Pulsar PSBEN10A12E - v1.1 Operating instructions

PSBEN 10A12E

v.1.1

PSBEN 13,8V/10A/65Ah/EN

Buffer, switch mode power supply unit.

EN**

Edition: 6 from 02.02.2015

Supercedes edition: 5 from 18.06.2014

LED Version

www.pulsar.pl PSBEN10A12E BLACK POWER

2

TABLE OF CONTENTS

1. PSU FEATURES. ................................................................................................................................................................... 4

2. FUNCTIONAL REQUIREMENTS OF THE PSU COMPLIANT WITH THE EN 50131-6 STANDARD. ................. 5

3. TECHNICAL DESCRIPTION. ............................................................................................................................................ 6

3.1 GENERAL DESCRIPTION. ....................................................................................................................................................... 6

3.2 BLOCK DIAGRAM. ................................................................................................................................................................ 7

3.3 DESCRIPTION OF PSU’S COMPONENTS AND CONNECTORS. .................................................................................................. 8

4. INSTALLATION. ................................................................................................................................................................ 10

4.1 REQUIREMENTS. ................................................................................................................................................................ 10

4.2 INSTALLATION PROCEDURE. .............................................................................................................................................. 10

5. FUNCTIONS......................................................................................................................................................................... 12

5.1 CONTROL PANEL. .............................................................................................................................................................. 12

5.2 MAIN MENU. ...................................................................................................................................................................... 13

5.2.1 Voltage indicator „Uo” ........................................................................................................................ 13

5.2.2 Output current indicator „Io” .............................................................................................................. 13

5.2.3 Failure history “FLh” ........................................................................................................................... 14

5.2.4 Current failures „FLc” ........................................................................................................................ 14

5.2.5 List of failure codes and information messages. ....................................................................................................... 15

5.3 PSU CONFIGURATION. ....................................................................................................................................................... 17

5.3.1 Battery test ON/OFF „tSt” .................................................................................................................... 18

5.3.2 LED Display Dimmer „dIS" .................................................................................................................. 19

5.3.3 Setting the communication address „Adr” applies to cooperation with PowerSecurity. ............... 19

5.3.4 Setting the transmission speed „trS” applies to cooperation with PowerSecurity. ...................... 20

5.3.5 Setting the parity of the transmission “trP” applies to cooperation with PowerSecurity. .............. 21

5.4 ACOUSTIC INDICATION. ..................................................................................................................................................... 21

5.5 TECHNICAL OUTPUTS. ........................................................................................................................................................ 22

5.6 INPUT OF COLLECTIVE FAILURE EXT IN. ........................................................................................................................... 22

5.7 ENCLOSURE TAMPER INDICATION - TAMPER. ................................................................................................................. 23

5.8 OVERVOLTAGE PROTECTION OF THE PSU OUTPUT OVP. ................................................................................................... 24

5.9 PSU OVERLOAD. ................................................................................................................................................................ 24

6 RESERVE POWER SUPPLY CIRCUIT. .......................................................................................................................... 25

6.1 RUNNING THE PSU FROM THE BATTERY. ........................................................................................................................... 25

6.2 DEEP DISCHARGE BATTERY PROTECTION UVP. ................................................................................................................. 25

6.3 BATTERY TEST. .................................................................................................................................................................. 25

6.4 STANDBY TIME. ................................................................................................................................................................. 26

6.5 BATTERY CHARGING TIME. ................................................................................................................................................ 26

6.6 OPERATION WITHOUT A BATTERY. ..................................................................................................................................... 26

7. REMOTE MONITORING (OPTIONS: WI-FI, ETHERNET, RS485, USB). ................................................................ 27

7.1 COMMUNICATION VIA THE USB-TTL INTERFACE. ............................................................................................................ 27

7.2 ETHERNET NETWORK COMMUNICATION. ........................................................................................................................ 27

7.3 THE WI-FI WIRELESS COMMUNICATION. ............................................................................................................................ 28

7.4 RS485 NETWORK COMMUNICATION. ................................................................................................................................. 29

7.5 „POWERSECURITY” PROGRAM. .......................................................................................................................................... 30

www.pulsar.pl PSBEN10A12E BLACK POWER

3

8. TECHNICAL PARAMETERS. .......................................................................................................................................... 31

TABLE 13. ELECTRICAL PARAMETERS. ...................................................................................................................................... 31

TABLE 14. MECHANICAL PARAMETERS. .................................................................................................................................... 32

TABLE 15. SAFETY OF USE. ....................................................................................................................................................... 32

9. TECHNICAL INSPECTIONS AND MAINTENANCE. .................................................................................................. 33

www.pulsar.pl PSBEN10A12E BLACK POWER

4

1. PSU features.

 EN50131-6 compliance, 1÷3 grades and II

environmental class

 mains supply of 230VAC

 uninterrupted voltage of 13,8VDC

 fitting battery: 65Ah/12V

 high efficiency 80%

 PSU current efficiency:

 5,41A – for grades 1 , 2 *

 2,16A – for grades 3 **

 10A – for general use ***

(see: chapter 3.1)

 low level of voltage ripple

 microprocessor-based automation system

 intelligent management of PSU’s output power level

 ‘SERIAL’ communication port with implemented

MODBUS RTU protocol

 remote monitoring (option: Wi-Fi, Ethernet, RS485,

USB)

 free program - ‘PowerSecurity’ for monitoring the PSU

operation parameters

 load current control

 output voltage control

 output fuse status control

 dynamic battery test

 battery circuit continuity control

 battery voltages control

 battery fuse status control

 battery charge and maintenance control

 deep discharge battery protection (UVP)

 battery overcharge protection

 battery output protection against short circuit and

reverse polarity connection

 jumper selectable battery charging current

0,6A/1,5A/2,2A/3A

 remote battery test (additional module required)

 START button for battery activation

 STOP button for disconnecting during battery-assisted

operation

 optical indication – LED panel

 output current readings

 output voltage readings

 failure codes with history

 optical indication of PSU overload OVL

 acoustic indication of failure

 adjustable times indicating AC power failure

 technical inputs/outputs with galvanic isolation

 EXT IN input of collective failure

 EPS technical output indicating AC power loss

 PSU technical output indicating PSU failure

 APS technical output indicating battery failure

 internal memory of PSU operating status

 protections:

 SCP short circuit protection

 OLP overload protection

 OHP overheat protection

 OVP over voltage protection

 surge protection

 against tampering: unwanted opening of the

enclosure or detachment from the mounting surface

 convectional cooling

 warranty – 5 year from the production date

www.pulsar.pl PSBEN10A12E BLACK POWER

5

2. Functional requirements of the PSU compliant with the EN 50131-6

standard.

Functional requirements

Requirements of

EN 50131-6

PSBEN10A12E

Grade 1

Grade 2

Grade 3

EPS network absence

YES

Low battery voltage

YES

Protection against complete battery

discharge

-

YES

Battery failure

-

YES

No battery charge

-

YES

Low output voltage

-

YES

High output voltage

-

YES

PSU failure

-

YES

Surge protection

-

YES

Short circuit protection

YES

Overload protection

YES

Output fuse activation

-

YES

Battery fuse failure

-

YES

EPS technical output

YES

APS technical output

YES

PSU technical output

YES

Input of collective failure

-

YES

Remote battery test

-

YES

Tamper indicating enclosure opening

YES

Tamper indicating detachment from the

mounting surface

-

YES

www.pulsar.pl PSBEN10A12E BLACK POWER

6

3. Technical description.

3.1 General description.

The buffer power supply is designed in accordance with the requirements of the EN 50131-6 standard,

grade 1÷3 and II environmental class. It is intended for an uninterrupted supply of alarm system devices requiring

stabilized voltage of 12V DC (+/-15%).

Depending on a required protection level of the alarm system in the installation place, the PSU efficiency

and the battery charging current should be set as follows:

* Grade 1, 2 - standby time 12h

Output current 5,41A + 3A battery charge

** Grade 3 - standby time 30h if the faults of the main power source are reported to the Alarm Receiving

Centre - ARC (in accordance with 9.2 – EN 50131-1 standard).

