Black & Decker NPP2018 User manual

1

KE

Y

I

NFORMATION

Y

OU

S

HOULD

KNOW

:

•

Ch

a

rg

e

b

a

tte

ry fo

r 9

h

o

u

rs b

e

fo

re

fi

rst u

se

.

•

DO NOT OVER-TENSION CHAIN. Re

fe

r to

"ADJUSTING

CHAIN TENSION"

fo

r p

ro

p

e

r me

th

o

d

o

f te

n

si

o

n

in

g

ch

a

i

n

.

• Re

tig

h

te

n

ch

a

i

n

fre

q

u

e

n

tly d

u

ri

n

g

fi

rst two

h

o

u

rs o

f u

se

.

Catalog Number NPP2018

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

Cordless Pole Saw

INSTRUCTION MANUAL

Thank you for choosing Black & Decker! Go to

www.BlackandDecker.com/NewOwner

to register your new product.

PLEASE READ BEFORE RETURNING

THIS PRODUCT FOR ANY REASON:

If you have a question or experience a problem

with your Black & Decker purchase, go to

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

If you can’t find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak

with an agent. Please have the catalog number available when you call.

for instant answers 24 hours a day.

2

IMPORTANT SAFETY RULES

WARNING: Read and understand all instructions. Failure to

follow all instructions listed below may result in electric shock, fire

and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Before Operating Pole Saw

• For safe operation, read and understand all instructions before

using the Pole Saw. Follow all safety instructions. Failure to follow

all safety instructions listed below, can result in serious personal

injury.

• Watch what you are doing. Use common sense. Do not operate

Pole Saw when you are tired.

• Use Pole Saw for cutting wood only. Do not use Pole Saw for

purpose not intended. Do not use for cutting non-wood items.

• Only well-instructed adults should operate Pole Saw. Never allow

children to operate.

• Do not allow children or untrained individuals to use this unit.

• Wear the following safety gear when operating Pole Saw:

- heavy-duty gloves

- steel-toed safety footwear with non-skid soles

- safety glasses, goggles or face screen that are marked to

comply with ANSI Z87

- safety hard hat

- ear mufflers or ear plug

- face or dust mask (if working in dusty areas)

• Wear heavy long pants and boots. Do not wear loose fitting

clothing, short pants, jewelry of any kind, or go barefoot.

• Secure long hair so it is above shoulder level to prevent

entanglement in any moving parts.

• Before cutting, always provide the following:

- clear work area

- secure footing

- planned retreat path from falling limbs

• Inspect tree before trimming. Make allowance for branches to fall

freely to the ground.

• Do not use your Pole Saw to fell saplings.

While Operating Pole Saw

• Stay alert. Use common sense while operating the unit.

• Keep work area clean. Cluttered areas invite injuries.

• Keep children, animals and bystanders at least 50 ft. (15 m) away

from Pole Saw. Only Pole Saw user should be in work area.

• Do not use the Pole Saw to cut down trees.

• Grip Pole Saw securely - one hand on the pole, the other on the

handle.

• Keep finger off trigger until ready to make cut.

• Before starting Pole Saw, make sure chain is not touching anything.

• Keep all parts of body away from chain when Pole Saw is running.

• Do not force Pole Saw while cutting. Apply light pressure. It will do

the job better and safer at the rate for which it was intended.

• Carry Pole Saw from one place to another

- with battery removed

- by holding pole at balance point

- with guide bar and chain to rear and with scabbard attached

• Do not cut small brush and saplings with the Pole Saw. Slender

matter may catch in the chain and be whipped toward you. This

could also pull you off balance.

• Do not operate in poor lighting.

• Keep firm footing and balance. Do not overreach. Overreaching

can result in loss of balance or exposure to hot surfaces.

• Keep all parts of your body away from any moving part.

• Do not, under any circumstance, use any attachment or accessory

on this product, which was not provided with the product, or

identified as appropriate for use with this product in this Instruction

Manual.

Do not operate Pole Saw:

- while under the influence of alcohol, medication, or drugs

- in rain or in damp or wet areas

- where highly flammable liquids or gases are present

3

- if Pole Saw is damaged, adjusted wrong, or not fully and

securely assembled

- if trigger does not turn Pole Saw on and off. Chain must stop

moving when you release trigger. Have faulty switch replaced by

authorized service center. See “Service Information”.

- while in a hurry

- while in tree or on a ladder

- while on aerial booms, buckets or platforms

- during high wind or storming weather

General Safety Rules

WARNING: Shock Hazard. To protect yourself from electrocution,

do not operate within 50 feet (15 m) of overhead electrical lines.

Failure to do this could result in severe personal injury.

• To protect yourself from falling branches do not stand directly under

the branch or limb being cut. This unit should not be held at an

angle over 60 degrees from ground level.

• Keep the handles dry, clean, and free of oil.

• Before you start the unit, make sure the chain is not contacting any

object.

• Make sure the cutting chain has stopped before setting the unit

down.

Service

• Tool service must be performed only by qualified repair

personnel. Service or maintenance performed by unqualified

personnel could result in a risk of injury. See “Service Information”.

• When servicing a tool, use only identical replacement parts.

Follow instructions in the Maintenance section of this manual.

Use of unauthorized parts or failure to follow Maintenance

Instructions may create a risk of electric shock or injury.

Guard Against Kickback

WARNING: KICKBACK may occur when the nose or tip of the

guide bar touches an object, or when the wood closes in and pinches

the saw chain in the cut. Tip contact in some cases may cause a

lightning fast reverse reaction, kicking the guide bar up and back

towards the operator. Pinching the saw chain along the top of the

guide bar may push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of the saw

which could result in serious injury to user.

The following precautions should be followed to minimize

kickback:

• Grip Pole Saw firmly. Hold the saw firmly with both hands when the

unit is running. Use a firm grip with thumbs and fingers encircling

the saw handle and pole.

• Do not over reach.

• Keep proper footing and balance at all times.

• Don't let the nose of the guide bar contact a log, branch, ground or

other obstruction.

• Do not extend Pole Saw handle above shoulder height.

• Use devices such as low kickback chain, chain braking system and

special guide bars that reduce the risks associated with kickback.

• Only use replacement bars and chains specified by the

manufacturer or the equivalent.

• Never let the moving chain contact any object at the tip of the guide

bar.

• Keep the working area free from obstructions such as other trees,

branches, rocks, fences, stumps, etc. Eliminate or avoid any

obstruction that your saw chain could hit while you are cutting

through a particular log or branch.

• Keep your saw chain sharp and properly tensioned. A loose or dull

chain can increase the chance of kickback. Check tension at

regular intervals with the motor stopped and battery removed.

• Begin and continue cutting only with the chain moving at full speed.

If the chain is moving at a slower speed, there is a greater chance

for kickback to occur.

• Cut one branch at a time.

• Use extreme caution when re-entering a previous cut. Engage

spiked bumpers into wood and allow chain to reach full speed

before proceeding with cut.

• Do not attempt plunge cuts or bore cuts.

• Watch for shifting branches or other forces that could close a cut

and pinch or fall into chain.

4

Kickback Safety Features

Warning: The following features are included on your Pole Saw

to help reduce the hazard of kickback; however such features will

not totally eliminate this dangerous reaction. As a chain saw user do

not rely only on safety devices. You must follow all safety

precautions, instructions, and maintenance in this manual to help

avoid kickback and other forces which can result in serious injury.

• Reduced-Kickback Guide Bar, designed with a small radius tip

which reduces the size of the kickback danger zone on bar tip. A

reduced- kickback guide bar is one which has been demonstrated

to significantly reduce the number and seriousness of kickbacks

when tested in accordance with safety requirements for electric

chain saws.

• Low-Kickback Chain, designed with a contoured depth gauge and

guard link which deflect kickback force and allow wood to gradually

ride into the cutter. A low-kickback chain is a chain which has met

kickback performance requirements of ANSI B175.1 when tested

on the representative sample of chain saws.

Specific Safety Rules

• Hold tool by insulated gripping surfaces when performing an

operation where the cutting tool may contact hidden wiring.

Contact with a "live" wire will make exposed metal parts of the tool

"live" and shock the operator.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber. (CCA)

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed

to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse

dust, which may cause serious and permanent respiratory or

other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away

from face and body.

SAVE THESE INSTRUCTIONS

The label on your tool may include the following symbols.

V................volts A ....................amperes

Hz..............hertz W ..................watts

min ............minutes ..................alternating current

..........direct current

n

o ..................no load speed

..............

Class II Construction

....................earthing terminal

............safety alert symbol .../min ............revolutions or

per minute

SAFETY WARNINGS AND

INSTRUCTIONS

CHARGING

1. This manual contains important safety and operating instructions.

2. Before using battery charger, read all instructions and cautionary

markings on (1) battery charger, (2) battery pack, and (3) product

using battery pack.

3. CAUTION: To reduce the risk of injury, charge only

Black & Decker Battery Packs. Other types of batteries may burst

causing personal injury and damage.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold by Black &

Decker may result in a risk of fire, electric shock, or injury to

persons.

6. To reduce risk of damage to electric plug and cord, pull by plug

rather than cord when disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped

over, or otherwise subjected to damage or stress.

8. An extension cord should not be used unless absolutely

necessary. Use of improper extension cord could result in a risk

of fire, electric shock or electrocution.

a. Two-wire cords can be used with 2-wire or 3-wire extension

cords. Only round jacketed extension cords should be used, and

we recommend that they be listed by Underwriters Laboratories

(U.L.). If the extension is to be used outside, the cord must be

suitable for outdoor use. Any cord marked for outdoor use can

also be used for indoor work. The letters "W" or "WA" on the cord

jacket indicate that the cord is suitable for outdoor use.

b. An extension cord must have adequate wire size (AWG or

American Wire Gauge) for safety, and to prevent loss of power

and overheating. The smaller the gauge number of the wire, the

greater the capacity of the cable; that is, 16 gauge has more

5

Battery Cap Information

Battery storage and carrying caps are provided for use whenever

the battery is out of the tool or charger. Remove cap before placing

battery in charger or tool.

WARNING: Fire hazard. Do not store or carry battery so that

metal objects can contact exposed battery terminals. For

example, do not place battery in aprons, pockets, tool boxes, product

kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery

terminals inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the like. The US

Department of Transportation Hazardous Material Regulations

(HMR) actually prohibit transporting batteries in commerce or on

airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS

they are properly protected from short circuits. So when transporting

individual batteries, make sure that the battery terminals are

protected and well insulated from materials that could contact them

and cause a short circuit.

Battery Cap

capacity than 18 gauge. When using more than one extension to

make up the total length, be sure each extension contains at least

the minimum wire size.

CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS

NAMEPLATE RATING AMPS – 0 – 10.0

Total Extension Cord

Length (ft) 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

Wire Gauge 18 16 16 14

9. Use only the supplied charger when charging your unit. The use

of any other charger could damage the battery pack or create a

hazardous condition.

10. Use only one charger when charging.

11. Do not attempt to open the charger or the unit. There are no

customer serviceable parts inside. Return to any authorized Black

& Decker service center.

12. DO NOT incinerate battery packs even if they are severely

damaged or completely worn out.

13. Do not incinerate the batteries. They can explode in a fire. A small

leakage of liquid from the battery cells may occur under extreme

usage, charging or temperature

conditions. This does not indicate a failure. However, if the outer

seal is broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean water

for a minimum of 10 minutes and seek immediate medical

attention. MEDICAL NOTE: The liquid is a 25-35% solution of

potassium hydroxide.

6

IMPORTANT CHARGING SAFETY

INSTRUCTIONS

CHARGING PROCEDURE

THE BATTERY PACK IS NOT FULLY CHARGED AT THE

FACTORY. CHARGE BATTERY PACK FOR AT LEAST 9 HOURS

BEFORE USE.

The charger is designed to use standard household 120 volt 60 Hz

power.

1. Plug the charger into any standard 120 Volt 60 Hz electrical

outlet. NOTE: Do not charge by means of an engine

generator or DC power source. Use only 120V AC.

2. Slide the charger onto the battery as

shown in figure 1 and let the battery

charge initially for 9 hours. After the

initial charge, under normal usage, your

battery should be fully charged in 6 to 9

hours.

2a) During charging the green LED will

appear.

2b) When charging is complete the green

LED will go off.

3. Unplug charger, and remove the battery pack. Place the battery

pack into the tool until it “clicks” into place.

NOTE: To remove the battery pack, press down on the release

button on the back of the battery pack and slide out.

IMPORTANT CHARGING NOTES

1. After normal usage, your battery pack should be fully charged in

6 to 9 hours. If the battery pack is run-down completely, it may

take up to 9 hours to become fully charged. Your battery pack

was sent from the factory in an uncharged condition. Before

attempting to use it, it must be charged for at least 9 hours.

2. DO NOT charge the battery pack in an air temperature below

1

7

+40°F(+4.5°C), or above +105°F (+40.5°C). This is important

and will prevent serious damage to the battery pack. Longest life

and best performance can be obtained if battery pack is charged

when air temperature is about 75°F (24°C).

3. While charging, the charger may hum and become warm to

touch. This is a normal condition and does not indicate a

problem.

4. If the battery pack does not charge properly—(1) Check current

at receptacle by plugging in a lamp or other appliance. (2) Check

to see if receptacle is connected to a light switch which turns

power off when you turn out the lights. (3) Move charger and

battery pack to a surrounding air temperature of 40°F (+4.5°C) to

105°F (+40.5°C). (4) If the receptacle and temperature are OK,

and you do not get proper charging, take or send the battery

pack and charger to your local Black & Decker service center.

See Tools Electric in yellow pages.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE using unit with its battery pack in a depleted

condition.

6. The battery pack will reach optimum performance after being

cycled 5 times during normal usage. There is no need to run the

battery pack down completely before recharging. Normal usage

is the best method of discharging and recharging the battery

pack.

STORAGE RECOMMENDATION

1. Store tool:

a.) with the battery pack removed and on the charger.

b.) in a place that is cool and dry away from direct sunlight and excess

heat or cold.

c.) out of the reach of children.

2. For prolonged storage such as over the winter, the battery pack

should be fully charged and then removed from the charger. It

should be charged again just prior to use.

LEAVING THE BATTERY PACK IN THE CHARGER

It is OK to leave battery packs on charge for long periods of time. The

charger has a maintenance mode which gives the battery pack

enough charge to stay “topped off”. If however, the tool is not

expected to be needed for more than 30 days, unplug the charger

and store battery pack in a cool, dry location. NOTE: A battery pack

will lose its charge when kept off of the charger. If the battery pack

has not been kept on maintenance charge, it may need to be

recharged before use. A battery pack may also lose its charge if left in

a charger that is not plugged into an appropriate AC source.

Pole Saw Names and Terms

• Chain Brake - A device used to stop the Pole Saw.

• Drive Sprocket or Sprocket - The toothed part that drives the saw

chain.

• Guide Bar - A solid railed structure that supports and guides the

saw chain.

• Guide Bar Scabbard - Enclosure fitted over guide bar to prevent

tooth contact when saw is not in use.

• Kickback - The backward or upward motion, or both of the guide

bar occurring when the saw chain near the nose of the top area of

the guide bar contacts any object such as a log or branch, or when

the wood closes in and pinches the saw chain in the cut.

• Low-Kickback Chain - A chain that complies with the kickback

performance requirements of ANSI B175.1-1991 (when tested on a

representative sample of chain saws.

• Reduced Kickback Guide Bar - A guide bar which has been

demonstrated to reduce kickback significantly.

• Replacement Saw Chain - A chain that complies with kickback

performance requirements of ANSI B175.1-1991 when tested with

specific chain saws. It may not meet the ANSI performance

requirements when used with other saws.

• Saw Chain - A loop of chain having cutting teeth, that cut the wood,

and that is driven by the motor and is supported by the guide bar.

• Spiked Bumper (Spike) - The pointed tooth or teeth for use when

pruning to pivot the saw and maintain position while sawing.

8

Preparing Your Pole Trimmer for Use

WARNING: Read and understand all instructions. Failure to

follow all instructions listed below may result in electric shock, fire

and/or serious personal injury.

Installing and Removing Saw Chain

WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the handle

before performing the following operations. Failure to do this

could result in serious personal injury.

CAUTION: Sharp moving blade. Always wear protective

gloves when installing or removing the chain. The chain is sharp

and can cut you when it is not running.

• Place the saw on a firm surface.

Rotate the two allen head screws

counterclockwise with the wrench

provided as shown in figure 2.

• Remove sprocket cover, bar clamp,

and allen head screws.

• To remove the chain, rotate the screw

in the front of the housing using the

flat screwdriver end of the wrench as

shown in figure 3. Turning the screw

counterclockwise allows the guide

bar to recede and reduces the

tension on the chain so that it may be

removed.

• Lift the worn chain out of the groove

in the guide bar.

• Flip guide bar over.

• To replace the chain, check to make

sure that the slot in the guide bar is

over the two location pins shown in

figure 3A and that the hole below the

slot is located over the adjustment

pin.

Features

Before using your Pole Saw familiarize yourself with all operating and

safety features.

5

4

3

2

1

11

10

9

8

7

6

A. Handle Module

B. Center Extension

C. Saw Head Module

1. Trigger Switch

2. Lock Button

3. Battery

4. Foam Gripper

5. Threaded Pole

6. Threaded Sleeve

7. Center Extension Pole

8. Sprocket Cover (other side)

9. Allen Head Screws (other side)

10. Guide Bar

11. Saw Chain

12. Scabbard

13. Allen Wrench

14. Oil Bottle

6

A

B

C

12

13

14

2

3

3A

LOCATING PINS

ADJUSTMENT PIN

• Switch - A device that when operated will complete or interrupt an

electrical power circuit to the motor of the chain saw.

• Switch Lockout - A movable stop that prevents the unintentional

operation of the switch until manually actuated.

• Trimming (Pruning) - Process of cutting limbs from a tree.

• Undercut - An upward cut from underside of a log or limb.This is done

while in normal cutting position and cutting with top of guide bar.

9

• Place new chain in groove of guide bar and around sprocket. Make

sure saw teeth are facing correct direction by matching arrow on

chain with graphic on housing shown here.

• Rotate the screw in the front of the housing clockwise to increase

the chain tension as in Figure 3.

• Replace sprocket cover, bar clamp, and allen head screws.

• Follow instructions for adjusting the chain tension.

Adjusting Chain Tension

• With the saw still on a firm surface check the chain tension. The

tension is correct when the chain snaps back after being pulled

1/8 in. (3mm) away from the chain

bar with light force from the middle

finger and thumb as shown in

figure 4. There should be no “sag”

between the guide bar and the chain

on the underside as shown in

figure 5.

• To adjust saw chain tension, loosen

allen head screws.

• Rotate the screw in the front of the

housing using the flat screwdriver end

of the wrench as shown in figure 3.

• Do not over-tension the chain as this will

lead to excessive wear and will reduce

the life of the bar and chain.

Overtensioning also reduces the amount of cuts you will get per

battery charge.

• Once chain tension is correct, tighten allen head screws to clamp

bar.

• When the chain is new check the tension frequently (after

disconnecting battery) during the first 2 hours of use as a new chain

stretches slightly.

Chain Oiling

• A high quality bar and chain oil or

SAE30 weight motor oil should be

used for chain and bar lubrication. The

use of a vegetable based bar and chain

oil is recommended when pruning

trees. Mineral oil is not recommended

because it may harm trees. Never use

waste oil or very thick oil. These may

damage your chain saw.

• Lubricate the whole chain evenly

before each use as shown in figure 6.

Also lubricate the chain whenever

replacing a fully discharged battery with

a fully charged one.

Transporting Pole Saw

• Always remove the battery pack from the

handle (figure 7) and cover the chain with the

scabbard (figure 8) when transporting the

Pole Saw. See page 5 for additional

information on transporting the battery.

5

4

6

7

8

Joining Center Extension to Saw Head Module and

Handle Module

Adding the extension (B) to the handle module (A) and saw head

module (C) creates a Pole Saw that is approximately 9 foot in length

as shown in figure 13.

To attach the middle module to the handle module and saw head

module:

1. Align the groove on the outside of the

coupling end of the handle module (A)

with the tongue on the inside of the

coupling end of the center extension (B).

See figure 14. Push the two sections

completely together.

2. Slide the threaded sleeve (6) (figure

15) on the center extension down as far

as possible and rotate the sleeve

clockwise until it stops and completely

covers the orange threads as shown in

figure 16.

3. Repeat steps 1 and 2 above to attach

the saw head module to the center

extension.

WARNING: Always check to make

sure that the sleeve is completely

threaded on and that the orange threads are no longer visible.

Not threading the sleeve completely on could result in the modules

becoming disconnected creating a hazardous condition.

Periodically check the connections to insure that no orange threads

are visible.

Groove

14

15

16

13

10

Assembly

Joining Saw Head Module to 18V Handle Module

WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the handle

and that the protective scabbard is in place on the chain before

performing the following operations. Failure to do this could result

in serious personal injury.

The three modules which make up the 18V Pole Saw are keyed to

insure correct assembly. If a module does not smoothly attach to

another do not force fit.

Combining the handle module (A) to the saw head module (C)

creates a pole saw that is approximately 6 foot in length as shown in

figure 9.

To attach the handle module to the saw head module:

1. Align the groove on the outside of the coupling end of the handle

module (A) with the tongue on the

inside of the coupling end of the saw

head module (C). See figure 10. Push

the two sections completely together.

2. Slide the threaded sleeve (6) figure 11

on the saw head module down as far as

possible and rotate the sleeve clockwise

until it stops and completely covers the

orange threads as shown in figure 12.

WARNING: Always check to make

sure that the sleeve is completely

threaded on and that the orange

threads are no longer visible. Not

threading the sleeve completely on

could result in the modules becoming

disconnected creating a hazardous

condition. Periodically check the

connections to insure that no orange

threads are visible.

Groove

10

11

12

9

11

Disassembly

Detaching Saw Head Module

WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the handle

and that the protective scabbard is in place on the chain before

performing the following operations. Failure to do this could result

in serious personal injury.

When detaching the modules, whether it is in the two

module or three module mode, always detach the

saw head module first. To do this, rest the handle

module on the ground and grasp the center of the

saw head module with

one hand figure 17. Use

your other hand to loosen

the threaded sleeve

figure 18 and then pull

the two halves apart.

Repeat this process if the center extension

was attached.

Operating the Pole Saw

WARNING: Read and understand all

instructions. Failure to follow all

instructions listed below may result in

electric shock, fire and/or serious personal

injury.

Connecting the Battery

Place the battery in the tool as shown in

figure 19 and be certain that it is inserted

fully into the tool cavity until it “clicks” into

place. To remove the battery from the tool,

press down on the release button on the

back of the battery (figure 20) and slide

out.

20

17

18

19

Switch

Always be sure of your footing and grip the

Pole Saw firmly with both hands with the

thumb and fingers encircling the handle.

To turn the tool ON pull the lock button (1)

back with your thumb and then squeeze

the trigger (2) with your fingers as shown

in figure 21. (Once the tool is running you

can release the lock button.) To turn the

tool OFF, release the trigger.

Auto-Stop Chain Braking System

Your chain saw is fitted with an auto-stop chain braking system which

will stop the chain quickly each time you release the rear trigger, or if

kickback should occur. This system should be tested before every

use.

21

12

Pruning With the Pole Saw

Warning: When pruning trees:

• Guard Against Kickback which can result in

severe injury or death. See “KICKBACK”,

page 3 to avoid the risk of kickback.

• Do not overreach. Make sure your footing is

firm. Keep feet apart. Divide your weight evenly

on both feet.

• Use both hands to grip Pole Saw as shown

in figure 22. Use a firm grip. Thumbs and

fingers must wrap around Pole Saw handle and

pole. Keep fingers away from

sawdust exhaust chute shown in

figure 22a.

• Never operate while in a tree, in

any awkward position or on a

ladder or other unstable surface.

You may lose control of Pole Saw

causing severe injury.

Follow directions below to trim a tee.

1. Make sure Pole Saw is running at full speed before making a cut.

When starting a cut, place moving chain against limb. Hold Pole

Saw firmly in place to avoid

possible bouncing or skating

(sideways movement) of Pole

Saw.

2. Guide Pole Saw using light

pressure. Make first cut six inches

from tree trunk on underside of

limb. Use top of guide bar to make

this cut. Cut 1/3 through diameter

of limb. Then make the finish cut

from the top as shown in figure

23.

22

22a

23

Pole Saw Trimming /

Pruning

Warnings:

• Never stand directly

under the limb you

are cutting. Always

position yourself out of

the path of falling

debris.

• Always wear head,

eye, foot and body

protection. Wearing

body protection helps

reduce the risk of

injury when operating

this unit.

• Never

stand on a

ladder or

other

unstable

support

while using the Pole

Saw. Always avoid

any position which can

cause you to loose your balance and cause severe injury.

• Keep other persons at least 50 feet (15m) from the

work area. Distractions can cause you to lose control.

• Electrocution Hazard. To prevent shock, do not

operate within 50 feet (15m) of overhead electrical

lines. Always check surrounding area for hidden

electrical lines.

• Do not extend Pole Saw switch handle above

shoulder height.

Always Wear:

Head Protection

Eye Protection

Work Gloves

Long Pants

Steel Toed Shoes

Operating Position

13

If you try to cut off thick branches

from the bottom, the branch may

close in and pinch the saw chain

in the cut. If you try to cut off thick

branches from the top, without a

shallow undercut, the branch may

splinter figure 24.

Do not force Pole Saw. The motor

will overload and can burn out. It

will do the job better and safer at

the rate for which it was intended.

3. Remove Pole Saw from cut while

it is running at full speed. Stop Pole Saw by releasing trigger.

Make sure chain has stopped before setting Pole Saw down.

Saw chain sharpness

The cutters will dull immediately if they touch the ground or a nail

while cutting.

Saw chain tension

This should be done regularly. Refer to page 8 “Adjusting Chain

Tension”.

Pole Saw Maintenance Section

Regular maintenance ensures a long effective life for the tool.

After every 10 minutes of use be sure to remove the battery (be

aware the chain and bar can be hot!) check the bar and chain for

correct tension and lubricate per pole saw instruction manual.

Use only mild soap and damp cloth to clean the tool. Never let any

liquid get inside the tool; never immerse any part of the tool into a

liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs,

maintenance and adjustment should be performed by authorized

service centers or other qualified service organizations, always using

identical replacement parts.

24

Accessories

Replacement chain and bar are available from your nearest Black &

Decker service center.

Replacement chain # 623382-00, Replacement bar # 623381-00

The use of accessories not recommended in this manual may be

hazardous.

Troubleshooting Section

If your Pole Saw does not operate correctly check the following:

Problem

Possible Cause Possible Solution

• Tool will not

start.

• Unit will not

charge.

• Bar / chain

overheated.

• Battery not

installed properly.

• Battery not

charged.

• Lock-out button not

actuated.

• Pole connections

not properly

tightened.

• Battery not

inserted into

charger.

• Chain too tight.

• Lubrication

needed.

• Check battery installation.

• Check battery charging

requirements.

• Pull back on lock

button/actuate trigger.

• Refer to instruction manual

for pole connections.

• Insert battery into charger

until green LED appears.

Charge up to 9 hours if

battery totally drained.

• Refer to section on

adjusting chain tension.

• Refer to sections for chain

oiling application.

• Chain is

loose.

• Chain tension set

incorrectly.

• Refer to section for chain

tensioning.

14

Service Information

All Black & Decker Service Centers are staffed with trained personnel

to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory

replacement parts, contact the Black & Decker location nearest you.

To find your local service location, refer to the yellow page directory

under "Tools—Electric" or call: 1-800-544-6986 or visit

www.blackanddecker.com.

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against

any defects in material or workmanship. The defective product will be

replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product

to the retailer from whom it was purchased (provided that the store is

a participating retailer). Returns should be made within the time

period of the retailerʼs policy for exchanges (usually 30 to 90 days

after the sale). Proof of purchase may be required. Please check with

the retailer for their specific return policy regarding returns that are

beyond the time set for exchanges.

Troubleshooting Section Con’t.

Problem Possible Cause Possible Solution

• Unit runs but

does not cut.

• Chain installed

backwards.

• Refer to sections for

installing and removing

chain.

See ʻTools-Electricʼ

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD

21286 U.S.A.

The second option is to take or send the product (prepaid) to a Black

& Decker owned or authorized Service Center for repair or

replacement at our option. Proof of purchase may be required.Black

& Decker owned and authorized Service Centers are listed under

"Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you

specific legal rights and you may have other rights which vary from

state to state or province to province. Should you have any

questions, contact the manager of your nearest Black & Decker

Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-544-6986 for a free

replacement.

LATIN AMERICA: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, check country

specific warranty information contained in the packaging, call the local

company or see the website for warranty information.

• Poor cut

quality.

• Chain tension set

incorrectly.

• Chain needs

replacement.

• Refer to section on

adjusting chain tension.

Note: Excessive tension

leads to excessive wear

and reduction in life of bar

& chain.

Lubricate after every 10

minutes of use.

Refer to section for

installation of chain.

Page is loading ...

47

· GARANTÍA BLACK & DECKER · BLACK & DECKER WARRANTY

. SOLAMENTE PARA PROPOSITOS DE MEXICO

Distributor Name · Sello firma del distribuidor

Date of purchase · Fecha de compra Invoice No. · No. de factura

PRODUCT INFOMATION · IDENTIFICACION DEL PRODUCTO

Cat. No. · Catalogo ó Modelo Serial Number · No. de serie

Name · Nombre Last Name · Apellido

Address · Dirección

City · Ciudad State · Estado

Postal Code · Código Postal Country · País

Telephone · No. Teléfono

Page is loading ...

Black & Decker NPP2018 User manual

Black & Decker NPP2018 User manual

in other languages

Related papers

Other documents