TM
TM
TM
ENTER
TO WIN
www.facebook.com/simplihomefurnishings
PART DESCRIPTION
5/23
E
F
NEED HELP? For help with assembly or if you are missing a part,
Please call customer service at 1-866-518-0120 ext. 262 (9 am to 4 pm EST)
G
H
I J K
PART DESCRIPTION
6/23
NEED HELP? For help with assembly or if you are missing a part,
Please call customer service at 1-866-518-0120 ext. 262 (9 am to 4 pm EST)
DRAWER BOTTOM SUPPORT
QTY 1
HARDWARE DESCRIPTION
7/23
2
4
Required -
Flathead screwdiver
Phillips screwdriver
Not Included
a. M4 X 25mm - QTY 1
b. M4 X 15mm - QTY 1
c. M4 X 25mm - QTY 1
CAM LOCK PIN
CAM LOCK
QTY 23 SETS
FURNITURE ANTI-TIPPING
RESTRAINT
QTY 1 SET
COMPONENTS-KEY DIAGRAM MODEL # 3AXCRED-05
G
D
F
E
H
C
P
M
O
K
J
K
L
K
I
N
K
B
AL
AR
ASSEMBLY MODEL # 3AXCRED-05
1. Attach four Cam Lock Pins 9 to back of Small Drawer Front I .
2. Align Cam Lock Pins with pre-drilled holes and attach Drawer Sides K .
3. Insert two Cam Lock 9 into pre-drilled holes on each Drawer Side K .
4. Use flathead screwdriver to secure Cam Locks.
K
K
I
9
k
k
N
I
ASSEMBLY MODEL # 3AXCRED-05
1
2
K
L
K
N
10
I
ASSEMBLY MODEL # 3AXCRED-05
1. Attach five Cam Lock Pins 9 to back of Large Drawer Front J .
2. Align Cam Lock Pins with pre-drilled holes and attach Drawer Sides K .
3. Insert two Cam Lock 9 into pre-drilled holes on each Drawer Side K .
4. Use flathead screwdriver to secure Cam Locks.
K
K
J
9
9
J
K
K
O
ASSEMBLY MODEL # 3AXCRED-05
1. Align Cam Lock Pins with pre-drilled holes and attach Drawer Bottom Support P .
2. Insert one Cam Lock 9 into pre-drilled holes on Drawer Bottom Support P .
3. Use flathead screwdriver to secure Cam Locks.
4. Attach Large Drawer Back M to Drawer Bottom Support P using two Phillips
screws 11 .
5. Use Phillip Screwdriver to snugly tighten screw.
6. Align Large Drawer Back M with Large Drawer Bottom O and press firmly into slot.
7. Attach Large Drawer Back M using two Allen Key Screws 1 through pre-drilled
holes on each Side K .
8. Use Allen Key 2 to tighten Screws. Do not over-tighten.
K
2
1
M
11
O
9
P
ASSEMBLY MODEL # 3AXCRED-05
10
J
ASSEMBLY MODEL # 3AXCRED-05
1. Attach Divider D to Top Shelf H using three Allen Key Screws 1 .
2. Use Allen Key 2 to tighten. Do not over-tighten.
1
2
D
H
9
H
C
2
1
AL
ASSEMBLY MODEL # 3AXCRED-05
1. Repeat Step-10 for Side AR .
9
H
C
1
2
AR
ASSEMBLY MODEL # 3AXCRED-05
1. Attach Top B to Side AR , AL and Divider D using nine Allen Key Screws 1
(three screws on each Side and Divider).
2. Use Allen Key 2 to tighten screws. Do not over-tighten.
1
2
2
1
B
D
AL
AR
ASSEMBLY MODEL # 3AXCRED-05
6
B
G
G
AL
NOTE: The screwdriver is not
included in the hardware pack.
ASSEMBLY MODEL # 3AXCRED-05
4
8
E
D
7
5
7
5
AR
ASSEMBLY MODEL # 3AXCRED-05
D
E
F
F
3
3
3
AR
12
12
NOTE: The screwdriver is not
included in the hardware pack.
Page is loading ...
Page is loading ...
Page is loading ...
/