Output current 2,16A + 3A battery charge

- standby time 60h if the faults of the main power source are reported to the Alarm Receiving

Centre - ARC (in accordance with 9.2 – EN 50131-1 standard).

Output current 1,08A + 3A battery charge

*** General use – if the PSU is not mounted in an installation complaint with the EN-50131 standard, the

acceptable current efficiency amounts to:

1. Output current 10A + 0,6A battery charge

2. Output current 9,1A + 1,5A battery charge

3. Output current 8,4A + 2,2A battery charge

4. Output current 7,6A + 3A battery charge

Total current of the receivers + battery: 10,6A max.

In case of power decay, a battery back-up is activated immediately. The PSU is housed in a metal

enclosure (color: RAL 9005 - black) with battery space for a 65Ah/12V battery. It is fitted with micro switches

indicating unwanted door opening (front panel) and detachment from the mounting surface.

DOPTIONAL POWER SUPPLY CONFIGURATIONS:

(visualization available at www.pulsar.pl)

1. Buffer power supply PSBEN 13,8V/8x1A/65Ah/INTERFACE

- PSBEN 10A12E + LB8 8x1A(AWZ579,AWZ580)+65Ah+INTERFACE

2. Buffer power supply PSBEN 13,8V/2x12V/2x5A/65Ah

- PSBEN 10A12E + 2xRN500(13,8V/12V)+65Ah

www.pulsar.pl PSBEN10A12E BLACK POWER

7

3.2 Block diagram.

The PSU is manufactured based on a high-duty system of DC/DC converter. The microprocessor system is

responsible for full diagnostics of the PSU and battery parameters.

Fig. 1. Block diagram of the PSU.

www.pulsar.pl PSBEN10A12E BLACK POWER

8

3.3 Description of PSU’s components and connectors.

Table 1. Elements of the PSU pcb (see Fig. 2).

Element

no.

Description

PANEL – optical indication connector

P

BAT

; pin - configuration of battery protection UVP

 P

BAT

= battery protection (disconnection) off

 P

BAT

= battery protection (disconnection) on

T

AC

; pins J1, J2 - adjustable time lag of AC power failure indication

 J1= , J2= time lag T= 5s

 J1= , J2= time lag T= 140s

 J1= , J2= time lag T= 17m

 J1= , J2= time lag T= 2h 20m

Caption: jumper on, jumper off

Operation without battery Disabling the time-based lock of the test.

(section 6.6) (section 6.3)

I

BAT

– pin; battery charging current selection

J1= , J2= J3= I

BAT

=0,6 A

J1= , J2= J3= I

BAT

=1,5 A

J1= , J2= J3= I

BAT

=2,2 A

J1= , J2= , J3= I

BAT

=3 A

Caption: jumper on, jumper off

START – button (launching the PSU from a battery)

STOP – button (disconnection of the PSU during battery-assisted operation)

– pin; activation of the acoustic indication

- indication on

- indication off Caption: jumper on, jumper off

V

ADJ

– potentiometer, DC voltage adjustment

BUZZER – acoustic indicator

F

BAT

– fuse in the battery circuit

Connectors:

~AC~ – AC power input

+BAT – DC power battery output

+AUX – DC power output (+AUX= +U, -AUX=GND)

EPS FLT – technical output of AC network absence indication

open = AC power failure

close = AC power - O.K.

PSU FLT – technical output of PSU failure

open = failure

close = PSU working correctly - O.K.

APS FLT – technical output of battery failure

open = battery failure

close = battery O.K.

EXT IN – input of collective failure

V

EXT

pin – polarization of EXT IN circuit

Communication connector

LEDs – optical indication:

AC – presence of the AC power

AUX – DC output voltage

OVL – PSU overload

PSU – PSU failure

APS – battery failure

EXT – EXT IN input’s status

LB – battery charge

OVP – optical indication for activating the over voltage system

TAMPER – connector for the micro switch tamper

www.pulsar.pl PSBEN10A12E BLACK POWER

9

Fig. 2. The view of the PSU’s PCB.

Table 2. PSU elements (see fig. 3).

Element no.

Description

Insolation transformer

PSU board (see Tab.1, fig.2)

TAMPER; micro-switch (contacts) of tamper resistance (NC)

F

MAINS

fuse in the supply circuit (230V/AC)

L-N power supply connector 230V/AC, PE protective connector

Battery connectors: positive: +BAT = red, negative: - BAT = black

Tamper grip

Fig.3. The view of the PSU.

www.pulsar.pl PSBEN10A12E BLACK POWER

10

4. Installation.

4.1 Requirements.

The PSU is to be mounted by a qualified installer, holding relevant permits and licenses (applicable and

required for a given country) for 230V/AC in and low-voltage installations.

As the power supply is designed for a continuous operation and is not equipped with a power-

switch, therefore, an appropriate overload protection in the power supply circuit should be provided. Moreover, the

user should be informed how to disconnect the power supply unit from the mains supply (usually by assigning an

appropriate fuse in the fuse box). The electrical system shall be made in accordance with applicable standards

and regulations. The power supply should operate in a vertical position in order to provide free and

convectional air flow through ventilating holes of the casing.

4.2 Installation procedure.

CAUTION!

Before installation, cut off the voltage in the 230V power-supply circuit.

To switch off power use an external switch in which the distance between the contacts of all poles in the

disconnection state is not less than 3mm.

1. Mount the PSU in a selected location. It is particularly important to bolt the tamper grip to the mounting surface.

The grip is located in the central part of the enclosure (see fig. 3 [7]) and guarantees indication in case of any

attempts of detaching the device from the mounting surface. Proper installation is one of the requirements of the

EN 50131-6 standard.

Fig. 4. Fixing a tamper grip.

2. Connect the power cables (~230VAC) to L-N terminals of the PSU. Connect the ground wire to the terminal

marked by the earth symbol: PE. Use a three-core cable (with a yellow and green PE protection wire) to make the

connection. Lead the cables to the appropriate terminals through the insulating bushing.

The shock protection circuit shall be performed with a particular care, i.e. the yellow and green wire coat

of the power cable shall stick to one side of the terminal - marked with the PE symbol on the PSU

enclosure. Operation of the PSU without the properly made and fully operational shock protection circuit

is UNACCEPTABLE! It can cause a device failure or an electric shock.

3. Connect the receivers’ cables to the +AUX, -AUX connectors of the terminal block on the PSU board.

4. If necessary, connect the device’s leads to the technical inputs and outputs:

- EPS FLT; technical output of AC power loss indication (alarm panel, controller, indicator, etc.)

- PSU FLT; technical output of the PSU failure.

- APS FLT; technical output of the battery failure.

- TAMPER; output indicating enclosure opening or detachment from the assembly surface.

- EXT IN; input of collective failure.

5. With the I

BAT

jumper determine the maximum battery charging current, in accordance with the battery

parameters.

6. With the P

BAT

jumper determine if the discharged battery disconnection system U<10V (+/-5%) shall be on or off.

The battery protection is on when the P

BAT

jumper is off.

7. Switch on the ~230V AC supply (red AC diode and green AUX diode should be on).

8. Check the output voltage (the PSU voltage without load and without battery should amount to 13.7V ÷ 13.9V,

with a battery or during battery charging process: 11.0V÷13.8V). If the value of the voltage requires adjustment, it

www.pulsar.pl PSBEN10A12E BLACK POWER

11

should be set with use of the V

ADJ

potentiometer, monitoring the voltage at the AUX output of the PSU.

9. Connect the batteries in accordance with the markings: +BAT red to 'plus', -BAT black to 'minus’. The LB diode

should be on during battery charging process.

10. Press the STOP button to activate or deactivate a dynamic battery test. Deactivating the test turns out the PSU

failure indication at the APS FLT output, but it does not affect the protection system against complete battery

discharge.

11. Check the current consumption of the receivers, taking into account the battery charging current, so as not to

exceed the total current efficiency of the PSU.

12. Once the tests are completed, close the PSU cover.

Table 3. Operation parameters.

Environmental class

II

Operating temperature

-10ºC...+40ºC

Storing temperature

-20ºC...+60ºC

Relative humidity

20%...90%, no condensation

Sinusoidal vibrations during operation

EN 50130-5

Surges during operation

EN 50130-5

Direct insolation

unacceptable

Vibrations and surges during transport

PN-83/T-42106

Table 4. Factory settings of the PSU.

Indication time of EPS network loss

5s

section 5.5

Battery charging current

1,5A

section 6.5

Battery presence

YES (battery present)

section 6.6

Battery test

ON

section 5.3.1

section 6.3

Deep discharge battery protection UVP

ON

section 6.2

Acoustic indication

ON

section 5.4

LED display dimmer

OFF

section 5.3.2

Communication address

1

section 5.3.3

Transmission

115.2k 8E1

section 5.3.4

section 5.3.5

www.pulsar.pl PSBEN10A12E BLACK POWER

12

5. Functions.

5.1 Control Panel.

The PSU features a panel with buttons and LED display, enabling reading of all the available electrical

parameters. The panel buttons are used to select and confirm the parameters, which should be displayed.

Fig. 5. Control panel.

Table 5. The description of the buttons and LEDs of the LED panel.

Description

Additional

information

- moves the pointer on the screen

- next screen selection

- selection approval

- red LED – indicating 230V AC voltage

- red LED – indicating power supply overload

section 5.9

- red LED – indicating PSU failure

section 5.2.5

- red LED – indicating battery failure

- green LED – indicating power at the AUX output of the PSU

- three yellow LEDs indicating approximate battery charge level

www.pulsar.pl PSBEN10A12E BLACK POWER

13

5.2 Main menu.

The PSU is equipped with a menu, which allows to preview the current electrical parameters. The diagram

explaining the menu structure is presented below.

Fig. 6. The menu of the display.

Table 6. The description of display symbols.

Symbol

Description

Additional information

AUX output voltage [V]

Factory setting 13,8V

Output current [A]

Failure history

Section 5.2.3

Current failures

Section 5.2.4

5.2.1 Voltage indicator „Uo”

The voltage indicator displays the measured output voltage at the AUX output. If the voltage drops below

13V (during operation with activated battery test) or exceeds 14.7V, the PSU will indicate a failure.

The resolution of voltage measurement is 0.1V and should be treated with caution. If a greater accuracy is

required, use a multimeter.

5.2.2 Output current indicator „Io”

The output current indicator displays the measured output current drawn from the AUX output.

If the current value is exceeded, the power supply unit will indicate failure.

The resolution of current measurement is 0.1A and should be treated with caution. If a greater accuracy is

required, use a multimeter.

www.pulsar.pl PSBEN10A12E BLACK POWER

14

5.2.3 Failure history “FLh”

The PSU stores 30 last failures in non-volatile memory, which can be reviewed later.

In order to review the failures, use the "<" or ">" button to set the FLh parameter and confirm by pressing "OK".

The display will show the number of failure in the memory and its code. Pressing the "OK" button again will display

the next failure in the memory.

The memory of the new power supply remembers the events that are the result of the efficiency tests

carried out at the production stage.

- press „<” or „>” button to set the „FLh” parameter on the display

- press „OK” button

- number 1, indicating the number of failure in the memory (the highest priority),

will be displayed. Then, after one second, failure code will be automatically displayed

- press „OK” button

- the number 2, denoting the next number of failure in the memory, will be displayed.

Then, after one second, the next failure code will be automatically displayed.

- if the memory has more failures, pressing the "OK" button will result

in displaying subsequent codes

- the „- - -„ parameter on the display marks the end of the list of failures

5.2.4 Current failures „FLc”

In case of abnormal electrical parameters, the power supply provides optical and acoustic indication of the

failure via corresponding LED and a beeper (if not disabled).

The PSU can simultaneously indicate several failures. Thanks to this solution, codes of all failures and their

priority can be previewed in the FLc menu. In the FLc menu, each press of the "OK" button on the panel displays

the next error code that caused the failure. If there are multiple failures at the same time, pressing the "OK" button

will display the next code. The display order of failures is arranged by priority of importance. The first failures in the

display order are of the highest priority.

Section 5.2.5 summarizes all the failure codes that may occur during the power supply operation. The

individual codes are accompanied by appropriate optical indication on the panel, acoustic indication and activation

of the dedicated technical output.

www.pulsar.pl PSBEN10A12E BLACK POWER

15

- press „<” or „>” button to set the „FLc” parameter on the display „FLc”

- press „OK” button

- the number 1, indicating the number of failure in the memory (the highest priority),

will be displayed. Then, after one second, failure code will be automatically displayed

- press „OK” button

- the number 2, denoting the next number of failure in the memory, will be displayed.

Then, after one second, the next failure code will be automatically displayed.

- if the memory has more failures, pressing the "OK" button will result in displaying

subsequent codes

- the „- - -„ parameter on the display marks the end of the list of failures

5.2.5 List of failure codes and information messages.

The PSU indicates the operation status with the appropriate code. The codes are divided into two

groups,marked with the initial letters "F" or "I”.

The codes beginning with the letter "F" indicate a failure. The codes that begin with the letter "I" indicate the

correct operation of the PSU or repaired fault, involving, for example, fuse replacement: "I03 - BAT fuse replaced”.

www.pulsar.pl PSBEN10A12E BLACK POWER

16

Table 7. List of PSU failure codes.

Failure

code

Information

Technical

output

activation

Additional information

Additional

information

F01

AC power fail!

EPS FLT

- No AC mains supply

- F

MAINS

fuse failure

F02

AUX fuse fail!

PSU FLT

- Blown F

AUX

fuse

- AUX output overload

F03

BAT fuse fail!

APS FLT

- Blown F

BAT

fuse

- Short circuit in the battery circuit

- Short circuit in the AUX output circuit

F04

Output overload!

PSU FLT

- PSU overload

Section 5.9

F05

Battery fail!

APS FLT

- Worn out battery

- Undercharged battery

- Battery not connected

Section 5.5

Section 6

F06

High AUX voltage!

PSU FLT

- Output voltage over 14.7V

F07

High battery voltage!

PSU FLT

- Battery voltage >14V

F08

Charge circuit fail!

PSU FLT

- The output voltage of the PSU set too low ,

below 13V

- Battery charging circuit failure

F09

Low AUX voltage!

PSU FLT

- Output voltage below 11,8V

(during buffer operation)

F10

Low battery voltage!

APS FLT

- the battery voltage has dropped below

11,5V (during battery-assisted operation)

F11

Low battery volt. –

off!

APS FLT

- the battery voltage has dropped below 10V

(during battery-assisted operation)

F12

External input EXTi!

- Activation of the input of collective failure

EXT IN

Section 5.6

F13

PSU cover opened!

PSU FLT

F50-F54

Internal supply fail!

PSU FLT

- service codes

F60

No communication

PSU FLT

- no communication with LCD panel

F61-F64

Control panel fail

PSU FLT

- service codes

F65

Access unlocked

- passwords unlocked

Table 8. List of PSU message codes.

Message

code

Description

I00

Power supply start-up

I01

AC power back

I02

AUX fuse replaced

I03

BAT fuse replaced

I04

Battery OK

I05

Battery test – START

I06

PSU cover closed

Table 9. Optical indication of failure with the PSU LED on the PCB of the PSU.

The number of

flashes of the PSU

LED on the PCB of

the power supply

Failure

code

Failure description

1

F06

High AUX voltage!

2

F07

High battery voltage!

3

F08

Charge circuit fail!

4

F09

Low AUX voltage!

5

F50-F54

F60

Internal supply fail!

No communication

6

F13

PSU cover opened!

www.pulsar.pl PSBEN10A12E BLACK POWER

17

5.3 PSU configuration.

The PSU is equipped with a configuration menu that allows to configure the settings by changing or the

activation of some of its parameters. The figure illustrating the configuration menu structure is shown below.

Fig. 7. The PSU configuration menu.

Table 10. Description of symbols.

Symbol

Description

Additional

information

Battery test – „tSt”

On – battery test on

OFF – battery test off

Sections 5.3.1

LED display dimmer

On – dimmer ON

OFF – dimmer OFF

Sections 5.3.2

Communication address – „Adr”

1÷ 247 power supply address required at

the time of communication with the computer

1 – factory setting

Sections 5.3.3

Transmission – „trS”

Determines the speed of communication

9.6k

:

115.2k (factory setting)

Sections 5.3.4

Parity of the transmission – „trP”

Determines the method of communication

8N2

8E1 (factory setting)

8O1

Sections 5.3.5

www.pulsar.pl PSBEN10A12E BLACK POWER

18

5.3.1 Battery test ON/OFF „tSt”

The "tSt" function allows to enable or disable the test of the battery (Section 6.3) connected to the power

supply. When activated, the battery test occurs automatically if it is not blocked by the control system (section 6.3).

- simultaneously press the „<,>” rightmost and leftmost buttons on the LED panel

- the „tSt” parameter will be displayed

- press „OK”

- the current settings will be displayed

- use the „<” or „>” buttons to in order to set the status

On – battery test on

OFF – battery test off

- approve your choice with the ‘OK’ button

- in order to return to the main menu, simultaneously press the „<,>” rightmost

and leftmost buttons on the LED panel

Deactivating/activating the test with the STOP button on the PCB of the PSU.

During mains-powered PSU operation press the STOP button on the main board and hold it for 3 seconds.

The device will confirm the activation/deactivation:

 testing off – the tOF sign appears on the display , single beep

 testing on – the tOn sign appears on the display , double beep

Deactivating/activating the test is stored in the memory even after unplugging the device from

mains. The battery failure indication at the APS FLT output is automatically switched off. The

battery protection system against deep discharged remains on, though.

www.pulsar.pl PSBEN10A12E BLACK POWER

19

5.3.2 LED Display Dimmer „dIS"

LED display dimmer allows to dim the display if no buttons are pressed within 5 minutes.If the display is

in the blackout mode, pressing any button will "reactivate" the display.

- simultaneously press the „<,>” rightmost and leftmost buttons on the LED panel

- the „tSt” parameter will be displayed

- use the „<” or „>” buttons to display the „dIS” parameter

- press „OK”

- the current status will be displayed

- use the „<” or „>” buttons in order to set the status

On – dimmer on

OFF – dimmer off

- confirm by pressing „OK”

- in order to return to the main menu, simultaneously press the „<,>” rightmost

and leftmost buttons

5.3.3 Setting the communication address „Adr” applies to cooperation with PowerSecurity.

All power supplies are factory-set to address 1.

All the parameters responsible for communication between the PSU and the computer, namely the

address, parity and speed should have the same settings for both the PSU and the PowerSecurity program.

Communication address allows to identify power supply units in the same communication network.

- simultaneously press the „<,>” rightmost and leftmost buttons

- the „tSt” parameter will be displayed

- use the „<” or „>” buttons to display the „Adr” parameter

www.pulsar.pl PSBEN10A12E BLACK POWER

20

- press „OK”

- the current address of the PSU will be displayed

- use the „<” or „>” buttons in order to set the address

1÷ 247 – address of the PSU during the communication with the computer

- confirm by pressing „OK”

- in order to return to the main menu, simultaneously press the „<,>” rightmost

and leftmost buttons

5.3.4 Setting the transmission speed „trS” applies to cooperation with PowerSecurity.

All the parameters responsible for communication between the PSU and the computer, namely the

address, parity and speed should have the same settings for both the PSU and the PowerSecurity program.

The PSU has preset transmission parameters of 115200 baud 8E1. However, if it is connected to the

network with differently defined parameters, make the appropriate changes to its configuration.

- simultaneously press the „<,>” rightmost and leftmost buttons

- the „tSt” parameter will be displayed

- use the „<” or „>” buttons to display the „trS” parameter

- press „OK”

- the information about the transmission speed will be displayed

- use the „<” or „>” buttons in order to set the required transmission speed,

- 9.6k

:

- 115.2k (factory setting)

- confirm by pressing „OK”

- in order to return to the main menu, simultaneously press the „<,>” rightmost

and leftmost buttons

Page is loading ...

Pulsar PSBEN10A12E - v1.1 Operating instructions

Pulsar PSBEN10A12E - v1.1 Operating instructions

Related papers

Other documents