Zanussi ZJB9476X is an appliance with two compartments: freezer and refrigerator. The freezer compartment, which has a capacity of 93 litres, is equipped with the Fast Freeze function. This function, which should be activated at least 24 hours before freezing fresh food, helps to maintain the quality of the food by quickly freezing it. The refrigerator compartment, with a capacity of 226 litres, is equipped with Dynamic Air Cooling, which ensures an even temperature distribution throughout the compartment.
Zanussi ZJB9476X is an appliance with two compartments: freezer and refrigerator. The freezer compartment, which has a capacity of 93 litres, is equipped with the Fast Freeze function. This function, which should be activated at least 24 hours before freezing fresh food, helps to maintain the quality of the food by quickly freezing it. The refrigerator compartment, with a capacity of 226 litres, is equipped with Dynamic Air Cooling, which ensures an even temperature distribution throughout the compartment.
FRIDGE-FREEZER
ZJB 9476 X
INSTRUCTION BOOKLET
2223 214-75
2
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is left with the appliance in order that the new owner
can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of safety.You MUST read it carefully before installing
or using the appliance.
Installation
• This appliance is heavy. Care should be taken when
moving it.
• It is dangerous to alter the specifications or attempt
to modify this product in any way.
• Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cable is damaged, it must
be replaced by a special cable available from your
local Service Force Centre.
• Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
• Parts which heat up should not be exposed.
The back of the appliance should be close to a solid
wall but leaving the required distance for ventilation
as stated in the installation instructions.
• The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Child Safety
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
• Keep all packaging well away from children.
General Safety
• This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging must
therefore only be carried out by authorised
technicians.
• Take utmost care when handling your appliance
so as not to cause any damages to the cooling
unit with consequent possible fluid leakages.
• The appliance must not be located close to
cookers, radiators or boilers.
• Avoid prolonged exposure of the appliance to
direct sunlight.
• Do not use other electrical appliances (such as
ice cream makers) inside of refrigerating
appliances.
During Use
• This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs.
• Frozen food must NOT be re-frozen once it has
thawed out.
• Do not place carbonated or fizzy drinks in the
freezer.
• Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
• Ice lollies can cause ‘frost/freezer burns’ if
consumed straight from the freezer.
• Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
• The cooling plate or refrigerated freezer shelves
in this appliance contain channels through which
the refrigerant passes. If these are punctured this
will cause substantial damage to the appliance
and result in food loss. DO NOT USE SHARP
INSTRUMENTS to scrape off frost or ice. Under
NO circumstances should solid ice be forced off
the lining or shelves. Solid ice should be allowed
to thaw, when defrosting the appliance. See
Defrost Instructions.
Maintenance and Cleaning
• Switch off and unplug the appliance before
carrying out any cleaning or maintenance work.
Servicing
• This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
• Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
Service Force Centre and always insist on
genuine spare parts.
IMPORTANT SAFETY INFORMATION
3
IMPORTANT SAFETY INFORMATION
Building the appliance in
• Fit the appliance into the recess.
• Rotate the bracket of 180° in order to obtain the
right position ( 2).
The position (1) is on the delivery.
• Fix it to a solid wall with the appropriate bracket.
1
2
Disposal of old Appliances
The symbol on the product or on its
packaging indicates that this product may not be
treated as household waste. Instead it shall be
handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product, please
contact your local city office, your household waste
disposal service or the shop where you purchased
the product.
At the end of the Appliance
Life
• When disposing of your appliance, use an
authorised disposal site.
• Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
4
CONTENTS
Instructions for the User
Important Safety Information
2
Operation
5
Before using 5
Use of the freezer - Control panel 5
Freezing fresh food 6
Storage of frozen food 6
Thawing 7
Making ice cubes 7
Freezer compartment 7
Useful hints for freezing 7
Use of the refrigerator - Control panel 8
Dynamic Air Cooling 9
Operation 9
Refrigerator compartment 9
Maintenance and Cleaning
10
Periodic cleaning 10
Defrosting 10
Replacing the bulbs 10
Something Not Working
11
Service and Spare Parts
12
Customer Care
12
Guarantee Conditions
13
Instructions for the
Installer
Technical Specification
14
Installation
15
Positioning 15
Electrical Connection
16
Positioning
17
Height adjustment 17
Fitting the side panels 17
Adjustment door (if necessary) 18
Building the appliance in 19
Fitting the plinth 19
5
OPERATION
Before using
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Control panel
Use of the freezer
ECD
F
A
B
G
H
I
A ON/OFF light
B Freezer button ON/OFF
C Temperature setting button (warmest)
D Temperature indicator
E Temperature setting button (coldest)
F Alarm reset light
G Alarm reset button
H Fast Freeze light
I Fast Freeze button
A. Light ON/OFF
B. Button ON/OFF
ON: Press the button (B). The pilot light (A)
illuminates.
OFF: Keep the button (B) until the pilot light (A) and
the temperature indicator switches off.
Attention!
During the initial stabilising period the temperature
displayed cannot correspond to the requested
temperature.
D. Temperature display
During normal use the display shows the
temperature inside the freezer.
Attention!
A difference between the temperature display and
temperature setting is normal. Especially when:
- a new setting has recently been selected
- the door has been left open for a long time
- warm food has been placed in the compartment.
C - E. Temperature setting buttons
The temperature can be adjusted between -15°C
and -24°C.
By pressing the button (C or E), the current
temperature setting flashes in the display. It is only
possible to modify the temperature with the indicator
flashing. To set a warmer temperature, press button
(C). To set a colder temperature, press button (E).
The indicator displays the newly selected
temperature for a few seconds and then shows again
the internal compartment temperature.
The newly selected-temperature should be reached
within 24 hours.
6
Storage of frozen food
When first starting-up or after a period out of use,
before putting the products in the compartment let
the appliance run for at least two hours on the Fast
Freeze setting, then push the Fast Freeze button
again.
Do not exceed the storage period indicated by the
manufacturer.
Finally, do not open the door frequently or leave it
open longer than is absolutely necessary.
Warning
Do not put carbonated liquids, (fizzy drinks etc.), in
the freezer compartment.
Ice lollies, if consumed immediately after removal
from the freezer, can cause low temperature skin
burns.
Do not remove items from the freezer if your hands
are damp/wet, as this could cause skin abrasions or
“frost/freezer burns”.
Important
In the event of a power cut the food in the freezer will
not be affected if the power cut is short and if the
freezer is full. Do not open the door. Should the food
begin to thaw, it must be consumed quickly and must
not be re-frozen .
F. Alarm reset light
G. Alarm reset button
In the event of an abnormal temperature rise inside
the freezer (e.g. power cut) warning light (F) will start
to flash and a buzzer will sound.
After the temperature has returned to normal, the
warning light (F) will continue to flash, although the
buzzer has stopped.
When the alarm button (G) is pressed, the warmest
temperature reached in the compartment flashes in
the display (D).
Operation
Insert the plug in the power socket. Press the button
ON/OFF (B). The freezer is switched on.
The freezer is pre-set to run at -18°C. This
temperature will be reached in a few hours.
As soon as the appliance is switched on the
temperature indicator (D) shows the current
temperature inside the freezer, the alarm reset light
(F) flashes and a buzzer sounds. Press the alarm
reset button (G). The buzzer stops and the alarm
light (F) continues to flash until the requested
temperature is reached.
H. Fast Freeze pilot light
I. Fast Freeze button
To freeze fresh foods, the “Fast freeze” function must
be actived. Press the fast freeze button (I).The
relevant pilot light (H) illuminates. When this function
is on, SP is shown in the display .
The function can be deactived at any time, by
pressing the button (I), otherwise it automatically
switches off. With the function deactived the pilot light
(H) switches off.
Freezing fresh food
To freeze fresh food, press the Fast Freeze button (I)
at least 24 hours before.
Place the food to be frozen in the fast freeze
compartment. The maximum quantity of food which
can be frozen in 24 hrs. is shown on the rating plate.
about 6 hrs
before
about 24 hrs
before
not needed
not needed
Introducing small quantities of fresh food
(about 5 kg)
Introducing the maximum quantity of food
(see rating plate)
Introducing frozen food
Introducing small quantities of fresh food
daily 2 kg maximum
Warning!
When to use the “Fast Freeze” function:
7
Thawing
Frozen food, prior to being used, can be thawed in
the fridge or at room temperature depending on the
time available. Small food items may even be cooked
from frozen; in this case cooking will take longer.
Any frozen food which is allowed to thaw accidentally
should either be eaten as soon as possible or thrown
away. Alternatively, if the food is uncooked and has
not been completely defrosted it can be cooked and
then refrozen.
Meat, fish and fruit should be thawed in the
refrigerator compartment and small pieces of meat
can even be cooked while still frozen, but you must
ensure that it is thoroughly cooked through.
Vegetables should be directly immersed in boiling
water; ready-cooked dishes can be placed directly in
the oven in their aluminium wrapping.
A microwave oven is particularly suitable for thawing
any type of frozen or deep-frozen food: follow the
oven instructions, particularly regarding the
placement of aluminium wrapping or containers in
the oven.
Defrosted cooked food must never be refrozen.
Making ice cubes
The appliance is provided with one or more trays for
ice-cubes.
Fill the tray(s) 3/4 full to give the ice space to expand
and place them in the freezer compartment.
To release the ice cubes simply give the tray a slight
twist.
Do not use sharp or metallic instruments to remove
the trays from the freezer.
Freezer compartment
• If food is to be frozen immediately after having
installed the appliance or after a prolonged period
out of use, push the button (I) and allow the
appliance to run for at least 4 hours before
placing the food in it.
If the freezer is already operating, with food inside
it, push the button (I) 24 hours before loading
food to be frozen.
• The alarm light indicates when the temperature
inside the freezer compartment has risen to a
point at which safe storage of frozen foods can no
longer be guaranteed. When the appliance is first
started up, or after having loaded a quantity of
food to be frozen, this warning light will stay or
until a safe storage temperature has been
reached.
• Products to be frozen should be placed in the fast
freeze compartment and, once frozen, moved to
the storage baskets.
• The maximum freezing capacity is 13 kg in 24
hours. Do not freeze more than this quantity at a
time.
Useful hints for freezing
• Products to be frozen should be fresh and clean.
• Pack foods in suitable family portions which can
be used up all at once.
• Small packs allow fast and uniform freezing.
• Lean foods keep better and longer than fatty
foods. Salt reduces the storage life of food.
• Wrap foods closely in aluminium foil or plastic
bags or film, and make sure they are properly
sealed.
• Attach a label to each pack, indicating the
contents and the date on which it was prepared.
• Never place hot foods, bottles or containers with
fizzy drinks in the freezer (they could explode).
• Do not fill containers with lids right to the brim.
• Do not add more food or open the doors during
the freezing process.
• Never place food to be frozen in contact with
already frozen food, as this would increase the
temperature of the latter.
8
NLM
O
J
K
P
Q
R
Control Panel
J ON/OFF light
K Fridge button ON/OFF
L Temperature setting button (warmest)
M Temperature indicator panel
J. Light ON/OFF
K. Button ON/OFF
ON: Press the button (K). The pilot light (J)
switches on.
OFF: Keep the button (K) pressed until the pilot light
(J) and the temperature indicator switches off.
L - N. Temperature setting buttons
The temperature can be adjusted between +2°C and
+8°C.
By pressing the button (L or N), the current
temperature setting flashes in the indicator panel. It
is only possible to modify the setting temperature
only with the indicator flashing. To set a warmer
temperature, press button (L). To set a colder
temperature, press button (N). The indicator panel
displays the newly selected temperature for a few
seconds and then shows again the internal
compartment temperature.
