YAESU FT-710 User manual

Brand: YAESU

Model: FT-710

Type: User manual

Operation Manual

FT-710

About this Manual

The FT-710 is a leading-edge transceiver with a number of new and exciting features, some of which may

be unfamiliar to you. In order to gain the most enjoyment and operating eciency from the FT-710, we

recommend that you read this manual in its entirety, and keep it handy for reference as you explore the

many capabilities of this new transceiver.

Before using the FT-710, be sure to read this manual.

How to read this operation manual

Two methods are used to select an item displayed on the FT-710 Function Screen: “Operate by touch-

ing the item directly on the display”; and “Turn the [FUNC] knob to select the item and then press

the [FUNC] knob”.

Subsequently, in this manual, the operations that can be performed either by touching the Function

Screen, or by turning and pressing the [FUNC] knob are abbreviated to “Select [DISPLAY SETTING] →

[DISPLAY] → [LED DIMMER]”; as described in the following:

Example: How to adjust the brightness of the LED

1. Press the [FUNC] knob to display the function screen.

2. Touch [DISPLAY SETTING] on the function screen, or rotate the [FUNC] knob to select [DISPLAY

SETTING] and then press the [FUNC] knob.

3. Touch [DISPLAY] on the display or rotate the [FUNC] knob to select [DISPLAY] and then press the

[FUNC] knob.

4. Touch the setting section of [LED DIMMER] on the display, or rotate the [FUNC] knob to select [LED

DIMMER] and then press the [FUNC] knob.

5. Rotate the [FUNC] knob, or touch “<” or “>” on either side of the value to adjust the brightness.

The following notations are also used in this manual:

This icon indicates cautions and alerts the user should be aware of.

This icon indicates helpful notes, tips and information.

Table of Contents

General Description ........................................ 4

Safety Precautions .........................................6

Accessories & Options ...................................8

Installation and Interconnections ....................9

Antenna Considerations ..................................... 9

Antenna Connections ......................................... 9

Power Cable Connections .................................. 9

Microphone, Headphone, Key, Keyer and

FH-2 Connections ............................................ 10

Linear Amplier Interconnections ..................... 11

VL-1000 Linear Amplier Interconnections .... 11

Display connections ......................................... 12

Remote operation (LAN unit “SCU-LAN10”)

connection ........................................................ 12

AESS (Acoustic Enhanced

Speaker System) ..........................................13

SP-40 connections ........................................... 13

Rear Panel....................................................14

TUNER/LINEAR ....................................... 14

ANT ........................................................... 14

GND .......................................................... 14

EXT SPKR ................................................ 14

REM/ALC .................................................. 14

KEY........................................................... 14

RTTY/DATA .............................................. 14

USB .......................................................... 14

USB Jack .................................................. 14

EXT-DISPLAY ........................................... 14

DC IN ........................................................ 14

SSM-75E Microphone Switches ...................15

Display Indications........................................16

Meter Display ............................................ 17

Operation MODE Display ......................... 17

Operation status Display .......................... 17

HI-SWR Display ........................................ 17

Frequency Display (VFO-A) ..................... 18

Keyboard Frequency Entry ...................... 18

Tuning in 1 MHz or 1 kHz Steps ............... 18

Frequency Display (VFO-B) ..................... 18

When the clarier function is active .......... 18

Operation of the display [FUNC] knob ...... 19

Filter Function Display .............................. 20

Turn the spectrum display OFF ................ 20

Information displayed on the

scope screen ............................................ 20

Important Receiver Settings ..................... 21

ATT (Attenuator) ....................................... 21

IPO ........................................................... 21

DNF (Digital NOTCH Filter) ...................... 21

AGC (Automatic Gain Control) ................. 21

Information displayed on

the scope screen ...................................... 22

Scope Display Setting .............................. 22

CENTER/CURSOR/FIX ........................... 22

CENTER................................................... 22

CURSOR .................................................. 22

FIX ............................................................ 23

3DSS ........................................................ 23

MULTI ....................................................... 23

EXPAND ................................................... 24

SPAN ........................................................ 24

SPEED ..................................................... 24

Set with the FUNC knob ........................... 25

LEVEL ...................................................... 25

PEAK ........................................................ 25

MARKER .................................................. 26

COLOR..................................................... 26

Adjust contrast.......................................... 26

Adjusting the brightness (DIMMER) ......... 26

Other display settings ........................................ 27

Screen Saver ................................................. 27

Inputting the Call Sign ................................... 27

Front Panel Controls & Switches .................. 30

ON/OFF (LOCK) Switch ........................... 30

SD memory card slot ................................ 30

TUNE ........................................................ 30

VOX/MOX ................................................. 30

Adjusts the VOX GAIN ............................. 30

Adjusts the VOX Delay Time .................... 30

Adjusts the VOX anti-trip sensitivity ......... 31

PHONES Jack .......................................... 31

MIC ........................................................... 31

MAIN dial .................................................. 31

WIRE STAND ........................................... 31

STEP •MCH / ............................... 32

DSP interference removal functions ......... 32

1. SHIFT ................................................... 33

2. WIDTH.................................................. 33

3. NOTCH................................................. 33

4. CONTOUR ........................................... 34

Adjusting the GAIN of the

CONTOUR Circuit ................................ 34

Sets the Bandwidth (“Q”) of the

CONTOUR Circuit ................................ 34

5. APF....................................................... 34

DSP RESET ............................................. 34

DNR (Digital Noise Reduction) ................. 35

Adjusting the DNR Level ........................... 35

A/B ............................................................ 35

BAND (

Operating Band Selection

) ................ 35

QMB (Quick Memory Bank) ...................... 35

QMB Channel Storage ............................. 35

QMB Channel Recall ................................ 35

Changing the number of QMB channels .. 35

VMI (VFO mode indicator) ........................ 36

BUSY/TX indicator .................................... 36

NAR (Narrow) ........................................... 36

FINE/FAST................................................ 36

RF GAIN/SQL ........................................... 37

Switching the operation of the

[RF GAIN/SQL] knob ................................ 37

AF GAIN ................................................... 37

MODE (Operating Mode Selection) .......... 37

ZIN/SPOT ................................................. 38

SPLIT ........................................................ 38

CLAR (Clarier) ........................................ 38

RX Clarier ............................................... 38

Adjust transmit frequency to the

oset frequency ........................................ 38

TX Clarier ............................................... 39

To oset the frequency with the

TX Clarier Adjust receive frequency ....... 39

NB ............................................................. 39

Adjusting the Noise Blanker Level ........... 39

Adjusting the Noise Attenuation ............... 39

Reduces longer duration pulse noise ....... 39

Voice Communications (SSB and AM) .........40

When transmitting in SSB or AM mode ............ 40

Set with the FUNC knob ................................... 40

Speech Processor ............................................ 41

RF Power output control ................................... 41

MONI (Monitor) ................................................. 41

Parametric Microphone Equalizer .................... 42

Setup the ...................................................... 42

Parametric Microphone Equalizer ................. 42

Activate the ................................................... 42

Parametric Microphone Equalizer ................. 42

Voice Memory ................................................... 44

Record the received audio ............................... 45

Play the recorded content ............................. 45

Erase the recorded content ........................... 45

Adjustable Receiver Audio Filter ...................... 46

Change the sound quality of the

received audio .................................................. 47

Using the Automatic Antenna Tuner ................. 48

CW Mode Operation ..................................... 49

Adjusting the Sidetone Audio level ................ 49

CW Delay Time Setting ................................. 49

CW Spotting (Zero-Beating) ............................. 49

Setting of the Electronic Keyer ......................... 50

Adjusting the Keyer Speed ............................ 50

Setting the Keyer Weight (Dot/Dash) Ratio ... 50

Reversing the Keyer Polarity ......................... 50

Selecting the Keyer Operating Mode ............ 50

Contest Memory Keyer ..................................... 51

Message Memory .......................................... 51

Storing a Message into Memory .................... 51

Message Memory Programming ................... 51

(Using your Paddle) ....................................... 51

Checking the CW Memory Contents ............. 52

On-The-Air CW Message Playback .............. 52

TEXT Memory ............................................... 53

Text Memory Storage .................................... 53

Text Message Programming .......................... 53

Checking the CW Memory Contents ............. 54

On-The-Air CW Message Playback .............. 54

FM Mode Operation......................................55

Repeater Operation .......................................... 55

Tone Squelch Operation ................................... 55

DATA (FT8 / RTTY / PSK) Operation ............ 56

Connecting to a Personal Computer ................ 56

FT8 operation ................................................... 57

RTTY Operation ............................................... 58

PSK Operation ................................................. 58

Memory Operation ........................................ 60

►

V ......................................................... 60

Moving Memory Data to the

VFO register ............................................. 60

Transfer last used memory to VFO .......... 60

V/M ....................................................... 60

Memory Storage ....................................... 60

Recall a Memory Channel other than

the last used VFO frequency .................... 61

Memory Tune Operation........................... 61

Memory Groups........................................ 61

Choosing the Desired Memory Group ...... 61

Erasing Memory Channel Data ................ 62

Check Memory Channel Status................ 62

Labeling Memories ................................... 62

Displaying the Memory Tag ...................... 62

Scan Skip Setting ..................................... 63

60-Meter (5 MHz) Band

(U.S. and U.K. Version only) .................... 63

VFO and Memory Scanning .........................64

VFO/Memory Scan ........................................... 64

Programmable Memory Scan (PMS) ............... 65

Other Functions ............................................66

Band Stack Operation ...................................... 66

TOT (Time Out Timer) ...................................... 66

Operation on Alaska Emergency Frequency:

5167.5kHz (U.S. Version Only) ........................ 66

Screen capture ................................................. 67

Using the SD Card ........................................... 68

Formatting a SD card .................................... 68

Saving Memory data and Setting Menu data

.. 69

Reading Memory and Set Menu data ............ 70

Display the SD Card Information ................... 70

Setting Menu ................................................71

Optional Accessories ..................................100

FC-40 External Automatic Antenna Tuner

(for Wire Antenna) .......................................... 100

Active-Tuning Antenna System (ATAS-120A)

.. 102

FH-2 Remote Control Switches ...................... 103

Carrying Handle MHG-1 ................................. 104

Mounting Bracket SMB-209 ........................... 104

Resetting the Microprocessor ..................... 105

Specications .............................................106

Index ........................................................... 108

YAESU LIMITED WARRANTY ................... 110

Display the Certications of

FCC and CANADA ..................................... 112

General Description

SDR receiver circuit designed with emphasis on fundamental performance

The high-resolution A/D converter and the FPGA element developed for the high-end SDR Yaesu Trans-

ceivers are utilized. The twin A/D converter circuit conguration performs digital conversion processing

using two A/D converters and FPGA digital synthesis. A/D converter overow due to overload is reduced

to improve blocking characteristics. In addition, random noise is added to the analog signal before digital

conversion, and by minimizing the quantization error during digital conversion by the A/D converter, distor-

tion is suppressed. Then Dithering technology is implemented to improve IM (intermodulation) character-

istics, etc., and enhance the overall performance of the SDR receiver circuit.

3DSS method adopted

In addition to the conventional waterfall display, a 3DSS (3 Dimensions Spectrum Stream) image method

has been adopted. The 3DSS image uses the horizontal axis (X axis) for frequency, the vertical axis (Y

axis) for signal intensity, and the Z axis for time. Compared to the conventional waterfall method, the sig-

nal strength is displayed in three dimensions as well as in color, recognition of changes in the band condi-

tions is instant, convenient and intuitive.

AESS (Acoustic Enhancement Speaker System) produces high-delity Audio

Using DSP signal processing, the speaker in the top of the Transceiver, and an external side speaker are

combined to reproduce high-quality received audio with a wide frequency range and a three-dimension-

al eect that would not be expected from a compact HF transceiver. set the optimum sound quality by

adjusting the output balance and frequency characteristics of the two speakers according to your prefer-

ence.

High-brightness TFT full-color display with touch-panel functionality

The FT-710 is equipped with a 4.3-inch full-color TFT display. Operating functions, including the receiving

band noise and signal interference reduction tools, are graphically displayed. Even while involved in rig-

orous operations, such as DXpeditions and contests, the operator may instantly grasp the status of each

function.

Filter Function Display monitors the status of the passband

In the upper part of the display, a lter function display presents the state of the pass-band. In addition to

the operating state of the interference removal functions, the lter function information is displayed. Not

only can you grasp the operating status of WIDTH, SHIFT, NOTCH and CONTOUR at a glance, you can

also view the status of the RF spectrum in the passband.

Two selectable RF Stages amplify the desired signals from low band to

high band

RF amplifier AMP1, and AMP2 are low noise negative feedback RF amplifiers that may be selected or

combined in series as is needed for various low-band, high-band, frequency and noise conditions.

In addition, the IPO (Intercept Point Optimization) function maximizes the dynamic range and enhances

the close multi-signal and inter-modulation characteristics of the receiver. The inuence of strong broad-

casting stations, especially in the low bands, can be minimized.

WIDTH and the continuously variable Bandwidth SHIFT features per-

mit elimination of interfering signals

The WIDTH feature allows the bandwidth to be narrowed by rotating the WIDTH knob. The SHIFT feature,

can eliminate interference in one side of the passband. Often, weak signals disappear due to interfering

signals (including pile-ups). The interfering signals may be extracted, leaving only the desired signal, be-

cause of the unique DSP sharp ltering characteristics.

CONTOUR feature is renowned for eective noise reduction

Rather than using the DSP extremely sharp attenuation characteristics, the CONTOUR circuit provides

gentle shaping of the DSP passband lter, and can thus attenuate or peak bandwidth components in seg-

ments. The interfering signal can be naturally shaped without having part of the signal suddenly disrupted.

The contour function is very eective in making the desired signal rise out of the interference.

DNR (Digital Noise Reduction) by DSP digital processing

The incorporated digital noise reduction circuit may be set to the optimal working algorithm by varying the

15 step parameters according to the noise type.

NOTCH feature can eliminate an unwanted heterodyne, and the DNF

feature can instantly attenuate multiple heterodyne signals

When interfering beat signals are present in the receiver passband, the IF NOTCH feature can signicant-

ly eliminate a narrow portion of the passband and remove the interfering signal. Moreover, when there are

multiple interfering signals, the DSP DNF (Digital Notch Filter) Automatic Tracking System can be eec-

tive, even when an interfering frequency is changing.

[FUNC] (function) knob

Simply press the function [FUNC] knob to easily select the setting menu, and then change the setting val-

ue. Quick response is possible even while operating. Assign a frequently used function or setting menu

and then you can easily change the setting just by turning the knob.

VMI (VFO mode indicator)

The VMI is placed on the left and right sides of the MAIN dial to show the current operating status of

VFO-A, VFO-B, Memory mode and clarier/split operation.

The color of the VMI indicator may be selected from 4 colors (blue/green/red/white) for each operation

status.

SD memory card

An SD card slot on the left side of the front panel permits using a commercially available SD memory card

for recording/playback of received audio, for voice recording for transmission, to save the various oper-

ating settings, saving memory contents, and screen capture (saving the display screen). The SD card is

also used to update the rmware.

Safety Precautions

Note beforehand that the company shall not be liable for any damages suered by the customer or third

parties in using this product, or for any failures and faults that occur during the use or misuse of this prod-

uct, unless otherwise provided for under the law.

Type and meaning of the marks

DANGER This mark indicates an imminently hazardous situation, which, if not avoided, could result in

death or serious injury.

WARNING This mark indicates a potentially hazardous situation, which, if not avoided, could result in

death or serious injury.

CAUTION This mark indicates a potentially hazardous situation, which, if not avoided, may result in minor

or moderate injury or only property damage.

Type and meaning of symbols

Prohibited actions that must not be attempted, in order to use this radio safely.

For example, signifies that disassembly is prohibited.

Precautions that must be adhered to in order to use this radio safely. For example, signifies that the power

supply is to be disconnected.

DANGER

Do not use the device in “regions or aircrafts

and vehicles where its use is prohibited” such

as in hospitals and airplanes.

This may exert an impact on electronic and med-

ical devices.

Do not operate the device when flammable

gas is generated.

Doing so may result in fire and explosion.

Do not use this product while driving or riding

a motorbike. This may result in accidents.

Make sure to stop the car in a safe location first

before use if the device is going to be used by

the driver.

When an alarm goes off with the external an-

tenna connected, cut off the power supply to

this radio immediately and disconnect the ex-

ternal antenna from this radio.

If not, this may result in fire, electric shock and

equipment failure due to thunder.

Do not transmit in crowded places in consid-

eration of people who are fitted with medical

devices such as heart pacemakers.

Electromagnetic waves from the device may af-

fect the medical device, resulting in accidents

caused by malfunctions.

Do not touch any liquid leaking from the liquid

display with your bare hands.

There is a risk of chemical burns occurring when

the liquid comes into contact with the skin or gets

into the eyes. In this case, seek medical treat-

ment immediately.

Never touch the antenna during transmission.

This may result in injury, electric shock and equip-

ment failure.

WARNING

Do not use voltages other than the specified

power supply voltage.

Doing so may result in fire and electric shock.

Do not transmit continuously for long periods

of time.

This may cause the temperature of the main body

to rise and result in burns and failures due to

overheating.

Do not dismantle or modify the device.

This may result in injury, electric shock and equip-

ment failure.

Do not handle the power plug and connector

etc. with wet hands. Also do not plug and un-

plug the power plug with wet hands.

This may result in injury, liquid leak, electric shock

and equipment failure.

Do not use fuses other than those specified.

Doing so may result in fire and equipment failure.

When smoke or strange odors are emitted

from the radio, turn off the power and discon-

nect the power cord from the socket.

This may result in fire, liquid leak, overheating,

damage, ignition and equipment failure. Please

contact our company customer support or the re-

tail store where you purchased the device.

Keep the power plug pins and the surround-

ing areas clean at all times.

This may result in fire, liquid leak, overheating,

breakage, ignition etc.

Disconnect the power cord and connection

cables before incorporating items sold sepa-

rately and replacing the fuse.

This may result in fire, electric shock and equip-

ment failure.

Never cut off the fuse holder of the DC power

cord.

This may cause short-circuiting and result in igni-

tion and fire.

Do not allow metallic objects such as wires

and water to get inside the product.

This may result in fire, electric shock and equip-

ment failure.

Do not place the device in areas that may get

wet easily (e.g. near a humidifier).

This may result in fire, electric shock and equip-

ment failure.

When connecting a DC power cord, pay due

care not to mix up the positive and negative

polarities.

This may result in fire, electric shock and equip-

ment failure.

Do not use DC power cords other than the one

enclosed or specified.

This may result in fire, electric shock and equip-

ment failure.

Do not bend, twist, pull, heat and modify the

power cord and connection cables in an un-

reasonable manner.

This may cut or damage the cables and result in

fire, electric shock and equipment failure.

Do not pull the cable when plugging and un-

plugging the power cord and connection ca-

bles.

Please hold the plug or connector when unplug-

ging. If not, this may result in fire, electric shock

and equipment failure.

Refrain from using headphones and ear-

phones at a loud volume.

Continuous exposure to loud volumes may result

in hearing impairment.

Do not use the device when the power cord

and connection cables are damaged, and

when the DC power connector cannot be

plugged in tightly.

Please contact our company customer support or

the retail store where you purchased the device

as this may result in fire, electric shock and equip-

ment failure.

Follow the instructions given when installing

items sold separately and replacing the fuse.

This may result in fire, electric shock and equip-

ment failure.

Do not use the device when the alarm goes

off.

For safety reasons, please pull the power plug of

the DC power equipment connected to the prod-

uct out of the AC socket.

Never touch the antenna as well. This may result

in fire, electric shock and equipment failure due

to thunder.

CAUTION

Do not place this device near a heating instru-

ment or in a location exposed to direct sun-

light.

This may result in deformation and discoloration.

Do not place this device in a location where

there is a lot of dust and humidity.

Doing so may result in fire and equipment failure.

Stay as far away from the antenna as possible

during transmission.

Long-term exposure to electromagnetic radiation

may have a negative effect on the human body.

Do not wipe the case using thinner and ben-

zene etc.

Please use a soft and dry piece of cloth to wipe

away the stains on the case.

Keep out of the reach of small children.

If not, this may result in injuries to children.

Do not put heavy objects on top of the power

cord and connection cables.

This may damage the power cord and connection

cables, resulting in fire and electric shock.

Do not transmit near the television and radio.

This may result in electromagnetic interference.

Do not use optional products other than those

specified by our company.

If not, this may result in equipment failure.

When using the device in a hybrid car or fu-

el-saving car, make sure to check with the car

manufacturer before using.

The device may not be able to receive transmis-

sions normally due to the influence of noises from

the electrical devices (inverters etc.) fitted in the

car.

Do not turn on the volume too high when us-

ing a headphone or earphone.

This may result in hearing impairment.

For safety reasons, switch off the power and

pull out the DC power cord connected to the

DC power connector when the device is not

going to be used for a long period of time.

If not, this may result in fire and overheating.

Do not throw or subject the device to strong

impact forces.

This may result in equipment failure.

Do not the put this device near magnetic cards

and video tapes.

The data in the cash card and video tape etc. may

be erased.

Do not place the device on an unsteady or

sloping surface, or in a location where there

is a lot of vibration.

The device may fall over or drop, resulting in fire,

injury and equipment failure.

Do not stand on top of the product, and do not

place heavy objects on top or insert objects

inside it.

If not, this may result in equipment failure.

Do not use a microphone other than those

specified when connecting a microphone to

the device.

If not, this may result in equipment failure.

Accessories & Options

Supplied Accessories

External Speaker SP-40 Hand Microphone SSM-75E DC Power Cord

Spare Fuse (25A)

• Operation Manual • World Map • Sticker

Available options

• Hand Microphone (equivalent to the supplied microphone) SSM-75E

• Reference Microphone M-1

• Dual Element Microphone M-100

• Desktop Microphone M-90D

• Microphone Stand Kit M-90MS

• Desktop Microphone M-70D

• Lightweight Stereo Headphone YH-77STA

• External Automatic Antenna Tuner FC-40

• Active Tuning Antenna (Automatic Type) ATAS-120A

• Antenna Base Kit (for ATAS-120A) ATBK-100

• Active Tuning Antenna (Manual Type) ATAS-25

• Remote Control Keypad FH-2

• LAN Unit SCU-LAN10

• Mounting Bracket SMB-209

• Carrying Handle MHG-1

• Packet Cable CT-39A

• VL-1000 Linear Amplier Connection Cable CT-58

Installation and Interconnections

Antenna Considerations

The FT-710 is designed to connect to a 50 Ohm resistive impedance antenna at the Amateur operating

frequencies. Select an appropriate antenna (dipole antenna, YAGI antenna, cubical quad antenna, etc.)

that is suitable for the chosen operation and bands.

Construct the antenna and coaxial cable, or use a suitable antenna tuner, to maintain the impedance

presented to the FT-710 antenna connector for an SWR of 1.5 or less. Careful preparation of the antenna

and/or tuner will permit maximum performance, and protect the transceiver from damage.

High transmitter RF voltages may be present on the antenna; install it so it will not be easily touched when

in operation.

Antenna Connections

Carefully follow the illustration regarding the proper connection of antennas and coaxial cables.

To prevent damage from lightning, atmospheric electrical discharges,

electric shock etc., provide a good earth ground.

Use a short, thick, braided cable to connect the station equipment to the

buried ground rod (or alternative earth ground system).

Power Cable Connections

Carefully follow the illustrations regarding the proper connection of the DC power cable.

Use the DC power cable supplied with the FT-710 to make the power connections to the power supply.

RED

FUSE: 25A

Check the DC voltage and current rating

(+13.8 V, 25 A) of the power supply before

connecting to the transceiver.

DC power cord (supplied)

BLACK

Installation guidelines

• Ensure adequate ventilation around the trans-

ceiver, to prevent heat build-up and possible re-

duction of performance due over heating.

• Do not install the transceiver in a mechanically

unstable location, or where objects may fall onto

it from above.

• To minimize the possibility of interference to

home entertainment devices, take all precaution-

ary steps including separation of TV/FM anten-

nas from Amateur transmitting antennas to the

greatest extent possible. Keep the transmitting

coaxial cables separated from cables connected

to home entertainment devices.

• The AC Power Cord connected to a socket-out-

let with earthing connection. A socket-outlet with

earthing connection shall connect to protective

earthing conductor.

Microphone, Headphone, Key, Keyer and FH-2 Connections

①

②

③

④

⑤

⑥

⑦

⑧

DOWN

+5V

MIC GND

MIC

PTT

GND

FAST

①

⑧

φ3.5mm

Remote Control Keypad

FH-2 (option)

External Speaker

SP-40

(as viewed from front panel)

Key-up voltage is approximately +5.0V DC, and key-down current is approximately 3mA.

Linear Amplier Interconnections

Be sure that both the FT-710 and VL-1000 are turned OFF, and then follow the installation recommendations

contained in the bellow illustration.

• VL-1000 Linear Amplier Interconnections

• Refer to the VL-1000 Operating Manual for details regarding amplier operation.

• Do not attempt to connect or disconnect coaxial cables when your hands are wet.

• Set the Setting Menu item “TUN/LIN PORT SELECT” to “LINEAR” (page 89).

• Since the ALC cable is connected to the REM/ALC jack, the optional FH-2 cannot be connected.

DC IN

ANT

ALC 1BAND-DATA 1 GND

CONTROL

DC 48V IN

ANT 1

ANT 2

ANT 3

INPUT 1

Coaxial Cable (50 ohm)

Connect to “INPUT 1” of the VL-1000

HF/50MHz Antenna

REM/ALC

GND

TUNER/LINEAR

“CT-58” ALC Cable (option)

“CT-58” Band Data Cable (option)

Display connections

The video digital output of the FT-710 transceiver can be shown on a large monitor. Use a commercially

available DVI-D cable to connect a display monitor directly to the “EXT-DISPLAY” terminal (DVI-D) on the

back of the FT-710.

The DVI-D cable can be used with either single link or dual link.

EXT-DISPLAY

DVI-D Cable

DVI-D

Remote operation (LAN unit “SCU-LAN10”) connection

Operate the transceiver from a remote location. Use the optional LAN unit “SCU-LAN10” to connect

the FT-710 to a LAN or the Internet, then use the PC control software that can be downloaded from the

Yaesu website. In addition to the basic remote operation of the transceiver, the LAN unit supports moni-

toring the various scope displays, so you can operate comfortably. In addition to remote operation from a

remote location, you can connect to your home LAN and monitor the band status on a large display from

a convenient location away from the ham shack.

In addition to transmitted and received audio, the RF scope and AF scope can be remoted, so comfort-

able remote communication can be performed while easily setting and tuning the band status display,

making various lter settings, interference removal function, etc. are possible using the scope function

from a personal computer.

LAN

DC-IN

Internet

LAN Network Remote control PC

Remote control

SCU-LAN10

(option)

AESS (Acoustic Enhanced Speaker System)

The combination of the internal speaker on top of the transceiver with the external speaker

“SP-40”, reproduces high-quality received audio with a wide frequency range and a three-dimensional

acoustic eect. Set the optimum sound quality by adjusting the output balance and frequency characteris-

tics of the two speakers according to your preference.

• The AESS is designed to function optimally with the included speaker “SP-40”. It will not perform properly

with other speakers.

• When moving or transporting the FT-710, remove the SP-40 to prevent it from falling o.

SP-40 connections

The SP-40 can be mounted on either the left or right side of the transceiver.

remove

Supplied washers and screws

Connect the speaker cable to the

“EXT SPKR” terminal on the rear panel.

• Change the output balance of the

two speakers

1. Press the [FUNC] knob.

FUNC knob

2. Touch [AESS].

3. Rotate the [FUNC] knob to adjust the output

balance of the two speakers, according to

your liking. It is recommended to use it at

around 50%.

• Change the frequency characteristics

1. Press the [FUNC] knob.

FUNC knob

2. Touch [AESS-CF].

3. Rotate the [FUNC] knob to select the cutoff

frequency from “700Hz” and “1000Hz”.

Normally, 700Hz is a balanced sound quality,

but when listening at a loud volume, set it to

1000Hz.

Rear Panel

TUNER/LINEAR

This 8-pin output

jack is used to con-

nect to the FC-40

External Automatic

Antenna Tuner or a

Linear Amplier.

Refer to the table below for the BAND DATA termi-

nal levels when using a linear amplier.

BAND BAND DATA BAND BAND DATA

A B C D A B C D

400k H L H H 18 L H H L

1 L H H H 21 H H H L

1.8 H L L L 24.5 L L L H

3.5 L H L L 28 H L L H

5 / 7 H H L L 50 L H L H

10 L L H H 70 H H H H

14 H L H L

ANT

Connect the main antenna here, using type-M (PL-

259) connectors and coaxial feed lines. The internal

antenna tuner aects only the antenna connected

here, and only during transmission.

GND

Use this terminal to connect the transceiver to a

good earth ground, for safety and optimal perfor-

mance.

EXT SPKR

This 3.5-mm, 2-contact, jack

provides audio output for a

external loudspeaker “SP-

40”. The impedance at the

jack is 4-8 Ohms.

REM/ALC

By plugging the FH-2 Remote Control Keypad into

this jack, direct access to the FT-710 CPU is pro-

vided for control functions of the contest memory

keying, and also frequency and function control.

When a device such as a linear amplifier is con-

nected, this is an external ALC current input jack.

EXT ALC

TX REQ

GND

Set menu item “TUN/LIN PORT SELECT” to “LINEAR”.

REMOTE

GND

Set menu item “TUN/LIN PORT SELECT” to other than

“LINEAR”.

SIGNAL GND

KEY

This 3.5-mm, 3-contact jack accepts a CW key or

keyer paddle. A two-contact plug cannot be used

in this jack. Key-up voltage is +5.0V DC, and key-

down current is 3mA.

KEY

GND

When connecting a single straight key

DOT

DASH

COMMON

When connecting an electronic keyer paddle

RTTY/DATA

This 6-pin input/output jack accepts AFSK input

from a Terminal Node

Controller (TNC); it also

provides xed level receiv-

er audio output, and FSK

keying line.

USB

Connecting to a computer from this jack with a

commercially available USB cable allows remote

control by CAT commands from a computer. The

jack can also be used for input and output of audio

signals and transmitter control. A USB driver is re-

quired for remote control from a computer. Down-

load the driver from the Yaesu website (http://www.

yaesu.com).

USB Jack

Connect a USB A type keyboard or mouse. They

can be used to select items on the screen or to en-

ter characters.

EXT-DISPLAY

DVI-D connector for connecting an external moni-

tor.

When using an external monitor, set the setting

menu item “EXT DISPLAY” to “ON”.

Connect a monitor that supports 800 x 480

resolution or 800 x 600 resolution.

DC IN

This is the DC power supply connection for the

transceiver.

Use the supplied DC cable to

connect directly to a DC power

supply, which must be capable

of supplying at least 25 A @13.8

VDC.

DATA IN

PTT SHIFT

GND

DATA OUT SQL

RESET（BAND D）

TX INH BAND C

RX D(BAND B)

TX D(BAND A)

TX GND

+13V OUT

GND

SSM-75E Microphone Switches

PTT Switch

Switches Transmit/Receive.

Press to transmit and release to receive.

DWN / UP Key

The [UP]/[DWN] keys may also be used to manual-

ly scan the frequency upward or downward.

● The amount of frequency change depends on the

operation mode (default setting: see table below).

Operating Mode UP DWN

LSB / USB / CW-L / CW-U +20

-20Hz

DATA-L / DATA-U

RTTY-L / RTTY-U / PSK

+10Hz

-10Hz

AM / AM-N / FM / FM-N

DATA-FM / D-FM-N +5kHz -5kHz

● The frequency change can be changed in the

setting menu.

Operating Mode Menu Item Step

LSB / USB

CW-L / CW-U

SSB/CW DIAL STEP

5/10/20 (Hz)

DATA-L / DATA-U

RTTY-L / RTTY-U

PSK

RTTY/PSK DIAL STEP

AM / AM-N AM CH STEP

2.5/5/9/10/

12.5/25

(kHz)

FM / FM-N

DATA-FM

D-FM-N

FM CH STEP

5/6.25/10/

12.5/20/25

(kHz)

MUTE Key

While pressing the MUTE key, the receiver audio

from the speaker will be muted.

Microphone

Speak into the microphone in a normal tone of

voice with the microphone 5cm away from the

mouth.

MUTE

P1 P2 P3 P4

P1 key

This key toggles the ON/OFF lock for the MAIN Dial

knob. When “Lock” is ON, the MAIN Dial knob can

still be turned, but the frequency will not change,

and “LOCK” appears in the display.

It is the same function as the [LOCK] key on the

front panel of the transceiver.

P2 key

The current operation status can be stored in a

dedicated memory channel (QMB: Quick Memory

Bank) with one touch.

It is the same function as the [QMB] key on the

front panel of the transceiver.

P3 key

Pressing this key momentarily, exchanges the

VFO-A and VFO-B frequency data.

It is the same function as the [A/B] key on the front

panel of the transceiver.

P4 key

This key toggles frequency control between VFO

and the memory system.

It is the same function as the [V/M ] key on the

front panel of the transceiver.

The functions of the [P1] / [P2] / [P3] / [P4] / [UP] / [DWN] keys can be assigned by the following operations:

1. Press the [FUNC] knob.

2. Select [OPERATION SETTING] → [GENERAL].

3. Select a key to assign a function [MIC P1] / [MIC P2] / [MIC P3] / [MIC P4] / [MIC UP] / [MIC DOWN].

4. Rotate the [FUNC] knob, or touch “<” or “>” on either side of the value to select a function (see the table below)

5. Touch [BACK] several times to return to normal operation.

LOCK

QMB

A/B

V/M

TUNER

VOX/MOX

MODE

ZIN SPOT

SPLIT

: Toggles the ON/OFF lock for the MAIN

Dial knob.

: QMB (Quick Memory Bank) function.

: Swaps the VFO-A and VFO-B frequency

data.

: Toggles frequency control between VFO

and the memory system.

Turns the built-in antenna tuner ON/OFF

: Press to turn the VOX function ON/OFF.

Press and hold to activate the MOX

function.

: Change the operation mode.

: Press to activate the auto-zero function.

Press and hold to activate the sidetone.

: SPLIT function.

FINE

NAR

DNR

FREQ UP

FREQ DOWN

BAND UP

BAND DOWN

ATT

IPO

DNF

AGC

: Sets the ne tuning ON/OFF.

: Sets the Narrow ON/OFF.

: Activates the NB (Noise blanker) func-

tion.

: Activates the DNR (Digital Noise Reduc-

tion) function.

: Change to a higher frequency.

: Change to a Lower frequency.

: Change to a higher Operation Band.

: Change to a Lower Operation Band.

: Turns the ATT (Attenuator) ON/OFF.

: Activates the IPO.

: Turns the DNF (Digital Notch Filter) ON/

OFF.

: Adjust the AGC receiver-recovery time.

Display Indications

It operates as an S meter in receive. In transmit, select the desired meter from: PO,

COMP, ALC, VDD, ID, and SWR.

Displays the current operation mode.

In VFO mode, “VFO-A” or “VFO-B” is displayed. In memory mode, the type and chan-

nel number of the recalled memory are displayed.

This display warns of an abnormality in the antenna system. If it lights up, check the

antenna system immediately.

Displays the transmit/receive frequency of Main-band.

Displays the transmit/receive frequency of Sub-band. While the clarifier function is

operating, the oset (dierence between the receive frequency and the transmit fre-

quency) is displayed.

The functions that operate when the [FUNC] knob is turned are displayed.

Displays the passband status of the Digital lter.

Displays the mode, the sweep speed, and span width (display range) of the scope

screen.

Displays the setting status of assorted important receiver operations. The setting can

be changed by touching it.

The icon of the operating function lights up.

Touch the scope screen keys to switch the display mode of the screen between the

3DSS display and waterfall display, to display the oscilloscope and AF-FFT, to switch

the display area of the scope screen, to set the frequency span (display range), or to

switch the sweep speed.

Meter Display

S-Meter

RF power Output

When the meter display screen is touched, the

transmit meter selection screen is shown (the

default setting is “PO”).

RF power Output

Standing Wave Ratio Final amplifier

drain voltage

Final amplifier drain current

AMC gain control display

(Displays compression level during

speech processor operation)

Make adjustments by pressing the [FUNC] knob

→

touch [COMP] → rotate the [FUNC] knob.

Relative ALC voltage

Touch the meter area

Operation MODE Display

Displays the current operating mode. When

touched the operation mode selection screen is

displayed. Touch the desired operation mode to

select it.

Touch [PRESET] to display the settings that ap-

ply to the FT8 operation.

Operation status Display

VFO-A: Lights in VFO-A mode.

VFO-B: Lights in VFO-B mode.

M-xx: Displays the selected channel number in

memory mode.

MT: Lights up during memory tuning operation.

QMBxx: Lights up during operation with quick memory.

M-Pxx: Lights up during programmable memory scan

operation.

EMG: Emergency call set frequency call lights up.

HI-SWR Display

This is a warning notification of an

abnormality in the antenna system.

If “HI-SWR” lights up, immediately check if for

any abnormality in the antenna system.

Frequency Display (VFO-A)

Displays the transmit and receive frequencies of

VFO-A. Press the [A/B] key to switch between

VFO-A and VFO-B, the frequency of VFO-B is

displayed.

• Keyboard Frequency Entry

1. Touch the “Hz” area of the frequency display.

2. Enter the frequency using the numeric keys.

Clear all entered numbers.

The entered frequency is

confirmed.

The display returns to the

previous screen when

back is touched.

Erases the rightmost digit.

● If there is no operation within 10 seconds,

the input will be canceled.

3. Touch [ENT] to conrm.

● A short-cut for frequencies ending in zero -

touch [ENT] after the last non-zero digit.

Example:

To enter 7.00.000MHz

[0] → [7] → [ENT] or [7] → [.] → [ENT]

To enter 7.03.000MHz

[7] → [.] → [0] → [3] → [ENT]

• Tuning in 1 MHz or 1 kHz Steps

To temporarily set the dial knob to 1MHz or 1kHz

steps, touch the “MHz” or “kHz” area of the fre-

quency display.

Touch “MHz” or “kHz” area of the frequency dis-

play to confirm. If there is no operation within 3

seconds, the frequency will be xed.

Touch the Scope Screen, to easily move to the

touched frequency.

Frequency Display (VFO-B)

Displays the transmit and receive frequencies of

VFO-B. Press the [A/B] key to switch between

VFO-B and VFO-A, the frequency of VFO-A is

displayed.

When the clarier function is active, the oset fre-

quency is displayed.

• When the clarier function is active

The clarier is used to adjust the transceiver re-

ceive frequency to match the other station trans-

mit frequency and improve the audio; or to shift

the transmit frequency of this station when the

transmit frequency of the contact station is shift-

ed.

CLAR RX

：

CLAR TX

：

CLAR RXTX

： •

•

Changes only the receive frequency while

leaving the transmit frequency as it is.

Changes only the transmit frequency while

leaving the receive frequency as it is.

After changing the receive frequency with

the clarifier, pressing the [CLAR] key twice

will set the transmit frequency to match the

receive frequency.

After changing the transmit frequency with

the clarifier, pressing the [CLAR] key will

set the receive frequency to match the

transmit frequency.

When the receive frequency is offset by +20 Hz.

Press the [CLAR] key, the display will show “CLAR

RX” in red and the clarier will be active.

Rotate the DIAL knob to change the offset fre-

quency of the clarier.

To cancel Clarifier operation, press the [CLAR]

key several times.

Page is loading ...

YAESU FT-710 User manual

YAESU FT-710 User manual

Related papers

Other documents