SINGER 14T968DC Owner's manual

14T968DC
SINGER
Brand
SINGER
Model
14T968DC
Category
Sewing machines
Type
Owner's manual

This manual is also suitable for

14T968DC
Instruction Book
SINGER is a registered trademark of The Singer Company Limited or its affiliates.
©2008 The Singer Company Limited or its affiliates. All rights reserved.
14T968DC
This SINGER sewing machine, model 14T968DC,
IMPORTANT SAFETY INSTRUCTIONS
When using this machine, basic safety precautions should always be followed including the following.
Read all instructions before using the machine.
* The machine should never be left unattended when plugged in. Always unplug the machine from the
electric outlet immediately after using and before cleaning.
* Always unplug before re-lamping. Replace bulb with the same type rated 15 watts. Be sure to replace the
face plate which covers the light bulb before operating the machine.
* Be sure that the electrical voltage of the electric outlet (wall receptacle) is the same as the rated voltage of
the motor.
* Use this machine only for its intended use as described in this Instruction Book. Use only attachments
recommended by the manufacturer as contained in the Instruction Book.
* To disconnect, turn all controls to the off ("0") position, then remove plug from outlet.
* Disconnect the power line plug from the socket outlet or switch the machine off when making any adjustments
in the needle area, such as threading needle and loopers, changing needle, changing throat plate or changing
presser foot, etc.
* Always unplug the machine from the electrical outlet when removing covers, lubricating, or when making
any other user servicing adjustments mentioned in the Instruction Book.
* Do not attempt to adjust the motor belt. Contact your nearest Service Center should any adjustment be
required.
* Handle the foot controller with care and avoid dropping it on the floor. Be sure not to place anything on top
of the controller.
* Always use the proper needle plate. The wrong plate can cause the needle to break.
* Do not use bent needles.
* When sewing, keep fingers away from all moving parts. Special care is required around the sewing machine
needle.
* Do not pull or push fabric while stitching. It may deflect the needles causing them to break.
* For double insulated machines, when servicing, use only identical replacement parts. See instructions for
Servicing of Double-Insulated Appliances.
* Never operate the machine if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into the water. Return the machine to the nearest authorized dealer or
Service Center for examination, repair, electrical, or mechanical adjustment.
* Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and
foot controller free from the accumulation of lint, dust and loose cloth.
* Never drop or insert any object into any opening.
2
DANGER -To reduce the risk of electric shock:
WARNING -To reduce the risk of burns, fire, electric shock or injury to persons:
* Do not use outdoors.
* Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
* Do not allow to be used as a toy. Close attention is necessary when the machine is used by or near
children.
* Do not expose the machine or machine plastic case to sunlight directly. Also, do not keep it in a very warm
or damp place.
* Do not touch the machine, foot controller and power line cord with wet hand, wet cloth or with anything wet.
* Do not connect power line cord to one of the many cords connected to one power outlet with adapters.
* Use machine on flat and stable table.
* Be sure to close the looper cover before operating the machine.
* Keep presser foot and needles away from children's reach.
* Be sure the light bulb has cooled off before changing with a new one.
* Do not dismantle or modify the machine yourself.
* The appliance is not intended for use by young children or infirm persons without supervision.
* Be sure to turn off the power switch and disconnect the power line plug before caring for your machine as
* Young childen should be supervised to ensure that they do not play with the appliance.
* Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
instructed in the Instruction Book.
* SERVICING OF DOUBLE-INSULATED PRODUCTS. In a double-insulated product, two systems of
insulation is provided instead of grounding. No grounding means is provided on a double-insulated product,
nor should a means for grounding be added to the product. Servicing of a double-insulated product requires,
extreme care and knowledge of the system, and should be done only by qualified service personnel.
Replacement parts for a double-insulated product must be identical to those parts in the product. A double-
Insulated product is marked with the word "DOUBLE-INSULATION" or "DOUBLE-INSULATED".
3
TABLE OF CONTENTS
1. Selection stitches & Auto tension..............................
2. Handy Reference Chart............................................
3. Accessories..............................................................
4. Needle Information...................................................
5. Principal Parts..........................................................
6. How to Open Looper Cover.....................................
7. Principal Parts Behind Looper Cover.......................
8. Preparation prior to sewing......................................
9. Removal and Replacement of Waste Tray..............
10. Preparation for Threading........................................
*Setting up the thread guide holder............................
*Anti-spill net..............................................................
*Spool cap..................................................................
11. How to Remove and Insert Needles........................
*Needle position.........................................................
*To remove needle(s).................................................
*To insert needle(s)....................................................
12. Threading the Machine...........................................
*Threading diagram...................................................
*Understanding the color code..................................
*To thread the machine correctly...............................
1) Threading the upper looper (Green)...................
2) Threading the lower looper (Red).......................
3) Threading the chain stitch looper (Brown)..........
4) Threading the overedge right needle (Blue).......
5) Threading the chain stitch needle (Orange)........
6) Threading the cover stitch needles.....................
Threading the cover stitch left needle (Orange)
Threading the cover stitch middle/chain stitch
needle(Blue).....................................................
Threading the cover stitch right needle(Green).
13. How to Change Threads / Tie on Method...............
14. How to Adjust the Stitch length...............................
15. How to Adjust the Seam width................................
*Width adjustment by changing needle position........
*Width adjustment with adjustment knob...................
16. How to Adjust the Presser Foot Pressure...............
17. Differential Feed......................................................
*Gathered overedge...................................................
*Stretch overedge......................................................
18. How to Disengage Movable Upper Knife................
19. To Convert upper Looper to Spreader....................
*To use the spreader..................................................
*To disengage to upper looper...................................
20. Standard overedge and Rolled Hem Stitching........
*To sew standard overedge.......................................
*To sew rolled hem....................................................
21. Chaining Off and Test Sewing............................
22. Settings and Sewing Instructions........................
1) Double chain stitch...........................................
2) 2-Thread Wrapped Edge Overlock...................
3) 2-Thread Overedge..........................................
4) 3-Thread Overlock............................................
5) 3-Thread Flatlock..............................................
6) 3-Thread Ultra Stretch Mock Safety Stitch.......
7) 4-thread Ultra Stretch Mock Safely Stitch.........
8) 4-Thread Safety Stitch......................................
9) 5-Thread Safety Stitch......................................
23. How to Sew a Cover Stitch.................................
24. How to Sew a Rolled hem..................................
1) 3-thread standard rolled hem stitching.............
2) 3-thread upper looper thread wrapped
rolled hem stitching...........................................
3) 2-thread standard rolled hem stitching.............
4) 2-thread lower looper thread wrapped
rolled hem stitching...........................................
25. Stitch Variations and Sewing Techniques...........
*Decorative Flatlocking..........................................
*How to sew an overlock blind hem.......................
*How to sew pin tucks...........................................
*Turning square corners........................................
*Pin placement.......................................................
*Securing the thread chain.....................................
*How to reinforce a seam.......................................
*Braiding by chaining off........................................
26. Machine Maintenance.........................................
*Cleaning the machine...........................................
*Oiling the machine................................................
*How to replace the moveable upper knife............
*How to exchange light bulb...................................
27.Optional Accessories...........................................
*Snap-on type presser foot....................................
*Optional presser feet............................................
1) Elastic foot.......................................................
2) Blind hem foot..................................................
3) Shirring foot......................................................
4) Pearl/Sequin foot.............................................
5) Piping/Cording foot..........................................
6) Taping foot.......................................................
28. Troubleshooting Chart.........................................
29. Relationship between Cloth, Thread and Need..
30. Specification........................................................
Page Page
38
39
39
41
42
43
44
45
46
47
48
49
54
55
55
56
56
58
59
60
60
61
62
62
63
63
64
64
64
65
66
67
67
68
68
68
68
68
68
68
69
70
71
5
8
9
9
10
12
12
12
13
14
14
14
14
15
15
15
15
16
16
16
17
17
18
20
21
23
25
25
26
28
30
31
31
31
31
32
33
33
34
35
36
36
36
37
37
37
1
2
3
4
1. SELECTION OF STITCHES & AUTO TENSION
Seams also can be sewn at desired
A 4 mm and 6 mm overlock seam width
ideal for flatlock (butted or lapped) seams
overedging and seaming on common
stitching with decorative thread. Also,
Mock Safety such as tricot and spandex.
Stretch Mock for medium to heavyweight stretchy
This machine is capable of producing various types of stitches according to the combination of Auto Tension
Selected, needle positions, threading methods, and the use of convertible right looper/spreader.
Stitch Type Reference
Page
1. Double A 1-needle 2-thread straight stitch is used
Chain Stitch for construction or decorative stitching.
39
distance from edge of fabric by
disengaging the right looper and movable
knife.
2. Two-thread 1-needle 2-thread stitch is used for
Wrapped Edge
Overlock
It is also ideal for rolled and blind hemming.
41
can be obtained by changing the needle
position.
3. Two-thread 1-needle 2-thread stitch is used for
Overedge overedging common fabrics. It is also
42
and blind hemming. A 4 mm and
6 mm overedge seam width can be
obtained by changing the needle position.
Overlock
43
fabrics. A 4mm and 6 mm overlock seam
width can be obtained by changing the
needle position.
5. Three-thread 1-needle 3-thread stitch is used for
Flatlock butted or lapped seams and ornamental
44
a 4 mm and 6 mm flatlock width can
be obtained by changing the needle
position.
6. Three-thread 2-needle 3-thread stitch that is ideal for
Ultra-Stretch lightweight, extremely stretchy fabrics
45
Stitch
7.Four-thread Ultra- 2-needle 4-thread stitch that is ideal
46
Safety Stitch fabrics such as double knits and swim
Wear.
4. Three-thread 1-needle 3-thread stitch is used for
seaming lightweight or stretch fabrics.
5
ATD : Auto Tension Dial Selected
ATD: D
ATD: E
ATD: B
ATD: F
ATD: G
ATD: A
ATD: A
ATD: G
ATD: D
6
Stitch Type Reference
Page
8. Four-thread
Safety Stitch made up of combined 2-thread
overedge and double chainstitch.
47
9. Five-thread The 5-thread stitch is a safety stitch
Safety Stitch made up of combined 3-thread
Wide overlock and double chainstitch.
48
A wide seam is formed by using left needle.
Overedge and seaming can be done
in one operation on non-stretch fabrics.
10. Five-thread The 5-thread stitch is a safety stitch
Safety Stitch made up of combined 3-thread
Narrow overlock and double chainstitch. 48
11. Cover Stitch 2-needle, 3-thread cover stitch is
Narrow suitable for stretchy fabrics such as
(2.8mm) knits, etc. 51
A narrow seam is formed by using left
and middle needles.
12. Cover Stitch 2-needle 3-thread cover stitch is
Wide suitable for stretchy fabrics such as
(5.6mm) knits, etc.
51
A wide seam is formed by using left
and right needles.
13. Triple Cover 3-needle 4-thread cover stitch is
Stitch suitable for stretchy fabrics such as
(5.6mm) knits, etc.
52
A triple seam is formed by using left,
middle, and right needles
.
14. Three-thread 1-needle 3-thread stitch is used for sewing
Rolled Hem narrow rolled hems.
55
A narrow seam is formed by using right
Needle. Overege and seaming can be done
in one operation on non-stretch fabrics.
The 4-thread stitch is a safety stitch
ATD : Auto Tension Dial Selected
ATD: I
ATD: B
ATD: A
ATD: K
ATD: H
ATD: J
ATD: C
* Depending on the needle positions used, this machine can sew 2-thread and 3-thread standard width 4 mm
overedge anda6mmwide overedge seams.
Also, for overedging heavyweight fabrics, the seam width can be increased still more by turning the overedge
seam width adjustment knob. (See page )
31
Overedge width 4.0 mm 6.0 mm
Needle used Overedge right needle Overedge left needle
Needle thread Blue Orange
tension fine tuning
7
Stitch Type
Correct Threading / Tension Path: When
using the Auto Tension Dial (ATD), the correct
tension is set automatically.
*When option 2, 3, 6, 8 selected, use spreader.
*When option 1, 11, 12, 13 selected, turn upper knife down, move seam width finger knob to setting R, and change looper cover
attached cover (A) into (B).
*Auto tension settings are based on medium weight fabric and standard # 60 polyester spun thread. It can satisfy most requirements
for sewing. If using a different thread weight or fabric and the result is not as you expected, please adjust tension in small increments.
Double Chain Stitch
Two - Thread
Wrapped Edge
Overlock
Two - Thread
Overedge
Three - Thread
Overlock
Three - Thread
Flatlock
Three - Thread
Ultra - Stretch mock
Safety Stitch
four - Thread
Ultra - Stretch mock
Safety Stitch
Four - Thread
Safety Stitch
Five - Thread
Safety Stitch
Wide
Five - Thread
Safety Stitch
Narrow
Cover stitch
Narrow
Cover stitch
Wide
Triple Cover stitch
Three - Thread
Rolled Hem
1
2
3
4
5
6
7
8
9
10
11
12
13
14
4.0mm
6.0mm
4.0mm
6.0mm
4.0mm
6.0mm
4.0mm
6.0mm
2.8mm
5.6mm
5.6mm
4.0mm
Page
Orange Blue
39
41
41
42
42
43
43
44
44
45
46
47
48
48
51
51
52
55
Green Red Brown
D
G
D
E
E
B
A
F
F
G
A
I
B
A
K
H
J
C
N
2
2
2
2
N
N
2
2
2
N
N
N
N
N
N
N
1
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
ATD: Auto Tension Dial Selection SL: Stitch Length
DF: Differential Feed L / C: Upper Looper driving clutch position
A
T
D
S
L
D
F
L
/
C
Needle
Position
8
2. HANDY REFERENCE CHART
C
L
L
L
L
L
L
L
L
L
L
L
L
L
C
C
C
L
1
2
3
4
5
6
789
10
11
12
Accessories are contained in the accessory case
1. Screw driver (large size)
2. Knife (stationary)
3. Thread Unwinder spool cap
4. Anti-spill net
5. Oiler
6. Allen Screw driver (small)
7. Tweezers
8. Needle set
9. Brush
10. Cone Adapters
11. Waste tray
12. Machine cover
This overlock uses a flat shank industrial needle
that eliminates the possibility of inserting the needle
backwards.
Do not attempt to use a standard household sewing
machine needle of any size or type in this overlock.
Singer needle #2022 size 14/90 is furnished with the
machine.
Only use Needle #2022 size 14/90 and 11/80 as
supplied in the accessory case.
9
1
1
5
1
1
1
1
1
5 (on machine)
1 in carton
1 in carton
#2022
Overlock needle
5
3. ACCESSORIES
4. NEEDLE INFORMATION
1. Thread guides and holder
2. Handle
8. Needle plate
9. Cloth plate
10. Looper cover
11. Power & light switch
12. Stitch length dial
13. Hand wheel
14. Spool stand
15. Cone adaptor
16. Spool pin
17. Waste tray
10
1 . Auto tension dial8
3. Left needle thread tension fine tuning lever (orange)
4. Right needle thread tension fine tuning lever (blue)
5. Upper looper thread tension fine tuning lever (green)
6. Lower looper thread tension fine tuning lever (red)
7. Chain stitch looper thread tension fine tuning lever (brown)
5. PRINCIPAL PARTS
2
1
3
4
5
6
7
8
10
9
11
12
13
14
15
17
16
18
19
20
21
22
19. Presser bar lifter and tension release
20. Differential feed adjusting dial
21. Cutting width dial
22. Presser foot pressure adjusting dial
11
PRINCIPAL PARTS
ON
OFF
2
1
Be sure to turn off power switch.
Push the cover to the right as far as it will go.
Pull cover down toward you.
Be sure looper cover is closed when
sewing.
1. Upper looper
2. Moveable Upper knife
3. Presser foot
4. Fixed position lower knife
5. Lower looper
6. Chain/Cover looper
7. Rolled Hem lever
8. Spreader
9. Upper looper clutch
Connect the controller/electric plug to the machine
receptacle.
Plug power line into electric outlet.
Power Switch: Push"l"mark side to turn "ON"
To run the machine and control the speed, press
the controller.
The harder you press, the faster the machine will sew.
To stop the machine from sewing, remove your foot
from the controller.
Push "O" mark side to turn "OFF"
Use only foot controller provided with this machine.
(Type 4C-316B for U.S.A. & CANADA only)
Be sure to make reference to "Warning" on following
Page.
12
Note: Machine will not operate when
Looper Cover is open.
8. PREPARATION PRIOR TO SEWING
6. HOW TO OPEN LOOPER COVER
7. PRINCIPAL PARTS BEHIND THE
LOOPER COVER
9
4
3
7
1
2
5
6
8
Caution:
Caution:
WARNING:
3
2
1
This appliance has a polarized plug (one blade wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized outlet only way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit contact a qualified electrician
to install the proper outlet. Do not modify the plug in any way.
13
Insert the waste tray under the looper cover.
Be sure the left side of waste tray is mounted near the
cutter where the scraps drop.
* Be sure that the electrical voltage of the electric outlet (wall receptacle) is the same as the rated
voltage of the motor.
* Handle the foot controller with care and avoid dropping it on the floor. Be sure not to place anything
on top of it when not in use.
* Disconnect the power line plug from the electric outlet when changing needles, presser feet
or when leaving the machine unattended. This eliminates the possibility of starting the machine
by accidentally pressing the controller.
To remove, hold the waste tray as shown and
pull it outward.
Replacement
Removal
Warning:
9. REMOVAL AND REPLACEMENT OF
WASTE TRAY
POLARIZED PLUG INFORMATION (FOR U.S.A. & CANADA ONLY)
14
10. PREPARATION FOR THREADING
When using synthetic threads that easily spill off
the cone, slip the anti-spill net furnished with the
machine over the thread from the bottom of the
cone leaving the thread end hanging free at the
top of the anti-spill net as shown on illustration.
Take out the thread guide from the top of
Styrofoam, and insert it as shown on illustration.
This machine is shipped with the thread guide
holder in the lowered position.
Fully extend the thread guide holder.
The two joints on the telescope will click into place
when they are correctly positioned.
Center the thread guides above the spool pins.
Place thread over the cone adapters on the spool
pins.
When using a regular thread spool, fit the spool cap
supplied with the machine onto the thread spool as
shown on illustration.
Anti-spill net
Spool cap
Press in
Thread spool
Note: Your new machine is threaded to sew
Triple Cover Stitch. Refer to Page 30 for
instructions on tying on to the threads.
Setting Up the Thread Guide Holder
Anti-spill Net
Spool Cap
11. HOW TO REMOVE AND INSERT
NEEDLES
B
To loosen
To tighten
C
Flat surface to the rear
B
B
D
E
A
A
B
C
E
D
C
E
D
D
A
15
Turn the hand wheel toward you until the needles are
at their highest position.
Place a thick piece of fabric [such as felt] under the
presser foot. Lower the needles halfway into the
fabric.
Loosen, but do not remove the needle set screws with
the small allen screwdriver. Hold the needles with
your fingers and raise the needle bar. The needles
will remain in the fabric.
A. Overedge needleleft
B. Overedge needleright
C. Cover stitch left needle
D. Cover stitch middle needle
E. Cover stitch right needle
With this machine, five needles can be inserted into
the needle clamp as shown in the drawing but only
one or two or three needles are to be used for sewing.
Do not attempt to use four or five needles.
The Instruction Book refers to different needle
positions by illustrating the needle clamp at right.
Note: When both the left and right overedge needles
are inserted, the left needle will be slightly
higher than the right.
When all cover stitch needles are inserted,the
center needle will be slightly higher than the right
needle and the left needle slightly higher than the
center needle.
Caution:
Be sure to disconnect the machine from the
electric outlet before removing needle(s).
Hold the needle with the flat surface to the back.
Insert the needle into the needle socket as far as it
will go.
When inserting a needle, if you first lower it down
into the hole in the needle plate it will line up with the
needle socket. Then direct it upwards
Note: When inserting needles into the A or B sockets
it is necessary to loosen both A & B Allen Screws.
After inserting the needles equally tighten both
screws.
Left, middle and right cover
stitch needle thread
Overedge left needle
Overedge right needle
Cover stitch right needle
Cover stitch middle needle
/ Chain stitch needle
Cover stitch left needle
Right overedge
needle thread
Chain stitch
needle thread
Left and right
overedge needle
thread
Needle Position
To Remove Needle (s)
To Insert Needles (s)
This machine uses Singer #2022 needles. Do not
use Standard Household Needles.
16
Chain stitch
Overlock
12. THREADING THE MACHINE
A color coded threading diagram is located inside
the looper cover for quick reference.
Thread the machine in the order 1 to 5 as shown.
Note: Threads go through the take-up lever cover
for Overlock and Chain stitching as shown.
A color coded threading diagram is located inside
the looper cover for quick reference.
Thread the machine in the order 1 to 4 as shown.
Note: Threads go through take-up lever
cover for Cover stitch as shown.
Threading Diagram: Cover Stitch
1. Upper looper thread............................
2. Lower looper thread............................
3. Chain stitch looper thread...................
4. Right needle thread............................
5. Chain stitch needle thread..................
1. Cover stitch looper thread.............
2. Right needle thread.......................
3. Middle needle thread.....................
4. Left needle thread..........................
Tension Color Code: Cover Stitch
Brown
Green
Blue
Orange
Green
Red
Brown
Blue
Orange
C
L
C
L
Tension Color Code: Overlock and Safety Stitch
4
2
1
3
5
4
4
3
3
2
1
1
2
5
2
4
1
3
Threading Diagram: Overlock and Safety Stitches
C
L
Caution:
Be sure to turn off power switch.
Thread the top cover
thread guide by pulling
the thread towards the
left until it slips under
guide. Then pull
thread along the right
side of button as
illustrated.
While holding thread with fingers, pass it between
the tension discs and pull thread down to make
certain it is properly located in between the
tension discs 3.
Thread the upper looper as indicated 1~9.
Note: The presser foot is raised by lowering the
Presser bar lifter. The motion allows a clear
path for the fabric when sewing.
Raise Presser foot to release tension discs.
17
Pass thread from back to the front through the
thread guide 1.
Note: The instructions on this page and the following pages
will guide you through the proper threading for each
color coded threading path.
Before threading, refer to the Handy Reference Chart
for information on Stitch Types, Settings, Needle
Sockets and Color Coded Threading Paths.
1) Threading the (Green)Upper Looper
To Thread The Machine Correctly
1
3
3
2
2
9
6
8
7
5
4
3
2
1
Raise Presser foot by lowering presser bar lifter to
release Tension discs.
18
Thread the top cover
thread guide by pulling
the thread towards the
left until it slips under
guide. Then pull thread
along the right side of
button as illustrated.
Thread the lower looper as indicated 1~10.
Thread the looper area of the machine following the
green color coded thread guides (4~9).
Thread the hole in the upper looper from front to
back 9. Note: Make sure thread passes behind lower
looper.
Note: Use tweezers provided in the accessory
case to aid in threading the looper.
Pull about 10cm(4 inches) of thread through the
looper and place to the back of the needle plate.
Pass thread from back to the front through the
thread guide 1.
2) Threading the (Red)Lower Looper
2
2
5
9
8
9
4
8
9
10
1
6
7
8
5
7
6
4
3
2
1
C
10
B
A
9
D
5
8
7
4
6
9
7
8
6
10
5
4
3
3
19
Thread the looper eye (A) from front to back.
Pull about 10cm (4 inches) of thread.
Position thread into V cutout (B) on threader.
Firmly hold thread tail with left hand and pull
Threader lever (C) up into place (D).
Turn the hand wheel toward you until the lower
looper extends out 5~10mm from the needle
plate edge.
Thread the looper area of the machine following
the red color coded thread guides 4~10.
Note: Use tweezers provided in the accessory
case to aid in threading the looper.
While holding thread with finger, pass it between
the tension discs and pull thread down to make
certain it is properly located in between the
tension discs 3.
Place the thread with the point of the tweezers
slightly from left and to the right of threading guide 4.
Place the thread with the point of the tweezers
slightly from front and to the back of threading guide 5.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

SINGER 14T968DC Owner's manual

14T968DC
SINGER
Brand
SINGER
Model
14T968DC
Category
Sewing machines
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents