MBJ ARL-10 User manual

Type
User manual

MBJ ARL-10 is a ring light that can be used for various applications, including brightfield microscopy, machine vision, and quality control. It is equipped with a 45° inward angle of illumination, which is ideal for highlighting surface structures and emphasizing angled edges. The light has a luminous area diameter of 62 mm - 101 mm and a luminous flux of 1840 lm. It can be operated in four different modes: steady light, steady light with brightness control, triggered light, and triggered flash light.

MBJ ARL-10 is a ring light that can be used for various applications, including brightfield microscopy, machine vision, and quality control. It is equipped with a 45° inward angle of illumination, which is ideal for highlighting surface structures and emphasizing angled edges. The light has a luminous area diameter of 62 mm - 101 mm and a luminous flux of 1840 lm. It can be operated in four different modes: steady light, steady light with brightness control, triggered light, and triggered flash light.

Angled Ringlight
Operating Manual
Technical Data
Model Sizes in Series
The light is available in the following size 1)
ARL-10
1) Size definition refers to the outer luminous area diameter in cm.
Possible LED Colors
LED Abbr.1) Peak Wavelength2)
White -WT 5000 K, CRI80
Red -RD near 625 nm
Infrared -IR near 850 nm
Green -GN near 525 nm
Blue -BE near 465 nm
Yellow -YE near 580 nm
1) Color option will be added to the model name aer the size information.
ARL-10-WT refers to an angled ringlight with 5000 K white light
2) This is an approximated value. The exact value also depends on LED temperature
and LED current.
MBJ Imaging GmbH
Jochim-Klindt-Straße 7 +49 4102 778 90 - 31
22926 Ahrensburg, Germany [email protected]
www.mbj-imaging.com
Mechanical Integration
The lights are equipped with 4 combined mounting positions of thread-
ed or through holes. It can be used to fix the lighting to the specified
position. To secure a long live time additional heat transfer measure-
ments at the holding positions are highly recommended.
03590.00 Manual MBJ Angled Ringlight, April 2023
Safety Notes
Before working with this unit, read the warning and application instruc-
tions carefully and completely before operating the device.
Have the illuminators commissioned only in compliance with the
specified protective measures. It is essential that you comply with the
permissible ambient conditions. The lighting must be switched o before
installation and/or maintenance. The device must not be used when a
failure may cause personal injury.
1. The device is designed for indoor use only.
2. Light – Due to the risk of irritation of or damage to the eyes or
skin it is not recommended to look directly into the light source.
3. Heat –In case of insufficient heat dissipation or when running the
light in flash mode with a too high duty cycle, the surface tempera-
ture may get hot. Do not touch the product during operation or
immediately after it is turned off. Keep off flammable materials at
any time and allow for sufficient heat dissipation.
4. Electricity – The housing is electrically isolated from the ground
of the power supply. Operate only with the permissible current.
Exceeding the permissible current can lead to the destruction of
the device or to a significant shortening of the lifetime of the LEDs
in the device.
5. Usage – Please prevent mechanical stress to the light surface during
operation. This will lead to an inhomogeneous light emission.
6. Cleaning – The light emission surface has to be cleaned with a
standard glass cleaner and a soft cleaning cloth. Do not use other
material for cleaning as it will damage the device.
Model ARL-10
More 2D and 3D drawings can be found online:
www.mbj-imaging.com
Specification Angled Ringlight
Operating temperature 10°C to 30°C / 45°C1)
Certifications CE, RoHS
Degree of protection IP542)
Humidity 30 % to 70 %
1) Max. of 30°C is recommended for steady light operation w/o additional heat
transfer measurements, for max. 45°C a thermal connection is mandatory. Max.
of 45°C is also permissible for flash light operation with a max. 10 % duty cycle.
2) MBJ LED lights are protected against the ingress of solids and water in accor-
dance with the selected protection class and applicable standards. Permanent
protection against liquids containing solvents, such as cleaning agents, machine
emulsions or other lubricants, cannot be guaranteed. IP is only valid with a
connected cable (MBJ cable recommended).
Specification ARL-10
Optical parameter
Luminous area (ID-OD) 62 mm - 101 mm
Light emission Ring shaped light field with direct light emission in a 45° inward angle
Recommended use Commonly used for partial brightfield applications. Emphasizes surfaces structures. Angled edges are highlighted, slight recesses illuminated.
Recommended light working distance 30 mm - 200 mm
Luminous Flux of white LEDs1) 1840 lm
Radiant Power of red LEDs [mW] 1) 5413 mW
Radiant Power of IR LEDs [mW] 1) 2602 mW
Electrical parameter
Available interfaces -s with integrated LED Controller and 4 operation modes; -x with direct LED access (external LED control is required)
Uin for -s Version 24V DC +/- 5%
ULed(+) range for -x version2) WT / BE / YE: 17 … 20 VDC; GN: 20 ... 23 VDC; RD: 12 … 15 VDC; IR: 9 … 12 VDC
Typical Power (-s version)
Steady light operation (white / red / IR)3) 11 W / 9 W / 6 W
During ON time at flashed light operation4) 31 W
Recommended LED current (-x version)
Steady light (100% duty cycle) 600 mA (900 mA for IR)
Flash light (50% duty cycle, < 500 ms pulse) 1200 mA (900 mA for IR)
Flash light (25% duty cycle, < 50 ms pulse) 1800 mA (900 mA for IR)
Flash light (10% duty cycle, < 5 ms pulse) 2400 mA (1800 mA for IR)
General parameter
Dimension (H x W x D)5) 110 mm x 121 mm x 28 mm
Lens hole diameter [Ø] 53 mm
Weight 420 g
Material Anodized aluminum housing with PMMA light cover
Connector M8x1 socket, 4 pin, male (for pinning details refer to chart “Electrical Connection”)
Accessories For cable, mounts and LED controller please check www.mbj-imaging.com
1) Values are approximate with a +/- 7 % tolerance.
2) Lower voltage value refers to steady light, higher voltage value refers to flash light, please see max. allowed current in the rows below.
3) Power for Blue / Yellow is comparable to White, Power for Green is approx. 1,2 times higher.
4) Triggered flash light with max. 20ms and up to 100% more light intensity, calculated for White.
5) w/o connector
Triggered light with NPN sinking output
(inverted strobe signal, open collector)
Flashed light with PNP sourcingSteady light Steady light with brightness control
Application Samples for (-s) controller
1 Power
2 Dim
3 Trigger
4 GND
24 VDC
MBJ
LED light
MBJ
LED light
1 Power
2 Dim
3 Trigger
4 GND
24 VDC
24 VDC
10k
10k
24 VDC
2k2
10 mA
from Camera/ PLC etc MBJ
LED light
1 Power
2 Dim
3 Trigger
4 GND
2k2
MBJ
LED light
1 Power
2 Dim
3 Trigger
4 GND
24 VDC 24 VDC
10 mA
from Camera/ PLC etc
Electrical Connection
The lighting is equipped with an 4 pin M8x1 connector.
Pin Color 1) Standard (-s) Direct (-x) 2)
1 brown 24 VDC LED (+)
2 white Dim LED (+)
3 blue Trigger LED (-)
4 black Ground LED (-)
1) wire color of MBJ lighting cable
2) connection to 24 VDC without external LED controller may destroy the unit
Additional Information:
Pin3 (Trigger) is an ‘active high’ input signal with 5…24V = ON and 0..1V = OFF, it is a high
resistance current sink with 0.2mA for 5V and 5mA for 24V.
Pin2 (DIM) is used as brightness control and operation mode switch, it is a high resistance
current sink with 0.2mA for 5V and 1mA for 24V.
For connection it is recommended to use the MBJ lighting cable with a maximum length
of 10 m.
Integrated Controller (-s)
Supported operation modes with the integrated LED controller
Pin 2 (Dim) Operation mode
24 Vsteady light 1)
1...10 Vsteady light with brightness control 2)
24 Vtriggered light
GND triggered flash light with max. 20 ms and
up to 100 % more light intensity 3)
1) Pin 3 (Trigger) needs permanent 24 V to activate steady light mode
2) PWM with 3.8 kHz clock is used, recommended minimal camera exposure is 5 ms
3) Latency between trigger and LED light ON is about 20..30 µs,
maximum recommended clock speed is 1 kHz
maximum recommended duty cycle is 25 %
minimum recommended flash time is 100 µs
  • Page 1 1
  • Page 2 2

MBJ ARL-10 User manual

Type
User manual

MBJ ARL-10 is a ring light that can be used for various applications, including brightfield microscopy, machine vision, and quality control. It is equipped with a 45° inward angle of illumination, which is ideal for highlighting surface structures and emphasizing angled edges. The light has a luminous area diameter of 62 mm - 101 mm and a luminous flux of 1840 lm. It can be operated in four different modes: steady light, steady light with brightness control, triggered light, and triggered flash light.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI