Community R.15COAX User guide

Community R-Series Application Guide — Page 2

THE COMMUNITY R-SERIES

R.25

Two-way, full-range

100 Hz to 16 kHz

LF 1 x 8", HF 1 x ¾"

200W RMS, 500W PGM, 8 ohms

Available coverage pattern: 90° x 40°

For portable systems and as short throw fill speakers.

R.5

Two-way, full-range

85 Hz to 16 kHz

LF 1 x 12", HF 1 x 1"

200W RMS, 500W PGM, 8 ohms

Available coverage patterns: 60° x 60°,

90° x 40°, 90° x 90°

For short-to-medium throw applications like gyms

and small seating areas.

RMG-200A

Voice-range horn system

400 Hz to 8 kHz

MF 1 x 2"

75W RMS, 120W PGM, 11 ohms

For voice-range announcement.

RSH-462

Exponential FocusedArray™ horn system

400 Hz to 8 kHz

MF 4 x 2"

300W RMS, 750W PGM, 11 ohms

For voice-range announcement and

high-level paging.

R6-51

Three-way, full-range

50 Hz to 16 kHz

LF 6 x 12", MF 6 x 2", HF 6 x 1"

LF: 1200W RMS, 4 ohms

MF: 450W RMS, 8 ohms

HF: 300W RMS, 8 ohms

For high-level, very long throw

full-range reinforcement.

R6-Basshorn

Basshorn 6 x 12"

45 Hz to 500 Hz

1200W RMS, 3000W PGM, 4 ohms

For high-level, very long throw low

frequency reinforcement.

Three-way, full-range, 70 Hz to 16 kHz

LF 2 x 12", MF 1 x 2", HF 1 x 1"

(Model R2-52Z features MF 2 x 2")

400W RMS, 1000W PGM, 4 ohms

Available coverage patterns: 50° x 20°,

70° x 70°, 90° x 40°, 40-70° x 40°, 60-90° x 40°

For short-to-long throw applications requiring full

bandwidth reproduction.

R2SUB

Subwoofer, 30 Hz to 500 Hz

LF 2 x 12"

400W RMS, 1000W PGM, 4 ohms

For powerful low frequency reinforcement.

R.5COAX

Two-way, full-range, 80 Hz to 18 kHz

LF 1 x 12", HF 1 x 1"

200W RMS, 500W PGM, 8 ohms

Available coverage patterns: 60° x 60°, 90° x 90°

For short-throw applications such as concession

areas, gyms and as fill speakers.

R.5HP

Three-way, full-range, 85 Hz to 16 kHz

LF 1 x 12", MF 1 x 2", HF 1 x 1"

200W RMS, 500W PGM, 6 ohms

Available coverage pattern: 60° x 40°

For high level speech reinforcement and music

reproduction.

R.5SUB

Subwoofer, 45 Hz to 150 Hz

LF 1 x 12"

200W RMS, 500W PGM, 6 ohms

For near-field low frequency reinforce-

ment

Two-way, full-range, 90 Hz to 16 kHz

LF 1 x 12", HF 1 x 1"

200W RMS, 500W PGM, 8 ohms

Available coverage patterns: 60° x 40°,

60° x 60°, 90° x 94°

For medium-throw indoor and outdoor applications.

Community R-Series Application Guide — Page 3

The Community R-Series ...................................................................................................................... Page 2

Introduction to R-Series .................................................................................................................... Page 4-6

Installation, Application Notes and Safety ..................................................................................... Page 7-9

System Optimization ........................................................................................................................... Page 10

Throw Distance Chart ........................................................................................................................ Page 11

Baseball Field #1 ............................................................................................................................. Page 12-13

Baseball Field #2 ............................................................................................................................. Page 14-15

Baseball Field #3 ............................................................................................................................. Page 16-17

Small Football Field #1 .................................................................................................................. Page 18-19

Small Football Field #2 .................................................................................................................. Page 20-21

Small Football Field #3 .................................................................................................................. Page 22-23

Large Football Field #1.................................................................................................................. Page 24-25

Large Football Field #2.................................................................................................................. Page 26-27

Large Football Field #3.................................................................................................................. Page 28-29

High-School Gymnasium #1A ..................................................................................................... Page 30-31

High-School Gymnasium #1B ...................................................................................................... Page 32-33

High-School Gymnasium #2 ........................................................................................................ Page 34-35

High-School Gymnasium #3 ........................................................................................................ Page 36-37

Competition Indoor Swimming Pool ......................................................................................... Page 38-39

Outdoor Swimming Pool #1........................................................................................................ Page 40-41

Outdoor Swimming Pool #2........................................................................................................ Page 42-43

Outdoor Swimming Pool #3........................................................................................................ Page 44-45

Indoor Ice Rink #1 ......................................................................................................................... Page 46-47

Indoor Ice Rink #2 ......................................................................................................................... Page 48-49

Indoor Ice Rink #3 ......................................................................................................................... Page 50-51

Convention Center ........................................................................................................................ Page 52-53

Warehouse or Large Retail Store .............................................................................................. Page 54-55

Large Air-Inflated Structure ......................................................................................................... Page 56-57

City Street / Festival System ........................................................................................................ Page 58-59

NOTICE: Every effort has been made to insure that the information contained in this manual was complete and accurate at the time of printing.

However, due to ongoing technical advances, changes or modifications may have occurred that are not covered in this manual.

TABLE OF CONTENTS

Community R-Series Application Guide — Page 4

INTRODUCTION

Community’s R-Series is a high-quality, high-fidelity product line designed to be highly weather-resistant. R-Series products

perform consistently in continuous outdoor exposure while simultaneously providing superlative acoustic performance.

This Applications Guide discusses a variety of applications for R-Series loudspeakers. For each type of facility, we have

provided two or three different example designs with discussions about the merits of each design. Although the specific

facilities in this Guide are fictional, the designs shown are representative of typical R-Series applications and should be helpful

in designing sound systems for similar facilities.

Community emphasizes that these examples were created as guidelines only. They are not intended to be finished

designs and may or may not be suitable for specific projects. For a specific project, Community recommends the

services of a qualified acoustical consultant or design/build contractor.

For specific projects, Community’s TAG Team (Technical Applications Group) can provide additional product and applications

assistance and Community’s web site has additional resources including an “All-Weather/All-Purpose” Brochure describing all

R-Series and Wet Series II Models.

A DISCUSSION OF WEATHER-RESISTANCE

Weather-resistant is a relative term that describes a loudspeaker’s ability to resist the effects of weather in outdoor

applications. Typical weather-related damage encountered in loudspeakers affects the enclosure, drivers, hardware, and

internal components such as crossovers.

Community’s R-Series enclosures are fabricated entirely of hand-laminated fiberglass, or roto-molded gray polyethylene,

making them virtually impervious to weather-related effects. Fiberglass versions are coated with an attractive, light gray gel-

coat to help keep the loudspeaker cooler in sunlight. High-frequency drivers and their diaphragms are made of highly weather-

resistant materials. Midrange and low frequency cones are treated to repel moisture. All external hardware on the

loudspeaker is high-grade steel or aluminum with a weather-resistant, powder-coated finish. The grille is backed with a layer

of open cell foam supplemented by a fine mesh plastic to block rain or snow. This grille “sandwich” is acoustically transparent

but highly resistant to even driving rain. The perforated metal grille also keeps out insects and birds. There are no connectors

on an R-Series loudspeaker. Instead, a highly weather-resistant type 12’ (3.6 m) 16-2 SJOW cable is permanently attached to

the loudspeaker through a weather-tight gland nut. This connection is far superior to any exposed connector.

DESCRIPTION OF THE R-SERIES

All-Weather/All-Purpose

Though designed to handle the harshest outdoor conditions, R-Series is the perfect choice for many indoor environments.

With 22 models to choose from, ranging from short throw with wide coverage angles to ultra-narrow, long throw systems,

the task of designing an acoustically and economically effective sound system has never been easier. In many cases, a small

number of R-Series loudspeakers can provide top quality sound for a surprisingly large physical area, making them one of the

most acoustically and economically effective solutions available anywhere.

R-Series Applications

R-Series products are designed for permanent installation or portable use both outdoors and indoors. The primary

applications for Community’s R-Series are those where re-entrant horns, outdoor two-way horn/woofer loudspeakers, and

some larger horn loudspeakers typically are used but lack capability for both high quality music reproduction and longer

distance voice projection. By contrast, R-Series products have excellent fidelity and wide frequency range for both music

reproduction and voice projection.

R-Series products are ideally suited for athletic fields (football, soccer, baseball, tennis) and field houses, theme parks,

amusement parks, swimming pools, ski slopes, cruise ships, steeple carillons, fairgrounds, rodeos, small arenas, racing tracks,

air shows, skating rinks, convention centers, factories, warehouses, and portable sound systems. They can complement

Community WET Series II products for projects needing a combination of both longer and shorter-throw applications.

INTRODUCTION

Community R-Series Application Guide — Page 5

R-Series Indoor Applications

R-Series and WET Series II loudspeakers are great indoor loudspeakers. These models are ideal for humidity-prone

environments like gymnasiums and swimming areas. Selected models are available in specially-designed indoor versions without

the weather-resistant grille. Where likelihood of splashing (indoor water park) or physical abuse (gymnasium) is possible,

Community recommends the standard R-Series model with the grille.

R-SERIES FEATURES

R-Series products are entirely constructed of corrosion-resistant materials like fiberglass, powder-coated steel or aluminum,

non-metallic and carbon fiber, using sophisticated technologies to ensure they will withstand exposure to harsh environmental

conditions.

Weather-Resistant LF Cones and HF Diaphragms

All R-Series models feature weather-resistant LF cones and HF diaphragms.

Ferrofluid

Most LF, MF & HF drivers use Ferrofluid in their voice coil gaps. Ferrofluid provides improved heat transfer resulting in higher

power handling, reduced distortion from fluidic dampening of mechanical resonance, and it seals the air gaps against corrosion

and oxidation.

Driver Protection

Functioning as a limiter, Community’s exclusive DYNA-TECH™ protection circuitry found in many R-Series models provides

precise and repeatable protection by reducing excessive power to the drivers. In other models PowerSense™ DDP (Dynamic

Driver Protection) protection circuitry is built into the crossover to provide protection against excessive current.

Fiberglass or Polyethylene Horns and Enclosures

Horns and enclosures on larger R-Series models are constructed of hand-laid fiberglass. Fiberglass is inherently weather-

resistant while exhibiting the strength, stiffness, and non-resonant characteristics needed to insure an acoustically inert

loudspeaker enclosure. Enclosures and horns for the R.5 and R.25 models are attractively molded from highly weather-

resistant polyethylene.

The unique curved shape of R-Series and WET Series II helps reduce standing waves within the enclosure for improved LF

performance. Outdoors, the rounded shape inhibits standing water and helps to diffract wind, which in turn reduces the wind

load on the supporting structure.

Horn Technology

Community is the originator and master of fiberglass horn manufacturing. The horns used in many WET Series II and R-Series

loudspeakers are constructed as one-piece, precision waveguides by hand-crafting on a precision mold using 100% hand-

laminated fiberglass. Balsa wood is embedded and laminated into the fiberglass at strategic points to create extremely strong,

double wall constructions which damp vibrations providing clean, resonant-free sound. In compact R-Series models, the horns

are constructed of high density polyethylene with reinforcing ribs to dampen vibrations. Perforations in the horn reduce

reflections from the LF driver while still providing optimum pattern control and acoustic loading for the high frequency driver.

Weather-Stop™ Grille

Each enclosure is fitted with Community’s proprietary Weather-Stop protective grille. The grille consists of an external

perforated, powder-coated steel panel, followed by a layer of open cell foam, and an inner layer of fine mesh plastic. This grille

assembly prevents water intrusion, while providing a high degree of acoustic transparency.

Powder-Coated Steel Hardware

Most hardware and fasteners are made of corrosion-resistant powder-coated steel or stainless steel.

Input Cables

To help maintain its weather-resistance properties, there are no connectors on an R-Series loudspeaker. Instead, input is via

an attached 12 ft (3.6 m) 16-2 SJOW-type neoprene jacketed cable (rated for outdoor use) with a weather-tight gland-nut.

INTRODUCTION

Community R-Series Application Guide — Page 6

Envirotech™ Technology

All internal circuitry is protected from the elements with our proprietary Envirotech coating which seals sensitive electronic

components against the effects of moisture and corrosion.

High-Performance Crossovers and Autoformers

R-Series models feature high-power, high-performance two-way and three-way passive crossover networks with over-current

protection circuitry. 70V/100V models use a 200W, high-performance autoformer with lower loss than a true transformer

(the R.5SUB-T subwoofer uses a high-performance true transformer).

Versatile Mounting Accessories

Weather-resistant, powder-coated steel yoke-style mounting brackets are included with most models, while a variety of

optional mounting kits are available for others.

R-SERIES MODELS

The R-Series family features 22 models that range in capability from short throw usage for local area fill (less than about 50

feet or 15m), to extremely long throw capable of reaching across an entire stadium (as much as 700 feet or 215m). A wide

selection of coverage angles and power output capabilities characterize this versatile product line. A small, single 12”

subwoofer (called the R.5SUB) and a much larger dual 12” subwoofer (called the R2SUBZ) are available to complement full-

range systems. A full, horn-loaded subwoofer/bass augmentation loudspeaker is available as model R6-Basshorn. Smaller R-

Series products are rotationally molded of polyethylene, while the larger models are made from hand-laid fiberglass. All models

are available in architectural light gray, but custom colors are also available

(call for price and delivery quote). All medium and

long throw R-Series systems feature horn loading in all frequency bands. The R2 is offered in three symmetric horn patterns

and two asymmetric horn patterns, and all models except R.5SUB, R6, RMG and RSH are equipped with internal protection

circuitry to guard against excessive power. Because of their versatility, performance and weather-resistant properties, R-

Series systems are found in many of the world’s pre-eminent motor speedways, sports venues, and convention centers.

R-SERIES AND WET SERIES II

WET Series II is a major upgrade to Community’s second weather-resistant loudspeaker product line. WET was designed for

exceptional musicality and speech intelligibility using premium components housed in attractive molded fiberglass enclosures

available in white or black.

Although the two lines overlap in application, Community’s R-Series is primarily designed for medium- and long-throw, voice-range

applications where WET loudspeakers are primarily designed for short- and medium-throw, musical applications. This provides the

designer with many opportunities for systems using both product lines.

Thus, Community recommends R-Series as the main loudspeaker systems for long-throw applications like sports stadiums and

we recommend WET Series II for distributed systems in water parks or ski resorts that feature continuous music. We

encourage designers to explore the highly effective end results that can readily be obtained by mixing and matching these two

product categories to best suit the design requirements.

R-SERIES ACCESSORIES AND OPTIONS

Mounting Yoke and Multi-Angle Aiming Strap

All R.25 and R.5 models include a pre-installed, powder-coated steel mounting yoke. A Multi-Angle Aiming Strap is included

with selected R-Series models to help keep the speaker aimed in the intended direction.

Other Rigging Accessories

Always purchase rigging accessories, including eyebolts and other mounting hardware, from a reliable supplier

who certifies their products for the intended application. For outdoor use or use in corrosive atmospheres (like

indoor swimming pools), make sure the rigging accessories are corrosion resistant. ATM Flyware, a division of Allen Products,

is an example of a rigging supplier that supplies certified products for professional audio installations www.atmflyware.com

Another example of a certified rigging products supplier is Polar Focus www.polarfocus.com

INTRODUCTION

Community R-Series Application Guide — Page 7

70-Volt, 100-Volt Autoformer

Transformer versions (“T” suffix) include an internal 200W, 70/100V autoformer or transformer. For 70V lines the input taps

are 200W, 100W, 50W and 25W. For 100V lines the taps are 200W, 100W and 50W.

Some models have a multi-wire input cable to select the tap (R.5Coax, R.5SUB, R.5HP, etc.). In this case, termination is usually

best made inside an appropriate electrical box (weatherized as needed) using standard wire splicing methods. Other versions

have a screwdriver-selectable switch accessible through a plug screw (R.25-94TZ & R.5xxTZ) which is accessed by removing

the plug. Rotate the switch to the appropriate stop (“click”) for the desired tap using a flat-head #1 screwdriver. Re-insert

the plug screw after adjusting the tap to maintain weather-resistance. Use caution not to over tighten the plastic plug screw

to avoid stripping the delicate plastic threads. For the R.25-94TZ, re-install the plug so that is flush with the exterior of the

cabinet to avoid undue pressure on the switch mechanism. For additional information, Community’s web site includes

specification sheets and a technical note on the design of 70-volt/100-volt distributed systems.

Custom Colors

All R-Series and WET Series II product may be ordered in custom colors to elegantly match their physical installation

environment. Please contact Community for a quote on cost and lead time.

Using Yoke Brackets

Community provides one yoke-type mounting bracket with every R-Series loudspeaker except the R6-51 and R6-Basshorn. In

most cases, this will be the preferred hardware for mounting these products. The yoke attaches to the sides of the cabinet

with the provided fasteners. It also includes an array of holes along the center strap of the yoke to fasten to structural points

deemed suitable by the installer and/or professional engineer.

Using Safeties

For some applications, the installing contractor or professional engineer might deem necessary (or advisable) that R-Series

cabinets be installed with a secondary means of attachment such as a safety cable. In fact, some local building codes and other

regulations may require safety cables, chains or other secondary supports due to seismic concerns, excessive wind loads, etc.

Be aware that safety attachment points should not be located at insert points on opposite sides of the cabinet in such a

manner that they present a significant force that pulls the insert points away from each other. All safety cables, chains, or other

restraining hardware shall be installed so that the line is taut and positioned to minimize dynamic loading (falling, bouncing,

swinging, etc.) in the event that the loudspeaker’s primary mount fails.

Community does offer in its catalog forged, rated eyebolts intended for rigging loudspeakers. However, these eyebolts are not

rated for outdoor use and the shank is too long for the threaded inserts on R.25 and R.5 loudspeakers. This length limitation

does not apply to the R1 and R2 loudspeakers. Using an eyebolt with too long of a shank will not permit the eyebolt shoulder

to properly seat against the exterior of the cabinet. Installers will need to procure appropriate hardware made from the

appropriate material and shank length to meet the needs of each application.

In some cases, forged, overhead rated shoulder eyebolts may be used as attachment points on the cabinet for safety cables

with some restrictions. The eyebolt must be screwed in and firmly seated (do not over tighten) with the shoulder of the

eyebolt making contact with the rubber washer on the exterior of the cabinet. A rubber washer shall be used between the

eyebolt and the cabinet to maintain weather resistance. Shims may be used between the eyebolt and the rubber washer to

position the eye so that it is in the same plane as the suspension cable or chain. Care must be taken to ensure that the safety

cable will not induce a load off-axis from the eyebolt’s threaded shank.

Hoist Rings provide a method of attachment which has advantages over eyebolts that permit more flexibility in regard to the

pull/load direction of the safety line, though at a higher cost. Hoist rings include a hinged “eye” which allows the load applied

to the cabinet threaded inserts to remain largely in shear, thus preserving the integrity of the insert point. The same

precautions should be taken to properly seat the hoist ring as when seating an eye bolt.

As with all aspects of mounting and rigging loudspeakers, the use of eyebolts, hoist rings, and other safety cabling hardware

should be included in a rigging plan approved by a professional engineer.

IMPORTANT: The mounting bolts that come installed in each R-Series enclosure must either be used to mount the

Accessory Mounting Yoke or they must remain in place. If the rigging fittings are not sealed, air leaks will occur in the

enclosure that will compromise the loudspeaker’s weather-resistance and its low frequency performance.

IMPORTANT: Eyebolts and other mounting hardware for outdoor usage with R-Series loudspeakers must be corrosion

resistant steel properly rated for the load weight.

INSTALLATION

Community R-Series Application Guide — Page 8

Custom Mounting Brackets

Custom brackets, made of corrosion-resistant, properly-rated steel may be used. When mounting the loudspeaker the bracket

should pull directly either in tension or shear on the mounting bolt. It is recommended that any custom bracket utilize two

mounting points on the opposite sides or top and bottom of the enclosure.

Mounting an R6-51 or R6-Basshorn

Mounting systems for large loudspeakers, like the R6-51 and R6-Basshorn, vary widely depending on the needs of the

facility. For this reason, Community does not supply a yoke, fasteners or any other mounting hardware with the R6-51 or

R6-Basshorn. The installing contractor must supply all such hardware and must design a secure mounting system for the

loudspeaker. Always use properly-rated, corrosion-resistant fasteners of an appropriate length, secured with washers, lock

washers and Locktite or other fastener-locking method. The overall mounting system must be approved by a licensed

P.E. (USA) or other certification professional (outside USA) before installation.

The R6-51 and R6-Basshorn have four primary mounting points, with ½” x 13-TPI stainless steel inserts, suitable for

suspension of the loudspeaker. Two are located on the back of the loudspeaker. One is on the top and one is on the

bottom. The R6-51 and R6-Basshorn also have 10 holes in the front enclosure flange which are not designed for primary

suspension usage or for safety-cable attachment. However, these front mounting holes may be used as supplemental mounting

points for support of the front of the loudspeaker. Note that, on the R6-51, there are three bolts on the top and the bottom

of the enclosure used to fasten the mid-high pack to the inside of the loudspeaker. These bolts are not suitable for suspension

or for safety-cable attachment.

For many applications, the top and bottom mounting points, used together, are sufficient for secure mounting of these

loudspeakers. When a safety-cable mounting point is required, one or both of the rear mounting points may be used. In

applications where the loudspeaker may be subjected to high wind loads or other unusual stresses, Community recommends

the loudspeaker be mounted from the top and bottom and at least one of the rear mounting points with the remaining rear

mounting point available for a safety cable. For additional support in these applications, design the mounting structure to

utilize the front mounting points as supplemental support. When possible, use all three mounting systems (top/bottom, rear,

front). When in doubt, consult with the same licensed P.E. or other certification professional who will approve the design.

Orienting an R-Series Loudspeaker

An R-Series loudspeaker has a definite top, bottom and sides. However, a 180 degree inversion will not affect the coverage.

When the top of the enclosure is up, the input cable gland-nut will be down and to your right when looking directly at the

front of the loudspeaker. Also, the manufacturer's label is on the top of the enclosure. Once the top is determined, you can

properly orient the loudspeaker for your particular application according to the specified coverage pattern. When installed

outdoors, Community recommends tilting an R-Series loudspeaker downwards at least 15° to allow water to drain from the

enclosure.

R-Series Throw Distance and Sound Levels

The chart on Page 11 helps answer the question, “how far can it throw?”. The chart shows the maximum distance at which a

given model can reach 96 dB SPL on the A Scale (speech range). Consider a high-school football stadium where the crowd

noise is 86 dBA. At the recommended distance, an R.25 or R.5 would provide 10 dB headroom above the crowd noise. Even

if the crowd noise reaches 90 dBA, the R.25 or R.5 would still provide 6 dB of headroom which is acceptable for voice paging

and announcement systems (use a limiter to avoid clipping).

In larger facilities, crowd noise can exceed 100 dBA. At motor racing events, racing noise can exceed 120 dBA near the track.

It is impractical and unsafe to try to page above these levels. It’s better to train announcers to wait till the crowd (or motor

noise) quiets down and to repeat the page.

Additional Notes on Weather-Resistance

• No loudspeaker is completely “weather proof”. However, Community R-Series loudspeakers are designed to withstand

continuous outdoor exposure for many years of operation.

• We recommend angling the R-Series loudspeaker at least 15 degrees downward so as to reduce the possibility

of rain and other precipitation compromising the performance of the loudspeaker.

• All mounting holes must be sealed off with the supplied bolts, washers, and rubber washers. If, for any reason, these bolts

must be removed, seal off the hole with silicone caulking or some other suitable weather-tight sealant. The rubber

washers supplied with the mounting bolts must always seat against the enclosure.

• The gland nut securing the loudspeaker cable to the enclosure is sealed at the factory. Do not attempt to remove this nut

or the weather-tight seal will be broken. If it is desired to replace the gland nut with a connector, the connector must be a

INSTALLATION

Community R-Series Application Guide — Page 9

weather-proof design, sealed to the enclosure with silicone caulk or some other suitable weather-tight sealant. Neutrik

models NLT4MP and NLT4FX are good choices for this purpose. When mounting, we recommend installing R-Series

with the gland nut at the bottom wherever possible. Always leave a “drip loop” so water will not migrate toward the

loudspeaker.

• The grille assembly is designed to prevent normal and wind-driven rain from directly entering the mouth of the

loudspeaker. The grille is not designed to withstand such things as being directly sprayed from a hose.

• If you use any hardware in place of the supplied steel screws, bolts, nuts, and washers supplied, it should also be made of

corrosion-resistant, properly-rated steel.

• Always use outdoor-rated cable. Always seal connections in a weather-tight electrical box. Community recommends

periodic inspections of installed rigging hardware to discover and repair any unexpected corrosion or damage.

IMPORTANT:

If the above instructions are not observed, the weather-resistant integrity of an R-Series loudspeaker

can be compromised. This can result in damage to or failure of the hardware or internal components.

NOTICE - STAINLESS STEEL GRILLE AND YOKE CORROSION: R-Series stainless steel yokes and grilles may

show surface corrosion when exposed to marine or other corrosive atmospheres. This corrosion is primarily a

cosmetic problem and does not present an immediate hazard. As an option, Community offers higher grade 316 alloy

stainless steel grilles and yokes for R-Series and WET Series II products. Contact the factory for pricing and delivery

information.

ARTIFICIAL ECHOES

Echoes, Normal and Artificial

Outdoors, it’s common for sound to reflect off a wall or building. If a listener hears this reflection at least 35 to 70

milliseconds (depending on level) after the original sound they will perceive it as an echo.

It’s possible to create an “artificial echo” by separating two loudspeakers far enough apart that a listener hears the second

loudspeaker at least 35 to 70 milliseconds after they hear the first loudspeaker. There’s no reflection here but the effect is the

same - an unwanted echo.

To avoid normal echoes, try to aim loudspeakers away from walls or buildings. To avoid artificial echoes, use a point source

or distributed design as illustrated in this Applications Guide. When it’s necessary to split the loudspeakers, try to avoid

overlapping coverage. That is, to the extent possible, each listener should hear only one loudspeaker.

The Announcer’s Echo

Imagine an outdoor system at a sports facility where the announcer is located 35 to 70 feet (11m-21m) or more from the

loudspeakers. The announcer will hear his or her own voice. Then, about 35 to 70 milliseconds later, the announcer will hear

their own voice again as an echo! Although a broadcast professional or other trained announcer may be able to ignore this

echo, most people find it difficult to speak in this situation. To minimize the problem, close the window in the announcer’s

booth. Alternatively, give the announcer a local monitor loudspeaker or a set of headphones so he can hear his own voice

strongly. This masks the echo and minimizes the distraction.

This same problem occurs for an announcer on the field in a sports facility. Use a monitor loudspeaker or headphones, as

described above, to minimize this problem.

FOR MORE INFORMATION

For more information on installing and operating your R-Series loudspeakers, please refer to Community’s web site at:

www.communitypro.com

For applications support, service or warranty information, refer to Community’s web site or contact Community at

610-876-3400 / 1-800-523-4934.

COMMUNITY’S TECHNICAL APPLICATION GROUP (TAG)

Contact Community’s “TAG Team” (Technical Applications Group) for applications support on systems that use R-Series and

other Community loudspeakers. Our TAG Team can help choose the right product for each system and assist in system

design, loudspeaker layout, acoustic simulation analysis and provide information needed for system commissioning.

Contact the TAG Team at 610-876-3400 / 1-800-523-4934 or email TAGTEAM@communitypro.com.

INSTALLATION

Community R-Series Application Guide — Page 10

SYSTEM OPTIMIZATION

CHOOSING THE RIGHT LOUDSPEAKERS

AND ELECTRONICS

Choose R-Series models with high enough maximum SPL to provide the needed SPL at the farthest listener with an

appropriate headroom. Typical headroom factors are at least 6 dB for voice paging, at least 10 dB for voice reinforcement and

at least 20 dB for music reinforcement.

Choose R-Series models with the right frequency response for the application. Subwoofers will improve the sound quality of a

music reinforcement system but may reduce intelligibility in a voice-only system in a reverberant space.

Choose R-Series models with the right coverage patterns to cover the audience evenly. Point the loudspeakers at the

listeners and away from walls and ceilings or outdoor obstructions.

In outdoor applications, loudspeakers may be far enough apart to create artificial echos in areas of overlapped coverage.

Ideally, put all loudspeakers in a central location (central cluster design) or use a distributed system design to minimize this

problem. In any case, minimize overlap when loudspeakers are separated by more than approximately 40 feet.

Choose power amplifiers large enough to provide the desired power output with enough headroom to avoid clipping. Use a

limiter and high-pass filter to protect the loudspeakers. Follow proper wiring design and adjust gains and levels to minimize

hum and noise.

COMMISSIONING THE SYSTEM

Commissioning is the process of optimizing the performance of the system after it has been installed. There are several steps

in commissioning including verifying the proper operation of each system component and adjusting system gains and levels.

The last step in system commissioning is known as system equalization or “voicing.” Equalization is the process of adjusting

the frequency response of the system to optimize voice intelligibility or musical sound quality (or both). Note that R-Series

loudspeakers are factory voiced to optimize their speech intelligibility and musical sound quality. For this reason, many

designers find they can minimize overall system equalization and still achieve excellent voice intelligibility and musical sound

quality.

When equalizing an R-Series loudspeaker system the following points should be kept in mind to achieve the best results and to

avoid damaging the drivers.

1. Use only small amounts of equalization. In particular do not boost frequencies by more than about 3 dB. When

cutting frequencies more than 3 dB of attenuation is OK. Bear in mind that extreme frequency cuts will usually

result in less than optimum performance.

2. Do not attempt to boost any frequencies below 100 Hz with a graphic equalizer. Note that with the

recommended high-pass filter, moderate amounts of boost from a simple bass control are acceptable.

Community R-Series Application Guide — Page 11

THROW DISTANCE CHART

Community R-Series Application Guide — Page 12

BASEBALL FIELD #1

SEMI-DISTRIBUTED SYSTEM ON PRESS BOX

Center of press-box roof

is the best location for field

coverage loudspeakers.

DISCUSSION

When it’s possible to use a distributed system outdoors, the benefits are numerous. This design offers smooth and even

coverage of the seating areas with excellent sound quality and minimal neighborhood spill. The equipment cost is moder-

ate and installation is relatively easy. If the electronics rack can be located in the press box, cable lengths are probably

short enough to allow use of regular (vs. transformer) R-Series models which reduces total system costs.

The design is very flexible making it easy to add coverage for remote bleachers, concessions, player dugouts or the field

itself. Install the loudspeakers on a press box or centrally-located concessions stand. Alternatively, use the edge of a roof

over the bleachers. Consider protecting the loudspeakers from thieves and vandals if they are hanging low enough to

reach easily.

Field Coverage and Neighborhood Spill

R1s, located at the ends of the press box, can cover remote seating areas, a concession stand or player dugouts. The

press box distributed loudspeakers will provide some field coverage. When additional field coverage is needed, choose a

single loudspeaker location such as the center of the press box roof. If there’s a roof over the bleachers, install field cov-

R1 long-throw for distant

bleachers or concessions. For field

coverage, see “Discussion”.

Colors show sound level variation in audience

areas. Field, press box and other areas will

also receive sound (not shown).

R.5 short-throw for

bleachers or concessions.

Community R-Series Application Guide — Page 13

Qty Model Comments

2 R.5-66Z Used at each end of press box for left and right bleachers coverage

6 R.5-94Z Distributed along the overhang of the press box for bleachers coverage

2 R1-66Z Used at each end of press box for distant bleachers or concessions coverage

Based on cost comparison scale: $ = lower cost, $$$$$ = higher cost System Cost Estimate - $$

R.5

erage loudspeakers at the front (center) edge of the roof. Delay them, if necessary, to match the sound from loudspeak-

ers on the press box.

If there’s a light pole behind the press box, this is another potential location for field coverage loudspeakers. Install them

high enough to cover the field without overpowering listeners in the bleachers. Delay other loudspeakers as needed to

avoid an artificial echo.

A central location for field coverage loudspeakers will avoid the artificial echo problems created by a two-source design.

If it’s necessary to cover the field from two, widely separated loudspeaker locations, try to minimize the overlap in cover-

age. That is, aim the loudspeakers so their coverage patterns meet in the center of the field and use minimal overlap.

Feedback, Artificial Echoes and the Announcer Echo

A distributed system like this will not cause artificial echoes unless field coverage loudspeakers are remotely located or

split (see above). However, feedback is possible because the loudspeakers may be near the press box announce booth.

Provide a head-worn mic or just shut the window to minimize this problem. If the system includes field coverage, an an-

nouncer on the field will hear an “announcer’s echo”. See Page 9 for ways to minimize this problem.

Alternate Loudspeaker Choices and 70/100 Volt Systems

Add R.5SUB or R2SUBZ loudspeakers for extended low frequency response. If the electronics rack is remotely located,

most Community R-Series and WET Series loudspeakers are available in 70/100-volt versions. Higher-powered versions,

like the R1 or R2, can utilize optional, external 70/100-volt transformers. This makes it possible to use smaller loud-

speaker wire which helps reduce the overall system cost.

As a lower-cost design, substitute Community’s R.25-94Z (or TZ) for the R.5 models and our R.5-66Z for the R1-66Z.

This design will cover the audience well but at a lower level than the original design.

R-SERIES LOUDSPEAKERS USED IN THIS DESIGN

Community R-Series Application Guide — Page 14

DISCUSSION

When you can cover an entire facility from one location, a point-source system is almost always the most economical

choice. In this example, we’ve covered the entire bleachers area from a single light pole using only three R-Series loud-

speakers. The equipment cost is significantly lower than the previous distributed system and the design is easy to expand

for coverage of remote concessions, dugouts or the field itself. The lower equipment cost in this design will be somewhat

offset by an increased cost for installation and wiring. Also, this design doesn’t cover the seating area quite as evenly as

the distributed system and there will be more neighborhood spill. Often, these minor tradeoffs are easy to accept given

the reduction in cost.

Field Coverage and Neighborhood Spill

For field coverage, add an additional R2. R2s are available in a variety of coverage patterns for this purpose. To minimize

neighborhood spill, choose the loudspeaker location so the loudspeakers point away from the neighborhood. Also,

mount the loudspeakers high in the air and point them downward.

Colors show sound level variation in audience areas.

Field, press box and other areas will also receive sound

(not shown).

R2 for long-throw coverage.

R2/R1 for mid-throw coverage.

R.5 for short-throw coverage.

BASEBALL FIELD #2

POINT-SOURCE SYSTEM ON SINGLE LIGHT POLE

Community R-Series Application Guide — Page 15

Qty Model Comments

1 R2-94Z For coverage of the bleachers to the right of the pole

1 R2-52Z For coverage of the center bleachers and bleachers farthest from the pole

1 R.5HP For coverage of the bleachers nearest the pole

Based on cost comparison scale: $ = lower cost, $$$$$ = higher cost

System Cost Estimate—$$

Feedback, Artificial Echoes and the Announcer’s Echo

Feedback is unlikely in this system because the loudspeakers are a long distance from the microphone. There’s no chance

of artificial echoes in this design since all the loudspeakers are in one location. Real echoes are possible, of course, so try

to aim the loudspeakers away from any nearby walls or buildings. It’s also possible that an announcer in the press box will

hear an echo of his or her voice. The same problem can occur for an announcer on the field. See Page 9 for ways to

minimize these problems.

Alternate Loudspeaker Choices and 70/100 Volt Systems

Add R2SUBZ loudspeakers for extended low frequency response. Most Community R-Series and WET Series loud-

speakers are available in 70/100-volt versions. Higher-powered versions, like the R1 or R2, can utilize optional (external)

70/100-volt transformers. This makes it possible to use smaller gauge wire to the loudspeaker location which helps re-

duce the overall system cost.

As a lower-cost, alternative design substitute Community’s R1-94Z for the R2-94Z, the R1-64Z for the R2-52Z and an R.5

-66Z for the R.5HP. This alternative design will cover the facility well but will not reach “rock ‘n’ roll” levels.

R.5HP

R-SERIES LOUDSPEAKERS USED IN THIS DESIGN

Community R-Series Application Guide — Page 16

DISCUSSION

Community does not recommend a split cluster system of this design because it is very difficult to avoid artificial echoes. Some-

times, however, it’s just not possible to cover an entire ball park from a single loudspeaker location and there aren’t

enough loudspeaker locations to allow a proper distributed system design.

In this case, a split-cluster design may be the only solution. The problem with this design is the artificial echoes that will

be created in most locations. Any listener that is 35 to 70 feet (11m-21m) farther from one cluster than the other will

hear an echo. For example, consider a listener at Point A. Typically, this listener might be 50 feet (15m) from the left

cluster and 200 feet (60m) from the right cluster. Since sound travels 1100 feet per second (335m/sec), the listener at

Point A hears the sound from the right cluster 136 msec after he hears the sound from the left cluster. This long delay

will produce a distinct echo, even if the sound from the right cluster is as much as 10 dB lower in level than the sound

from the left cluster.

A listener at Point A will hear an echo

from the right-hand cluster.

Colors show sound level variation in audience

areas. Field, press box and other areas will

also receive sound (not shown).

BASEBALL FIELD #3

SPLIT POINT-SOURCE SYSTEM ON

TWO LIGHT POLES

R2 for long-throw coverage.

R1 for mid-throw

coverage.

This image is

correct for the

right-hand

pole. Use a

mirror-image

cluster for the

left-hand pole.

Community R-Series Application Guide — Page 17

Not all listeners will hear this kind of echo. For example, listeners near the center of the bleachers or the

center of the field will be equidistant from both clusters. These listeners will not hear an echo.

Field Coverage and Neighborhood Spill

This system will have some field coverage from the R2 loudspeakers aimed at the bleachers. For additional field coverage,

add an additional R2 at each pole. R2s are available in a variety of coverage patterns for this purpose.

Feedback, Artificial Echoes and the Announcer’s Echo

Listeners that hear only one cluster will not hear an echo. Thus, to minimize the problem of artificial echoes in this type of

system, aim the loudspeakers to cover one-half of the listening area with a very small overlap area. Community R-Series

loudspeakers have well-controlled coverage patterns to help achieve this goal. The “announcer echo” problem will also be

present in this system. Follow the recommendations on Page 9 to minimize this problem for announce-booth and field an-

nouncers.

Alternate Loudspeaker Choices and 70/100 Volt Systems

Add R2SUBZ loudspeakers for extended low frequency response. Most Community R-Series and WET Series loudspeakers

are available in 70/100-volt versions. Higher-powered versions, like the R1 or R2, can utilize optional (external) 70/100-volt

transformers. This makes it possible to use smaller gauge wire to the loudspeaker location which helps reduce the overall

system cost.

Qty Model Comments

2 R1-94Z For coverage of the bleachers nearest the pole

2 R2-694Z For coverage of the field and bleachers farthest from the pole

Based on cost comparison scale: $ = lower cost, $$$$$ = higher cost

System Cost Estimate - $$

R-SERIES LOUDSPEAKERS USED IN THIS DESIGN

Community R-Series Application Guide — Page 18

SMALL FOOTBALL FIELD #1

DISTRIBUTED PLUS POINT-SOURCE SYSTEM ON

PRESS BOX

DISCUSSION

This is an excellent design for a small football stadium. It combines the best features of a distributed system (for the home

-team bleachers) and a point-source system (for the away-team bleachers). All of the loudspeakers are in one general

location which reduces installation costs and eliminates most artificial echoes. If the electronics rack can be located in the

press box, cable lengths are probably short enough to allow use of regular (vs. transformer) R-Series models which re-

duces overall system costs.

If the roof of the press box is less than about 20 feet (6m) above the heads of the nearest listeners, the R2-52Z used for

the away-team bleachers may be too loud in the home-team bleachers. Look for an alternate location for the R2-52Z

when this occurs. Sometimes, there’s a light pole behind the press box. This makes a good alternate location for the R2-

52. Mount the R2-52Z at least 20 feet (6m) above the heads of the nearest listeners (30 feet or 9m is better) and delay

the remaining loudspeakers, if necessary, to avoid artificial echoes.

Field Coverage and Neighborhood Spill

This system will have some field coverage from the loudspeakers aimed at both sets of bleachers. For additional field cov-

erage, add two R2s, one on each side of the central R2 and aimed at the two ends of the field. R2 loudspeakers are avail-

able in several coverage patterns for this usage.

Colors show sound level variation in audience

areas. Field, press box and other areas will also

receive sound (not shown).

R.25

R.5

Community R-Series Application Guide — Page 19

Qty Model Comments

1 R2-52Z For coverage of the away-team bleachers

1 R.5-94Z For coverage of the home-team bleachers right

1 R1-64Z For coverage of the home-team bleachers left

3 R.25-94Z For coverage of the home-team bleachers center areas

Based on cost comparison scale: $ = lower cost, $$$$$ = higher cost

System Cost Estimate - $$

There will be some neighborhood spill behind the away-team bleachers. To minimize this problem, put the R2-52Z as

high as possible and aim it down at the away-team bleachers. Delay the other loudspeakers to avoid an artificial echo.

Feedback, Artificial Echoes and the Announcer’s Echo

This type of system will not produce artificial echoes. Real echoes are still possible, of course, so try to aim the loud-

speakers away from any nearby walls or buildings.

An announcer in the press box will be near the loudspeakers and should not hear an artificial echo. If feedback is a prob-

lem, provide a head-worn mic or just shut the window.

An announcer on the field will hear a confusing “announcer’s echo”. See Page 9 for ways to minimize this problem.

Alternate Loudspeaker Choices and 70/100 Volt Systems

Add R2SUBZ loudspeakers for extended low frequency response. Most Community R-Series and WET Series loudspeak-

ers are available in 70/100-volt versions. Higher-powered versions, like the R1 or R2, can utilize optional (external)

70/100-volt transformers.

R.25

R.5

R-SERIES LOUDSPEAKERS USED IN THIS DESIGN

Community R-Series Application Guide — Page 20

SMALL FOOTBALL FIELD #2

POINT-SOURCE SCOREBOARD SYSTEM

DISCUSSION

When you can cover an entire facility from one location, a point-source system is almost always the most economical

choice. In this example, we’ve covered both sets of bleachers from the scoreboard using only two R-Series loudspeakers.

The equipment cost is significantly lower than the previous distributed system and the design is easy to expand for cover-

age of remote concessions or the field itself. The lower equipment cost in this design will be somewhat offset by an in-

creased cost for installation and wiring.

Feedback, Artificial Echoes and the Announcer’s Echo

There’s little chance of feedback in this design because the loudspeakers are a long distance from the announcer’s micro-

phone. Also, there’s no chance of artificial echoes in this design since all the loudspeakers are in one location. Real ech-

oes are possible, of course, so try to aim the loudspeakers away from any nearby walls or buildings. It’s also possible that

an announcer in the press box will hear an echo of his or her voice. And, it’s likely that an announcer on the field will

hear a confusing echo. See Page 9 for a discussion of these problems.

Field Coverage and Neighborhood Spill

This design provides some field coverage. To improve field coverage, add an additional R2. R2s are available in a variety

of coverage patterns for this purpose. Also, due to the location, aiming angle and power level of the loudspeakers,

Colors show sound level variation in

audience areas. Press box and other

areas will also receive sound (not

shown).

Page is loading ...

Community R.15COAX User guide

Related papers

Other documents