Hotpoint Ariston FK 103E P.20 X/HA S User guide

English

Operating Instructions

OVEN

Français

Mode d’emploi

FOUR

Español

Manual de instrucciones

HORNO

Italiano

Istruzioni per l’uso

FORNO

Portuges

Instruções para a utilização

FORNO

Sommario

Istruzioni per l’uso,1

Avvertenze,2

Assistenza,5

Descrizione dell’apparecchio,7

Descrizione dell’apparecchio,8

Installazione,10

Avvio e utilizzo,12

Programmi,13

Precauzioni e consigli,17

Manutenzione e cura,17

Anomalie e rimedi,19

Contents

Operating Instructions,1

Warnings,2

Assistance,5

Description of the appliance,7

Description of the appliance,8

Installation,20

Start-up and use,22

Modes,23

Precautions and tips,27

Maintenance and care,27

Troubleshooting,29

Sommaire

Mode d’emploi,1

Avertissements,2

Assistance,5

Description de l’appareil,7

Description de l’appareil,8

Installation,30

Mise en marche et utilisation,32

Programmes,33

Précautions et conseils,37

Nettoyage et entretien,37

Anomalies et remèdes,39

Sumario

Manual de instrucciones,1

Advertencias,3

Asistencia,6

Descripción del aparato,7

Descripción del aparato,8

Instalación,40

Puesta en funcionamiento y uso,42

Programas,43

Precauciones y consejos,48

Mantenimiento y cuidados,48

Anomalías y soluciones,50

Índice

Instruções para a utilização,1

Advertências,3

Assistência,6

Descrição do aparelho,7

Descrição do aparelho,9

Instalação,51

Início e utilização,53

Programas,54

Precauções e conselhos,59

Manutenção e cuidados,59

Anomalias e soluções,61

FK 1039E .20 X/HA

FK 103EL .20 X/HA S

FK 103EN C X/HA S

FK 103E.20 X/HA S

FK 103ELS .20 X/HA

2

Avvertenze

ATTENZIONE: Questo apparecchio e le

sue parti accessibili diventano molto caldi

durante l’uso. Bisogna fare attenzione ed

evitare di toccare gli elementi riscaldanti.

Tenere lontani i bambini inferiori agli 8

anni se non continuamente sorvegliati.

Il presente apparecchio può essere

utilizzato dai bambini a partire dagli 8

anni e da persone con ridotte capacità

siche, sensoriali o mentali oppure con

mancanza di esperienza e di conoscenza

se si trovano sotto adeguata sorveglianza

oppure se sono stati istruiti circa l’uso

dell’apparecchio in modo sicuro e se

si rendono conto dei pericoli correlati.

I bambini non devono giocare con

l’apparecchio. Le operazioni di pulizia

e di manutenzione non devono essere

effettuate dai bambini senza sorveglianza.

Non utilizzare prodotti abrasivi né spatole

di metallo taglienti per pulire lo sportello

in vetro del forno in quanto potrebbero

grafare la supercie, provocando, così,

la frantumazione del vetro.

Non utilizzare mai pulitori a vapore o ad alta

pressione per la pulizia dell’apparecchio.

ATTENZIONE: Assicurarsi che

l’apparecchio sia spento prima di sostituire

la lampada per evitare la possibilità di

scosse elettriche.

! Quando si inserisce la griglia assicurarsi

che il fermo sia rivolto verso l’alto e nella

parte posteriore della cavità.

Warnings

WARNING: The appliance and its

accessible parts become hot during use.

Care should be taken to avoid touching

heating elements. Children less than 8

years of age shall be kept away unless

continuously supervised. This appliance

can be used by children aged from 8 years

and above and persons with reduced

physical, sensory or mental capabilities

or lack of experience and knowledge

if they have been given supervision

or instruction concerning use of the

appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and

user maintenance shall not be made by

children without supervision.

Do not use harsh abrasive cleaners or

sharp metal scrapers to clean the oven door

glass since they can scratch the surface,

which may result in shattering of the glass.

Never use steam cleaners or pressure

cleaners on the appliance.

WARNING: Ensure that the appliance is

switched off before replacing the lamp to

avoid the possibility of electric shock.

! When you place the rack inside, make

sure that the stop is directed upwards and

in the back of the cavity.

Avertissements

ATTENTION : Cet appareil ainsi que

ses parties accessibles deviennent très

chauds pendant leur fonctionnement.

Il faut faire attention à ne pas toucher

Page is loading ...

5

Assistenza

Attenzione:

L’apparecchio è dotato di un sistema di diagnostica automatica

che consente di rilevare eventuali malfunzionamenti. Questi

vengono comunicati dal display tramite messaggi del tipo:

“F--” seguito da numeri.

In questi casi è necessario l’intervento dell’assistenza

tecnica.

Prima di contattare l’Assistenza:

• Verificare se l’anomalia può essere risolta

autonomamente;

• Riavviare il programma per controllare se l’inconveniente

è stato ovviato;

• In caso negativo, contattare il Servizio Assistenza

Tecnico Autorizzato.

! Non ricorrere mai a tecnici non autorizzati.

Comunicare:

• Il tipo di anomalia;

• il messaggio visibile sul display TEMPERATURA

• Il modello della macchina (Mod.)

• Il numero di serie (S/N)

Queste ultime informazioni si trovano sulla targhetta

caratteristiche posta sull’apparecchio

Assistenza Attiva 7 giorni su 7

Se nasce il bisogno di assistenza o manutenzione basta

chiamare il Numero Unico Nazionale 199.199.199* per

essere messi subito in contatto con il Centro Assistenza

Tecnica più vicino al luogo da cui si chiama.

È attivo 7 giorni su 7, sabato e domenica compresi, e non

lascia mai inascoltata una richiesta.

Estensione di garanzia Airbag

Airbag è il servizio esclusivo creato da Ariston che integra e

prolunga nel tempo i contenuti della garanzia standard: con una

modica cifra protegge il cliente da ogni imprevisto riguardante

l’assistenza e la manutenzione dell’elettrodomestico. Per i 5

anni successivi alla data di acquisto il cliente che aderisce al

programma Airbag avrà diritto gratuitamente a:

• l’intervento entro 48 ore dalla chiamata;

• il contributo per spese di trasferta del Tecnico (diritto di

chiamata);

• la manodopera;

• le parti di ricambio originali;

• il trasporto dell’elettrodomestico non riparabile in loco.

Inoltre, qualora l’elettrodomestico non sia riparabile la

garanzia prevede la sostituzione a prezzo agevolato in

funzione dell’anzianità del prodotto.

* Al costo di 14,25 centesimi di Euro al minuto (iva inclusa)

dal Lun. al Ven. dalle 08:00 alle 18:30, il Sab. dalle 08:00

alle 13:00 e di 5,58 centesimi di Euro al minuto (iva inclusa)

dal Lun. al Ven. dalle 18:30 alle 08:00, il Sab. dalle 13:00

alle 08:00 e i giorni festivi, per chi chiama dal telefono sso.

Per chi chiama da radiomobile le tariffe sono legate al piano

tariffario dell’operatore telefonico utilizzato.

Le suddette tariffe potrebbero essere soggette a variazione

da parte dell’operatore telefonico; per maggiori informazioni

consultare il sito www.indesit.com.

Assistance

Warning:

The appliance is tted with an automatic diagnostic system

which detects any malfunctions. Malfunctions are signalled

through messages of the following type: “F—” followed by

numbers.

Call for technical assistance in the event of a malfunction.

Before calling for Assistance:

• Check whether you can x the problem yourself.

• Restart the programme to check whether the malfunction

has disappeared.

• If it has not, contact the Authorised Technical Assistance

Service.

! Never use the services of an unauthorised technician.

Please have the following information to hand:

• The type of problem encountered.

• The message shown on the TEMPERATURE display.

• The appliance model (Mod.).

• The serial number (S/N).

The latter two pieces of information can be found on the

data plate located on the appliance.

Assistance

Attention :

L’appareil dispose d’un système d’autotest qui permet de

détecter toute anomalie de fonctionnement. Ces anomalies

sont afchées sous la forme: «F—» suivi de chiffres.

Contacter alors un service d’assistance technique.

Avant d’appeler le service de dépannage :

• Vérier s’il est possible de résoudre le problème soi-

même ;

• Redémarrer le programme pour contrôler si le problème

a été résolu;

Page is loading ...

7

Descrizione dell’apparecchio

Vista d’insieme

1 POSIZIONE 1

2 POSIZIONE 2

3 POSIZIONE 3

4 POSIZIONE 4

5 POSIZIONE 5

6 GUIDE di scorrimento dei ripiani

7 Ripiano LECCARDA

8 Ripiano GRIGLIA

9 Pannello di controllo

Description of the appliance

Overall view

1 POSITION 1

2 POSITION 2

3 POSITION 3

4 POSITION 4

5 POSITION 5

6 GUIDES for the sliding racks

7 DRIPPING PAN

8 GRILL

9 Control panel

Description de l’appareil

Vue d’ensemble

1 NIVEAU 1

2 NIVEAU 2

3 NIVEAU 3

4 NIVEAU 4

5 NIVEAU 5

6 GLISSIERES de coulissement

7 Support LECHEFRITE

8 Support GRILLE

9 Tableau de bord

Descripción del aparato

Vista en conjunto

1 POSICIÓN 1

2 POSICIÓN 2

3 POSICIÓN 3

4 POSICIÓN 4

5 POSICIÓN 5

6 GUÍAS de deslizamiento de las bandejas

7 Bandeja GRASERA

8 Bandeja PARRILLA

9 Panel de control

Descrição do aparelho

Vista de conjunto

1 POSIÇÃO 1

2 POSIÇÃO 2

3 POSIÇÃO 3

4 POSIÇÃO 4

5 POSIÇÃO 5

6 GUIAS de escorrimento das prateleiras

7 Prateleira BANDEJA PINGADEIRA

8 Prateleira GRADE

9 Painel de comandos

7

8

9 6

1

2

3

4

5

8

Descrizione dell’apparecchio

Pannello di controllo

1 Icone PROGRAMMI MANUALI

2 Display TEMPERATURA

3 Icona TEMPERATURA

4 Icona DURATA

5 Display TEMPI

6 Icona FINE COTTURA

7 Icona BLOCCO COMANDI

8 AVVIO/ARRESTO

9 Icona LUCE

10 Icona OROLOGIO

11 Icona CONTAMINUTI

12 Icone REGOLAZIONE TEMPI/TEMPERATURA

13 Icone PRERISCALDAMENTO/CALORE RESIDUO

14 Icone PROGRAMMI AUTOMATICI/ECO

15 ACCENSIONE PANNELLO

Description of the appliance

Control panel

1 MANUAL COOKING MODE Icons

2 TEMPERATURE display

3 TEMPERATURE icon

4 DURATION icon

5 TIME display

6 END OF COOKING Icon

7 CONTROL PANEL LOCK icon

8 START / STOP

9 LIGHT icon

10 CLOCK icon

11 MINUTE MINDER Icon

12 TIME / TEMPERATURE ADJUSTMENT Icons

13 PREHEATING / RESIDUAL HEAT icons

14 AUTOMATIC/ECO COOKING MODE icons

15 CONTROL PANEL POWER BUTTON

Description de l’appareil

Tableau de bord

1 Icônes PROGRAMMES MANUELS

2 Afcheur TEMPERATURE

3 Icône TEMPÉRATURE

4 Icône DURÉE

5 Afcheur TEMPS

6 Icône FIN CUISSON

7 Icône VERROUILLAGE COMMANDES

8 DÉPART / ARRÊT

9 Icône ECLAIRAGE

10 Icône HORLOGE

11 Icône MINUTEUR

12 Icônes RÉGLAGE TEMPS / TEMPÉRATURE

13 Icône PRÉCHAUFFAGE / CHALEUR RÉSIDUELLE

14 Icônes PROGRAMMES AUTOMATIQUES / ECO

15 ALLUMAGE PANNEAU

Descripción del aparato

Panel de control

1 Iconos de PROGRAMAS MANUALES

2 Display de TEMPERATURA

3 Icono TEMPERATURA

4 Icono de DURACIÓN

5 Display de TIEMPOS

6 Icono de FIN DE COCCIÓN

7 Icono BLOQUEO DE MANDOS

8 PUESTA EN MARCHA / PARADA

9 Icono LUZ

10 Icono RELOJ

11 Icono CONTADOR DE MINUTOS

12 Iconos PROGRAMACIÓN DE TIEMPOS /

TEMPERATURA

13 Iconos PRECALENTAMIENTO / CALOR RESIDUAL

14 Iconos de PROGRAMAS AUTOMÁTICOS / ECO

15 ENCENDIDO DEL PANEL

10

11

12

13

14

1

2

43

7

6

5

8

9

15

Page is loading ...

20

GB

Installation

! Please keep this instruction booklet in a safe place for

future reference. If the appliance is sold, given away or

moved, please make sure the booklet is also passed on to

the new owners so that they may benet from the advice

contained within it.

! Please read this instruction manual carefully: it contains

important information concerning the safe operation,

installation and maintenance of the appliance.

Positioning

! Do not let children play with the packaging material; it

should be disposed of in accordance with local separated

waste collection standards (see Precautions and tips).

! The appliance must be installed by a qualied professional

in accordance with the instructions provided. Incorrect

installation may damage property or cause harm to people

or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance

operates properly:

• The panels adjacent to the oven must be made of heat-

resistant material.

• Cabinets with a veneer exterior must be assembled with

glues which can withstand temperatures of up to 100°C.

• To install the oven under the counter (see diagram) or

in a kitchen unit, the cabinet must have the following

dimensions:

590 mm.

595 mm.

22,5 mm.*

20,5 mm.

550 mm.

570 mm.

20 mm.

575-585 mm.

45 mm.

560 mm.

550 mm.

min.

* Stainless steel models only

! The appliance must not come into contact with electrical

parts once it has been installed.

The indications for consumption given on the data plate

have been calculated for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the

cabinet must be removed. It is advisable to install the oven

so that it rests on two strips of wood, or on a completely

at surface with an opening of at least 45 x 560 mm (see

diagrams).

560 mm.

45 mm.

Centring and xing

Secure the appliance to the cabinet:

• Open the oven door.

• Remove the 2 rubber plugs covering the xing holes on

the perimeter frame.

• Fix the oven to the cabinet using the 2 wood screws.

• Replace the rubber plugs.

! All parts which ensure the safe operation of the appliance

must not be removable without the aid of a tool.

GB

21

Electrical connection

Ovens equipped with a three-pole power supply cable are

designed to operate with alternating current at the voltage

and frequency indicated on the data plate located on the

appliance (see below).

Fitting the power supply cable

1. Open the terminal board

by inserting a screwdriver

into the side tabs of the

cover. Use the screwdriver

as a lever by pushing it

down to open the cover (see

diagram).

2. Install the power supply

cable by loosening the

cable clamp screw and the

three wire contact screws

L-N- .

Connect the wires to the

corresponding terminals:

the Blue wire to the terminal

marked (N), the Brown wire

to the terminal marked (L)

and the Yellow/Green wire

to the terminal marked

(see diagram).

3. Secure the cable by fastening the clamp screw.

4. Close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (see table).

The appliance must be directly connected to the mains using

an omnipolar switch with a minimum contact opening of 3

mm installed between the appliance and the mains. The

switch must be suitable for the charge indicated and must

comply with current electrical regulations (the earthing wire

must not be interrupted by the switch). The supply cable

must be positioned so that it does not come into contact

with temperatures higher than 50°C at any point (the back

panel of the oven, for example).

! The installer must ensure that the correct electrical

connection has been performed and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply, make

sure that

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate.

• The voltage is in the range between the values indicated

on the data plate.

N

L

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

APPLIANCE SPECIFICATIONS

Dimensions*

width 43.5 cm

height 32,4 cm

depth 41.5 cm

Volume*

59 l

Dimensions**

width 45.5 cm

height 32,4 cm

depth 41.5 cm

Volume**

62 l

Electrical

connections

voltage: 220 - 240 V~ 50/60 Hz or

50 Hz (see data plate)

maximum power absorbed

2800 W

ENERGY

LABEL

Directive 2002/40/EC on the label

of electric ovens. Standard EN 50304

Declared energy consumption

for Forced convection Class –

heating mode:

ECO.

* Only for models with drawn rails.

** Only for models with wire rails.

This appliance conforms to the following

European Economic Community

directives:

- 2006/95/EEC dated 12/12/06 (Low

Voltage) and subsequent amendments.

- 2004/108/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments.

- 93/68/EEC dated 22/07/93 and

subsequent amendments.

- 2012/19/EC and subsequent

amendments.

- 1275/2008 standby/off mode.

22

GB

Start-up and use

WARNING! The oven is

provided with a stop system

to extract the racks and

prevent them from coming

out of the oven (1).

As shown in the drawing,

to extract them completely,

simply lift the racks, holding

them on the front part, and

pull (2).

! The rst time you use your appliance, heat the empty oven

with its door closed at its maximum temperature for at least

half an hour. Make sure that the room is well ventilated

before switching the oven off and opening the oven door.

The appliance may emit a slightly unpleasant odour caused

by protective substances used during the manufacturing

process burning away.

! To make the setting process easier, press and hold the and

buttons to scroll through the numbers on the display rapidly.

! Each setting will automatically be stored in the appliance

memory after 10 seconds.

! The touch controls cannot be activated if the user is

wearing gloves.

Some models are equipped with a system of hinges which

allows the door to close slowly, without the user having to

follow the movement through with his/her hand. To use the

system correctly, before closing the door:

• Open the door fully.

• Do not force the closing movement manually.

! In order to optimise the cooking performance, when

starting the selected function, product settings will be

applied that could cause a delayed start of the fan and

heating elements

Control panel lock

! The control panel can be locked while the oven is off, once

cooking has started or nished and during programming.

To lock the oven controls, press and hold the button

for at least 2 seconds. A buzzer will sound and the

TEMPERATURE display shows the key symbol “O—n”. The

icon will light up to indicate lock activation.

To deactivate the lock, press and hold the button again

for at least 2 seconds.

Setting the clock

! The clock can only be set when the oven is switched off. If

the oven is in standby mode, pressing the button once will

display the current time setting. Press it again to set the time.

After connection to the power supply network or after

a blackout, the button and the digits on the TIME display

will ash for 10 seconds.

To set the clock:

1. Press the button.

2. Adjust the hour gure using the “ ” and “ ” buttons.

3. Once you have reached the correct hour value, press

the button.

4. Repeat the above process to set the minutes.

If a blackout occurs, it will be necessary to reset the clock.

If the icon ashes on the display, this indicates that the

clock has not been set correctly.

Setting the minute minder

! The minute minder may be set regardless of whether the

oven is switched on or off. It does not switch the oven on or off.

When the set time has elapsed, the timer emits a buzzer

that will automatically stop after 30 seconds or when any

active button on the control panel is pressed.

To adjust the timer proceed as follows:

1. Press button .

2. Set the desired time using buttons “ ” and “ ”.

3. Once you have reached the desired value, press the

button again.

The lit symbol will remind you that the minute minder is on.

To cancel the minute minder, press the button and

use the “ ” and “ ” buttons to set the time to 00:00. Press

button again.

The icon will switch off to indicate that the minute minder

has been disabled.

Starting the oven

1. Switch the control panel on by pressing the button.

The appliance buzzer sounds three times (ascending) and

all buttons light up in sequence.

2. Press the button corresponding to the desired cooking

mode. The TEMPERATURE display shows:

- the temperature associated with the mode, if programming

manually;

- “Auto”, if programming is automatic.

The TIME display shows:

- the current time, if programming manually;

- the duration, if programming is automatic.

3. Press the button to begin cooking.

4. The oven will begin its preheating phase, the preheating

indicators will light up as the temperature rises.

5. When the preheating process has nished, a buzzer sounds

and all the preheating indicator lights show that this stage has

been completed: the food can then be placed in the oven.

6. During cooking it is always possible to:

- change the temperature by pressing the button,

followed by the “ ” and “ ” buttons (manual modes only);

- set the duration of a cooking mode (see Cooking Modes);

- press the button to stop cooking. In this case the

appliance stores the temperature modied previously in its

memory (manual modes only);

- switch off the oven by pressing the button for 3 seconds.

