VEVOR 4400 LBS Engine Hoist Leveler User manual

Type
User manual
Technical Support and E-Warranty Certificate www.vevor.com/support
4400 LBS ENGINE HOIST
USER'S MANUAL
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and doses not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
- 1 -
Have product questions? Need technical support? Please feel free to
contact us:
CustomerService@vevor.com
NEED HELP? CONTACT US!
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our
user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again if
there are any technology or software updates on our product.
4400 LBS
ENGINE HOIST
- 2 -
SPECIFICATION
ITEM
CAPACITY
N.W(kg)
XXJD11002B
4400
71.4
INSPECTION
Inspect the equipment carefully before each use. Ensure the
equipment is not damaged, excessively worn, or missing parts.
Do not use the equipment unless it is properly lubricated.
Using equipment that is not in good clean working condition or properly
lubricated may cause serious injury.
Inspect the work area before each use. Make sure it is free and clear of
any potential hazards.
DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING
THIS MANUAL.
To maintain the equipment and user safety, the responsibility of the
owner is to read and follow these instructions.
Inspect the equipment for proper operation and function.
Keep instructions readily available for equipment operators.
Make certain all equipment operators are properly trained; understand
how to safely and correctly operate the unit.
Allow unit operation only with all parts in place and operating properly.
Use only genuine replacement parts.
Service and maintain the unit only with authorized or approved
replacement parts; negligence will make the equipment unsafe for
use and void the warranty.
Carefully inspect the unit on a regular basis and perform all maintenance
as required.
Store these instructions in the handle of your equipment.
Keep all decals on the unit clean and visible.
- 3 -
WARNING!
1. Study, understand, and follow all instructions before operating this
device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces, with less than 3 degrees of slope.
4. Mount and support only on areas of the engine as specified by the
vehicle manufacturer.
5. No alterations shall be made to this product.
6. Only attachments and/or adapters supplied by the manufacturer shall
be used.
7. Never work directly under a supported load.
8. Do not use this product for any use other than the manufacturer
specified usage.
9. Failure to heed these markings may result in personal injury and/or
property damage.
MAINTENANCE INSTRUCTIONS
Maintain your equipment. It is recommended that the general condition
of any equipment be examined before it is used. Keep your equipment
in good repair by adopting a program of conscientious repair and
maintenance. Have necessary repairs made by qualified service
personnel.
Follow the maintenance instructions carefully to keep your equipment in
good working condition. Never perform any maintenance on the
equipment while it is under a load.
a. All moving parts of the equipment should be regularly cleaned.
b. Lubricate parts as required by the manufacturer’s specifications. The
type of lubricant should be as specified by the manufacturer or a qualified
person. Lubrication systems should be checked to verify proper operation.
c. If additional maintenance is required, it should be completed in
accordance with the instructions of the manufacturer or qualified person.
- 4 -
Binding
If the product binds while under a load, use equipment with equal or a
larger load capacity to lower the load safely to the ground. After un-binding;
clean, lubricate and test that equipment is working properly. Rusty
components, dirt, or worn parts can be causes of binding Clean and
lubricate the equipment as indicated in the lubrication section. Test the
equipment without a load. If the binding continues, contact Customer
Service.
IF YOUR EQUIPMENT BINDS
As your equipment becomes older, the threads may start binding. This will
prevent the equipment from operating properly and safely. Rusty threads,
dirty threads, or a worn threads can cause binding. Clean and lubricate the
equipment. Test the equipment without a load. If the binding continues,
refer to the after sale parts and service. If your equipment binds while
under a load, use equipment with equal or larger load capacity to lower the
load safely to the ground.
Cleaning
If the moving parts of the equipment are obstructed, use cleaning solvent
or another good degreaser to clean the equipment. Remove any existing
rust, with a penetrating lubricant.
Do not use motor oil to lubricate the equipment
Rust Prevention:
- Check daily for any signs of rust or corrosion. Without a load check for
signs of rust that are visible and clean as needed.
Storing the Equipment
1. Store in a dry location, recommended indoors.
2. Equipment should be stored in an area where they will not be subjected
to damage.
3. If extreme temperatures or chemically active or abrasive environments
are involved, the guidance provided in shall be
followed.
4. Temperature - When equipment are to be used at temperatures above
- 5 -
140"F (60"C) or below -20"F (-29"C), the
equipment manufacturer or a qualified person should be consulted.
5. Chemically Active Environments -The strength and operation of
equipment can be affected by chemically active environments such as
caustic or acid substances or fumes. The equipment manufacturer or a
qualified person should be consulted before equipment are used in
chemically active environments.
6. Other Environments - The internal workings of equipment can be
affected by high moisture, gravel or sand, silt, grit, or other dust-laden air.
Equipment subject to these environments should have their inner
components frequently cleaned, inspected, and lubricated.
Note: If the equipment is stored outdoors, be sure to lubricate all parts
before and after use to ensure the equipment stays in good working
condition.
ASSEMBLY INSTRUCTIONS
1. Attach caster assembly(21) to base assembly (20) with bolt (22),
washer(23)spring washer (24) and nut (25). Attach caster assembly(28)
to base assembly (20) with bolt (29), washer(23)spring washer (24) and
nut (25). Attach caster assembly(21) to front leg(34) with bolt (22),
washer(23)spring washer (24) and nut (25).
2. Insert front leg(34)to the base assembly(20). Lift one side of the front
leg(34) to align the hole on front leg(34) to the hole on the for base
assembly(20), then insert the lock pin (26) into the hole , and insert the
R Pin27) into the hole of lock pin.
3. Attach Support rod (18) to the base assembly (20) with bolt (30),
washer (31), spring washer(32) and nut (33).
4. Attach pull plate(17) to the support rod (18)and base assembly (20) with
bolt (2), washer (3), spring washer(4) and nut (5).
5. Attach jack(19) to Support rod (18) with bolt (2), washer(3)spring
washer (4) and nut (5).
6. Attach main derrick(1) to Support rod (18) with bolt (42),washer(3)spring
- 6 -
washer (4) and nut (5).
7. Lift one side of the main derrick(1) to align the hole on the jack(19) to
the hole on the for main derrick(1) , then insert the bolt (10) into the
hole , and fasten it with washer (3), spring washer(4) , nut (5).
8. Insert telescopic rod(41) into proper position of the main derrick(1).
Line up the hole in the main derrick(1) and the hole of telescopic
rod(41), then insert the bolt (6) into the hole , and fasten it with washer
(31), spring washer(32) , nut (33).
9. Attach chain hook (35) to the telescopic rod(42) with bolt (14), washer
(15) and nut (16).
10. Attach two hanging jaw(39) to lock Pin(26),And fasten it to engine
Leveler(36) with bolt(37).Repeat the above steps to fasten anther two
hanging jaw(39) to engine Leveler(36).
11. Attach engine leveler assembly to the chain hook (35).
12. Tight all the screws.
- 7 -
ASSEMBLY DIAGRAM
Item
Name
Qty.
Item
Name
Qty.
1
Main Derrick
1
22
Hex Head Bolt M8x15mm
16
2
Hex Head Bolt
M16x100mm
4
23
Washer M8
24
3
Washer M16
6
24
Spring Washer M8
24
4
Spring Washer M16
6
25
Nut M16
24
5
Nut M16
6
26
Lock Pin
4
6
Hex Head Bolt M14x90mm
1
27
R Pin
20
7
/
28
Caster Assembly 3.0"
2
8
/
29
Cross Flat Head Bolt
M8x20mm
8
9
/
30
Hex Head Bolt M14x100mm
2
10
Hex Head Bolt M16x75mm
1
31
Washer M14
3
11
/
32
Spring Washer M14
3
12
/
33
Nut M14
3
13
/
34
Front Leg
2
14
Hex Head Bolt M12x75mm
1
35
Chain Hook
1
15
Washer M12
1
36
Engine Leveler
1
16
Nut M12
1
37
Bolt M8x30
2
17
Pull Plate
2
38
Lock Ring
2
18
Support Rod
1
39
Hanging Jaw
4
19
Jack
1
40
Pressure Rod
1
20
Base Assembly
1
41
Telescopic Rod
1
21
Caster Assembly 3.3"
4
42
Hex Head Bolt M16x120mm
1
- 8 -
- 9 -
FOLDING STORAGE
After use the equipment,you can fold the legs to save space.shown as the
figure.
- 10 -
Importer: WAITCHX
Address: 250 bis boulevard Saint-Germain 75007 Paris
Importer: FREE MOOD LTD
Address: 2 Holywell Lane, London, England, EC2A 3ET
REP
UK
EUREP UK LTD
UNIT 2264, 100 OCK STREET, ABINGDON
OXFORDSHIRE ENGLAND OX14 5DH
REP
EC
EUREP GmbH
Unterlettenweg 1a, 85051
Ingolstadt, Germany
Manufacturer: Haiyan Xinxing Mechanical And Electrical. Co., Ltd
AddressLiuzhuang Village Xitang qiao Street Haiyan County Zhejiang
Province
Made In China
Technical Support and E-Warranty Certificate
www.vevor.com/support
Made In China
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

VEVOR 4400 LBS Engine Hoist Leveler User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI