Epson BrightLink 450Wi Installation guide

Installation Guide

Guide d’installation

2

Safety Instructions

For your safety, read all the instructions in this guide before using the setting plate. Incorrect handling that

ignores instructions in this guide could damage the setting plate or could result in personal injury or property

damage. Keep this installation guide at hand for future reference.

Read the safety instructions in the User's Guide for your projector and follow the instructions in this

document.

Explanation of Symbols

The warning marks shown below are used throughout this installation guide to prevent personal injury or

property damage. Make sure you understand these warnings when reading this installation guide.

Safety Precautions for Installation

This symbol indicates information that, if ignored, could possibly result in personal injury or even death

due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical

damage due to incorrect handling.

Symbol indicating an action that must not be done

Symbol indicating an action that should be done

The setting plate is designed specifically for mounting a projector to a wall. If anything other than a

projector is mounted, the weight may result in damage.

If the setting plate falls, it could cause personal injury or property damage.

The installation work (wall mounting) should be performed by specialists who have technical knowledge

and ability. Incomplete or incorrect installation could cause the setting plate to fall and cause personal

injury or property damage. Contact the customer support office listed in “Where to Get Help” in the User's

Guide for your projector when installing the setting plate.

Follow the instructions in this guide when installing the setting plate.

If the instructions are not followed, the setting plate may fall, resulting in personal injury or property damage.

Handle the power cable carefully.

Incorrect handling may cause fire or electric shock. Observe the following precautions when handling:

• Do not handle the power plug with wet hands.

• Do not use a power cable that is damaged or modified.

• Do not pull the power cable with too much force when routing the cable through the setting plate.

When you mount the projector on the wall with the setting plate, the wall requires enough strength to hold

the projector and the setting plate. Confirm the weight of the projector and the setting plate before

installation, and maintain the strength of the wall. If the wall is not strong enough, reinforce the wall

before installation.

Do not install the setting plate in a place where it might be subjected to vibration or shock.

Vibration or shock could cause damage to the projector or mounting surface. It could also cause the setting plate or

projector to fall and cause personal injury or property damage.

Install the setting plate so that it can sufficiently support the weight of the projector and setting plate, and

resist any horizontal vibration. Use M8 nuts and bolts.

Nuts and bolts smaller than M8 could cause the setting plate to fall. Epson takes no responsibility for any damage or

injury caused by incorrect installation.

Warning

Caution

Warning

3

English

Location

•Before installing the projector, verify the power supply wiring for the installation location.

•Install the projector away from other electric devices such as fluorescent lights or air conditioners. Some

kinds of fluorescent lights could interfere with the remote control of the projector.

•It is recommended to keep connection cable length less than 65 ft (20 meters) to reduce external noise.

•Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical

components from becoming dirty.

About This Installation Guide

This guide describes how to mount the BrightLink™ 450 Wi, PowerLite® 460, and PowerLite 450W projectors to

a wall using the exclusive setting plate.

The installation work should be performed by at least two qualified service personnel. If you need to

loosen any screws during installation, be careful not to drop the setting plate.

If the setting plate or projector falls, it could cause personal injury or property damage.

Inspect the setting plate on a regular basis to ensure there are no broken parts or loose screws.

If there are any broken parts, stop using the setting plate immediately. If the setting plate or projector falls, it could cause

personal injury or property damage.

Never modify the setting plate.

Do not hang on the setting plate or hang a heavy object on the setting plate.

If the projector or setting plate falls, it could cause personal injury or property damage.

If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the slide

plate fixing part of the projector, the case may crack and cause the projector to fall, resulting in personal

injury or property damage. Do not use adhesives, lubricants, or oils to install or adjust the setting plate.

Tighten all screws firmly after adjustment.

If the screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property

damage.

Never loosen the bolts and nuts after installation.

Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them firmly. If the

screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property damage.

Do not install the setting plate in a location where the operating temperature for your projector model

may be exceeded.

Such an environment may damage the projector.

Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical

components from becoming dirty.

Do not use excessive force when adjusting the setting plate.

The setting plate may break, resulting in personal injury.

Warning

Caution

4

1Package Contents sPage 5

2Specifications sPage 7

3Connecting Devices sPage 8

4Positioning the Projector sPage 9

(1) Installation worksheet for projecting on a pre-installed wall-

mounted board

(2) Installation worksheet for projecting on a plain wall

(3) Installation measurements in inches

(4) Installation measurements in millimeters

5Installing the Projector sPage 18

(1) Install the wall plate on the wall

(2) Determine the projection distance and pull out the slider

(3) Attach the setting plate to the wall plate

(4) Secure the projector to the setting plate

(5) Connect the power cable and other cables to the projector

6Adjusting the Image sPage 22

(1) Turn on the projector

(2) Display the test pattern

(3) Change the aspect ratio if necessary

(4) Adjust the focus

(5) Use the top adjustment dial to adjust the vertical tilt

(6) Use the right adjustment dial to adjust the horizontal rotation

(7) Use the left adjustment dial to adjust the horizontal roll

(8) Adjust the vertical position

(9) Adjust the forward/backward slide

(10) Turn off the display of the test pattern or computer image

7Attaching the Covers sPage 27

(1) Attach the wall plate cover and end cap

(2) Attach the cable cover to the projector

5

English

1. Package Contents

Mounting hardware

•Use the bolts supplied with the setting plate to install it, as directed in this guide. Do not substitute these

bolts with any other types.

•Use commercially available M8 x 50 mm anchors (at least 3) or 8 x 80 mm lag bolts (at least 3) to attach the

wall plate to the wall.

•Gather the tools and parts you need before you begin installation.

Shape Name Quantity Application

M8 x 15 mm hexagon socket head cap bolt with

washer

2 For installing setting plate

M5 x 12 mm hexagon socket head cap bolt with

washer

2 For securing projector

M4 x 12 mm hexagon socket head cap bolt without

washer

2 For installing wall plate cover

Hexagon wrenches (for M4, M5, and M8)

Wall plate cover

Setting plate (wall mount)

Template sheet

(for installing the wall plate)

End cap

Wall plate

6

Projector box

Interactive pens and

AAA batteries*

Power cord

Projector

Epson Projector

S

oftware for Easy

Interactive Function CD*

VGA computer cable

Remote control

and AA batteries

USB cable*

Epson Projector

Software for Meeting

and Monitoring CD

Security sticker

Projector CD

*Items included for the BrightLink 450Wi only. Extra pen and battery set are included in the U.S. and Canada only.

7

English

2. Specifications

Wall plate

Setting plate adjustment range

Item Specification Remark Reference Page

Setting plate weight Approx. 13.89 lb

(6.3 kg)

Wall plate 4.85 lb (2.2 kg)

Covers and cap 1.04 lb (0.47 kg)

Forward/backward slide

adjustment range

0 to 11.81 in.

(300 mm)

Refer to the figure

below

Vertical slide adjustment range ± 4 ° Minimum: 1.10 in. (28 mm)

Maximum: 1.67 in. (42.5 mm)

s25

Vertical tilt adjustment range ± 5 ° Fine adjustments possible with adjustment dial s24

Horizontal rotation adjustment

range

± 5 ° Fine adjustments possible with adjustment dial s24

Horizontal roll adjustment range ± 3 ° Fine adjustments possible with adjustment dial s25

Horizontal slide adjustment range ± 1.77 in.

(45 mm)

Refer to the figure

below

[Unit: in. (mm)]

9.76 (248)

17.99 (457)

9.05 (230)

8.74 (222)

6.3 (160)

9.72 (247)

0.59 (15)

4.4 (112)

8 (203.2)

3.0

(76)

1.8 (46)

4.75

(121)

1.81 (46)

Forward/backward slide adjustment range:

0 to 11.81 in. (300 mm)

Horizontal slide adjustment range:

± 1.77 in. (45 mm)

8

3. Connecting Devices

Make sure you have the power cable, computer cable, USB cable, and other parts at the location where the

setting plate is to be installed.

Make sure you have all necessary cables for any devices, such as a document camera or microphone, that you

will connect to the projector.

External speakers LAN device

Microphone

USB cable

(for Easy Interactive Function)

Document camera

Computer

Computer cable

(for computer video output)

Connection Example

Dedicated USB cable

(supplied with document camera)

Audio cable

(commercially available product)

LAN cable

Power cord

9

English

4. Positioning the Projector

The BrightLink 450Wi and PowerLite 450W can project up to 96 inches diagonally for a WXGA image or 85

inches diagonally for an XGA image. The PowerLite 460 can project up to 102 inches diagonally for an XGA

image. You can project onto a pre-installed whiteboard or directly onto a plain wall. The height of the included

wall mount determines the maximum image size and how high the image appears on the wall or whiteboard.

The distance of the projector from the wall (once it is mounted on the adjustable arm of the setting plate) also

affects image size and position.

Use the following worksheets to determine the proper location of the wall plate on the wall. If you are

projecting onto a pre-installed whiteboard, use the worksheet below. If you are projecting on a plain wall, use

the worksheet on page 10.

Installation worksheet for projecting on a pre-installed wall-mounted

board

(1) Measure the ceiling height (distance from the floor to the ceiling).

(2) Measure the height of the board’s image area (h).

(3) Measure the width of the board’s image area (w).

(4) Measure the distance from the floor to the bottom of the board’s

image area (f).

(5) Measure the distance from the ceiling to the top of the board’s image area (c).

(6) Measure the thickness of the board (x).

_____

_____ (h)

_____ (w)

_____ (f)

_____ (c)

_____ (x)

10 in. (254 mm)—height of

wall plate plus cover

Required distance from top

of image area to wall plate (b)

Diagonal size of

image area (S)

Height of

image area (h)

Distance from ceiling to

top of image area (c)

Width of image area (w)

Distance from floor to

bottom of image area (f)

10

(7) Determine the aspect ratio of the board or of the images that will be

projected. For new computers or laptops, this will most likely be WXGA

(16:10). For older equipment, this will most likely be XGA (4:3). You may need

to consult your IT director for this information.

4:3 XGA 16:10 WXGA 16:9 Widescreen

(8) Using the tables on pages 12 to 16 for your aspect ratio and desired image

height (h), find the required distance between the top of the image area and

the wall plate (b).

(9) Determine the position for your projector installation by adding the values for

(f), (h), and (b), plus an additional 10 inches for the height of the wall plate

plus the cover.

If the ceiling height of your room (as noted in step 1) does not meet the

minimum ceiling height required for your board, you may need to select a

smaller image size or move the board to a lower position on the wall.

(10)After confirming your image size, use tape or a pencil to mark the distance (b)

from the top of the image area on the board to the bottom of the wall plate.

(11)Align the line (horizontal) on the template sheet with the (b) mark, then

align the center line on the template sheet with the center of the image area.

Follow the instructions on page 18 to install the projector.

Installation worksheet for projecting on a plain wall

(1) Measure the ceiling height (distance from the floor to the ceiling).

(2) Determine the desired aspect ratio of the image. For new computers or

laptops, this will most likely be WXGA (16:10). For older equipment, this will

most likely be XGA (4:3). You may need to consult your IT director for this

information.

4:3 XGA 16:10 WXGA 16:9 Widescreen

(3) Using the tables on pages 12 to 16 for your aspect ratio, select the largest

image size available for your ceiling height.

Image height (h)

Image width (w)

(4) Determine the desired distance from the floor to the bottom of the image

area (f).

The recommended minimum distance is 30 inches. Images appearing less

than 28 inches from the floor may be obstructed for some viewers.

(5) Find the top of the projected image area by adding distances (f) and (h).

(6) Use the tables on pages 12 to 16 to determine the required distance from the

top of the image area to the bottom of the wall plate (b).

(7) Add:

Required distance from top of image area to wall plate (b)

Height of image area (h)

Distance from floor to bottom of image area (f)

Height of wall plate plus cover

If the total exceeds the ceiling height, you will need to reduce the image size

or reduce the distance from the floor to the bottom of the image area.

_____ (b)

_____ (f)

_____ (h)

_____ (b)

+10 inches

_____ total

_____

_____ (h)

_____ (w)

_____ (f)

_____

_____ (b)

_____ (h)

_____ (f)

+10 inches

_____ total

11

English

(8) After confirming your image size, use tape or a pencil to mark the distance (b) from the top of

the image area on the board to the bottom of the wall plate.

(9) Align the line (horizontal) on the template sheet with the (b) mark, then align the center

line on the template sheet with the center of the image area. Follow the instructions on page

18 to install the projector.

The tables on the following pages provide installation information for all supported image sizes. The

minimum ceiling height is based on an image 30 inches from the floor; if the image is lower, the minimum

ceiling height is reduced by the corresponding measurement.

Use the worksheets, the illustration below, and the information in the tables on the following pages to

determine the projection distance and placement of the wall plate. The recommended range for projection

distance (a) is 2.76 to 14.57 inches (7 to 37 cm).

10 in. (254 mm) —height

of wall plate plus cover

Required distance from top

of image area to wall plate (b)

Diagonal image

size (S)

Ceiling

height

Distance from ceiling to

top of image area (c)

Width of image area (w)

Distance from floor to

bottom of image area (f)

Height of

image area (h)

Wall plate

Projection surface

Offset value for the position of

the center of the screen and the

center of the wall plate

Distance from wall of projection

surface or whiteboard

2.55 in. (65 mm)

10 in. (254 mm)

12

Installation measurements in inches

Diagonal

image

size

(S)

16:10 WXGA

for BrightLink 450Wi,

PowerLite 450W, and PowerLite 460

4:3 XGA

for BrightLink 450Wi and

PowerLite 450W

16:9 Widescreen

for BrightLink 450Wi,

PowerLite 450W, and PowerLite 460

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

Projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

55” — — — — — 83.4 44.0 33.0 3.7 10.4 — — — — —

56” — — — — — 84.2 44.8 33.6 4.1 10.6 — — — — —

57” — — — — — 85.0 45.6 34.2 4.4 10.7 — — — — —

58” — — — — — 85.7 46.4 34.8 4.8 10.9 — — — — —

59” 81.2 50.0 31.3 2.7 10.0 86.5 47.2 35.4 5.2 11.1 — — — — —

60” 81.9 50.9 31.8 3.0 10.1 87.3 48.0 36.0 5.5 11.3 81.4 52.3 29.4 3.5 12.0

61” 82.6 51.7 32.3 3.3 10.3 88.0 48.8 36.6 5.9 11.5 82.1 53.2 29.9 3.9 12.2

62” 83.3 52.6 32.9 3.6 10.4 88.8 49.6 37.2 6.2 11.6 82.7 54.0 30.4 4.2 12.4

63” 83.9 53.4 33.4 4.0 10.6 89.6 50.4 37.8 6.6 11.8 83.4 54.9 30.9 4.5 12.5

64” 84.6 54.3 33.9 4.4 10.7 90.4 51.2 38.4 7.0 12.0 84.1 55.8 31.4 4.8 12.7

65” 85.3 55.1 34.4 4.6 10.9 91.1 52.0 39.0 7.3 12.1 84.8 56.7 31.9 5.2 12.9

66” 86.0 56.0 35.0 4.9 11.0 91.9 52.8 39.6 7.7 12.3 85.4 57.5 32.4 5.5 13.1

67” 86.7 56.8 35.5 5.2 11.1 92.7 53.6 40.2 8.0 12.5 86.1 58.4 32.8 5.8 13.2

68” 87.3 57.7 36.0 5.5 11.3 93.4 54.4 40.8 8.4 12.6 86.8 59.3 33.3 6.2 13.4

69” 88.0 58.5 36.6 5.9 11.4 94.2 55.2 41.4 8.8 12.8 87.4 60.1 33.8 6.5 13.6

70” 88.7 59.4 37.1 6.2 11.6 95.0 56.0 42.0 9.1 13.0 88.1 61.0 34.3 6.8 13.8

71” 89.4 60.2 37.6 6.5 11.7 95.7 56.8 42.6 9.5 13.1 88.8 61.9 34.8 7.2 14.0

72” 90.0 61.1 38.2 6.8 11.9 96.5 57.6 43.2 9.8 13.3 89.4 62.8 35.3 7.5 14.1

73” 90.7 61.9 38.7 7.1 12.0 97.3 58.4 43.8 10.2 13.5 90.1 63.6 35.8 7.8 14.3

74” 91.4 62.8 39.2 7.5 12.2 98.0 59.2 44.4 10.6 13.6 90.8 64.5 36.3 8.1 14.5

75” 92.1 63.6 39.7 7.8 12.3 98.8 60.0 45.0 10.9 13.8 91.5 65.4 36.8 8.4 14.7

13

English

* Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

76” 92.8 64.4 40.3 8.1 12.5 99.6 60.8 45.6 11.3 14.0 92.1 66.2 37.3 8.8 14.9

77” 93.4 65.3 40.8 8.4 12.6 100.3 61.6 46.2 11.7 14.1 92.8 67.1 37.8 9.1 15.0

78” 94.1 66.1 41.3 8.7 12.8 101.1 62.4 46.8 12.0 14.3 93.5 68.0 38.2 9.4 15.2

79” 94.8 67.0 41.9 9.0 12.9 101.9 63.2 47.4 12.4 14.5 94.1 68.9 38.7 9.7 15.4

80” 95.5 67.8 42.4 9.4 13.1 102.6 64.0 48.0 12.7 14.6 94.8 69.7 39.2 10.1 15.6

81” 96.2 68.7 42.9 9.7 13.2 103.4 64.8 48.6 13.1 14.8 95.5 70.6 39.7 10.4 15.8

82” 96.8 69.5 43.5 10.0 13.4 104.2 65.6 49.2 13.5 15.0 96.1 71.5 40.2 10.7 15.9

83” 97.5 70.4 44.0 10.3 13.5 104.9 66.4 49.8 13.8 15.2 96.8 72.3 40.7 11.1 16.1

84” 98.2 71.2 44.5 10.6 13.7 105.7 67.2 50.4 14.2 15.3 97.5 73.2 41.2 11.4 16.3

85” 98.9 72.1 45.0 11.0 13.8 106.5 68.0 51.0 14.5 15.5 98.2 74.1 41.7 11.7 16.5

86” 99.5 72.9 45.6 11.3 14.0 — — — — — 98.8 75.0 42.2 12.0 16.7

87” 100.2 73.8 46.1 11.6 14.1 — — — — — 99.5 75.8 42.7 12.4 16.8

88” 100.9 74.6 46.6 11.9 14.3 — — — — — 100.2 76.7 43.1 12.7 17.0

89” 101.6 75.5 47.2 12.2 14.4 — — — — — 100.8 77.6 43.6 13.0 17.2

90” 102.3 76.3 47.7 12.6 14.6 — — — — — 101.5 78.4 44.1 13.3 17.4

91” 102.9 77.2 48.2 12.9 14.7 — — — — — 102.2 79.3 44.6 13.7 17.6

92” 103.6 78.0 48.8 13.2 14.8 — — — — — 102.8 80.2 45.1 14.0 17.7

93” 104.3 78.9 49.3 13.5 15.0 — — — — — 103.5 81.1 45.6 14.3 17.9

94” 105.0 79.7 49.8 13.8 15.2 — — — — — — — — — —

95” 105.6 80.6 50.3 14.2 15.3 — — — — — — — — — —

96” 106.3 81.4 50.9 14.5 15.5 — — — — — — — — — —

Diagonal

image

size

(S)

16:10 WXGA

for BrightLink 450Wi,

PowerLite 450W, and PowerLite 460

4:3 XGA

for BrightLink 450Wi and

PowerLite 450W

16:9 Widescreen

for BrightLink 450Wi,

PowerLite 450W, and PowerLite 460

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

Projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

14

Installation measurements in millimeters

Diagonal

image

size

(S)

16:10 WXGA

for BrightLink 450Wi,

PowerLite 450W, and PowerLite 460

4:3 XGA

for BrightLink 450Wi and

PowerLite 450W

16:9 Widescreen

for BrightLink 450Wi,

PowerLite 450W, and PowerLite 460

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

Projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

55” — — — — — 2119 1118 838 94 265 — — — — —

56” — — — — — 2139 1138 853 104 269 — — — — —

57” — — — — — 2158 1158 869 113 274 — — — — —

58” — — — — — 2178 1179 884 122 278 — — — — —

59” 2063 1271 794 68 253 2197 1199 899 131 282 — — — — —

60” 2080 1292 808 76 257 2217 1219 914 140 287 2068 1328 747 90 304

61” 2098 1314 821 84 260 2236 1240 930 149 291 2085 1350 760 98 309

62” 2115 1335 835 92 264 2256 1260 945 158 295 2102 1373 772 106 314

63” 2132 1357 848 100 268 2275 1280 960 168 299 2119 1395 785 114 318

64” 2149 1379 862 108 272 2295 1300 975 177 304 2136 1417 797 123 323

65” 2167 1400 875 117 276 2314 1321 991 186 308 2153 1439 809 131 327

66” 2184 1422 888 125 279 2334 1341 1006 195 312 2170 1461 822 139 332

67” 2201 1443 902 133 283 2353 1361 1021 204 316 2187 1483 834 148 336

68” 2218 1465 915 141 287 2373 1382 1036 213 321 2204 1505 847 156 341

69” 2235 1486 929 149 291 2393 1402 1052 223 325 2221 1528 859 164 346

70” 2253 1508 942 157 294 2412 1422 1067 232 329 2238 1550 872 173 350

71” 2270 1529 956 165 298 2432 1443 1082 241 333 2255 1572 884 181 355

72” 2287 1551 969 173 302 2451 1463 1097 250 338 2272 1594 897 189 359

73” 2304 1572 983 181 306 2471 1483 1113 259 342 2289 1616 909 198 364

74” 2322 1594 996 189 309 2490 1504 1128 268 346 2306 1638 921 206 368

75” 2339 1615 1010 197 313 2510 1524 1143 277 351 2323 1660 934 214 373

15

English

* Based on an image 762 mm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

76” 2356 1637 1023 205 317 2529 1544 1158 287 355 2340 1682 946 223 378

77” 2373 1659 1037 214 321 2549 1565 1173 296 359 2357 1705 959 231 382

78” 2391 1680 1050 222 325 2568 1585 1189 305 363 2374 1727 971 239 387

79” 2408 1702 1063 230 328 2588 1605 1204 314 368 2391 1749 984 247 391

80” 2425 1723 1077 238 332 2607 1626 1219 323 372 2408 1771 996 256 396

81” 2442 1745 1090 246 336 2627 1646 1234 332 376 2425 1793 1009 264 400

82” 2459 1766 1104 254 340 2646 1666 1250 342 380 2442 1815 1021 272 405

83” 2477 1788 1117 262 343 2666 1687 1265 351 385 2459 1837 1034 281 409

84” 2494 1809 1131 270 347 2685 1707 1280 360 389 2476 1860 1046 289 414

85” 2511 1831 1144 278 351 2705 1727 1295 369 393 2493 1882 1058 297 419

86” 2528 1852 1158 286 355 — — — — — 2510 1904 1071 306 423

87” 2546 1874 1171 294 358 — — — — — 2527 1926 1083 314 428

88” 2563 1895 1185 303 362 — — — — — 2544 1948 1096 322 432

89” 2580 1917 1198 311 366 — — — — — 2561 1970 1108 331 437

90” 2597 1939 1212 319 370 — — — — — 2578 1992 1121 339 441

91” 2615 1960 1225 327 374 — — — — — 2595 2015 1133 347 446

92” 2632 1982 1239 335 377 — — — — — 2612 2037 1146 356 451

93” 2649 2003 1252 343 381 — — — — — 2629 2059 1158 364 455

94” 2666 2025 1265 351 385 — — — — — — — — — —

95” 2683 2046 1279 359 389 — — — — — — — — — —

96” 2701 2068 1292 367 392 — — — — — — — — — —

Diagonal

image

size

(S)

16:10 WXGA

for BrightLink 450Wi,

PowerLite 450W, and PowerLite 460

4:3 XGA

for BrightLink 450Wi and

PowerLite 450W

16:9 Widescreen

for BrightLink 450Wi,

PowerLite 450W, and PowerLite 460

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

Projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

16

*Based on an image 30 inches (762 mm) from the floor; if the image is lower, the minimum ceiling height is

reduced by the corresponding measurement.

4:3 XGA for PowerLite 460 in inches (and millimeters)

S w h a b

Diagonal

image size

Minimum

Ceiling Height*

Image width Image height Minimum Projection

Distance (Wide)

Distance from top of

image to wall plate

63" 84.7 (2121) 50.4 (1280) 37.8 (960) 2.8 (71) 6.9 (175)

64" 85.4 (2139) 51.2 (1300) 38.4 (975) 3.1 (79) 7.0 (177)

65" 86.1 (2156) 52.0 (1321) 39.0 (991) 3.4 (87) 7.1 (179)

66" 86.7 (2174) 52.8 (1341) 39.6 (1006) 3.7 (94) 7.1 (181)

67" 87.4 (2191) 53.6 (1361) 40.2 (1021) 4.0 (102) 7.2 (184)

68" 88.1 (2209) 54.4 (1382) 40.8 (1036) 4.3 (110) 7.3 (186)

69" 88.8 (2226) 55.2 (1402) 41.4 (1052) 4.6 (117) 7.4 (188)

70" 89.5 (2273) 56.0 (1422) 42.0 (1067) 4.9 (125) 7.5 (191)

71" 90.2 (2291) 56.8 (1443) 42.6 (1082) 5.2 (133) 7.6 (193)

72" 90.9 (2308) 57.6 (1463) 43.2 (1097) 5.5 (140) 7.7 (195)

73" 91.6 (2326) 58.4 (1483) 43.8 (1113) 5.8 (148) 7.8 (197)

74" 92.3 (2343) 59.2 (1504) 44.4 (1128) 6.1 (155) 7.9 (200)

75" 93.0 (2361) 60.0 (1524) 45.0 (1143) 6.4 (163) 8.0 (202)

76" 93.6 (2378) 60.8 (1544) 45.6 (1158) 6.7 (171) 8.0 (204)

77" 94.3 (2396) 61.6 (1565) 46.2 (1173) 7.0 (178) 8.1 (207)

78" 95.0 (2414) 62.4 (1585) 46.8 (1189) 7.3 (186) 8.2 (209)

79" 95.7 (2431) 63.2 (1605) 47.4 (1204) 7.6 (194) 8.3 (211)

80" 96.4 (2449) 64.0 (1626) 48.0 (1219) 7.9 (201) 8.4 (213)

81" 97.1 (2466) 64.8 (1646) 48.6 (1234) 8.2 (209) 8.5 (216)

82" 97.8 (2484) 65.6 (1666) 49.2 (1250) 8.5 (216) 8.6 (218)

83" 98.5 (2501) 66.4 (1687) 49.8 (1265) 8.8 (224) 8.7 (220)

84" 99.2 (2519) 67.2 (1707) 50.4 (1280) 9.1 (232) 8.8 (223)

85" 99.9 (2536) 68.0 (1727) 51.0 (1295) 9.4 (239) 8.9 (225)

86" 100.5 (2554) 68.8 (1748) 51.6 (1311) 9.7 (247) 8.9 (227)

87" 101.2 (2571) 69.6 (1768) 52.2 (1326) 10.0 (255) 9.0 (229)

88" 101.9 (2589) 70.4 (1788) 52.8 (1341) 10.3 (262) 9.1 (232)

89" 102.6 (2606) 71.2 (1808) 53.4 (1356) 10.6 (270) 9.2 (234)

90" 103.3 (2624) 72.0 (1829) 54.0 (1372) 10.9 (277) 9.3 (236)

91" 104.0 (2641) 72.8 (1849) 54.6 (1387) 11.2 (285) 9.4 (239)

92" 104.7 (2659) 73.6 (1869) 55.2 (1402) 11.5 (293) 9.5 (241)

93" 105.4 (2676) 74.4 (1890) 55.8 (1417) 11.8 (300) 9.6 (243)

94" 106.1 (2694) 75.2 (1910) 56.4 (1433) 12.1 (308) 9.7 (245)

95" 106.8 (2711) 76.0 (1930) 57.0 (1448) 12.4 (316) 9.8 (248)

96" 107.4 (2729) 76.8 (1951) 57.6 (1463) 12.7 (323) 9.8 (250)

97" 108.1 (2747) 77.6 (1971) 58.2 (1478) 13.0 (331) 9.9 (252)

98" 108.8 (2764) 78.4 (1991) 58.8 (1494) 13.3 (339) 10.0 (255)

99" 109.5 (2782) 79.2 (2012) 59.4 (1509) 13.6 (346) 10.1 (257)

100" 110.2 (2799) 80.0 (2032) 60.0 (1524) 13.9 (354) 10.2 (259)

101" 110.9 (2817) 80.8 (2052) 60.6 (1539) 14.2 (361) 10.3 (261)

102" 111.6 (2834) 81.6 (2073) 61.2 (1554) 14.5 (369) 10.4 (264)

17

English

If you have a pre-existing whiteboard, refer to the table below to identify common models and sizes. If your

board is listed here, use the dimensions to reference the installation requirements found on pages 12 to 16.

Interactive whiteboard sizes

Diagonal size 16:10 WXGA 4:3 XGA 16:9 Widescreen

60 inches — — RM ClassBoard2 60

63 inches — Hitachi® StarBoard FX-63 —

64 inches — SMART Board 660

Promethean ActivBoard 164

—

71 inches — — INTERWRITE BOARD 1071

77 inches — Hitachi Cambridge Board 77

Hitachi StarBoard FX-77

SMART Board 680

—

77.5 inches — RM ClassBoard2 77.5

INTERWRITE® BOARD 1077

—

78 inches PolyVision® TS 600/ TS610 /

TSL610/ENO 2610

PolyVision TS610

Promethean ActivBoard 178 / 378

—

82 inches — — Hitachi StarBoard FX-82W

85 inches — — INTERWRITE BOARD 1085

87 inches SMART Board™ 685

Promethean ActivBoard 387

——

93 inches — — PolyVision ENO 2810

94 inches — — SMART Board 690

96 inches Epson BrightLink 450Wi — —

18

5. Installing the Projector

Make sure to follow the steps below to install the setting plate. If you ignore these steps, the setting plate

could fall and cause personal injury or property damage.

AInstall the wall plate on the wall

(1) Determine the template sheet position.

• From the tables on pages 12 to 16, confirm the screen size (S) and the distance between the

projection surface and wall plate (b).

• Align the CTR line (vertical) of the template sheet with the center line (vertical) of the projection

surface.

Confirm where the beams or studs are within the wall, and shift the position left or right as necessary.

The position can be shifted horizontally left or right from the center line of the projection surface by

up to 1.77 in. (45 mm).

• Align the line (horizontal) of the template with the height of (b).

(2) Attach the template sheet to the wall.

If you need to install a junction box, you can use the cutout areas in the wall plate for the box.

The junction box needs to be recessed into the wall if you want to use the wall plate cover.

The maximum combined weight of the setting plate and the projector is approximately 33.5 lb

(15.2 kg). When you install the setting plate, calculate the permissible weight, carefully check

the construction, material, and strength of the wall, and perform the installation properly using

the most appropriate method.

Center line of projection surface

CTR line of template sheet

line of template sheet

65 mm (2.55 in.)

19

English

(3) Make mounting holes in the wall in the required locations.

The wall plate needs to be secured by commercially available anchors or lag bolts in the

following places. It is recommended that the wall plate be secured in at least three places.

• If securing the wall plate in four places, make the holes indicated by A or B in the figure.

• If securing the wall plate in three places, make the holes indicated by C in the figure.

(4) Remove the template sheet.

(5) Mount the wall plate on the wall.

BDetermine the projection distance and pull out the slider

(1) Using the tables on pages 12 to 16, calculate the distance (a) from the projection surface to

the front of the projector.

(2) Loosen the four screws and pull out the slider on the setting plate.

Align the slider with the mark on the slider measure that is a distance (a+x) equivalent to the

distance (a) plus the thickness of the board (x). See the tables on pages 12 to 16. The

recommended range for projection distance (a) is 2.76 to 14.57 in. (7 to 37 cm).

Four mounting holes Three mounting holes

❏When you mount the projector on the wall with the setting plate, the wall needs to be

strong enough to hold the projector and the setting plate. Confirm the weight of the

projector and the setting plate before installation, and maintain the strength of the wall. If

the wall is not strong enough, reinforce the wall before installation.

❏Install the setting plate so that it can sufficiently support the weight of the projector and

setting plate, and resist any horizontal vibration. Use M8 nuts and bolts. Nuts and bolts

smaller than M8 could cause the setting plate to fall.

❏Epson takes no responsibility for any damage or injury caused by incorrect installation.

Warning

Screws (4 )

Slider measure

20

CAttach the setting plate to the wall plate

(1) Hang the setting plate hook onto the wall plate bar (A).

(2) Lift up the setting plate and pass the cables through it (B).

(3) Tighten the two M8 x 15 mm hexagon socket head cap bolts and two M8 x 35 mm hexagon

socket head cap bolts supplied with the setting plate so that the setting plate becomes

vertical against the wall (C).

Use the two M8 x 35 mm hexagon socket head cap bolts to adjust the vertical position.

s25

DSecure the projector to the setting plate

(1) Loosen the two screws and remove the cable cover from the projector.

Take care not to trap the cables between the setting plate and wall plate.

Caution

Setting plate

Cables

Wall plate

M8 x 15 mm hexagon socket

head cap bolts (one on left

and one on right)

Wall plate bar

M8 x 35 mm hexagon

socket head cap bolts (2)

Setting plate hook

Cable cover

Screws (2)

Page is loading ...

Epson BrightLink 450Wi Installation guide

Epson BrightLink 450Wi Installation guide

in other languages

Related papers

Other documents