Feiss WB1449OBZ Installation guide

Feiss
Brand
Feiss
Model
WB1449OBZ
Type
Installation guide

Feiss WB1449OBZ is a versatile lighting fixture that can elevate the ambiance of any room. With its classic design and customizable features, it offers a range of lighting options to suit your needs. The fixture comes with crystal glass parts that add a touch of elegance and sparkle, allowing you to create a glamorous atmosphere. It supports candelabra-base bulbs of up to 60 watts, providing ample illumination.

Feiss WB1449OBZ is a versatile lighting fixture that can elevate the ambiance of any room. With its classic design and customizable features, it offers a range of lighting options to suit your needs. The fixture comes with crystal glass parts that add a touch of elegance and sparkle, allowing you to create a glamorous atmosphere. It supports candelabra-base bulbs of up to 60 watts, providing ample illumination.

IMPORTANT
TURN OFF THE POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX
BEFORE STARTING INSTALLATION
Carefully unpack and identify all parts before assembly. Bulb not
included.
1. Install mounting plate (see fig. 1):
A. Take supply wires from outlet box and carefully pass them through
center hole of mounting plate. Note: The flat surface of mounting
plate must face the outlet box.
B. Install mounting plate onto the outlet box using two screws
supplied with outlet box.
C. Spread electrical wires so that black wires are on one side of the
outlet box and the white wires are on the other side.
2. Connect electrical wires:
A. Connect white fixture wire with plastic insulation to white wire
from outlet box. Connect black fixture wire to black wire from
outlet box.
NOTE: Black outlet box wire may be red, round and smooth and/or
have copper conductor. White outlet box wire may be square and
ridged and/or have a silver conductor.
B. Connect fixture ground wire (without plastic insulation) to supply
ground wire (usually with green insulation) with wire connector.
Note: If there is no supply ground wire at outlet box then attach
fixture ground wire securely onto green grounding screw located at
mounting plate.
IMPORTANT: Never connect ground wire to black or white supply
wires (from outlet box).
3. Install fixture plate:
While carefully tucking all electrical wires inside of fixture plate,
install the fixture plate onto the mounting plate, fastening with set
screw from each side of fixture plate. Use provided hex key to
tighten.
4. A. Install crystal bobeche by slipping through sockets.
B. Install candle tube by slipping through sockets.
C. Install type-B, candelabra base, of 60 Watt maximum bulbs (not
included).
5. Hang all crystal glass parts as shown on drawing.
NOTE: To replace broken crystal or pin, extras are included in
hardware bag. Replace by gently bending open pin, remove broken
crystal or pin, hook new one, then close back pin. Avoid bending pin
into sharp angle.
Assembly Instructions For
WB1449
(E) 10/09
PIN
DESCRIPTION
Extra PIN
Qty.
3
2
1
Small S- Hook
x 2
Required
1
X1 X1X2
1
Extra
1
32
1
PIN PART
Bulb
(not included)
Set Screw
Supply Wire
Fixture Wire
Fixture Plate
Candle
Tube
Outlet Box
Mounting Plate
Outlet Box Screw
Crystal
Bobeche
  • Page 1 1

Feiss WB1449OBZ Installation guide

Feiss
Brand
Feiss
Model
WB1449OBZ
Type
Installation guide

Feiss WB1449OBZ is a versatile lighting fixture that can elevate the ambiance of any room. With its classic design and customizable features, it offers a range of lighting options to suit your needs. The fixture comes with crystal glass parts that add a touch of elegance and sparkle, allowing you to create a glamorous atmosphere. It supports candelabra-base bulbs of up to 60 watts, providing ample illumination.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents