Sakrete.com • 866-725-7383
The Pro’s Choice Since 1936
Curing:
Allow to air-cure for 72 hours prior to traffic.
Precautions:
Air, mix and substrate temperatures should be between 50°F (10°C) and 90°F
(32°C) and no rain in the forecast within 24 hours of application. For applications
outside this range of temperatures and conditions, contact Sakrete Technical
Service.
• Colder temperatures or higher humidity conditions will retard set times.
• Protect from freezing for 48 hours
NOTE: Proper application and installation of all Sakrete products are the responsibility of the end user.
Safety:
READ and UNDERSTAND the Safety Data Sheet (SDS) before using this product.
WARNING: Wear protective clothing and equipment. For emergency information,
call CHEMTREC at 800-424-9300 or 703-527-3887 (outside USA).
KEEP OUT OF REACH OF CHILDREN.
Limited Product Warranty:
The manufacturer warrants that this product shall be of merchantable quality
when used or applied in accordance with the manufacturer’s instructions. This
product is not warranted as suitable for any purpose other than the general
purpose for which it is intended. This warranty runs for one (1) year from the
dates the product is purchased. ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO
THE DURATION OF THIS WARRANTY. Liability under this warranty is limited to
replacement or defective products or, at the manufacturer’s option, refund of the
purchase price. CONSEQUENTIAL AND INCIDENTAL DAMAGES ARE NOT RECOV-
ERABLE UNDER THIS WARRANTY.
Concrete Repair
Sakrete
®
Concrete Repair is a siliconized acrylic latex
for filling cracks in concrete.
Features:
• Weather resistant - fills and seals cracks
• Paintable after curing
Use For:
• Repairing cracks from 1/8” to 3/8” (3.2 to 9.5 mm) wide in concrete slabs
Yield/Coverage:
Technical Data:
DIVISION 7
Joint sealants - 07 92 00
Color:
Gray
Preparation/Application:
For best results all materials should be stored between 50
0
F (10
0
C) and 80
0
F
(27
0
C) 24 hours prior to installation.
1. Clean cracks using a garden hose and/or putty knife removing all debris
from crack.
2. Cracks should be at least 1/8” (3.2 mm) wide. Using a chisel widen crack as
needed.
3. Deep cracks should be filled with sand to within 3/8” (9.5 mm) of the sur-
face.
4. Cut tube nozzle to desired bead width and puncture seal at the inside base
of the tip.
5. Squeeze Concrete Repair into the crack using a standard caulking gun.
6. Smooth and trim off excess caulk with a moist putty knife or trowel while
material is still wet.
SAKRETE
®
and the background design are registered trademarks of SAKRETE of North America LLC, Charlotte, NC 28217 • ©2006. SAKRETE
®
is manufactured under license from SAKRETE of North America LLC.
For current and complete product information, contact SAKRETE Technical Services toll-free at 866-725-7383 or visit Sakrete.com.
Rev. 06/16
Tube Size Yield
5.5 fl oz tube (304 mL) 1/4” x 1/4” x 12.5 ft (6.4 x 6.4 x 3.8 m) long
10.3 fl oz tube (304 mL) 1/4” x 1/4” x 25 ft (6.4 x 6.4 x 7.6 m) long
-
1
SAKRETE 65450021 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
SAKRETE 363701193 Installation guide
-
-
-
-
-
-
-
-
-
