Supermicro H8SGL-F User manual

Category
Server/workstation motherboards
Type
User manual

This manual is also suitable for

H8SGL
H8SGL-F
USER’S MANUAL
Revision 1.0d
®
SUPER
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0d
Release Date: November 23, 2010
Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2010 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America
Preface
iii
Preface
About This Manual
This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use of the
H8SGL(-F) serverboard.
The H8SGL(-F) serverboard is based on the AMD® SR5650/SP5100 chipset
and supports one AMD Socket G34 type processor with up to 128 GB of DDR3-
1333/1066/800 registered ECC SDRAM or 32 GB of DDR3-1333/1066/800 MHz
unbuffered ECC/non-ECC SDRAM. The H8SGL serverboard does not have IPMI
capability, whereas the H8SGL-F serverboard does.
Please refer to the motherboard speci cations pages on our web site for updates on
supported processors (http://www.supermicro.com/aplus/). This product is intended
to be professionally installed.
Manual Organization
Chapter 1 includes a checklist of what should be included in your motherboard
box, describes the features, speci cations and performance of the motherboard
and provides detailed information about the chipset.
Chapter 2 begins with instructions on handling static-sensitive devices. Read this
chapter when installing the processor(s) and memory modules and when installing
the motherboard in a chassis. Also refer to this chapter to connect the hard disk
drives, the various ports, and the power and reset buttons and the system LEDs.
If you encounter any problems, see Chapter 3, which describes troubleshooting
procedures for the video, the memory and the setup con guration stored in CMOS.
For quick reference, a general FAQ (Frequently Asked Questions) section is
provided. Instructions are also included for contacting technical support. In addition,
you can visit our web site for more detailed information.
Appendix A provides BIOS Error Beep Code Messages.
Appendix B lists BIOS POST Checkpoint Codes.
iv
H8SGL(-F) Serverboard User’s Manual
Notes
v
Table of Contents
Chapter 1 Introduction
1-1 Overview ............................................................................................................ 1
Checklist ............................................................................................................. 1
1-2 Contacting Supermicro ....................................................................................... 2
H8SGL(-F) Quick Reference .............................................................................. 5
1-3 Chipset Overview ............................................................................................. 10
AMD SR5650/SP5100 Processor .................................................................... 10
HyperTransport Technology ............................................................................. 10
1-4 PC Health Monitoring ....................................................................................... 10
1-5 Power Con guration Settings............................................................................11
1-6 Power Supply ................................................................................................... 12
1-7 Super I/O .......................................................................................................... 12
Chapter 2 Installation
2-1 Static-Sensitive Devices ..................................................................................... 1
Precautions ........................................................................................................ 1
Unpacking .......................................................................................................... 1
2-2 Processor and Heatsink Installation................................................................... 2
2-3 Mounting the Motherboard into a Chassis ......................................................... 4
2-4 Installing Memory ............................................................................................... 4
DIMM Module Population Con guration ....................................................... 6
2-5 PCI Expansion Cards ......................................................................................... 7
2-6 I/O Port and Control Panel Connections ........................................................... 8
Front Control Panel ............................................................................................ 8
2-7 Connector De nitions ........................................................................................ 9
Power Connectors ........................................................................................ 9
PW_ON Connector ........................................................................................ 9
Reset Connector ........................................................................................... 9
Overheat/Fan Fail LED (OH)......................................................................... 9
NIC2 (LAN2) LED ........................................................................................ 10
NIC1 (LAN1) LED ........................................................................................ 10
HDD LED ..................................................................................................... 10
Power On LED ............................................................................................ 10
NMI Button .................................................................................................. 10
LAN1/2 (Ethernet Ports) .............................................................................. 10
Universal Serial Bus Ports ...........................................................................11
USB Headers ...............................................................................................11
Table of Contents
vi
Fan Headers .................................................................................................11
Serial Ports ...................................................................................................11
SGPIO ......................................................................................................... 12
Chassis Intrusion ........................................................................................ 12
Overheat LED .............................................................................................. 12
Wake-On-LAN ............................................................................................. 12
Power I2C .................................................................................................... 12
Power LED/Speaker .................................................................................... 13
ATX PS/2 Keyboard and PS/2 Mouse Ports ............................................... 13
IPMB ............................................................................................................ 13
Video Connector .......................................................................................... 13
Compact Flash Card PWR Connector ........................................................ 14
2-8 Jumper Settings ............................................................................................... 14
Explanation of Jumpers ................................................................................... 14
CMOS Clear ................................................................................................ 14
I2C to PCI-Express Slot .............................................................................. 15
VGA Enable/Disable .................................................................................... 15
LAN1/2 Enable/Disable .............................................................................. 15
Onboard Speaker Enable/Disable ............................................................... 15
Compact Flash Master/Slave Select ........................................................... 16
Watch Dog Enable/Disable ......................................................................... 16
USB Wake-Up ............................................................................................ 16
BMC Jumper ............................................................................................... 16
2-9 Onboard Indicators ........................................................................................... 17
LAN1/LAN2 LEDs ........................................................................................ 17
Dedicated IPMI LAN LEDs .......................................................................... 17
Power LED .................................................................................................. 17
2-10 IDE and SATA Drive Connections .................................................................... 18
IDE Connector ............................................................................................. 18
SATA Ports .................................................................................................. 18
2-11 Enabling SATA RAID ........................................................................................ 19
Serial ATA (SATA)............................................................................................. 19
Installing the OS/SATA Driver .......................................................................... 19
Building a Driver Diskette ............................................................................ 19
Enabling SATA RAID in the BIOS .................................................................... 20
Using the Adaptec RAID Utility ........................................................................ 21
Installing the RAID Driver During OS Installation ............................................ 21
2-12 Installing Drivers ............................................................................................... 22
Supero Doctor III .............................................................................................. 23
H8SGL(-F) Serverboard User’s Manual
Table of Contents
vii
Chapter 3 Troubleshooting
3-1 Troubleshooting Procedures .............................................................................. 1
Before Power On ............................................................................................... 1
No Power ........................................................................................................... 1
No Video ............................................................................................................ 2
Memory Errors .................................................................................................. 2
Losing the System’s Setup Con guration .......................................................... 2
3-2 Technical Support Procedures ........................................................................... 3
3-3 Frequently Asked Questions .............................................................................. 3
3-4 Returning Merchandise for Service.................................................................... 4
Chapter 4 BIOS
4-1 Introduction ......................................................................................................... 1
4-2 Main Menu ......................................................................................................... 2
4-3 Advanced Settings Menu ................................................................................... 2
4-3 Security Menu .................................................................................................. 14
4-4 Boot Menu ........................................................................................................ 15
4-5 Exit Menu ......................................................................................................... 16
Appendix A BIOS Error Beep Codes
Appendix B BIOS POST Checkpoint Codes
B-1 Uncompressed Initialization Codes .................................................................... 1
B-2 Bootblock Recovery Codes ................................................................................ 2
B-3 Uncompressed Initialization Codes .................................................................... 3
Notes
viii
H8SGL(-F) Serverboard User’s Manual
Chapter 1: Introduction
1-1
Chapter 1
Introduction
1-1 Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
One (1) H8SGL(-F) serverboard
One (1) I/O shield (MCP-260-00027-0N)
One (1) Retention bracket (BKT-0035L)
One (1) 9-pin serial port cable (CBL-0010L)
One (1) ATA 66/100 IDE LP cable (CBL-0036L-03)
Six (6) 2ft. Amphenol, SATA cable (CBL-0044L)
One (1) CD containing drivers and utilities
1-2
H8SGL(-F) Serverboard User’s Manual
1-2 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Paci c
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3991
Web Site: www.supermicro.com.tw
Technical Support:
Tel: 886-2-8228-1366, ext.132 or 139
Chapter 1: Introduction
1-3
Figure 1-1. H8SGL(-F) Image
1-4
H8SGL(-F) Serverboard User’s Manual
Notes:
Jumpers not indicated are for test purposes only.
Not all ports, jumpers or LED Indicators are available on all serverboards.
Figure 1-2. H8SGL(-F) Motherboard Layout
(not drawn to scale)
JPW1
JPI2C1
JF1
JPW2
JWF1
IPMB
SATA5SATA4SATA3SATA2SATA1SATA0
JWOL
JD1
JCF1
JOH1
JI2C1
JI2C2
JL1
DP3
BATTERY
JBT1
JPL1
JPL2
JPUSB1
JPG1
JWD
FAN2
FAN1
FAN6
FAN5
FAN3FAN4
DIMM4B
DIMM4A
DIMM3B
DIMM3A
DIMM2B
DIMM2A
DIMM1B
DIMM1A
T-SGPIO1T-SGPIO2
IDE#1
CPU
USB2
USB3
SLOT6 PCI-E 2.0 x8 (in x16)
SLOT5 PCI-E 2.0 X8
USB6/7USB4/5
SLOT3 PCI 33MHz
SLOT2 PCI 33MHz
SLOT1 PCI 33MHz
LAN2
LAN1
COM2
CMOS CLEAR
COM1
VGA
LAN IPMI/
USB0/1
KB/
Mouse
SLOT4 PCI-E 2.0 x4 (in x8)
AMD
SR5100
AMD
SR5650
Winbond
WPCCM450
BMC
JPB
Chapter 1: Introduction
1-5
H8SGL(-F) Quick Reference
Jumper Description Default Setting
JBT1 CMOS Clear (See Section 2-7)
JCF1 Compact Flash Master/Slave Closed (Master)
JD1 Power LED
Pins 1-3: Power LED
Pins 4-7: Speaker
JI
2
C1/JI
2
C2 I
2
C to PCI-E Slot Enable/Disable Both Closed (Enabled)
JPB BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1 LAN 1 Enable/Disable Pins 1-2 (Enabled)
JPL2 LAN 2 Enable/Disable Pins 1-2 (Enabled)
JPUSB1 USB Power
Pins 1-2: Dual Power
Pins 2-3: Standalone Power
JWD Watch Dog Pins 1-2 (Reset)
LED Description
LAN Ports LEDs for the LAN Ethernet ports
Dedicated IPMI LAN LEDs for the dedicated IPMI LAN Ethernet port (H8SGL-F only)
DP3 LED for Serverboard Power-On
1-6
H8SGL(-F) Serverboard User’s Manual
Connector Description
COM1/COM2 COM1 Serial Port/Header
FAN 1-6 Chassis/CPU Fan Headers
IDE#1 IDE Disk Drive Connector
IPMB System Management Bus Header for the IPMI Slot
IPMI LAN Dedicated IPMI LAN Port (H8SGL-F only)
JD1 Speaker Header
JF1 Front Panel Connector
JL1 Chassis Intrusion Header
JOH1 Overheat Warning Header
JPI2C1 Power I
2
C Header
JPW1 24-pin Main ATX Power Connector
JPW2 +12V 8-pin CPU Power Connectors
JWF1 Compact Flash Card Power Connector
JWOL Wake-On-LAN Header
LAN1/2 Gigabit Ethernet (RJ45) Ports
PS2 Mouse/Keyboard PS2 Mouse/Keyboard connectors
SATA0 ~ SATA5 SATA Ports
T-SGPIO-1/TSGPIO-2 Serial General Purpose Input/Output Header for SATA
USB0/1, USB4/5, USB2/3, USB6/7 Universal Serial Bus (USB) Ports, Type-A Ports and Headers
VGA VGA Connector
Chapter 1: Introduction
1-7
Motherboard Features
CPU
Single AMD Opteron 6100 series (Socket G34 type) processor
Note: Refer to our web site for details on supported processors.
Memory
Single/Dual/Tri/Quad channel DIMM slots supporting up to 128 GB of DDR3-
1333/1066/800 registered ECC SDRAM or 32 GB of DDR3-1333/1066/800 MHz
unbuffered ECC/non-ECC SDRAM
Note: Refer to Section 2-4 before installing memory and our web site for recommended DIMMs.
Chipset
AMD SR5650 chipset and one SP5100 Southbridge chipset
Expansion Slots
One (1) PCI-Express x8 (in x16 slot) Gen. 2
One (1) PCI-Express x8 Gen. 2
One (1) PCI-Express x4 (in x8 slot) Gen. 2
Three (3) PCI slots
BIOS
16 Mb AMIBIOS
®
SPI Flash ROM
APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS
2.3, Real Time Clock Wakeup, Plug and Play (PnP), BIOS resume hot keys,
Hardware BIOS Virus Protection
PC Health Monitoring
Onboard voltage monitors
Fan status monitor with rmware/software on/off and speed control
Watch Dog
Environmental temperature monitoring via BIOS
Power-up mode control for recovery from AC power loss
System resource alert (via included utility program)
Auto-switching voltage regulator for the CPU core
CPU thermal trip support
I
2
C temperature sensing logic
Chipkill Support
1-8
H8SGL(-F) Serverboard User’s Manual
ACPI Features
Microsoft OnNow
Slow blinking LED for suspend state indicator
BIOS support for USB keyboard
Wake-On-LAN (WOL)
Onboard I/O
Six (6) SATA ports supported by an on-chip SATA controller (RAID 0, 1, 10
supported)
Eight (8) USB (Universal Serial Bus 2.0) ports (2x rear, 4x header, 2x type A)
Two (2) LAN ports supported by two onboard Intel® 82574 dual port Ethernet
controller for 10/100/1000Base-T
One (1) dedicated IPMI LAN port (H8SGL-F only)
One (1) VGA port supported by an onboard Matrox
®
G200 graphics controller
(with 16 MB DDR2 memory)
One (1) UDMA IDE 133/100 connector
Two COM Ports (one external serial port, one Fast UART 16550 port)
Other
Onboard power LED
Chassis intrusion detection
CD Utilities
BIOS ash upgrade utility
Super Doctor III
IPMI 1.5 / 2.0
Dimensions
ATX form: 12" x 8" (305 x 203 mm)
Chapter 1: Introduction
1-9
DIMM A0
DIMM A1
CPU1
HT3 Link
16/16-3.2GHz
DIMM B0
DIMM B1
DIMM C0
DIMM C1
DIMM D0
DIMM D1
PCI SLOT1
PCI-E GEN2 X8
Slot6 PCIE x8/x16
IDE (ATA/133)
SA
TA x6
PCI-E GEN2 X8
Slot5 x8
PCI-E GEN2 x1
INTEL
82574L
RJ45
A-Link
SP5100
BMC
VGA
WPCM450-R
PCI
LPC
SMBus
SIO
W83527HG
HWM
W83795G
SPI Flash
KB/MS
COM2
RMII
DDR2 SDRAM
64MB X16
PSU I2C
IPMB
FE PHY
RTL8201N
VGA
RJ45
Clock Gen
TPM
SR5650
COM1
RJ45
INTEL
82574L
PCI SLOT2
PCI SLOT3
PCI-E GEN2 X4
Slot4
SWITCH
PCI-E GEN2 x1
8xUSB
Figure 1-3. AMD SR5650/SP5100 Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly represent
the features on your motherboard. See the previous pages for the
actual speci cations of your motherboard.
1-10
H8SGL(-F) Serverboard User’s Manual
1-3 Chipset Overview
The H8SGL(-F) serverboard is based on the AMD SR5650/SP5100 chipset. This
chipset functions as a Media and Communications Processor (MCP). Controllers for
the system memory are integrated directly into AMD Opteron processors.
AMD SR5650/SP5100 Processor
The AMD SR5650/SP5100 are each a single-chip, high-performance HyperTransport
peripheral controller. It includes a 22-lane PCI Express interface, an AMD Opteron
16-bit Hyper Transport interface link, a six-port Serial ATA interface, a dual-port Gb
Ethernet interface and a eight-port USB 2.0 interface. This hub connects directly
to the CPU.
HyperTransport Technology
HyperTransport technology is a high-speed, low latency point to point link that was
designed to increase the communication speed by a factor of up to 48x between
integrated circuits. This is done partly by reducing the number of buses in the
chipset to reduce bottlenecks and by enabling a more ef cient use of memory
in multi-processor systems. The end result is a signi cant increase in bandwidth
within the chipset.
1-4 PC Health Monitoring
This section describes the PC health monitoring features of the H8SGL(-F)
serverboard. The serverboard has an onboard System Hardware Monitor chip that
supports PC health monitoring.
Onboard Voltage Monitors
The onboard voltage monitor will continuously scan crucial voltage levels. Once
a voltage becomes unstable, it will give a warning or send an error message to
the screen. Users can adjust the voltage thresholds to de ne the sensitivity of the
voltage monitor. Real time readings of these voltage levels are all displayed in
BIOS.
Fan Status Monitor with Firmware/Software Speed Control
The PC health monitor can check the RPM status of the cooling fans. The onboard
fans are controlled by thermal management via BIOS.
Chapter 1: Introduction
1-11
CPU Overheat/Fan Fail LED and Control
This feature is available when the user enables the CPU overheat/Fan Fail warning
function in the BIOS. This allows the user to de ne an overheat temperature. When
this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail
warning LED is triggered.
Auto-Switching Voltage Regulator for the CPU Core
The 6-phase-switching voltage regulator for the CPU core can support up to Opteron
6100SE series processors and auto-sense voltage IDs ranging from 0.8 V to 1.55V.
This will allow the regulator to run cooler and thus make the system more stable.
1-5 Power Con guration Settings
This section describes the features of your motherboard that deal with power and
power settings.
Microsoft OnNow
The OnNow design initiative is a comprehensive, system-wide approach to system
and device power control. OnNow is a term for a PC that is always on but appears
to be off and responds immediately to user or other requests.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.
BIOS Support for USB Keyboard
If a USB keyboard is the only keyboard in the system, it will function like a normal
keyboard during system boot-up.
Main Switch Override Mechanism
The power button can function as a system suspend button. When the user
depresses the power button, the system will enter a SoftOff state. The monitor
will be suspended and the hard drive will spin down. Depressing the power button
again will cause the whole system to wake-up. During the SoftOff state, the power
supply provides power to keep the required circuitry in the system alive. In case the
system malfunctions and you want to turn off the power, just depress and hold the
power button for 4 seconds. The power will turn off and no power will be provided
to the motherboard.
1-12
H8SGL(-F) Serverboard User’s Manual
Wake-On-LAN (WOL)
Wake-On-LAN is de ned as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, up-dates and access
tracking can occur after hours and on weekends so that daily LAN traf c is kept
to a minimum and users are not interrupted. The motherboard has a 3-pin header
(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has
WOL capability. Wake-On-LAN must be enabled in BIOS.
1-6 Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
Please refer to the pinout information for the power connectors in Section 2-7 of
Chapter 2 for detailed information on power requirements for the H8SGL(-F).
In areas where noisy power transmission is present, you may choose to install a
line lter to shield the computer from noise. It is recommended that you also install
a power surge protector to help avoid problems caused by power surges.
Warning: To prevent the possibility of explosion, do not use the wrong type of
onboard CMOS battery or install it upside down.
1-7 Super I/O
The disk drive adapter functions of the Super I/O Winbond® BMC chip includes a
data separator, write pre-compensation circuitry, decode logic, data rate selection,
a clock generator, drive interface control logic and interrupt and DMA logic. The
wide range of functions integrated onto the Super I/O greatly reduces the number
of components required for interfacing with oppy disk drives.
The Super I/O provides two high-speed, 16550 compatible serial communication
ports (UARTs), one of which supports serial infrared communication. Each UART
includes a 16-byte send/receive FIFO, a programmable baud rate generator,
complete modem control capability and a processor interrupt system. Both UARTs
provide legacy speed with baud rate of up to 115.2 Kbps as well as an advanced
speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support higher speed
modems.
The Super I/O provides functions that comply with ACPI (Advanced Con guration
and Power Interface), which includes support of legacy and ACPI power management
through a SMI or SCI function pin. It also features auto power management to reduce
power consumption.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

Supermicro H8SGL-F User manual

Category
Server/workstation motherboards
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI