Trumpf STAND TKF 700 (1A1)
The Trumpf STAND TKF 700 (1A1) is a workstation designed for stationary operation of the bevelling machine TruTool TKF 700. It is used to guide small workpieces to the machine, making it easier to achieve precise and consistent results.
Capabilities:
- Securely holds workpieces: The workstation's sturdy construction and clamping system ensure that workpieces are held securely in place during machining, minimizing the risk of accidents or errors.
- Adjustable pressure die: The pressure die can be adjusted to accommodate different sheet thicknesses and chamfer sizes, allowing for versatility in processing a wide range of materials.
Trumpf STAND TKF 700 (1A1)
The Trumpf STAND TKF 700 (1A1) is a workstation designed for stationary operation of the bevelling machine TruTool TKF 700. It is used to guide small workpieces to the machine, making it easier to achieve precise and consistent results.
Capabilities:
- Securely holds workpieces: The workstation's sturdy construction and clamping system ensure that workpieces are held securely in place during machining, minimizing the risk of accidents or errors.
- Adjustable pressure die: The pressure die can be adjusted to accommodate different sheet thicknesses and chamfer sizes, allowing for versatility in processing a wide range of materials.
Operator's manual
English
STAND TruTool TKF 700 (1A1)
2 Table of contents E552EN_03.DOC
Table of contents
1. Safety ..................................................................................3
2. Description .........................................................................4
2.1 Intended use ........................................................................4
2.2 Technical data .....................................................................4
3. Setting work .......................................................................5
3.1 Installing the workstation .....................................................5
3.2 Mounting and aligning the machine in the
workstation...........................................................................6
4. Operation............................................................................8
5. Maintenance .......................................................................9
6. Replacement parts.............................................................9
E552EN_03.DOC Safety 3
1. Safety
¾ Read the Operator's Manual for the machine as well as that of
the pedestal, in addition to the safety information (Material
number 125699), in their entirety and follow precisely the
instructions contained therein before starting up the machine.
¾ Adhere to the safety regulations in accordance with DIN VDE,
CEE, AFNOR and to the specific regulations of the country of
operation.
Warning
Risk of injury if the workstation tips over!
¾ Fasten the workstation securely on the table.
Warning
Risk of injury through crushing of the hand!
¾ Hold workpiece with both hands.
¾ Do not place hands in the tool parts.
4 Description E552EN_03.DOC
2. Description
2.1 Intended use
The workstation is used for stationary operation of the bevelling
machine TruTool TKF 700:
• Guide small workpieces to the machine.
The use of the TruTool TKF 700 machine is described in the
Operator's manual.
2.2 Technical data
Values
Weight (without machine) Approx. 19.5 kg
Working height Approx. 160 mm
Total height with machine Approx. 250 mm
Technical data
Table 1
E552EN_03.DOC Setting work 5
3. Setting work
3.1 Installing the workstation
¾ Attach the workstation to the table with 4 screws.
Fig. 42162
6 Setting work E552EN_03.DOC
3.2 Mounting and aligning the machine in
the workstation
46 50 41 45 47 130 110 55 40 48 49 42
52
Position
40
41
42
45
46
47
48
49
50
52
55
110
130
Designation
Trestle
Strip, right
Strip, left
Plate
Clamping levers (2x)
Cap screw M 5x10-12 DIN 912
Lock nut (knurled nut) (2x)
Star grip
Disc ISO 7090-8-ST A2F
Cap screw M 5x16-12 DIN 912
Swarf box
Hand protection
Cap screw M 8x60-12 DIN 912
Tension spring
Material number
133885
133883
133884
133886
105652
014524
133947
133948
0147198
014540
138911
134674
015059
135309
Workstation (optional, Order number 977764)
Fig. 15497
E552EN_03.DOC Setting work 7
1. Rotate the machine carrier into the correct position.
2. Fasten the machine in the workstation with the help of the
screw (110) (wrench can be found among the accessories).
3. Loosen the two clamping levers (46).
4. The plate (45) in which the machine is held can be adjusted
only by turning the star grips (49).
5. This will cause the pressure die to be repositioned in relation to
the strips (41) and (42). (Pressure die = hardened support
piece on which the sheet edge to be machined is slid along
during the work process).
6. Set chamfer size and sheet thickness at the two knurled nuts
(31) and (34) on the machine.
ca. 0-0.5 mm
41 29 42
29 Pressure die
41 Strips
42 Strips
Setting value of the machine pressure die in relation to
the strips at the workstation
7. Pressure die min. 0, max. 0.5 mm above the support area of
the strips (41) (42).
8. It should be noted that the plate (45) is repositioned parallel to
the strips (41) (42).
9. Lay flat part of sheet with straight edge on the strips (41) (42).
10. Turn star grip (49) until the pressure die is up against the sheet
edge.
11. Turn both star grips (49) by approximately 1/4 of a revolution
further to the right, respectively, and lock with the knurled
counter nut (48).
12. Clamp the plate (45) tightly with the two clamping levers (46).
13. The workpiece will lie on the plate (45).
Note
Hold the work piece during machining in such a way that the
surface lies on the plate (45) and the sheet edge lies on the strips
(41) (42).
Fig. 13403
8 Operation E552EN_03.DOC
4. Operation
Warning
Risk of possible injury from sharp blades!
¾ Do not reach into the area which is covered over by the hand
protection device.
¾ Do not reach into the space between the workpiece and the
plate.
The machining of small workpieces in the workstation
1. Place the workpiece outside the machine on the plate.
2. Push the workpiece up against the strip.
3. Guide the workpiece slowly through the machine.
Fig. 15496
E552EN_03.DOC Maintenance 9
5. Maintenance
Warning
Danger of injury due to improper repairs!
The device will then not function properly.
¾ Repair work may only be carried out by a qualified specialist.
Note
Only use original replacement parts and observe the information
on the rating plate.
6. Replacement parts
To ensure the correct and quick delivery of original parts and
wearing parts:
1. Specify the order number.
2. Enter further order data:
– Voltage data
– Number of pieces
– Machine type
3. Specify the complete shipping information:
– Correct address.
– Required delivery type (e.g. air mail, courier, express mail,
ordinary freight, parcel post).
4. Send the order to your TRUMPF representative. Refer to the
address list at the end of the document for TRUMPF service
addresses.
Ordering replacement parts
10 Replacement parts E552EN_03.DOC
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Trumpf STAND TKF 700 (1A1)
The Trumpf STAND TKF 700 (1A1) is a workstation designed for stationary operation of the bevelling machine TruTool TKF 700. It is used to guide small workpieces to the machine, making it easier to achieve precise and consistent results.
Capabilities:
- Securely holds workpieces: The workstation's sturdy construction and clamping system ensure that workpieces are held securely in place during machining, minimizing the risk of accidents or errors.
- Adjustable pressure die: The pressure die can be adjusted to accommodate different sheet thicknesses and chamfer sizes, allowing for versatility in processing a wide range of materials.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Trumpf TruTool TKF 1500 (1B1) User manual
-
-
-
-
-
-
-
-
-
