Haier HTW70-M1217 User manual

Please read this manual carefully before

operating your washing machine and retain

it for future reference.

TWIN TUB WASHING MACHINE

USER MANUAL

MODEL

HTW70-M1217

HTW90-M1217

HTW110-M1217

HTW130-M1217

CONTENTS

Product Overview

Meaning and description of the symbols

Warning sign

Forbidden sign

Safety precautions

Contents marked with this symbol are

related to the safety information of the

products. Please operate in accordance to

the contents of this manual, to prevent

personal injury or property damage.

Ensure the plug is removed and the taps

turned off in the following cases. Power

failure, cleaning, moving, installation and

when not in use.

Do not install this appliance in a damp or

wet environment. Do not leave wet laundry

on the Control Panel or spray water

directly on to this appliance as this may

cause the washer to malfunction or cause

an electrical fault.

Do not contact to water exceed 50°C in

temperature.

Do not wash water-proof clothing as this

may affect load balance during spin

cycle(s).

The washing machine has ventilation

opening in the base, the opening must

not be obstructed by a carpet.

Ventilation hole at

the bottom of the

washing machine

If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

Safety precautions

Installation and adjustment

Usage of the drain hose

Hose Clamp

Drain Hose

Install the lint filter into the filter case as shown.

Please ensure the lint filter is in place, otherwise the

lint filter may detach from the filter case when the

washing is undergoing and impact on the washing

performance.

Installation and adjustment

Install the water inlet hose; Select the

water level

control panel.

Set the water level according the laundries loaded.

Note: The new hose-sets supplied with the appliance

are to be used and that old hose-sets should not be

reused.

ntin

oot

igure igure

ounting

foot

Before Washing

Preparation before washing

1. Connect the jointer of the water inlet hose to the water

faucet. Turn on the water faucet.

2. The washing machine must be properly grounded. Then

plug in the power cord to the power socket. Do not ground the

washing machine to a gas pipe, water pipe or telephone line.

3. Put down the drain hose.

4. The washing machine must be grounded. Improper placement

may lead to abnormal noise and vibration creation when washing in progress.

Clear the pockets and take out loose items

such as coins, soils, pins and others metal

objects.

Pay attention to following before washing the laundries

Tie any long straps or

strings, button up and

close zippers.

The weight of the laundry

shall not exceed the rated

capacity of your machine,

spread out the laundry

before placing it evenly in

the tub.

Turn the clothing inside out or

put inside the laundry net to

prevent excessive vibration or

noise on the appliance while

operation in progress.

a. Check the care label on the clothing, and sort them accordingly before start the

wash.

b. Separate white from colours.

c. Do not put fabrics that are insoluble in water to the machine.

d. Prewash the soiled clothes and apply detergent directly on the stain before

washing.

e. Turns the clothing inside out before washing to minimize the lint build-up after

washing.

f. Do not put the laundry contaminated with alcohol, paint thinner, gasoline, benzene

and other inflammable or explosive substances like into the washing machine.

Laundry Guidelines

Usage of the detergent :

laundry that could be loaded into the appliance.

actual capacity.

laundries loaded to avoid the water splashing.

powder.

Dissolve directly inside the washing machine:

1. Add some water.

2. Add washing powder. Run for about 30s to fully dissolve the Powder.

3.Put in laundries. Select suitable water level.

Quick dissolving washing powder:

1. Prepare a container and pour in water at 30°C and add washing powder.

2. Stir the mixture until the washing powder dissolve completely into the water.

Apply an appropriate amount of washing powder in accordance to the laundry

volume and select the right water level.

Different type of washing powder request different dosage, refer to the instruction

of washing dosage for details.

bleach

bleach.

Avoid using bleach on the laundries directly. Bleach causes discoloration on

clothes.

for

washing tub.

Please dissolve the powder type bleach before use it.

g q y

DRAIN

Wash timer Wash selector

Wash selector

(HTW70-M1217)

(HTW90-M1217)

(HTW110-M1217)

(HTW130-M1217)

(HTW110-M1217)

(HTW130-M1217)

Drain selector Spin timer

Wash

DRAIN SELECTOR

1. Water inlet selection

2. Turn on the tap and water flow into the tub till

the set water level dissolve the washing powder inside

if needed.

4. Select the strength(Figure 3) and washing

time(Figure 4) according to the laundries loaded.

5. Turn to “Drain” after washing period(Figure 5).

The washing instruction with soaking:

a. 0-15 minutes is normal washing;

b.15-45 minutes is soaking period. The pulsator will run

2.5 minutes each 7.5minutes interval. After soaking period,

will come to normal washing period, which last for 15 minutes.

c.When the user select the soaking, firstly make sure the

detergent power is fully dissolved. Otherwise it may be

harmful to clothing.

The most effective program for white cotton

fabric: STANDARD,washing with 30 minutes

soaking.

allows water inflow

If to set less than 1

min, in order to

ensure a long service

life,please first turn

past 2 min and then

turn back.

If you wish to

set it for less than

5 min ,you should

first turn past

15 min and then

turn back.

(Intensity can

be set to

standard,soft

and drain.)

(Intensity can

be set to

standard,soft

and drain.)

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

(HTW70-M1217)

(HTW90-M1217)

(HTW110-M1217)

(HTW130-M1217)

(HTW70-M1217)

(HTW90-M1217)

(HTW110-M1217)

(HTW130-M1217)

Operation

1. Spread the laundries into the spinning tub evenly.

a.Put and push the inner cover properly no matter how much laundries loaded.

b.Close the spin tub cover and safety cover.

c.Set the spinning time by rotating the spin timer.

Push

Proper Proper

The laundry

is slanted.

Inner cover

No Inner cover

Spin Tub Cover

Safety Cover

3.Shower rinse function operation

a.Turn the water inlet selector from “WASH” to

“SPIN”, let water flowing for a minute.

Too much excessive water inflow in spinning tub

may cause the water overflow to washing tub.

Please kindly turn off the water tap to control

the water level.

b.Close the spin tub cover and set the spinning

time by rotating spin timer.

WASH SPIN

Operation

Rinsing

Overflow-Rinse

1.Unload the laundries from spin tub and load into wash tub, turn the water inlet

selector to WASH. Set the washing time by rotating the wash timer according to

laundries loaded.

2.Adjust the water level according to laundries loaded, turn on the water tap until

the cycle finished.

3.Set the rinse time by rotating the wash timer.

Normal Rinse

1.Unload the laundries from spin tub and load into wash tub, turn the

water inlet selector to WASH. Set the washing time by rotating the wash

timer according to laundries loaded.

2.Adjust the water level according to laundries loaded, turn on the water

tap until reach the set water level.

3.Set the rinse time by rotating the wash timer.

Cautions:

Soft mode apply for small quantity laundries loaded. Standard mode

with small quantity laundries may cause the water splash.

Operation

Final Spin

1.Same as the first spin operation, loaded the wet laundries and put the inner spin

cover inside the spin tub properly.

2.Close the spin tub cover and safety cover.

3.Set the spin time by rotating the spin timer according to the wet laundries loaded.

During the spinning process, there may be noise caused by wet laundries not

loaded properly. Please stop the spinning period and reload the wet laundries

properly.

Spinning process will be automatically cut off once you open the spin tub cover for

safety concern. Please ensure the spin tub cover is closed during the spinning

process.

Before spin, drain or shower rinse, suggest to rotate the

spin timer to set 1 minute spinning, this will help unit to

drain the water stored in the spin tub and get better spin,

drain or shower rinse effect.

Cleaning and Maintenance

Cleaning the lint filter

Remove the power plug before carry out any cleaning and maintenance.

Clean the lint filter and overflow filter after each wash cycle, otherwise it may

influence your next use.

Lint filter must be used during washing.

Clean the line filter after using.

1.Press down the upper area of the filter case to

remove the filter. (Figure 1)

2.Clean the filter with running water. (Figure 2)

3.When cleaning is completed, put the filter back

to filter case. Make sure the filter case fits in

completely, otherwise it will affect the washing

performance. (Figure 3)

Figure 1

Figure 3

Figure 2

Cleaning and Maintenance

Cleaning the overflow filter

Too much lint residual in the overflow filter will affect the performance, please

clean the filter regularly.

1.Remove the overflow filter by pressing the

side handle and pull it out.

2.Clean the filter with running water.

3.When cleaning is completed, press the side handle

and put the filter back to the filter case.

Troubleshooting

Phenomena The reason

Many occurring problems could be solved by yourself without specific expertise. Please

check all the shown possibilities and the solution below before contact the customer care

team. Please switch off the machine and remove the power plug before troubleshooting.

The machine does not start.

The draining function does

not work.

Abnormal sound during

washing.

Abnormal sound and violent

vibration during the spin

cycle.

Water flowing out of the drain

hose during the first use of

the machine.

The spin part does not work.

Is there a power failure?

Is the power plug loose?

Is the pulsator twisted by foreign materials?

Is the drain hose put down?

Is the drain hose frozen?

Is the drain hose blocked by foreign material?

Is there laundry adhering to the outer side of

the spin tub?

Are there hair pins, coins or metal items inside

the tub?

Is the machine slanting?

Is the gland pressed evenly?

Is there laundry adhering to the outer side of

the spin cycle compartment?

Is the spin cycle compartment overloaded?

This is the water left over after the factory

performance inspection.

Is the spin tub outer cover open?

Packing list

Name Quantity

Twin tub washing machine

Water intake hose

User manual

One

Inner Cover One

Mounting foot Four

Hose clamp One

Drain hose One

Lint filter One

Specifications

Haier HTW70-M1217 User manual

Related papers

Other documents