2. Whirlpool
  3. AKZ 810/IX
AKZ 810/IX

Whirlpool AKZ 810/IX, BLZS 7200 IN Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Whirlpool AKZ 810/IX Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
13
INSTRUCTIONS FOR USE
COLUMN OVEN INSTALLATION
.................................................................
To make the most of your new oven, read the user instructions carefully and keep them to hand
for future consultation.
10200380GB.fm Page 13 Wednesday, March 26, 2008 9:51 AM
14
Column oven installation
Important notes
Important: Make sure to disconnect the oven from the power supply before carrying out any
installation or maintenance work on the appliance.
•
Installation must be carried out by a qualified technician in compliance with the manufacturer's
instructions and local safety regulations.
•
After unpacking the oven make sure it was not damaged during transport and that the door closes
properly.
In the event of problems, contact the dealer or your nearest After-Sales Service
Centre
.
•
After unpacking the oven, leave it on the polystyrene base: this will prevent any damage to the
appliance.
•
It is advisable to wear protective gloves when installing the appliance.
•
The oven is provided with two side handles
(B)
to facilitate installation (Fig. 7).
Preparing the housing unit
•
Kitchen units next to the oven must be heat resistant (min. 80 °C).
•
Carry out all cabinet cutting work before fitting the appliance in the housing. Ensure you remove all
wood chips and sawdust, which could hinder correct appliance operation.
•
For installation as shown in Fig. 2, recipients containing liquids must not be placed on the top part of
the column unit. Grilles can be applied to partly close the opening, in any case maintaining a working
area of 100 cm
2
.
•
The dimensions of housing units are given in figures 1, 2 and 3. Oven dimensions are given in fig. 4.
•
To ensure adequate ventilation, leave an open space at the back of the housing (observing the
dimensions given in Fig. 6).
After installation, the bottom of the oven must no longer be
accessible
.
•
Install the oven making sure its walls do not directly touch the adjacent kitchen units (Fig. 5).
1
2
3
4
10200380GB.fm Page 14 Wednesday, March 26, 2008 9:51 AM
15
•
For ovens installed under the worktop, leave a gap of at least 5 mm between the top edge of the oven
and the bottom edge of the worktop (fig. 5).
To avoid compromising correct appliance
operation, never obstruct this gap
.
•
If the kitchen unit is not securely fixed to the wall, it must be anchored with commercially available
brackets
(A)
(Fig. 6).
Electrical connection
Earthing of the appliance is compulsory by law.
•
The electrical connection of the appliance must be carried out by a qualified electrician, in accordance
with the manufacturer's instructions and local safety regulations.
•
The installer is responsible for correct electrical connection of the appliance and compliance with the
current local regulations on safety.
•
The power cable must be long enough for connecting the appliance, fitted in the cabinet, to the power
socket.
•
For installation to comply with current safety regulations, an all-pole disconnect switch with minimum
contact gap of 3 mm must be utilized.
•
Do not use multiple adapters or extension leads.
•
The electrical components must not be accessible after installation.
5
6
10200380GB.fm Page 15 Wednesday, March 26, 2008 9:51 AM
16
Connecting the oven
•
Make sure the power voltage specified on the appliance dataplate is the same as that in your home.
The rating plate is on the front edge of the oven (visible when the door is open).
•
Power cable replacement (see table) must only be carried out by contacting an Authorised After-Sales
Centre.
Securing the oven
•
Lift the oven using the handles provided
(B)
on the sides and insert it in the housing unit,
making sure the power cable does not become trapped (fig. 8).
•
Align the oven centrally in the housing unit before securing it.
•
Next secure the oven to the housing unit with the screws supplied (Fig. 9).
Power supply cable table
N° of conductors Type of cable
1N+
~
H05 RR-F 3 X 1.5 mm²
8
7
9
10200380GB.fm Page 16 Wednesday, March 26, 2008 9:51 AM
/