1993 + A3:1995 +

A4: 1997+A11:1997

IEC 950: 1991 + A1:1992 + A2:1993 + A3:1995 +

A4:1996 + A11:1997

Manufacturers

Name and Address

American Power Conversion

132 Fairgrounds Road

West Kingston, Rhode Island 02892

USA

or

American Power Conversion (A.P.C.) b.v.

Ballybritt Business Park

Galway, Ireland

Importers Name and

Address

American Power Conversion (A.P.C.) b.v.

Ballybritt Business Park

Galway, Ireland

Type of Equipment

Power Distribution Unit

Model Numbers

AP9554

Serial Numbers

WK0001000000 and above

Year of Manufacture

2001 onward

We, the undersigned, hereby declare that the equipment specified above

conforms to the above directives

.

St. Louis, MO, Jan

. 23,

2001

Ted E cke rt

Regulatory Compliance

Engineer

Galway, Ireland Jan. 23, 2001

Ray Ballard

General Manager,

Galway

Place

Date

APC Worldwide Customer Support

Customer support for this or any other APC product is available at no charge in any of

the following ways:

• Visit the APC Web site to find answers to frequently asked questions

(FAQs), to access documents in the APC Knowledge Base, and to submit

customer support requests.

– http://www.apcc.com (Corporate Headquarters)

Connect by links to APC Web pages for specific countries and regions,

each of which provides customer support information.

– http://www.apcc.com/support

/

Submit customer support requests.

• Contact an APC Customer Support center by telephone or e-mail.

– Regional centers:

.

– Local, country-specific centers: go to http://www.apcc.com/support/

contact for contact information.

• Contact the APC representative or other distributor from whom you pur-

chased your APC product for information on how to obtain local customer

support.

APC Headquarters

(U.S. and Canada)

(1) (800) 800-4272 (toll free)

Latin America

(1) (401) 789-5735 (United States)

[email protected]

Europe, Middle East,

Africa

(353) (91) 702020 (Ireland)

[email protected]

Japan

(03) 5434-2021

[email protected]

15

®

APC Kaltgeräte-

Mehrfachsteckdose

AP9554

Installationshandbuch

Page is loading ...

29

Anwendung der

Ratsdirektiven

72/23/EEC

Zugrundeliegende

Normen für die

Konformitätserklärung

DIN EN60950 (VDE 0805): 1997-11 +

A11: 1998-08

EN60950: 1992 + A1:1993 + A2:1993 +

A3:1995 + A4: 1997+A11:1997

IEC 950: 1991 + A1:1992 + A2:1993 +

A3:1995 + A4:1996 + A11:1997

Name und Adresse des

Herstellers

American Power Conversion

132 Fairgrounds Road

West Kingston, Rhode Island 02892

USA

-oder-

American Power Conversion (A.P.C.) b.v.

Ballybritt Business Park

Galway, Ireland

Name und Adresse des

Importeurs

American Power Conversion (A.P.C.) b.v.

Ballybritt Business Park

Galway, Ireland

Gerätetyp

UPS-Zubehör

Modell-Nummern

AP9554

Die unterzeichnenden Parteien erklären hiermit, dass die oben

beschriebenen Geräte den obigen Vorschriften entsprechen.

St.Louis,MO

Ort

23. Januar 2001

Datum Ted Eckert

Ingenieur fürdie

Regulierungsbehörde

Galway, Ireland

Ort

23. Januar 2001

Datum Ray Ballard

General Manager, Galway

Konformitätserklärung

Page is loading ...

45

Aplicacióndelas

Council Directives

72/23/EEC

Estándares con los

que se declara la

conformidad

DIN EN60950 (VDE 0805): 1997-11 +

A11: 1998-08

EN60950: 1992 + A1:1993 + A2:1993 +

A3:1995 + A4: 1997+A11:1997

IEC 950: 1991 + A1:1992 + A2:1993 +

A3:1995 + A4:1996 + A11:1997

Nombre y dirección

del fabricante

American Power Conversion

132 Fairgrounds Road

West Kingston, Rhode Island 02892

EE.UU.

-o-

American Power Conversion (A.P.C.) b.v.

Ballybritt Business Park

Galway, Irlanda

Nombre y dirección

del importador

American Power Conversion (A.P.C.) b.v.

Ballybritt Business Park

Galway, Irlanda

Tipo de equipo

Equipo accesorio de UPS

Números de modelo

AP9554

Nosotros, los abajo firmantes, declaramos que el equipo

anteriormente especificado se ajusta a las directivas antes citadas.

St.Louis,MO

Lugar

23 de enero de

2001

Fecha

Ted Eckert

Ingeniero encargado del

cumplimiento de las regulaciones

Galway, Irlanda

Lugar

23 de enero de

2001

Fecha

Ray Ballard

Administrador general, Galway

Declaracióndeconformidad

Page is loading ...

61

Application des

directives du Conseil

72/23/EEC

Normes auxquelles la

conformité est

déclarée

DIN EN60950 (VDE 0805): 1997-11 +

A11: 1998-08

EN60950: 1992 + A1:1993 + A2:1993 +

A3:1995 + A4: 1997+A11:1997

IEC 950: 1991 + A1:1992 + A2:1993 +

A3:1995 + A4:1996 + A11:1997

Nom et adresse du

fabricant

American Power Conversion

132 Fairgrounds Road

West Kingston, Rhode Island 02892

Etats-Unis

ou

American Power Conversion (A.P.C.) b.v.

Ballybritt Business Park

Galway, Irlande

Nom et adresse de

l’importateur

American Power Conversion (A.P.C.) b.v.

Ballybritt Business Park

Galway, Irlande

Type d’équipement

Equipement accessoire d’un onduleur

Numéros de modèle

AP9554

Nous, soussignés, déclarons par la présente que l’équipement

spécifié ci-dessus est conforme aux normes susdites.

St. Louis, Etats-Unis

Lieu

23 janvier 2001

Date Ted Eckert

Ingénieur Conformité aux Normes

Galway, Irlande

Lieu

23 janvier 2001

Date Ray Ballard

Directeur Général, Galway

Déclaration de conformité

Page is loading ...

Reproduction in whole or in part without

permission is prohibited. APC and NetShelter are

registered trademarks of American Power

Conversion Corporation. All other trademarks,

product names, and corporate names are the

property of their respective owners and are used

for informational purposes only.

American Power Conversion. Reservados todos

los derechos. Se prohíbe la reproducción total o

parcial sin permiso. APC y NetShelter son

marcas registradas de American Power

Conversion Corporation. Todas las demás marcas

comerciales, nombres de productos y de

empresas pertenecen a sus respectivos

propietarios y se utilizan sólo con fines

informativos.

reproduction en tout ou partie sans permission est

interdite. APC et NetShelter sont des marques

déposées de AmericanPower Conversion

Corporation. Tous les autres noms de produits et

desociétés, les marquescommerciales sont la

propriété de leurs détenteurs respectifs et sont

utilisés uniquement à titre d’information.

American Power Conversion. Alle Rechte vorbe-

halten. Vollständige oder teilweise Reproduktion

ohne Genehmigung ist untersagt. APC und Net-

Shelter sind eingetragene Warenzeichen der

American Power Conversion Corporation. Alle

anderen Warenzeichen, Produktbezeichnungen

und Unternehmensbenennungen sind Eigentum

der jeweiligen Eigentümer und werden nur zu

Informationszwecken genutzt.

990-6058 01/2001

APC AP9554 User manual

APC AP9554 User manual

in other languages

Related papers

Other documents