Whirlpool VRM 641 MD C User manual

Category
Hobs
Type
User manual
English
GB
Operating Instructions
HOB
Contents
Operating Instructions,1
Installation,2
Description of the appliance,5
Precautions and tips,6
Care and maintenance,7
Technical description of the models,7
FR
Français
Mode d’emploi Manutenção e cuidados
TABLE DE CUISSON
Sommaire
Mode d’emploi,1
Installation,8
Description de l’appareil, 11
Précautions et conseils, 12
Nettoyage et entretien,13
Description technique des modèles,13
Español
ES
Manual de instrucciones
ENCIMERA
Sumario
Manual de instrucciones,1
Instalación,14
Descripción del aparato,17
Precauciones y consejos,18
Mantenimiento y cuidados,19
Descripción técnica de los modelos,19
Instruções para a utilização
PLANO
Índice
Instruções para a utilização,1
Instalação, 20
Descrição do aparelho,23
Precauções e conselhos,24
Manutenção e cuidados,25
Descrição técnica dos modelos,25
PT
Português
DE
Bedienungsanleitung
KOCHFELD
Inhaltsverzeichnis
Bedienungsanleitung,1
Installation, 26
Beschreibung des Gerätes,29
Vorsichtsmaßregeln und Hinweise, 30
Reinigung und Pflege, 31
Technische Beschreibung der Modelle, 31
NL
PL
RS
Italiano
IT
Istruzioni per l’uso
PIANO COTTURA
Sommario
Istruzioni per l’uso,1
Installazione, 32
Descrizione dell’apparecchio,35
Precauzioni e consigli,36
Manutenzione e cura,37
Descrizione tecnica dei modelli,37
Deutsch
Nederland
Gebruiksaanwijzing
KOOKPLAAT
Inhoud
Gebruiksaanwijzing,1
Installatie, 38
Beschrijving van het apparaat,41
Voorzorgsmaatregelen en advies,42
Onderhoud en verzorging,43
Technische beschrijving van de modellen,43
Polski
Instrukcja obsługi
PŁYTA GRZEJNA
Spis treści
Instrukcja obsługi,1
Instalacja,44
Opis urządzenia,47
Zalecenia i środki ostrożności,48
Konserwacja i utrzymanie,49
Opis Techniczny,49
VEM 645 C
VRM 640 C
VRM 640 X
VRM 641 D C
VRM 641 D X
VRM 640
VRM 630 C
VRM 640 M IX
VRM 640 M C
VRM 641 MD IX
VRM 641 MD C
VRM 630 M C
Руководство по эксплуатации
ВАРОЧНАЯ ПАНЕЛЬ
Содержание
Руководство по эксплуатации,1
Монтаж,50
Описание изделия-Панель управления,53
Предосторожности и рекомендации,54
Техническое обслуживание и уход,55
Техническое обслуживание,56
Русский
2
GB
Installation
! Before operating your new appliance please read
this instruction booklet carefully. It contains important
information concerning the safe operation, installation
and maintenance of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to any new owners of the
appliance.
Positioning
! Keep all packaging material out of the reach of
children. It may present a choking or suffocation
hazard (see Precautions and tips).
! The appliance must be installed by a qualified
professional in accordance with the instructions
provided. Incorrect installation may cause harm to
people and animals or may damage property.
Built-in appliance
Use a suitable cabinet to ensure that the appliance
functions properly.
The supporting surface must be heat-resistant up to
a temperature of approximately 100°C.
If the appliance is to be installed above an oven,
the oven must be equipped with a forced ventilation
cooling system.
Avoid installing the hob above a dishwasher: if this
cannot be avoided, place a waterproof separation
device between the two appliances.
Depending on the hob you want to install, the
cabinet must have the following dimensions (see
gure):
560 +/- 1
490 +/- 1
48
590
520
560 +/- 1
490 +/- 1
48
574
504
Ventilation
To allow adequate ventilation and to avoid overheating of
the surrounding surfaces the hob should be positioned as
follows:
At a minimum distance of 40 mm from the back
panel.
So that a minimum distance of 20 mm is maintained
between the installation cavity and the cabinet
underneath.
Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 600 mm
from the edge of the hob.
FRONT SIDE
OF HOB
SUPPORTING
SURFACE
30
40
UNDERSIDE
OF HOB
5 mm
min. 20 mm
min. 20 mm
min. 40 mm
COMPARTMENT
5 mm
min. 40 mm
FAN-ASSISTED
OVEN
3
GB
Fixing
The appliance must be installed on a perfectly level
supporting surface.
Any deformities caused by improper fixing could affect
the features and operation of the hob.
The thickness of the supporting surface should be taken
into account when choosing the length of the screws for
the fixing hooks:
30 mm thick: 17.5 mm screws
40 mm thick: 7.5 mm screws
Fix the hob as follows:
1. Use short flat-bottomed screws to fix the 4 alignment
springs in the holes provided at the central point of
each side of the hob.
2. Place the hob in the cavity, make sure it is in a
central position and push down on the whole perimeter
until the hob is stuck to the supporting surface.
3. For hobs with raised sides: After inserting the hob
into its cavity, insert the 4 fixing hooks (each has its
own pin) into the lower edges of the hob, using the
long pointed screws to fix them in place, until the glass
is stuck to the supporting surface.
! The screws for the alignment springs must remain
accessible.
! In order to adhere to safety standards, the appliance
must not come into contact with electrical parts once it
has been installed.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a
tool.
Electrical connection
! The electrical connection for the hob and for any built-
in oven must be carried out separately, both for safety
purposes and to make extracting the oven easier.
Terminal board
On the lower part of the appliance there is a
connection box for the different types of electricity
supply (the picture is only
an indication and is not an
exact representation of the
purchased model).
Single-phase connection
The hob is equipped with a pre-connected electricity
supply cable, which is designed for single-phase
connection. Connect the wires in accordance with the
instructions given in the following table and diagrams:
Other types of connection
If the mains supply corresponds with one of the
following:
Voltage and mains frequency
• 400V - 2+N ~ 50/60 Hz
• 220-240V 3 ~ 50/60 Hz
• 400V - 2+2N ~ 50/60 Hz
Separate the wires and connect them in accordance
with the instructions given in the following table and
diagrams:
If the mains supply corresponds with one of the
following:
Voltage and mains frequency
• 400V 3 - N ~ 50/60 Hz
proceed as follows:
! The cable provided is not suitable for the following
types of installation.
1. Use a suitable supply cable, H05RR-F or higher, with
the right dimensions (cable cross section: 25 mm).
2. To open the terminal board, use a screwdriver as
a lever under the side tabs of the cover (see Terminal
board picture).
3. Loosen the cable clamp screw and the terminal
board screws in accordance with the type of
connection required and position the connection
supports as shown in the following table and diagrams.
4. Position the wires in accordance with the information
given in the following table and diagrams and connect
the appliance by tightening all the screws for the
springs as much as possible.
UNDERSIDE OF HOB
4
GB
5. Secure the power supply cable by fastening the
cable clamp screw, then put the cover back on.
Three-phase 400
Connecting the
electricity supply
cable to the mains
If the appliance is
being connected
directly to the
electricity mains an
omnipolar switch must be installed with a minimum
opening of 3 mm between contacts.
! The installer must ensure that the correct electrical
connection has been made and that it is fully compliant
with safety regulations.
Before connecting the appliance to the power supply,
make sure that:
The appliance is earthed and the plug is compliant
with the law.
The socket can withstand the maximum power of
the appliance, which is indicated on the data plate
located on the appliance itself.
The voltage falls within the range of values indicated
on the data plate.
The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only.
! The manufacturer declines any liability should
these safety measures not be observed.
! Do not remove or replace the power supply cable
for any reason. Its removal or replacement will void
the warranty and the CE marking. INDESIT does not
assume liability for accidents or damage arising from
replacement/removal of the original power supply
cable. Replacement can only be accepted when
carried out by personnel authorised by INDESIT and
using an original spare part.
5
1
2
3
4
U-bolt
connection support
Phase PhasePhase Neutral Earth
5
GB
Description of the
appliance
C
A
A
B
A
E
D
Switching on the glass ceramic hob
Traditional cooking zones
Traditional cooking zones (A) consist of circular heating
elements. They turn red approximately ten seconds after
they have been switched on.
Each cooking zone is fitted with a control knob (D) which
allows you to select from 12 different temperature settings
between a minimum of 1 and a maximum of 12.
Extendable cooking zones
The extendable radiant elements (B) are distinguished by
the fact that they have a double heating zone. You can
switch the smaller internal cooking zone on its own, or
both the external and internal zones.
The control knob (D) allows you to choose between two
power levels, which may both be adjusted between a
minimum value of 1 and a maximum of 12:
The lowest power level can be set by turning the knob
clockwise from 1 to 12.
Turn the knob completely round ( ), until you hear a
slight click, to enable the maximum power level. This in
turn can be adjusted to a value between 12 and 1 by
turning the knob anticlockwise. To restore the minimum
power level, turn the knob and set it back to position 0.
For double cooking zones, the first part of the knob
movement activates the smaller (internal) cooking zone.
To activate both (internal and external), it is necessary to
turn the knob completely ( ) and then select the desired
power level between 12 and 1.
Recommended power levels for various types of
cooking:
Operation indicator light (C)
This is illuminated when a heating zone has been
activated.
Set. Radiant Burner
0
Off
1
To melt butter and chocolate.
2
To heat liquids.
3
4
For creams and sauces.
5
6
For cooking at the boiling point.
7
8
For roasts.
9
10
For boiling large pieces of meat.
11
12
For frying.
For utilising both cooking areas.
Residual heat indicator light (E)
This indicates that one or more cooking zones are at a
temperature greater than 60°C, even after the cooking
zones have been switched off. Some models have 4
residual heat indicator lights, one for each cooking zone.
6
GB
Precautions and tips
! This appliance has been designed and manufactured in
compliance with international safety standards. The following
warnings are provided for safety reasons and must be read
carefully.
Practical advice on using the appliance
In addition, to obtain the best results from your hob:
Use pans with a thick, flat base in order to fully utilise the
cooking zone.
Always use pans with a diameter which is large enough
to cover the hotplate fully, in order to use all the available
heat.
Make sure that the base of the cookware is always clean
and dry, in order to fully utilise and extend the life of both
the cooking zones and the cookware.
Avoid using the same cookware which has been used
on gas burners: the heat concentration on gas burners
may distort the base of the pan, causing it not to adhere
correctly.
This appliance conforms to the following European
Economic Community directives:
- 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent
amendments;
-2004/108/EEC dated 15/12/04 (Electromagnetic
Compatibility) and subsequent amendments;
- 93/68/EEC dated 22/07/93 and subsequent amendments.
General safety
! Make sure that the air inlet behind the fan grille is never
obstructed. The built-in hob should, in fact, be provided
with suitable ventilation for the cooling of the electronic
components used in the appliance.
The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial use.
The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
Do not touch the appliance when barefoot or with wet or
damp hands and feet.
The appliance must be used by adults only for
the preparation of food, in accordance with the
instructions outlined in this booklet. Any other use of
the appliance (e.g. for heating the room) constitutes
improper use and is dangerous. The manufacturer
may not be held liable for any damage resulting from
improper, incorrect and unreasonable use of the
appliance.
Do not use the hob as a worktop or chopping board.
The glass ceramic hob is resistant to mechanical shocks, but
it may crack (or even break) if hit with a sharp object such
as a tool. If this happens, disconnect the appliance from the
electricity mains immediately and contact a Service Centre.
Ensure that power supply cables of other electrical
appliances do not come into contact with the hot parts of the
hob.
Remember that the cooking zones remain relatively hot for
at least thirty minutes after they have been switched off.
An indicator light provides a warning when residual heat is
present (see Start-up and use).
Keep any object which could melt away from the hob, for
example plastic and aluminium objects, or products with a
high sugar content. Be especially careful when using plastic
film and aluminium foil or packaging: if placed on surfaces
which are still hot, they may cause serious damage to the
hob.
Always make sure that pan handles are turned towards the
centre of the hob in order to avoid accidental burns.
When unplugging the appliance, always pull the plug from
the mains socket; do not pull on the cable.
Never perform any cleaning or maintenance work without
having disconnected the appliance from the electricity mains.
The appliance should not be operated by people (including
children) with reduced physical, sensory or mental
capacities, by inexperienced individuals or by anyone
who is not familiar with the product. These individuals
should, at the very least, be supervised by someone who
assumes responsibility for their safety or receive preliminary
instructions relating to the operation of the appliance.
Do not let children play with the appliance.
Do not look at the halogen lamps in the cooking zones for
long if they are present.
Disposal
When disposing of packaging material: observe local
legislation so that the packaging may be reused.
The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using
the normal solid urban waste cycle. Exhausted appliances
should be collected separately in order to optimise the cost
of re-using and recycling the materials inside the machine,
while preventing potential damage to the atmosphere and
to public health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations regarding
separated waste collection.
For further information relating to the correct disposal of
exhausted household appliances, owners may contact the
public service provided or their local dealer.
7
GB
Care and maintenance
Switching the appliance off
Disconnect your appliance from the electricity supply before
carrying out any work on it.
Cleaning the appliance
! Do not use abrasive or corrosive detergents (for example,
products in spray cans for cleaning barbecues and ovens),
stain removers, anti-rust products, powder detergents or
sponges with abrasive surfaces: these may scratch the
surface beyond repair.
! Never use steam cleaners or pressure cleaners on the
appliance.
It is usually sufficient simply to wash the hob using a damp
sponge and dry it with absorbent kitchen towel.
If the hob is particularly dirty, rub it with a special glass
ceramic cleaning product, then rinse well and dry
thoroughly.
To remove more stubborn dirt, use a suitable scraper.
Remove spills as soon as possible, without waiting for
the appliance to cool, to avoid residues forming crusty
deposits. You can achieve excellent results by using a
rust-proof steel wire sponge - specifically designed for
glass ceramic surfaces - soaked in soapy water.
If any plastic or sugary substances are accidentally
melted on the hob, remove them immediately with the
scraper, while the surface is still hot.
Once it is clean, the hob may be treated with a special
protective maintenance product: the invisible film left
by this product protects the surface from drips during
cooking. This maintenance task should be carried out
while the appliance is warm (not hot) or cold.
Always remember to rinse the appliance well with clean
water and dry it thoroughly: residues can become
encrusted during subsequent cooking processes.
Stainless steel frame (only in models with outer frame)
Stainless steel can be marked by hard water which has been
left on the surface for a long time, or by cleaning products
containing phosphorus.
After cleaning, it is advisable to rinse the surface well and dry
it thoroughly. If water is spilt on the surface, dry it quickly and
thoroughly.
! Some hobs have an aluminium frame which is similar to
stainless steel. Do not use any cleaning or degreasing
products which are not suitable for use with aluminium.
Disassembling the hob
If it is necessary to disassemble the hob:
1. Loosen the screws fixing the alignment springs on each
side.
2. Loosen the screws holding the fixing hooks in each corner.
3. Take the hob out of its installation cavity.
! Do not attempt to repair the appliance yourself. If the
appliance breaks down, contact a Service Centre.
Technical description of the models
This table provides a model-by-model list of the energy absorption values, type of heating elements and diameters of
each cooking zone.
Key:
H = single hilight
HD = double hilight
A = single halogen
VRM 641 D C
VRM 641 D X
VRM 641 MD IX
VRM 641 MD C
VEM 645 C
Power (W)
Diameter (mm)
Power (W)
Diameter (mm)
HD 2200/1000
210/140
A 2200
210
H 1400
160
H 1400
160
H 1200
145
H 1200
145
H 1800
180
H 1800
180
6600
6600
VRM 640 C
VRM 640 X
VRM 640
VRM 640 M IX
VRM 640 M C
VRM 630 C
VRM 630 M C
Power (W)
Diameter (mm)
Power (W)
Diameter (mm)
H 1800
180
H 2300
210
H 1400
160
H 1400
160
H 1200
145
H 1800
180
H 1800
180
6200
5500
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Whirlpool VRM 641 MD C User manual

Category
Hobs
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI