INSTALLATION INSTRUCTIONS
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada
Phone: 1.800.368.9700
Fax: 1.800.832.4888
Other Locations
Phone: (001).714.632.7100
Fax: (001).714.632.1044
EUROPE
Swallow House,
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
Polaris™
Universal Projector Mount
Model: MAG-PRO/MAG-PRO-W
9530-001-031-0B
MAG-PRO/MAG-PRO-W
Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Contact Premier Mounts with any questions:
(800) 368-9700
Contents
Warning Statements
Weight Limit
Maximum Projector Weight:
25 lbs.
THE CEILING STRUCTURE MUST BE CAPABLE OF
SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF
THE PROJECTOR. IF NOT, THE CEILING STRUCTURE
MUST BE REINFORCED.
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND
COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION
FOR FUTURE REFERENCE.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED, AS OUTLINED
IN THESE INSTALLATION INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE, SERIOUS
PERSONAL INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE
PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY
UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS,
DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR
IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
At least two qualied people should perform the assembly procedure. Personal injury and/or property damage can result
from dropping or mishandling the projector.
If mounting to wall studs or ceiling studs, make sure that the mounting screws are anchored into the center of the wall studs
or ceiling studs. Use of an edge-to-edge stud nder is recommended.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there
are no electrical wires in wall. Cutting or drilling into an electrical line may cause serious personal injury.
Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a
water or gas line may cause severe property damage or personal injury.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious
personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of
impact.
Weight Limit. .................................................................................................................................................................... 2
Warning Statements. ....................................................................................................................................................... 2
Installation Tools. ............................................................................................................................................................. 3
Parts List.......................................................................................................................................................................... 3
Features. ......................................................................................................................................................................... 4
Attaching the MAG-PRO/MAG-PRO-W Mount to the Projector. ..................................................................................... 5
Attaching the Projector Plate. .......................................................................................................................................... 5
Selecting the Mounting Hardware. ............................................................................................................................ 5
Multiple Mounting Point Installation. ................................................................................................................................ 6
Single Mounting Point Installation. .................................................................................................................................. 9
Installing the MAG-PRO/MAG-PRO-W Mount. ............................................................................................................... 9
MAG-PRO/MAG-PRO-W Mount Adjustment. .................................................................................................................11
Securing the MAG-PRO/MAG-PRO-W Projector . .........................................................................................................11
Technical Specications. ............................................................................................................................................... 12
Warranty. ....................................................................................................................................................................... 13
Disclaimer. ..................................................................................................................................................................... 13
MAG-PRO/MAG-PRO-W
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Make sure your Premier Mounts product has the following hardware and components before beginning installation. If
there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.
MAG-PRO/MAG-PRO-W Mount
(Qty 1)
MAG-PRO/MAG-PRO-W Mount Hardware
CLS
(Qty 1)
M5 Security Wrench
(Supplied)
Pencil Protective Eyewear
Phillips Tip Screwdriver
Ladder
Mounting Leg
(Qty 4)
Barrel Cap
(Qty 4)
2
1
Tape Measure
Star Washers
(Qty 2)
M3 Security Wrench
(Supplied)
Lock-It™ Security Hardware
M2.5 x 8mm Screw
(Qty 4)
M3 x 16mm Screw
(Qty 4)
M4 x 12mm Screw
(Qty 6)
M5 x 12mm Screw
(Qty 4)
M6 x 12mm Screw
¼-20 x
5
(Qty 1)
M3 Flat Washer
(Qty 4)
M2.5 x 10mm Screw
(Qty 4)
(Qty 4)
MAG-PRO/MAG-PRO-W
Page 4 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Features
Lock-It™ Security Hardware
Security hardware deters
tampering
Congratulations on the purchase of your new Premier Mounts Polaris™ Universal Projector Mount. Your
MAG-PRO/MAG-PRO-W Mount may be secured to a1-½˝ NPT. The Polaris™ features our exclusive MagnaGuide™
Technology which assists the installer for quicker installation times and peace of mind.
Please read these installation instructions once thoroughly before attempting to install your Premier Mounts product.
