Rogue Photographic Design ROGUERELG2 User guide

Brand
Rogue Photographic Design
Model
ROGUERELG2
Category
Photo studio flash units
Type
User guide

Rogue Photographic Design ROGUERELG2

The Rogue Photographic Design ROGUERELG2 is a versatile lighting modifier that can be used to control and shape light from on-camera or off-camera flashes. It can be used to create a variety of lighting effects, including soft, diffused light, hard, directional light, or a combination of both. The ROGUERELG2 is made from a durable, lightweight material and features a unique, collapsible design that makes it easy to transport and store.

Here are some of the capabilities of the Rogue Photographic Design ROGUERELG2:

  • Controllable shape: The ROGUERELG2 has three adjustable rods that allow you to change its shape to direct light in different directions. This makes it possible to create a variety of lighting effects, from soft, diffused light to hard, directional light.

Rogue Photographic Design ROGUERELG2

The Rogue Photographic Design ROGUERELG2 is a versatile lighting modifier that can be used to control and shape light from on-camera or off-camera flashes. It can be used to create a variety of lighting effects, including soft, diffused light, hard, directional light, or a combination of both. The ROGUERELG2 is made from a durable, lightweight material and features a unique, collapsible design that makes it easy to transport and store.

Here are some of the capabilities of the Rogue Photographic Design ROGUERELG2:

  • Controllable shape: The ROGUERELG2 has three adjustable rods that allow you to change its shape to direct light in different directions. This makes it possible to create a variety of lighting effects, from soft, diffused light to hard, directional light.
Image © Frank Doorhof 2015
Image © Frank Doorhof 2015
Watch our Training Videos at RogueFlash.com
Instructions en ligne
Anleitung online
Instrucciones en línea
RogueFlash.com
QUICK START GUIDE
RogueFlash.com
RogueFlash.com
FlashBender Großer Reflektor
FlashBender Grand Réflecteur
Reflector FlashBender grande
10.5” x 11” (254mm x 288mm)
4.8 oz (135g)
FLASHBENDER LARGE REFLECTOR
FLASHBENDER LARGE REFLECTOR
2
Large Reflector
Small Reflector
FlashBender kleiner Reflektor
FlashBender petit réflecteur
Reflector FlashBender pequeño
10.5” x 7” (254mm x 178mm)
2.8 oz (78g)
FLASHBENDER SMALL REFLECTOR
FLASHBENDER SMALL REFLECTOR
2
FlashBender Large Reflector, Small Reflector
and Bounce Card each sold separately
Bounce Card
FlashBender formbare Reflektorkarte
FlashBender panneau réflecteur
Tarjeta de rebote FlashBender
5” x 9” (127mm x 228mm)
2.2 oz (62g)
FLASHBENDER BOUNCE CARD
FLASHBENDER BOUNCE CARD
2
®
®
New Lighting Videos
®
•
Lighting Techniques
•
Posing Tips
•
Product Demonstrations
Watch at RogueFlash.com
Reflectors
Large
Reflector
Large Refl ector Small Refl ector Bounce Card
The versatile FlashBender Large Refl ector is adaptable for use with on-
camera or off-camera fl ash. It can be used to control and shape your
main, background, hair, rim, or accent lights.
The smaller and lighter FlashBender Small Refl ector is ideally suited for on-
camera fl ash event photography. The Small Refl ector can also be used off-
camera to control and shape your main, background, hair, rim, or accent lights.
The Bounce Card is the smallest, lightest FlashBender and easily stows in
your pocket. When used with on-camera fl ash it creates a larger, softer light
source than a bare fl ash and allows directed bounce off ceilings or walls.
3. Shape Large Refl ector: Use the refl ector’s
positionable rods to manipulate its shape.
Adjust the light refl ected up, forward, or to the
sides by shaping the top or sides of the refl ector.
1. Lock Flash Head Up: Rotate the fl ash head into
its vertical, fully-locked position before attaching
the FlashBender. If the fl ash head will not lock in
the upright position, rotate the fl ash head 180˚ and
angle the fl ash forward.
Non-Locking Flash Heads: Rotate the fl ash head
180 degrees, then attach FlashBender. Use a tilter
or umbrella bracket to tilt the fl ash forward on light
stand.
2. Strap Refl ector to Flash:
Attach the FlashBender to
the fl ash by wrapping the
strap around the fl ash head.
Pull the blue strap through
one of the two buckle
positions and fasten the
hook-and-loop.
3. Shape Small Refl ector:
Use the refl ector’s positionable rods to
manipulate its shape. Adjust the light
refl ected up, forward, or to the sides by
shaping the top or sides of the refl ector.
1. Position Flash Head: Rotate the fl ash
head into its vertical position before
attaching the FlashBender.
4. Roll Refl ector Into a Snoot: Curve the
sides of the FlashBender refl ector into a tube.
Overlap the sides of the refl ector so that the
hook-and-loop strips on the opposite sides
connect. Direct the snooted fl ash to position
the spot of light.
4. Roll Refl ector Into a Snoot:
Curve the sides of the FlashBender
refl ector into a tube. Overlap the sides of
the refl ector so that the hook-and-loop
strips on the opposite sides connect.
Direct the snooted fl ash to position the
spot of light.
2. Strap Bounce Card
to Flash: Attach the
FlashBender to the fl ash by
wrapping the strap around
the fl ash head. Pull the blue
strap through one of the two
buckle positions and fasten
the hook-and-loop.
3. Shape Bounce Card:
Manipulate the Bounce Card’s
shape to adjust refl ected light
up or down.
1. Position Flash Head:
Rotate the fl ash head into its vertical position
before attaching the FlashBender.
smaller fl ashes use
fi rst buckle position
bigger fl ashes use
second buckle position
2. Strap Refl ector to Flash:
Attach FlashBender to the
fl ash by wrapping the strap
around the fl ash head. Pull
the blue strap through one of
the two buckle positions and
fasten the hook-and-loop.
smaller fl ashes use
fi rst buckle position
bigger fl ashes use
second buckle position
smaller fl ashes use
fi rst buckle position
bigger fl ashes use
second buckle position
© ExpoImaging, Inc., 2016
•
Patents: see www.ExpoIP.us
Rogue & FlashBender are registered trademarks of ExpoImaging, Inc.
For More Information, Visit RogueFlash.com
Note:
  • Page 1 1
  • Page 2 2

Rogue Photographic Design ROGUERELG2 User guide

Brand
Rogue Photographic Design
Model
ROGUERELG2
Category
Photo studio flash units
Type
User guide

Rogue Photographic Design ROGUERELG2

The Rogue Photographic Design ROGUERELG2 is a versatile lighting modifier that can be used to control and shape light from on-camera or off-camera flashes. It can be used to create a variety of lighting effects, including soft, diffused light, hard, directional light, or a combination of both. The ROGUERELG2 is made from a durable, lightweight material and features a unique, collapsible design that makes it easy to transport and store.

Here are some of the capabilities of the Rogue Photographic Design ROGUERELG2:

  • Controllable shape: The ROGUERELG2 has three adjustable rods that allow you to change its shape to direct light in different directions. This makes it possible to create a variety of lighting effects, from soft, diffused light to hard, directional light.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents