30
In this fully integrated appliance the controls are located on the
top of the door. When selecting a programme, the door needs
to be open.
1. Check that the baskets have been
loaded correctly and that the spray
arms can rotate freely
2. Turn on the water tap
3. Press the On/Off push button
The indicator lights of the programme selection push
buttons illuminate and in the digital display are visible 2
horizontal lines (--) (setting mode).
4. Setting and starting the programme
To select a programme, press indifferently one of the two
programme selection push buttons, the indicator lights of
the programme selection push buttons start to flash and
in the digital display will appear the number corresponding
to the last performed washing programme.
Using these two push buttons you have a growing (+) or
a decreasing (-) order in the selection of the programme.
(see "Washing programmes" chart for the number of the
programme).
Example:
push button (growing order): 1P → 2P → 3P etc...
push button (decreasing order): 1P → 7P → 6P etc...
The number of the programme flashes in the digital
display.
The start of the programme will occur only after the
closure of the door.
Select also (if foreseen with the programme) the "half
load" option. The corresponding indicator light illuminates.
Close the dishwasher door, the programme will start
automatically.
5. To interrupt, change or cancel a
washing programme
Interrupt, change or cancel a washing programme in
progress ONLY if it’s absolutely necessary
To interrupt a washing programme
Attention! Hot steam may escape when the door is
opened. There is risk of scalding. Open the door carefully.
● Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the point
in which it was interrupted.
To change a washing programme
● Change a washing programme before closing the
door; simply select a new washing programme by
pressing the programme selection push buttons.
● Change a washing programme in progress; you have
to reset the dishwasher by cancelling the running
programme (see "To cancel a washing programme").
To cancel a washing programme in
progress
Open the dishwasher door.
Press simultaneously the function push buttons 2 and 3
for about 2 seconds, the indicator lights of the programme
selection push buttons start flashing for about 2 seconds.
After about 2 seconds the indicator lights of all the push
buttons will illuminate indicating that the running
programme has been cancelled and that the machine has
returned to setting mode.
It is now possible to select and start a new washing
programme.
6. Setting the "delay start"
The setting of the delay start occurs after selecting
the programme.
Setting the "delay start"
Press the "delay start" push button, the indicator light
corresponding to the push button illuminates and in the
digital display appears 1h.
Press the delay start push button until in the digital display
will appear the number of hours desired (from 1 hour up to
19 hours).
The countdown will start only once the door has been
closed, until then it is possible to modify the number of
hours by pressing the delay start push button.
Close the door, the countdown will start automatically.
The countdown will decrease with steps of 1 hour.
The opening of the door during the countdown will not
modify the delay start.
Once the delay start has elapsed the programme will start
automatically.
To change the "delay start"
As long as the washing programme has not started, you
can change the number of hours for the delay start by
pressing the "delay start" push button.
To cancel the "delay start"
As long as the washing programme has not yet started,
you can cancel the delay start setted by pressing the
"delay start" push button until in the digital display
appears the time duration of the selected programme.
The washing programme will start immediately, once
closed the door.
To change a programme after the start of
the "delay start"
If you want to change the selected washing programme
after the start of the delay start you have to reset the
dishwasher by cancelling the previous setting (also the
setting of the delay start will be lost).
Press simultaneously the function push buttons 2 and 3 for
about 2 seconds, the indicator lights of the programme
selection push buttons start flashing for about 2 seconds.
After about 2 seconds the indicator lights of the
programme selection push buttons will illuminate and in
the digital display will appear 2 horizontal lines (--)
indicating that the running programme has been cancelled
and that the machine has returned to setting mode.
It is now possible to set a new washing programme.
Starting a washing programme