The newly selected-temperature should be reached
after 24 hours.
Attention!
During the initial stabilising period the temperature
displayed cannot correspond to the requested
temperature. During this time it is possible that the
temperature displayed is lower than the actual
temperature.
M. Temperature indicator
During normal operation the indicator shows the
temperature inside the fridge.
Attention!
A difference between the temperature displayed and
temperature setting is normal. Especially when:
- a new setting has recently been selected
Use of the refrigerator
- the door has been left open for a long time
- warm food has been placed in the compartment
O. Super Cooling pilot light
P. Super Cooling button
The maximum performance is obtained by setting
the Super Cooling function. It’s recommended when
loading large quantities of food.
Press the Super Cooling button (P).The relevant pilot
light (O) illuminates.
The internal temperature goes down to +2°C.
After about 6 hours the Super Cooling function
switches off automatically.
Q. Dynamic Air Cooling light
The D.A.C. light is on by pushing the D.A.C. button.
R. Dynamic Air Cooling button
Push the D.A.C. button the light will illuminate.
N Temperature setting button (coldest)
O Super Cooling light
P Super Cooling button
Q Dynamic Air Cooling light
R Dynamic Air Cooling button
9
Refrigerator compartment
For proper opening and closing, it is advisable to act
on both doors simultaneously (as shown in the
figure).
• Do not place hot food or drinks in the refrigerator;
wait until they have cooled to room temperature.
• Always cover foods, especially those which are
strong-smelling or aromatic.
• Place foods so that air can circulate freely round
them.
The temperature selected may be adjusted to
compensate for temperature variations due to:
• The frequency with which the doors are opened.
• Difference in ambient temperature.
• Quantity of food being stored.
To make the best use of available space, the front
half-shelves may be stacked on top of the rear
halfshelves.
To achieve automatic defrosting of the refrigerator,
the compressor must cut out from time to time. If the
bottom of the compartment becomes covered with
too much frost, push the warmer temperature button
(L) until the compressor starts to cut out periodically.
LIGHT
Fig. 1
Air recycling
The refrigerator compartment is equipped with a
special D.A.C.(Dynamic Air Cooling) fan which can
be turned on with the button (R- see the control
panel). The green light (see fig. 1), when on, means
that the fan is working.
It is suggested that the fan (D.A.C.) be used when
the ambient temperature exceeds 25°C .
This device allows for rapid cooling of foods and a
more uniform temperature in the compartment.
Operation
Insert the plug in the power socket. Press the button
ON/OFF (K). The fridge is switched on.
The fridge is pre-set to run at +5°C. This temperature
will be reached in a few hours.
10
D051
Before carrying out any maintenance operations,
including those described in this book, unplug
the appliance from the mains supply.
Warning
This appliance contains hydrocarbons in its cooling
unit; maintenance and recharging must therefore
only be carried out by authorised technicians.
Periodic cleaning
Clean the inside of the appliance and the accesso-
ries with a solution of lukewarm water and bicar-
bonate of soda (5 ml to 0.5 litre of water). Rinse and
dry thoroughly.
The freezer compartment drawers can be removed
for washing. To remove the drawers, pull them out
until they reach the stop, then lift and withdraw them
from the guides. To refit the drawers, engage them in
the guides then, keeping them tilted, push them
inwards.
Defrosting of the refrigerator
To achieve automatic defrosting of the refrigerator,
the compressor must cut out from time to time. If the
bottom of the compartment becomes covered with
too much frost, select the temperature towards a
warmer setting until the compressor starts to cut out
periodically.
It is important to periodically clean the defrost water
drain hole in the middle of the refrigerator
compartment channel to prevent the water
overflowing and dripping onto the food inside. Use
the special cleaner provided, which you will find
already inserted into the drain hole.
Important:
Never use sharp metal tools to scrape off frost
from the evaporator as you could damage it.
Do not use a mechanical device or any artificial
means to speed up the thawing process other
than those recommended by the manufacturer.
Replacing the bulbs
Refrigerator compartment
Unscrew the light cover as shown. Remove the bulb
and replace it with one of the same power (the
maximum power is shown on the light diffuser)
available from your nearest Service Force Centre.
Replace the light cover.
D037
MAINTENANCE AND CLEANING
11
SOMETHING NOT WORKING
Symptom
No power to the appliance
The light does not come on
The temperature in the fridge or freezer section is
too high
The freezer door will not open
The compressor runs continously
Excessive frost and ice has built up
Noise
Water under the salad bin
Solution
Check there is power at the socket.
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown.
Ensure that the bulbs are correctly fitted.
Replace the bulb if it has blown.
Check the door light switch is not jammed.
Check the temperature control in the fridge is to the
correct setting relative to ambient conditions.
Check the ambient temperature is within the
appliance’s operating limits, please refer to the
installation section in this instruction book.
Relocate the appliance if necessary.
Has door just been opened? If so leave for a few
minutes to allow the air pressure to equalise.
Adjust the temperature control to give correct
temperature control. See “Setting the temperature”.
Check that the doors are closed.
Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
Check that air ventilation is not obstructed.
Ensure the doors are not left open.
Check that nothing is preventing the doors from
closing.
Is the door gasket intact and clean.
Refer to normal operating sounds.
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation a charge will be made, even if the appliance is under guarantee.
Before contacting your local Service Force Centre, check the following points:
If, after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
12
CUSTOMER CARE DEPARTMENT
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Zanussi Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at www
.serviceforce.co.uk
For Customer Service in the Republic of Ireland please
contact us at the address below:
Zanussi
Electrolux Group (Ire) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Telephone : +353 (0)1 4090751
Email: ser[email protected]
Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products,
please contact our Customer Care Department by letter or telephone at the address below or visit our website
at www
.zanussi.co.uk
Customer Care Department
Major Appliances
Zanussi
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 727 727 ( * )
* calls to this number may be recorded for training purposes.
SERVICE AND SPARE PARTS
13
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or
defective part replaced shall become the Company’s property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
European Community (EC) or European Free Trade Area.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of
use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France Senlis +33 (0)3 44 62 29 29
Germany Nürnberg +49 (0)800 234 7378
Italy Pordenone +39 (0)0434 39 4700
Sweden Stockholm +46 (0)8 672 53 90
UK Luton + 44 ( 0) 8705 727727
14
TECHNICAL SPECIFICATIONS
POWER SUPPLY VOLTAGE AND FREQUENCY 230-240 V / 50 Hz
TOTAL POWER ABSORBED 240 W
AVERAGE DAILY UNITS ELECTRICITY * 1.14 kWh
GROSS CAPACITY
Fridge 342 L
Freezer 128 L
NET CAPACITY
Fridge 338 L
Freezer 96 L
STAR RATING
*
This figure is based on standard test results in accordance with
European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
15
Warning
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located at the left on the inside of the
appliance.
The following table shows which ambient
temperature is correct for each climate classification:
SN +10°C to + 32°C
N +16°C to + 32°C
ST +18°C to + 38°C
T +18°C to + 43°C
The appliance should be located in a dry
atmosphere, out of direct sunlight and away from
continuous heat and extreme temperature, e.g. not
next to a boiler or radiator, or in a very cold room e.g.
an outhouse. If these temperatures are exceeded i.e.
warmer or colder, then the appliance may not
operate correctly.
For building-in instructions please refer to the
instructions on the following pages.
INSTALLATION
Important
It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.
16
Electrical connections
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol or coloured green and
yellow.
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
D207
GREEN & YELLOW
13 AMP. FUSE
BROWN
CORD CLAMP
BLUE
13 AMP
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
This appliance complies with the following
E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.
17
Height adjustment
The height of the appliance is adjustable by 50 mm.
in order that the lower doors line up with existing
kitchen units.
Before installing the appliance between units, adjust
the height of the feet and rear wheels. The wheels
are factory set for a work top height of 820 mm. To
align the appliance to work top height of 870 mm,
raise it by adjusting the feet with a spanner, then
remove the wheels and refit them in the lowest
position.
Fitting the side panels
• Fit the brackets onto the panels in the positions
shown in the diagram. The dimension of 260* mm
is allowed for fitting a 100 mm plinth below the
panel. For different plinth sizes, increase the
dimension of 260* mm accordingly.
• Rest the panels against the appliance.
• Fit the rear brackets, taking into account the
thickness of the panels (maximum width of unit
900 mm).
• For a correct alignment make sure that the
distance between the appliance and the cabinet
is of 45 mm.
• Secure the panels at the front.
• Check the alignment of the doors, loosening the
fixing nuts and screws and by means of the slots.
• Tighten the clamp screw on the bottom hinges of
the doors.
820
870
POSITIONING
820
870
15
820
15
280
541
30
539
260*
1015
64
17,5
RIGHT HAND
SIDE PANEL
FRONT
EDGE
INSIDE
FACE
REAR
EDGE
18
• Close the door and check that the small door is
positioned at the required height, removing the
bracket cover and operating the adjustment
screws if necessary.
• Use the same adjustment screws to align the
doors vertically.
• Check horizontal alignment of the outer door
panels and, if necessary, correct their position by
moving them along the slots.
• Open the door.
Adjust the levelness of the small doors by means
of the bracket and small bottom bracket.
• After aligning the doors, fix the nuts of the bracket
and the screws of the small bottom bracket.
• Then refit the bracket cover.
Adjustment panels (if necessary)
=
=
10
19
Building the appliance in
• Fit the appliance into the recess.
• Rotate the bracket of 180° in order to obtain the
right position ( 2).
The position (1) is on the delivery.
• Fix it to a solid wall with the appropriate bracket.
• The top of the appliance must be kept clear to
allow correct air circulation. If a wall unit is fitted
above the appliance, there must be a gap of 50
mm between this unit and the wall and it must be
at least 50 mm below the ceiling.
Fitting the plinth
Alignment height of 820 mm
• If using a 140 to 170 mm plinth, make a cut-out
as shown.
• If using a plinth higher than 100 mm but less than
140 mm, cut the height compensation strip
supplied with the appliance to the required depth
and fit it between the plinth and the ventilation
grill, pressing it into position below this grill.
25
50
50
870
820
140
190
30
100
900
170
220
140
190
1
2
20
100
150
30
100
E
• If using a 100 mm plinth, fit the complete height
compensation strip.
Alignment height of 870 mm
• If using a 190 to 220 mm plinth, make a cut-out
as shown on the previous page.
• If using a plinth higher than 150 mm but less than
190 mm, cut the height compensation strip
supplied with the appliance to the required depth
and fit it between the plinth and the ventilation
grill.
• If using a 150 mm plinth, fit the complete height
compensation strip.
• If the appliance is installed at the end of a row of
units, insert foot E to hold the plinth in place.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Zanussi ZJB9476X is an appliance with two compartments: freezer and refrigerator. The freezer compartment, which has a capacity of 93 litres, is equipped with the Fast Freeze function. This function, which should be activated at least 24 hours before freezing fresh food, helps to maintain the quality of the food by quickly freezing it. The refrigerator compartment, with a capacity of 226 litres, is equipped with Dynamic Air Cooling, which ensures an even temperature distribution throughout the compartment.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Electrolux ERG47800 User manual
-
Zanussi-Electrolux ZECBFF/W User manual
-
Küppersbusch ITE 139-0 Operating Instructions Manual
-
Zanussi-Electrolux ZX99/3W User manual
-
-
Neue BUFRE2W User manual
-
Neue BUFRE2W User manual
-
Electrolux ERN23800 User manual
-
Hoover VCN6185B User manual
-
