Vivotek FD8162 User manual

FD8162FD8162

2MP • Full HD • PIR • Focus Assist

VIVOTEK

2 - User's Manual

Table of Contents

Overview.......................................................................................................................................................4

Read Before Use ��5

Package Contents ��5

Symbols and Statements in this Document ��5

Physical Description ��6

Hardware Installation ��7

Network Deployment ��10

Software Installation ��12

Ready to Use ��13

Accessing the Network Camera .................................................................................................................16

Using Web Browsers ��16

Using RTSP Players ��18

Using 3GPP-compatible Mobile Devices ��19

Using VIVOTEK Recording Software ��20

Main Page ..................................................................................................................................................21

Client Settings ............................................................................................................................................26

Conguration ..............................................................................................................................................28

System > General settings ��29

System > Homepage layout ��31

System > Logs ��34

System > Parameters ��35

System > Maintenance ��36

Security > User Account ��40

Security > HTTPS (Hypertext Transfer Protocol over SSL) ��41

Security > Access List ��46

Network > General settings ��51

Network > Streaming protocols ��59

Network > SNMP (Simple Network Management Protocol)

��68

Media > Image ��69

Media > Video ��78

Media > Audio��82

PTZ > PTZ settings ��83

Event > Event settings ��86

Applications > Motion detection��99

Applications > DI and DO ��102

Applications > Tampering detection ��102

Recording > Recording settings ��103

Local storage > SD card management ��108

Local storage > Content management ��109

Appendix .................................................................................................................................................. 111

URL Commands for the Network Camera �� 111

VIVOTEK

User's Manual - 3

Technical Specications �� 179

Technology License Notice �� 180

Electromagnetic Compatibility (EMC) �� 181

VIVOTEK

4 - User's Manual

Overview

VIVOTEK FD8162 is an easy-to-use fixed dome network camera, featuring 2-Megapixel

or 1080p Full HD resolution with superb image quality up to 30 fps� As a true day/night

camera, the FD8162 features a removable IR-cut filter, maintaining clear images 24 hours

a day� With WDR enhancement, users can identify image details in extremely bright or

dark environments� It is especially suitable for monitoring wide open indoor environments

such as building entrances, airports or applications requiring accurate identification�

With high-performance H�264/MPEG-4/MJPEG compression technology, the FD8162

offers extra-smooth HD video quality� For installers, properly adjusting the focus of a

megapixel network camera can be difficult due to the image detail� To resolve this, the

FD8162 is equipped with a focus assist button to allow users to precisely adjust the camera

focus� Furthermore, the unique design of the one-step mount facilitates easy usage of the

FD8162, offering more flexible, hassle-free installation and maintenance�

Together with a PIR sensor for thermal detection, 802�3af compliant PoE, tamper detection,

Micro SD/SDHC card for on-board storage, video cropping and e-PTZ functionality, the

FD8162 is indisputably the top choice for reliable and high performance surveillance�

VIVOTEK

User's Manual - 5

Read Before Use

The use of surveillance devices may be prohibited by law in your country� The Network Camera is not

only a high-performance web-ready camera but can also be part of a exible surveillance system. It is

the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for

its intended use�

It is important to rst verify that all contents received are complete according to the Package Contents

listed below� Take note of the warnings in the Quick Installation Guide before the Network Camera is

installed; then carefully read and follow the instructions in the Installation chapter to avoid damage due to

faulty assembly and installation� This also ensures the product is used properly as intended�

The Network Camera is a network device and its use should be straightforward for those who have basic

networking knowledge� It is designed for various applications including video sharing, general security/

surveillance, etc� The Configuration chapter suggests ways to best utilize the Network Camera and

ensure proper operations� For creative and professional developers, the URL Commands of the Network

Camera section serves as a helpful reference to customizing existing homepages or integrating with the

current web server�

Package Contents

■ FD8162 - the Network Camera

■ Alignment Sticker

■ T10 Torx screwdriver / Screws / Plastic anchors

■ DC Power Cable

■ Quick Installation Guide / Warranty Card

■ Software CD

Symbols and Statements in this Document

i

INFORMATION: provides important messages or advices that might help prevent inconvenient

or problem situations�

NOTE: Notices provide guidance or advices that are related to the functional integrity of the

machine�

Tips: Tips are useful information that helps enhance or facilitae an installation, function, or

process�

WARNING! or IMPORTANT!: These statements indicate situations that can be dangerous or

hazardous to the machine or you�

Electrical Hazard: This statement appears when high voltage electrical hazards might occur

to an operator�

VIVOTEK

6 - User's Manual

Physical Description

General I/O Terminal Block

This Network Camera provides a general I/O terminal block which is used to connect external

input / output devices. The pin denitions are described below.

Pin Name

1 DC 12V-

2 DC 12V+

3 AC 24V_2

4 AC 24V_1

5 DI- (GND)

6 DI+

7 DO-

8 DO+ (+12V)

87654321

123 74 5 86

Ethernet

Micro SD Card

Audio InAV Out

Reset

Int.

NTSC

PAL

Ext.

Camera Front View

Camera Rear View

Light Sensor

Lens

Built-in

Microphone

PIR Sensor

Black Cover

IR LEDs

(18 units, effective up

to 15m)

Reserved

(18 units, effective up

to 15m)

(18 units, effective up

to 15m)

Focus Assist

Button

General IO Terminal

Block

Audio In

Audio/Video Out

Jumpers

Microphone

Video Output

internal

external

NTSC

60Hz

PAL

50Hz

internal

external

60Hz

PAL

1 2

Audio In

Audio/Video Out

Reset

NTSC

Reset

NTSC

Reset Button

Micro SD/SDHC

Card Slot

Reset

NTSC

Reset Button

Reset

Int.

NTSC

Reset Button

Int.

10/100BaseT

Ethernet

Audio In

10/100BaseT

VIVOTEK

User's Manual - 7

Hardware Installation

Use the included T10 Torx screwdriver to loosen screws on the sides of dome cover to remove it� You

should then jot down the MAC address printed on the bottom of the camera�

Remove the black cover as shown below so that you can ne-tune the focus and zoom the

camera later when the cabling is done�

50

5m

41

5m

Before installing your camera, make

sure the built-in PIR (Passive Infrared

Sensor) can be directed toward the

area of interest, where possible

intrusion may occur� (The sensitivity

of PIR sensor depends on the object

size and temperature differences

between the object and the background

environment�)

Dome Cover

Bottom of the Camera

Tilt Adjustment

Screw

Focus Ctrl

Zoom Ctrl

Top View

Side View

VIVOTEK

8 - User's Manual

DI/DO Diagram

Please refer to the following illustration for the connection method�

Hardware Reset

The reset button is used to reset the system or restore the factory default settings� Sometimes

resetting the system can return the camera to normal operation� If the system problems remain

after reset, press the reset button longer to restore the factory settings and install again�

Reset: Press and release the recessed reset button with a straightened paper clip� Wait for the

Network Camera to reboot�

Restore: Press and hold the recessed reset button for at least several seconds to restore� Note

that all settings will be restored to factory defaults�

SD/SDHC Card Capacity

This network camera is compliant with Micro SD/SDHC 32GB and other preceding standard SD

cards�

12V

+12V

Digital output

PIN 1

Power+12V

PIN 2

Digital input

PIN 3

Ground

PIN 4

12 3 74 5 86

Ethernet

Micro SD Card

Audio InAV Out

Reset

Int.

NTSC

PAL

Ext.

Reset Button

VIVOTEK

User's Manual - 9

1� Attach the alignment sticker to the ceilling/wall�

2� Through the two circles on the sticker, drill two pilot holes into the ceilling/wall�

3� The Network Camera can be mounted with the cable routed through the ceiling/wall or

from the side� If you want to feed the cable through the ceiling/wall, drill a cable hole A as

shown in the above picture�

4� Hammer the supplied plastic anchors into the holes�

5� Align the two holes on each side of the camera base with the two plastic anchors on the

ceilling/wall, insert the supplied screws to corresponding holes and secure them with a

screwdriver�

Wall Mount

Ceiling Mount

VIVOTEK

10 - User's Manual

Network Deployment

Setting up the Network Camera over the Internet

There are several ways to set up the Network Camera over the Internet� The rst way is to set

up the Network Camera behind a router� The second way is to utilize a static IP� The third way is

to use PPPoE�

Internet connection via a router

Before enabling the access to the Network Camera over the Internet, make sure you have a

router and follow the steps below�

1� Connect your Network Camera behind a router, the Internet environment is illustrated below�

Regarding how to obtain your IP address, please refer to Software Installation on page 12 for

details�

2� In this case, if the Local Area Network (LAN) IP address of your Network Camera is

192�168�0�3, please forward the following ports for the Network Camera on the router�

■ Secondary HTTP port

■ RTSP port

■ RTP port for audio

■ RTCP port for audio

■ RTP port for video

■ RTCP port for video

If you have changed the port numbers on the Network page, please open the ports accordingly

on your router� For information on how to forward ports on the router, please refer to your

router’s user’s manual�

3� Find out the public IP address of your router provided by your ISP (Internet Service Provider)�

Use the public IP and the secondary HTTP port to access the Network Camera from the

Internet� Please refer to Network Type on page 51 for details�

IP address : 192.168.0.3

Subnet mask : 255.255.255.0

Default router : 192.168.0.1

IP address : 192.168.0.2

Subnet mask : 255.255.255.0

Default router : 192.168.0.1

LAN (Local Area Network)

Router IP address : 192.168.0.1

WAN (Wide Area Network )

Router IP address : from ISP

Cable or DSL Modem

L

A

N (

Local Area Network)

R

o

u

t

e

r

I

P

a

d

r

e

s

:

W

A

N (Wide Area Network )

R

o

u

t

e

r

I

P

a

d

r

e

s

:

f

r

o

m

I

S

P

POWER

COLLISION

LINK

RECEIVE

PARTITION

1

2

3

4

5

Internet

VIVOTEK

User's Manual - 11

Internet connection with static IP

Choose this connection type if you are required to use a static IP for the Network Camera�

Please refer to LAN conguration on page 51 for details.

Internet connection via PPPoE (Point-to-Point over Ethernet)

Choose this connection type if you are connected to the Internet via a DSL Line� Please refer to

PPPoE on page 49 for details�

Set up the Network Camera through Power over Ethernet (PoE)

When using a PoE-enabled switch

The Network Camera is PoE-compliant, allowing transmission of power and data via a single

Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enabled

switch via Ethernet cable�

When using a non-PoE switch

If your switch/router does not support PoE, use a PoE power injector (optional) to connect

between the Network Camera and a non-PoE switch�

Power + Data Transmission

Non-PoE Switch

PoE Power Injector

(optional)

POW

ER

C

O

LL

I

S

ION

L

I

N

K

RE

CEIVE

PARTITIO

N

1

2

3

4

5

POW

ER

C

O

LL

I

S

ION

L

I

N

K

RE

CEIVE

PARTITIO

N

1

2

3

4

5

PoE Switch

VIVOTEK

12 - User's Manual

Software Installation

Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up

your Network Camera on the LAN�

1� Install IW2 under the Software Utility directory from the software CD�

Double click the IW2 shortcut on your desktop to launch the program�

2� The program will conduct an analysis of your network environment�

After your network environment is analyzed, please click Next to continue the program�

3� The program will search for all VIVOTEK network devices on the same LAN�

4� After a brief search, the main installer window will pop up� Double-click on the MAC address

that matches the one printed on the camera label or the S/N number on the package box label

Installation

Wizard 2

IW

2

General Connection (without PoE)

POW

ER

C

O

LL

I

S

ION

L

I

N

K

RE

CEIVE

PARTITIO

N

1

2

3

4

5

1� If you have external DI devices, make the connection from general I/O terminal block�

2� Ethernet, power, and other cables are user-supplied� Use a Category 5 Cross Cable when

Network Camera is directly connected to PC�

3� Connect either the DC or AC pins from the terminal block to a power outlet�

Ethernet

Switch

Pin1 & 2 DC 12V

Black

Red

Pin3 & 4 AC 24V

VIVOTEK

User's Manual - 13

to open a browser management session with the Network Camera�

Internet Explorer�

Ready to Use

1� A browser session with the Network Camera should prompt as shown below�

2� You should be able to see live video from your camera� You may also install the 32-channel

recording software from the software CD in a deployment consisting of multiple cameras� For

its installation details, please refer to its related documents�

0002D107258A

00-02-D1-07-25-8A 192.168.5.151 FD8162

VIVOTEK

14 - User's Manual

Based on the live image retrieved from the camera, adjust the camera lens to the desired view

angle:

1� Turn the lens module left and right�

2� Loosen the tilt adjustment screws on both sides of the camera and then turn the lens module

up and down� Upon completion, tighten the screws�

3� Turn the lens to adjust the image orientation�

1

3

2

Pan 350°

Rotate 350°

Tilt 65°

3-axis Mechanism Design

IMPORTANT! DO NOT over-tighten the controller

bars� Doing so will damage the camera lens module�

W

T

8

N

To adjust the zoom factor and focus range

1� Loosen the zoom controller and then adjust zoom factor by moving the controller left and

right� Upon completion, tighten the zoom controller screw�

2� Loosen the focus controller and then adjust focus range by moving the controller left and

right� Upon completion, tighten the focus controller screw�

VIVOTEK

User's Manual - 15

1� Align the notches on the inner side of the black cover with the rivets on the sides of the lens,

and then x the black cover.

2� If you choose to feed the cable through the ceiling/wall, arrange the cables neatly through

the cable hole A (not shown in the drawing)� If you choose to feed the cable from the side, re-

move plate B�

3� Attach the dome cover to the camera as the direction shown below� Tighten two screws from

the sides of the dome cover�

4� Finally, make sure all parts of the camera are securely installed�

1

B

3

2

A

IMPORTANT! Be ware of

the cable route!

Black Cover

Dome Cover

1� When mounting the camera, you can use the key hole slot at the bottom� The key hole slot

helps facilitate installation and a safe mounting� First fasten a pioneer screw to the wall/

ceiling� Mount the camera to the screw�

2� Use a pencil to mark the locations of the 3 permanent mounting holes�

3� When cabling and the initial adjustment is done, mount the camera by fastening screws to the

3 mounting holes�

Mounting Holes

Key Hole Slot

Pioneer Screw

VIVOTEK

16 - User's Manual

Accessing the Network Camera

This chapter explains how to access the Network Camera through web browsers, RTSP players,

3GPP-compatible mobile devices, and VIVOTEK recording software�

Using Web Browsers

Use Installation Wizard 2 (IW2) to access to the Network Cameras on the LAN�

If your network environment is not a LAN, follow these steps to access the Netwotk Camera:

1� Launch your web browser (ex� Microsoft

®

Internet Explorer, Mozilla Firefox, or Netscape)�

2. Enter the IP address of the Network Camera in the address eld. Press Enter�

3� The live video will be displayed in your web browser�

4. If it is the rst time installing the VIVOTEK network camera, an information bar will prompt as

shown below� Follow the instructions to install the required plug-in on your computer�

NOTE:

For Mozilla Firefox or Netscape users, your browser will use Quick Time to stream live

video. If you do not have Quick Time on your computer, please download Quick Time

from Apple Inc's website, and then launch your web browser.

VIVOTEK

User's Manual - 17

To enable the ActiveX

®

Controls for your browser:

1� Choose Tools > Internet Options > Security > Custom Level�

2� Look for Download signed ActiveX

®

controls; select Enable or Prompt� Click OK�

NOTE:

1. By default, your Network Camera is not password-protected. To prevent unauthorized

access, it is highly recommended to congure a password for your camera later.

For

more information about how to enable password protection, please refer to Security

on page 40

.

2. If you see a dialogue box indicating that your security settings prohibit running

ActiveX Controls®, please enable ActiveX Controls for your browser.

VIVOTEK

18 - User's Manual

3� Refresh your web browser, then install the ActiveX

®

control� Follow the instructions to

complete installation�

Using RTSP Players

To view the H�264/MPEG-4 streaming media using RTSP players, you can use one of the

following players that support RTSP streaming�

Quick Time Player

Real Player

As most ISPs and players only allow RTSP streaming through port number 554, please set the

RTSP port to 554� For more information, please refer to RTSP Streaming on page 60�

For example:

4. The live video will be displayed in your player. For more information on how to congure the

RTSP access name, please refer to RTSP Streaming on page 59 for details�

1� Launch the RTSP player�

2� Choose File > Open URL� A URL dialog box will prompt�

3� The address format is rtsp://<ip address>:<rtsp port>/<RTSP streaming access name for

stream1 or stream2>

rtsp://192.168.5.151:554/live.sdp

Video 16:38:01 2011/03/25

VIVOTEK

User's Manual - 19

Using 3GPP-compatible Mobile Devices

To view the streaming media through 3GPP-compatible mobile devices, make sure the Network

Camera can be accessed over the Internet� For more information on how to set up the Network

Camera over the Internet, please refer to Setup the Network Camera over the Internet on page

10�

To utilize this feature, please check the following settings on your Network Camera:

1� Because most players on 3GPP mobile phones do not support RTSP authentication, make

sure the authentication mode of RTSP streaming is set to disable�

For more information, please refer to RTSP Streaming on page 60�

2� As the the bandwidth on 3G networks is limited, you will not be able to use a large video size�

Please set the video and audio streaming parameters as listed below�

For more information, please refer to Stream settings on page 78�

Video Mode MPEG-4

Frame size 176 x 144

Maximum frame rate 5 fps

Intra frame period 1S

Video quality (Constant bit rate) 40kbps

Audio type (GSM-AMR) 12.2kbps

3� As most ISPs and players only allow RTSP streaming through port number 554, please set

the RTSP port to 554� For more information, please refer to RTSP Streaming on page 60�

4� Launch the player on the 3GPP-compatible mobile devices (e�g�, Real Player)�

5. Type the following URL commands in the URL eld.

The address format is rtsp://<public ip address of your camera>:<rtsp port>/<RTSP streaming

access name for stream 3>�

For example:

rtsp://192.168.5.151:554/live.sdp

VIVOTEK

20 - User's Manual

Using VIVOTEK Recording Software

The product software CD also contains recording software, allowing simultaneous monitoring

and video recording for multiple Network Cameras� Please install the recording software; then

launch the program to add the Network Camera to the Channel list� For detailed information

about how to use the recording software, please refer to the user’s manual of the software or

download it from http://www�vivotek�com�

Page is loading ...

Vivotek FD8162 User manual

This manual is also suitable for

Vivotek FD8162 User manual

Related papers

Other documents