Please take a minute to familiarize yourself with the contents of the package and make sure you have all the parts and
tools you need to safely complete the installation.
In addition, some steps of this installation may require two people to prevent personal injury and/or damage to your
projector. Please observe all warnings in the following installation procedure and utilize proper safety equipment at all
times.
MagnaGuide® Technology
Powerful magnets assist
installation and guide the projector
plate into the ceiling mount
Cable Routing
Discretely manage cables
through mount and into ceiling
Radial Glide®
Up to 6° of adjustment in any
direction
Security Leveling Barrel
Allows the user to easily secure the mount
with a padlock.
Adjustable Leveling Barrels
You can quickly level the mounting legs
without any specialized tools.
MAG-PRO/MAG-PRO-W
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 5
Attaching the Projector Plate
Selecting the Mounting Hardware
Insert a small straw or toothpick into the threaded
inserts found on the bottom or top of the projector.
®
Use a pencil to mark the depth of the threaded insert
on the small straw or toothpick.
¯
Mark the straw or toothpick 1/8” above the depth of
the threaded insert, as shown in Figure 1.
°
Insert the small straw or toothpick into the remaining
threaded inserts to compare and verify their depth
using the straw or toothpick’s 1/8” allowance mark.
±
Locate the correct diameter screw for the threaded
insert.
If the screw you selected is longer than the 1/8”
allowance mark on the small straw or toothpick,
as shown in Figure 2 and Figure 3, do not use this
screw. The screw length must not bypass the mark.
²
Test each size of the screws provided. The correct
screws should thread easily into the mounting point
and not pull out when tension is applied.
Does your projector have multiple mounting points
or a single mounting point?
Lock-It™ Security Hardware Pack (Optional)
The MAG-PRO Mount comes with the option of using
Lock-It™ Security Screws. To use the security screws,
simply replace the M6 x 12mm Phillips Pan head screws
with the M6 x 12mm security screws. Once the hardware
has been changed, adjust the MAG-PRO Mount and
tighten the M6 x 12mm security screws using the M5
Security Allen wrench (supplied).
If your projector has multiple mounting points,
proceed to the “Multiple Mounting Point
Installation” section.
If your projector has a single mount point, remove
the pre-installed mounting legs on the universal
projector plate and skip to the “Single Mount Point
Installation” section.
Attaching the MAG-PRO/MAG-PRO-W Mount to the Projector
Locate the mounting points on the bottom of the
projector (see arrows to the right).
Proceed to the “Attaching the Projector Plate”
section.
Small Straw or Toothpick
Small Straw
or Toothpick
Small Straw
or Toothpick
Marking the 1/8”
Allowance
Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
Adjustable Leveling Barrels
You can quickly level the mounting legs
without any specialized tools.
MAG-PRO/MAG-PRO-W
Page 6 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Step 2
Attach the appropriate number of mounting legs to the
projector using the corresponding mounting hardware.
Do not tighten the mounting hardware at this time.
Only attach to the projector manufacturer’s
specied mounting points on the projector chasis
with a minimum of three mounting legs. Please
follow all safety instructions specied by the
projector manufacturer as well as the safety
instructions outlined in this manual.
Multiple Mounting Point Installation
Step 1
Locate the projector’s mounting points.
®
Position an appropriate number of mounting legs on
the projector.
The four mounting legs come pre-installed. If there are
less than four thread inserts on the projector, remove
the appropriate number of mounting legs.
The number and placement of mounting
points on projectors varies between projector
manufacturers. Refer to you projector’s technical
specications for the number and location of the
mounting points on your specic projector.
MAG-PRO/MAG-PRO-W
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 7
Step 3
If the mounting legs need to be leveled, rotate the
leveling barrels to level the mounting bracket.
®
To raise the mounting legs, rotate the leveling barrel
clock-wise. To lower the mounting leg, rotate the
leveling barrel counter clock-wise.
Raise or lower each of the mounting legs, by
rotating the leveling barrels, until all of the mounting
legs are at an equal height.
• Lower the mounting leg by rotating the leveling
barrel counter-clockwise.
• Raise the mounting legs by rotating the leveling
barrel clockwise.
¯
When the desired position is achieved, tighten the
mounting screws to the projector and then tighten the
hex head leg screws with the M5 Allen wrench.
Identify the projector’s approximate front-to-back
center of gravity. Place your hands on each side of
the projector and gently lift it an inch from the surface
on which it is resting. Carefully adjust your grip on the
projector until it seems balanced from front-to-back.
Mentally note the apparent center of gravity.
®
Identify the projector’s approximate side-to-side
center of gravity. Place your hands on the front and
back of the projector and gently lift it an inch from the
surface on which it is resting. Carefully adjust your
grip on the projector until it seems balanced from
side-to-side. Mentally note the apparent center of
gravity.
¯
Place the Universal Projector Plate (if not already
attached) on top of the mounting legs with the center
hole as close as possible to the projector’s center of
gravity.
Step 4
Mounting Hardware Too Long?
The depth of some projector mount points may
prevent you from tightening the M2.5 and M3
mounting hardware.
You can reduce the length of the M2.5 and
M3 mounting hardware by stacking up to a
maximum of ve (5) M3 at washers inside the
leveling barrel.
Avoid stacking too many M3 washers; the
mounting hardware must thread into the
projector mount point at least four (4) complete
turns.
Side-to-Side
Center of Gravity
Front-to-Back
Center of Gravity
MAG-PRO/MAG-PRO-W
Page 8 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Step 7
Attach the Projector Plate to each of the mounting
legs by inserting and tightening one (1) M6 x 12mm
screw through the Projector Plate into the M6 square
nut on each of the mounting legs.
Do not overtighten the M6 x 12mm screws.
®
Insert one (1) Barrel Cap into the end of each leveling
barrel (except the security leveling barrel).
Step 6
Tighten the mounting screws which secure the
mounting legs to the projector.
Do not overtighten the mounting screws.
Step 5
Position the legs accordingly for best conguration.
You may raise or lower each leg independently by
turning the leveling barrels.
®
Secure the legs to the projector plate by screwing
M6 x 12mm security screws into the M6 square nut
(do not overtighten) on the mounting legs.
¯
Verify the position of the integrated sliding M6 square
nut in the mounting leg relative to a nearby slot on the
Projector Plate.
If the M6 square nut is not aligned with any slot, you
can use any thin tool, such as a toothpick, to nudge
it into alignment.
Sliding M6
Square Nut
MAG-PRO/MAG-PRO-W
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 9
Single Mounting Point Installation
A single ¼-20 x
5
/16″ screw must be used to attach the
Projector Plate to the projector if your projector has only
one mounting point.
Do not overtighten the ¼-20 x
5
/16″ screw.
Proceed to the “Installing the
MAG-PRO/MAG-PRO-W Mount” section.
Installing the MAG-PRO/MAG-PRO-W Mount
The Polaris™ MAG-PRO/MAG-PRO-W may be
attached to 1-½˝ standard threaded pipe (NPT), or
one of Premier Mounts adjustable-height ceiling
adapters. Please refer to the installation instructions
that come with these adapters.
Step 1
Lift the MAG-PRO/MAG-PRO-W up to the
preinstalled 1-½˝ NPT, or any of Premier Mounts
compatible adapters.
When attaching the MAG-PRO/MAG-PRO-W to the
pipe, please ensure that the MAG-PRO/MAG-PRO-W
is threaded on at least four (4) complete turns.
®
Thread the MAG-PRO/MAG-PRO-W onto the length
of 1-½˝ NPT, or any of Premier Mounts compatible
adapters.
1-½˝ standard threaded
pipe (NPT)
If you are having difculty achieving four complete
turns, insert a screwdriver through the access hole
and apply pressure while turning the MAG-PRO/
MAG-PRO-W (see below).
Four complete turns
MAG-PRO/MAG-PRO-W
Page 10 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Step 3
Step 4
Attach the two (2) M4 x 12mm security screws and
star washers that are located on each side of the
locking tab.
Do not release your hold on the projector until the
upper and lower assemblies are engaged and the
locking tab is in place.
Slowly raise the projector toward the upper assembly.
®
Once the projector is close to the upper assembly,
MagnaGuide™ Technology will pull the lower
assembly into the upper assembly and the locking tab
will engage.
THE MAGNETS ARE USED FOR GUIDING THE
UNIT ONLY! PLEASE MAKE SURE THE TWO (2)
M4 X 12MM SCREWS ARE USED TO SECURE
THE PROJECTOR.
M4 x 12mm
Security Screw
and Star Washer
Security Wrench
Secure the MAG-PRO/MAG-PRO-W by tightening
the set screw with the M3 security Allen wrench
(supplied).
®
Route any cables up through the 1-½˝ NPT and into
the ceiling structure.
If the PP-FCTA Ceiling Mount is to be used, the CLS
must rst be threaded into the
MAG-PRO/MAG-PRO-W. For further installation
instructions, please refer to the PP-FCTA installation
manual.
Step 2
Proceed to the “MAG-PRO/MAG-PRO-W Mount
Adjustment” section.
M3 Security
Wrench
Set Screw
MAG-PRO/MAG-PRO-W
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 11
MAG-PRO/MAG-PRO-W Mount Adjustment
Step 1
After the projector has been installed, you may need to
adjust it. To adjust the projector:
Loosen the M5 set screw using the M5 Allen wrench
(both sides).
®
Adjust the projector to the correct position. Firmly
grasp the projector in both hands, and tilt either
forward or backward to adjust the level.
-OR-
¯
Firmly grasp the projector in both hands and rotate
side to side for orientation adjustment.
°
Tighten both M5 set screws using the M5 Allen
wrench.
M5 Set Screw
Securing the MAG-PRO/MAG-PRO-W Projector
Your MAG-PRO/MAG-PRO-W Projector Mount includes one pre-installed Security Leveling Barrel in a mounting leg
which can provide additional theft deterrence for your projector when used with a padlock or PCB-CSL1 Security Cable.
Shown below is an example of how you can route a PCB-CSL1 through the Security Barrel. The Security Cable is
routed through the Security Barrel after the standard leveling barrel is replaced by the Security Barrel and the projector
mount is securely attached to the projector as per the installation instructions.
The PCB-CSL1 kit also includes a Cable Looper which you can use to create a tight loop for cable management.
The PCB-CSL1 kit, which contains one (1) 18” braided cable, one (1) chassis sleeve, one (1) cable looper, one (1)
cylinder lock, and two (2) cylinder lock keys, is sold separately. Additional cylinder locks, additional Security Barrels,
and longer cables are also sold separately.
Padlock
(Combination or Keyed)
PCB-CSL1
MAG-PRO/MAG-PRO-W
Page 12 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Technical Specications
All measurements are in inches [millimeters].
MAG-PRO/MAG-PRO-W
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 13
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original
owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be shipped to you
at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS,
PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM
IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS IS NOT
RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO,
INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE
PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address
below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer purchaser must
accompany all warranty claims. Warranty claims must also include a description of the problem, the purchaser’s name,
address, and telephone number. General inquiries can be addressed to Premier Mounts Customer Service at 1-800-
368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE.
©Premier Mounts 2010
Warranty
Disclaimer
Premier Mounts intends to make this manual accurate and complete. However, Premier Mounts makes no claim that
the information contained herein covers all details, conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this product. The information contained in this document
is subject to change without notice or obligation of any kind. Premier Mounts makes no representation of warranty,
expressed or implied, regarding the information contained herein. Premier Mounts assumes no responsibility for
accuracy, completeness or sufciency of the information contained in this document.
Warranty
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
Premier Mounts MAG-PRO Specification
- Category
- Projector mounts
- Type
- Specification
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Premier Mounts MAG-PRO Polaris Universal Projector Mount User manual
-
Premier Mounts MAG-PRO-W User manual
-
Premier Mounts Indoor Furnishings MAG User manual
-
Premier Mounts EST250 Owner's manual
-
-
-
-
-
-
Other documents
-
Premier MAG Specification
-
-
Lennox iComfort Thermostat Mag-Mount (12X99) Installation guide
-
-
Da-Lite Cable Lock Kit, A-565 User manual
-
Strong SM-FIXPOLE-24-WH Owner's manual
-
-
-
-