7. If a blackout occurs while the oven is already in operation,

an automatic system within the appliance will reactivate the

cooking mode from the point at which it was interrupted,

provided that the temperature has not dropped below a

GB

23

certain level. Programmed cooking modes which have not

yet started will not be restored and must be reprogrammed

(for example: a cooking mode has been programmed to

start at 20:30. At 19:30 a blackout occurs. When the power

supply is restored, the mode will have to be reprogrammed).

! There is no preheating stage for the GRILL mode.

! Never put objects directly on the bottom of the oven; this

will prevent the enamel coating from being damaged.

! Always place cookware on the rack(s) provided.

Cooling ventilation

In order to cool down the external temperature of the oven,

a cooling fan blows a stream of air between the control

panel and the oven door, as well as towards the bottom of

the oven door.

! Once cooking has been completed, the cooling fan continues

to operate until the oven has cooled down sufciently.

Oven light

The light comes on when the oven door is opened or when

a cooking mode starts.

When models featuring LED INSIDE technology begin

cooking, the LEDs on the door light up for improved

illumination of all cooking levels.

The button can be used to switch on the light at any time.

Residual heat indicators

The appliance is tted with a residual heat indicator. When

the oven is off, the “residual heat” bar on the display lights

up to indicate high temperatures inside the oven cavity. The

individual segments of the bar switch off one by one as the

temperature inside the oven falls.

Concealed handle

Some models have a concealed handle built into the oven

door. Simply press lightly and the push/push opening will

improve your grip when opening and closing the oven.

When you have nished using it, close it again by applying

light pressure.

Demo mode

The oven can operate in the DEMO mode: all heating

elements are deactivated, and the controls remain operative.

To activate DEMO mode, press and release button ,

then buttons and simultaneously for 6 seconds, and

then press and release button . A buzzer sounds and

the TEMPERATURE display shows “dEon”.

To deactivate DEMO mode, when the oven is off press and

hold button and button simultaneously for 3 seconds.

A buzzer sounds and the “dEoF” message disappears from

the display.

Restoring the factory settings

The oven factory settings can be restored to reset all

selections made by the user (clock and customised

durations). To carry out a reset, switch off the oven, then

press and hold the button corresponding to the rst manual

cooking mode (top left) and the button simultaneously

for 6 seconds. Once the restore procedure is complete, a

buzzer will sound. The rst time the button is pressed, the

oven will behave as if it is being switched on for the rst time.

Standby

This product complies with the requirements of the latest

European Directive on the limitation of power consumption

of the standby mode. If no buttons are pressed for 30

minutes and the control panel/door lock has not been

activated, the appliance automatically reverts to standby

mode. Standby mode is indicated by the high luminosity

“Clock button” light. As soon as interaction with the machine

resumes, the system’s operating mode is restored.

Modes

! In order to guarantee wonderfully soft and crunchy

foodstuffs, the oven releases – in the form of water vapour -

the humidity naturally withheld in the food itself. In this way,

optimal cooking results can be achieved for all types of food.

! Every time the oven is switched on, it suggests the rst

manual cooking mode.

Manual cooking modes

! All cooking modes have a default cooking temperature

which may be adjusted manually to a value between

30°C and 250°C as desired (300°C for GRILL mode). Any

temperature adjustments will be stored in the appliance

memory and suggested again the next time this mode

is used. If the selected temperature is lower than the

temperature inside the oven, the text “Hot” appears on the

TEMPERATURE display. However, it will still be possible

to start cooking.

MULTILEVEL mode

All heating elements and the fan are activated. Since the

heat remains constant throughout the oven, the air cooks

and browns food in a uniform manner. A maximum of two

racks may be used at the same time.

BARBECUE mode

The top heating element and the rotisserie spit (where

present) are activated. The high and direct temperature

of the grill is recommended for food which requires a high

surface temperature. Always cook in this mode with the oven

door closed (see “Practical cooking advice”).

FAN GRILLING mode

24

GB

The top heating element and the rotisserie spit (where

present) are activated and the fan begins to operate.

During part of the cycle the circular heating element is

also activated. This combination of features increases the

effectiveness of the unidirectional thermal radiation provided

by the heating elements through the forced circulation of

the air throughout the oven.

This helps prevent food from burning on the surface and

allows the heat to penetrate right into the food. Always

cook in this mode with the oven door closed (see “Practical

cooking advice”).

LOW TEMPERATURE modes

This type of cooking can be used for proving, defrosting,

preparing yoghurt, heating dishes at the required speed and

slow cooking at low temperatures. The temperature options

are: 40, 65 and 90°C.

PIZZA modes

The top and circular heating elements switch on and the fan

begins to operate. This combination heats the oven rapidly.

If you use more than one rack at a time, switch the position

of the dishes halfway through the cooking process.

BAKING mode

The rear heating element and the fan are switched on, thus

guaranteeing the distribution of heat in a delicate and uniform

manner throughout the entire oven. This mode is ideal for baking

temperature sensitive foods (such as cakes, which need to rise).

ECO mode

The rear heating element and the fan are switched on,

thus guaranteeing the distribution of heat in a delicate and

uniform manner throughout the entire oven.This energy

saving mode is recommended for small dishes, ideal for

heating foods and nishing off cooking.

Rotisserie spit*

To operate the rotisserie function (see diagram) proceed as

follows:

1. Place the dripping pan in

position 1.

2. Place the rotisserie

support in position 3 and

insert the spit in the hole

provided on the back panel

of the oven.

3. Start the rotisserie

function by selecting the

or modes;

! When mode is on, the rotisserie will stop if the door

is opened.

Automatic cooking modes

! The temperature and cooking duration are pre-set values,

guaranteeing a perfect result every time - automatically. These

values are set using the C.O.P.® (Programmed Optimal

Cooking) system. The cooking cycle stops automatically and

the oven indicates when the dish is cooked. You may start

cooking whether the oven has been preheated or not.

The cooking duration can be customised according to

personal taste by modifying the relevant value - before

cooking begins - by ±5/20 minutes depending on the

selected programme. The duration can however be modied

even once cooking has begun. If the value is modied

before the programme begins, it is stored in the memory

and suggested again by the appliance when the programme

is next used. If the temperature inside the oven is higher

than the suggested value for the selected mode, the text

“Hot” appears on the TEMPERATURE display and it will

not be possible to begin cooking; wait for the oven to cool.

! When the cooking stage has been reached, the oven

buzzer sounds.

! Do not open the oven door as this will disrupt the cooking

time and temperature.

BEEF mode

Use this function to cook beef, pork and lamb. Place the

food inside the oven while it is still cold. The dish may also

be placed in a preheated oven.

FISH FILLETS mode

This function is ideal for cooking small-medium llets. Place

the food inside the oven while it is still cold.

BREAD mode

Use this function to bake bread. To obtain the best results, we

recommend that you carefully observe the instructions below:

• follow the recipe;

• do not exceed the maximum weight of the dripping pan;

• remember to pour 50 g (0,5 dl) of cold water into the

baking tray in position 5.

• The dough must be left to rise at room temperature for

1 – 1 ½ hours (depending on the room temperature) or

until the dough has doubled in size.

Recipe for BREAD:

1 Dripping pan holding 1000 g Max, lower level

2 Dripping pans each holding 1000 g Max, medium and

lower levels

Recipe for 1000 g of dough: 600 g our, 360 g water, 11g

salt, 25 g fresh yeast (or 2 sachets of powder yeast)

Method:

• Mix the our and salt in a large bowl.

• Dilute the yeast in lukewarm water (approximately 35

degrees).

• Make a small well in the mound of our.

• Pour in the water and yeast mixture.

• Knead the dough by stretching and folding it over itself

with the palm of your hand for 10 minutes until it has a

uniform consistency and is not too sticky.

• Form the dough into a ball shape, place it in a large bowl

and cover it with transparent plastic wrap to prevent the

surface of the dough from drying out. Select the manual

LOW TEMPERATURE function on the oven and set the

* Only available in certain models.

GB

25

temperature to 40°C. Place the bowl inside and leave

the dough to rise for approximately 1 hour (the dough

should double in volume).

• Cut the dough into equal sized loaves.

• Place them in the dripping pan, on a sheet of baking

paper.

• Dust the loaves with our.

• Make incisions on the loaves.

• Place the food inside the oven while it is still cold.

• Start the BREAD cooking mode.

• Once baked, leave the loaves on one of the grill racks

until they have cooled completely.

BAKED CAKES mode

This function is ideal for cooking desserts which are made

using natural yeast, baking powder and desserts which

contain no yeast. Place the dish in the oven while it is still

cold. The dish may also be placed in a preheated oven.

TARTS mode

This function is ideal for all tart recipes (which normally need

to be heated well from underneath). Place the food inside

the oven while it is still cold.

The dish may also be placed in a preheated oven.

Programming cooking

! A cooking mode must be selected before programming

can take place.

! Once a cooking mode has been selected, the button

is activated; it will then be possible to program a duration.

The button is only activated after a duration has been

set; it will then be possible to program a delayed start.

Programming the duration

1. Press the button; the button and the numbers on

the TIME display will ash.

2. Set the duration by pressing buttons “ ” and “ ”.

3. Once you have reached the desired duration, press the

button again.

4. Press the button to begin cooking.

5. When cooking has nished, “END” appears on the

TEMPERATURE display and a buzzer sounds.

• For example: it is 9:00 a.m. and a duration of 1 hour and

15 minutes is programmed. The programme will stop

automatically at 10:15 a.m.

Programming delayed cooking

! A cooking duration must be set before the cooking end

time can be scheduled.

! For the delayed programming to work properly, the clock

should be set to the correct time.

1. Press the button and repeat steps 1 to 3 as described

for the duration setting.

2. Then press the button and set the end time using

the “ ” and “ ” buttons.

3. Once you have reached the desired end time, press the

button again.

4. Press the button to activate the programmed mode.

The and buttons will ash alternately to indicate that

programming has taken place; in the time before cooking

starts, the TIME display will show the duration and the

cooking end time alternately.

5. Once cooking has finished, “END” appears on the

TEMPERATURE display and a buzzer sounds.

• For example: it is 9:00 a.m. and a time of 1 hour and 15

minutes is programmed, while the end time is set to 12:30.

The programme will start automatically at 11:15 a.m.

To cancel programming press the button.

Practical cooking advice

! Do not place racks in position 1 and 5 during fan-assisted

cooking. This is because excessive direct heat can burn

temperature sensitive foods.

! In the GRILL and FAN GRILLING cooking modes,

particularly when using the rotisserie spit, place the dripping

pan in position 1 to collect cooking residues (fat and/or

grease).

MULTILEVEL

• Use positions 2 and 4, placing the food which requires

more heat on 2.

• Place the dripping pan on the bottom and the rack on

top.

GRILL

• Place the rack in position 3 or 4. Position the food in the

centre of the rack.

• We recommend that the temperature is set to its

maximum level. The top heating element is regulated by

a thermostat and may not always operate constantly.

PIZZA

• Use a lightweight aluminium pizza pan. Place it on the

rack provided.

For a crispy crust, do not use the dripping pan as this

extends the total cooking duration and prevents the crust

from forming.

• If the pizza has a lot of toppings, we recommend adding

the mozzarella cheese to the top of the pizza halfway

through the cooking process.

26

GB

Modes Foods Weight

(in kg)

Preheating

Manual

Standard

guide

rails

Sliding

guide

rails

Multilevel*

1+1

1

2 and 4

1 and 2/3

2

1 or 2

2

2 and 4

1 and 3

1

1 and 3

yes

20-25

30-35

20-30

65-75

45-50

30-35

35-40

20-25

10-20

20-25

25-35

Grill*

1

0,7

0,5

0,8

0,7

n° 4 or 5

n° 4 or 6

1

4

3 or 4

4

-

3

2 or 3

3

-

no

300

10-20

10-15

15-20

10-20

10-12

3-5

70-80

Fan grilling*

1,5

1

1,5

1

2

-

2

-

2

no

210

200

210

55-60

30-35

70-80

60-70

60-75

70-80

40-45

Proving / Defrosting

White meringues

Meat / Fish

-

2

1

no

40

65

90

-

8-12 ore

90-180

Pizza*

Pizza

Focaccia bread

0,5

2

1

yes

15-20

20-25

Baking*

0,5

1

0,7

0,6

0,7

0,8

0,5

2 or 3

2 and 4

2 or 3

1 and 3

2

1 and 3

2

1 or 2

1 and 3

1 or 2

1 and 2

1

1 and 2

1

yes

180

180-190

160-170

180-190

180

200

90

210

25-35

40-50

45-55

20-25

35-40

20-30

20-25

30-35

180

20-25

Automatic**

Beef

Roast dishes12 or 32 no

Fish fillets

Cod

Perch

Trout

0,4-0,5

2 or 3

2

no

Bread***

Bread (see recipe)

11 or 21 no

Baked cakes

12 or 32 no

Tarts

0,52 or 32 no

Cooking advice table

Low

temperature*

Rack position Recommended

Temperature

(°C)

Cooking

duration

(minutes)

1 and 3 and 5

1 and 2 and 4

50 0,5

210-220

180

160-170

200-210

190-200

180

180-190

190

180

210

190-200

210-220

190-200

! ECO programme: This programme – which has longer cooking times but guarantees sensible energy saving – is recommended for dishes such as fish

fillets, small pastries and ve

g

etables. It is also suitable for warmin

g

foodstuffs and for completin

g

cookin

g

.

GB

27

Precautions and tips

! This appliance has been designed and manufactured

in compliance with international safety standards. The

following warnings are provided for safety reasons and

must be read carefully.

General safety

• The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

• When moving or positioning the appliance, always use

the handles provided on the sides of the oven.

• Do not touch the appliance while barefoot or with wet or

damp hands and feet.

• The appliance must be used by adults only for

the preparation of food, in accordance with the

instructions provided in this booklet. Any other

use of the appliance (e.g. for heating the room)

constitutes improper use and is dangerous. The

manufacturer may not be held responsible for any

damage caused as a result of improper, incorrect

and unreasonable use of the appliance.

• Do not touch the heating elements or certain parts

of the oven door when the appliance is in use; these

parts become extremely hot. Keep children well away

from the appliance.

• Make sure that the power supply cables of other electrical

appliances do not come into contact with the hot parts of

the oven.

• The ventilation and heat dispersal openings must never

be obstructed.

• Always grip the oven door handle in the centre: the ends

may be hot.

• Always use oven gloves when placing cookware in the

oven or when removing it.

• Do not use aluminium foil to line the bottom of the oven.

• Do not place ammable materials in the oven: if the

appliance is switched on accidentally, the materials could

catch re.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Do not perform any cleaning or maintenance work without

having disconnected the appliance from the electricity

mains.

• If the event of malfunctions, under no circumstances

should you attempt to perform the repairs yourself.

Contact an authorised Service Centre (see Assistance).

• Do not rest objects on the open oven door.

• Do not let children play with the appliance.

• The appliance should not be operated by people (including

children) with reduced physical, sensory or mental

capacities, by inexperienced individuals or by anyone

who is not familiar with the product. These individuals

should, at the very least, be supervised by someone who

assumes responsibility for their safety or receive preliminary

instructions relating to the operation of the appliance.

• The appliance is not intended to be operated by

means of an external timer or separate remote-

control system.

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment (WEEE), requires

that old household electrical appliances must not

be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you dispose

of the appliance it must be separately collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their

old appliance.

Respecting and conserving the environment

• You can help to reduce the peak load of the electricity

supply network companies by using the oven in the

hours between late afternoon and the early hours of

the morning. The cooking mode programming options,

the “delayed cooking” mode (see Cooking modes) and

“delayed automatic cleaning” mode (see Care and

Maintenance) in particular, enable the user to organise

their time efciently.

• Always keep the oven door closed when using the GRILL

and FAN GRILLING modes: this will achieve improved

results while saving energy (approximately 10%).

• Check the door seals regularly and wipe them clean

to ensure they are free of debris so that they adhere

properly to the door, thus avoiding the dispersal of heat.

! This product complies with the requirements of the latest

European Directive on the limitation of power consumption

of the standby mode.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before

carrying out any work on it.

Cleaning the appliance

• Slight differences in colour on the front of the oven are due

to the different materials used, i.e. glass, plastic or metal.

• Any shady areas resembling grooves on the oven door

glass are caused by reections from the oven light.

• The enamel is branded at very high temperatures. This

process may cause colour variations. This is normal and

will not affect appliance operation in any way. The thin

edges of the sheet metal cannot be entirely enamelled

and may therefore appear to be unnished. This will not

affect the rust protection.

• The stainless steel or enamel-coated external parts and

the rubber seals may be cleaned using a sponge that

has been soaked in lukewarm water and neutral soap.

Use specialised products for the removal of stubborn

stains. After cleaning, rinse and dry thoroughly. Do not

use abrasive powders or corrosive substances.

28

GB

• The inside of the oven should ideally be cleaned after

each use, while it is still lukewarm. Use hot water and

detergent, then rinse well and dry with a soft cloth. Do

not use abrasive products.

• All accessories - with the exception of the sliding racks

- can be washed like everyday crockery, and are even

dishwasher safe.

• We recommend that detergents are not sprayed directly

onto the control panel, but that a sponge is used instead.

! Never use steam cleaners or pressure cleaners on the

appliance.

Cleaning the oven door

! The door of LED INSIDE models cannot be removed.

Clean the glass part of the oven door using a sponge and

a non-abrasive cleaning product, then dry thoroughly with

a soft cloth. Do not use rough abrasive material or sharp

metal scrapers as these could scratch the surface and cause

the glass to crack.

For more thorough cleaning purposes, the oven door may

be removed:

1. Open the oven door fully (see diagram).

2. Use a screwdriver to lift up and turn the small levers F

located on the two hinges (see diagram).

F

3. Grip the door on the two outer

sides and close it approximately

half way. Pull the door towards you,

lifting it out of its slot (see diagram).

To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals

are damaged, please contact your nearest Service Centre

(see Assistance). We recommend that the oven is not used

until the seals have been replaced.

Replacing the light bulb

To replace the oven light

bulb:

1. Remove the glass cover

of the lamp-holder.

2. Remove the light bulb and

replace it with a similar one:

halogen lamp voltage 230 V,

wattage 25 W, cap G 9.

3. Replace the glass cover

(see diagram).

! Do not touch the light bulb directly with your hands.

! Do not use the oven lamp as/for ambient lighting.

Sliding rack kit assembly

To assemble the sliding

racks:

1. Remove the two frames,

lifting them away from the

spacers A (see gure).

2. Choose which shelf to use

with the sliding rack. Paying

attention to the direction in

which the sliding rack is to

be extracted, position joint B

and then joint C on the

frame.

3. Secure the two frames

with the guide rails using the

holes provided on the oven

walls (see diagram). The

holes for the left frame are

situated at the top, while the

holes for the right frame are

at the bottom.

4. Finally, t the frames on

the spacers A.

! Do not place the sliding racks in position 5.

Side and rear catalytic liners*

These are panels coated with a special enamel, which is

able to absorb the fat released by food as it cooks.

This enamel is quite strong, so that the various accessories

(racks, dripping pans, etc.) can slide along them without

damaging them. White marks may appear on the surfaces;

these are not a cause for concern.

Nevertheless, the following should be avoided:

- scraping the enamel with sharp objects (a knife, for

example);

- using detergents or abrasive materials.

A

B

C

Left

guide rail

Right guide

rail

Direction

of extraction

D

* Only available on certain models.

GB

29

Troubleshooting

Problem

Possible cause

Solution

The appliance has just been

connected to the electricity mains

or there has been a blackout.

Set the clock.

A programmed cooking mode

does not start.

There has been a blackout. Reprogram the cooking mode.

Only the high luminosity

“Clock button” is lit.

The appliance is in standby mode Press any button to exit

standby mode.

The temperature inside the oven

is higher than the suggested

value for the selected mode.

Wait for the oven to cool down.

Fan-assisted cooking has been

selected and the food looks burnt.

Positions 1 and 5: the direct

heat could cause

temperature-sensitive

foods to burn.

We recommend switching

dripping pan positions halfway

through cooking.

The “Clock button” and the

digits on the display flash.

An automatic mode has been

selected. “Hot” appears on the

display and cooking does not

start.

Page is loading ...

Hotpoint Ariston FK 103E P.20 X/HA S User guide

Hotpoint Ariston FK 103E P.20 X/HA S User guide

in other languages

Related papers