Rust-Oleum 280104 User manual

Brand: Rust-Oleum

Model: 280104

Type: User manual

TECHNICAL DATA SPC-65

SPECIALTY

FARM & IMPLEMENT SPRAYS

Form: GDH-958

Rev.: 060217

.DESCRIPTION AND USES .

Rust-Oleum

Farm & Implement Sprays are a durable,

rust preventive enamel that is available in bright original

equipment colors. This Stops Rust

formula offers

excellent coverage, chip resistance and color retention.

Farm & Implement Sprays are ideal for tractors, farm

implements, lawn mowers, and more. Not for use on

galvanized metal.

.PRODUCTS .

SKU Description

280123 Gloss Black

280124 John Deere Green

280127 International Harvester Red

280129 John Deere yellow

280130 Low Gloss Black

280131 Ford Blue

280132 Gloss White

280133 Massey Ferguson Gray

280134 Massey Ferguson Red

280135 Allis Chalmers Orange

280136 Ford Red

280137 Red Oxide Metal Primer

280138 Ford Gray

280139 Oliver Green

280140 Caterpillar Yellow

280141 International Harvester White

280142 Kubota Orange

280143 New Holland Red

280144 New Holland Yellow

280145 Transport Yellow

280146 Gray Primer

. PRODUCT APPLICATION .

SURFACE PREPARATION

ALL SURFACES: Remove all dirt, grease, oil, salt and

chemical contaminants by washing the surface with a

commercial detergent, or other suitable cleaning method.

Mold and mildew must be cleaned with a chlorinated

cleaner or bleach solution. Rinse with fresh water and

allow to thoroughly dry.

STEEL: Scrape and wire brush or power tool clean to

remove loose rust, scale and deteriorated coatings. Use

7769 Rusty Metal Primer for sound rusted or clean metal

before application of a finish coat. 7780 Clean Metal

Primer is best for clean metal but may be used on sound

rusted metal as well.

PREVIOUSLY COATED: Previously coated surfaces must

be sound and in good condition. Smooth, hard, or glossy

finishes should be scarified by sanding to create a surface

profile.

.PRODUCT APPLICATION (cont.) .

SURFACE PREPARATION (cont.)

WARNING! If you scrape, sand or remove old paint from

any surface, you may release lead paint dust. LEAD IS

TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE

SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;

ESPECIALLY IN CHILDREN. PREGNANT WOMEN

SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH

approved respirator to control lead exposure. Clean up

carefully with a HEPA vacuum and a wet mop. Before you

start, find out how to protect yourself and your family by

contacting the National Lead Information Hotline at 1-800-

424-LEAD or log on to www.epa.gov/lead.

APPLICATION

Apply only when air and surface temperatures are

between 50-90°F (10-32°C) and the relative humidity is

below 85% to ensure proper drying. Protect the

surrounding area from overspray. Overspray can carry a

significant distance. Shake can vigorously for one minute

after the mixing ball begins to rattle. If mixing ball fails to

rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Hold

can upright 10-16" from surface and spray in a steady

back and forth motion, slightly overlapping each stroke.

Keep the can the same distance from the surface. Keep

the can in motion while spraying. Apply two or more light

coats a few minutes apart to avoid drips and runs. Do not

use near open flame.

DRY & RECOAT

Dry and recoat times are based on 70ºF (21°C) and 50%

relative humidity. Dries to the touch in 2-4 hours and can

be handled in 5-9 hours. Recoat within 1 hour or after 24

hours.

CLEAN-UP

Clean valve immediately after use by turning can upside

down and depressing spray button for 3-5 seconds (some

paint will be sprayed out, so be careful to not inadvertently

spray yourself or other objects). Clean up wet paint with

xylene or mineral spirits. Throw away empty can in trash

pick-up. Do not burn or place in home trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object

into can valve opening.

TECHNICAL DATA

FARM & IMPLEMENT SPRAYS

Rust-Oleum Corporation Form: GDH-958

11 Hawthorn Parkway Phone: 877-385-8155 Rev.: 060217

Vernon Hills, Illinois 60061 www.rustoleum.com

An RPM Company

.PHYSICAL PROPERTIES .

Physical Properties FARM & IMPLEMENT SPRAYS

Resin Type

Oil Modified Alkyd

Pigment Type

Varies with color

Solvents

Acetone, Ethyl Benzene, N-Butyl Acetate, Xylene

MIR

0.95 Max

Fill Weight

12 ounces

Practical Coverage at Recommended

DFT (assumes 15% material loss)

Approximately 6-7 sq.ft./can

(0.54-0.63 m

/can

Dry Times at 70-80ºF

(21-27ºC) and 50%

Relative Humidity

Touch

2-4 hours

Handle

5-9 hours

Recoat

Within 1 hour or after 24 hours

Dry Heat Resistance

200°F (93°C)

Shelf Life

5 years

Flash Point

-156°F (-104°C)

Safety Information

For additional information, see SDS

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The

statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use

of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,

will be limited to replacement of defective materials. All technical information is subject to change without notice.

Rust-Oleum 280104 User manual

Rust-Oleum 280104 User manual

Rust-Oleum 280104 User manual

Related papers

Other documents