Jenn-Air JB36REFXLB Installation guide

JENN-AIR_BOTTOMMOUNTBUILT-INREFRIGERATOR

CONGELADOR

ENLAPARTEINFERIORJENN-AIR_

REFRIGI_RATEURENCASTRI_AVECCONGI_LA'EUR

ENDESSOUSJENN-AII_

INSTALLATIONGUIDE

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

MANUAL DEINSTALACION

Si tiene preguntas respecto alas caracteristicas, funcionamiento, rendimiento, partes, accesorios o servicio tecnico, Ilame al:

1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En CanadA, Ilame al: 1-800-807-6777, o visite nuestro sitio de internet: www.jennair.ca.

GUIDED'INSTALLATION

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web & www.jennair.ca.

Table of Contents/[ndice/Table des matieres ...................................................................................... 2

_°JENN-AIRo

W10183782A

TABLEOF CONTENTS

REFRIGERATOR SAFETY ........................................................................... 3

36" MODELS ................................................................................................ 4

42" FRENCH DOOR MODELS .................................................................... 5

INSTALLATION REQUIREMENTS ............................................................. 6

Tools and Parts ......................................................................................... 6

Location Requirements ............................................................................. 6

Electrical Requirements ............................................................................ 7

Water Supply Requirements ..................................................................... 8

Tipping Radius .......................................................................................... 8

Product Dimensions ................................................................................. 9

Door Swing Dimensions ......................................................................... 10

Overlay Series Door Panel & Cabinetry Clearance

(36" [91.4 cm] Models) ............................................................................ 11

Overlay Series Door Panel & Cabinetry Clearance

(42" [106.7 cm] Models) .......................................................................... 13

Overlay Series Custom Panels ............................................................... 15

Custom Overlay Panel Dimensions ........................................................ 15

Euro-Style and Pro-Style ®Door Handle Kits .......................................... 17

Euro-Style and Pro-Style ®Custom Side Panels .................................... 17

Overlay Series Custom Side Panels ....................................................... 18

INSTALLATION INSTRUCTIONS ............................................................. 19

Unpack the Refrigerator ......................................................................... 19

Reduce Tipping Radius .......................................................................... 19

Move the Refrigerator into House .......................................................... 20

Install Anti-Tip Boards ............................................................................ 20

Connect the Water Supply ..................................................................... 21

Plug in Refrigerator ................................................................................. 22

Move Refrigerator to Final Location ....................................................... 22

Level and Align Refrigerator ................................................................... 22

Install Overlay Series Custom Panels .................................................... 23

Adjust Door(s) ......................................................................................... 24

Install Side Panel .................................................................................... 26

Install Base Grille .................................................................................... 27

Complete Installation .............................................................................. 27

Water System Preparation ..................................................................... 27

[NDICE

SEGURIDAD DEL REFRIGERADOR ........................................................ 28

MODELOS DE 36". .................................................................................... 29

MODELOS DE DOS PUERTAS CON CONGELADOR

EN LA PARTE INFERIOR, DE 42". ........................................................... 30

REQUlSlTOS DE INSTALAClON .............................................................. 31

Piezas y herramientas ............................................................................. 31

Requisitos de ubicaci6n ......................................................................... 31

Requisitos electricos ............................................................................... 32

Requisitos del suministro de agua ......................................................... 33

Arco de vuelco ........................................................................................ 33

Medidas del producto ............................................................................. 34

Medidas de oscilaci6n de la puerta ........................................................ 35

Espacio para el panel de la puerta de la serie Overlay y

para los armarios (modelos de 36" [91,4 cm]) ....................................... 36

Espacio para el panel de la puerta de la serie Overlay

y para los armarios (modelos de 42" [106,7 cm])................................... 38

Paneles a la medida de la Serie Overlay ................................................ 40

Dimensiones del panel recubierto a la medida ...................................... 40

Juegos de manijas para puertas de estilo europeo y Pro-Style ®.......... 42

Paneles laterales a la medida para el estilo europeo y Pro-Style ®........ 42

Paneles laterales a la medida para la Serie Overlay .............................. 43

INSTRUCCIONES DE INSTALACION ...................................................... 44

Desempaque el refrigerador ................................................................... 44

C6mo reducir el arco de vuelco ............................................................. 45

C6mo hacer entrar el refrigerador en la casa ........................................ 45

C6mo instalar los tableros antivuelco .................................................... 45

Conexi6n del suministro de agua ........................................................... 46

C6mo enchufar el refrigerador ............................................................... 47

C6mo mover el refrigerador a su ubicaci6n final ................................... 47

Nivelaci6n y alineamiento del refrigerador ............................................. 48

C6mo instalar los paneles a la medida para la Serie Overlay ............... 48

C6mo ajustar la(s) puerta(s) .................................................................... 50

C6mo instalar el panel lateral ................................................................. 52

C6mo instalar la rejilla de la base ........................................................... 52

C6mo terminar la instalaci6n .................................................................. 53

Preparaci6n del sistema de agua ........................................................... 53

TABLEDESMATIERES

SI_CURITI_ DU RI_FRIGI_RATEUR ........................................................... 54

MOD#LES DE 36". ..................................................................................... 55

MOD#LES AVEC PORTES A DOUBLE BATTANT DE 42". .................... 56

EXIGENCES D'INSTALLATION ................................................................ 57

Outillage et pieces .................................................................................. 57

Exigences d'emplacement ..................................................................... 57

Specifications 61ectriques ...................................................................... 58

Specifications de I'alimentation en eau.................................................. 59

Rayon de basculement ........................................................................... 59

Dimensions du produit ............................................................................ 60

Dimensions pour le pivotement des portes ........................................... 61

S6rie Overlay - Panneau de porte et placard -

dimensions et espace libre (modeles de 36" [91,4 cm]) ........................ 62

S6rie Overlay - Panneau de porte et placard -

dimensions et espace libre (modUles de 42" [106,7 cm]) ...................... 64

Panneaux personnalises de la s6rie Overlay .......................................... 66

Panneaux personnalises - Dimensions .................................................. 66

Ensembles de poignees de porte

style europeen et Pro-Style ®................................................................... 68

Panneaux lateraux personnalises

des style europ6en et Pro-Style ®............................................................ 68

Panneaux lat6raux personnalis_s de la serie Overlay ............................ 69

INSTRUCTIONS D'INSTALLATION ......................................................... 70

Deballage du refrigerateur ...................................................................... 70

Reduction du rayon de basculement ..................................................... 71

Faire entrer le refrig_rateur dans le domicile .......................................... 71

Installation de planches antibasculement .............................................. 71

Raccordement & la canalisation d'eau ................................................... 72

Brancher le r6frig6rateur ......................................................................... 73

Deplacement du r6frig_rateur a I'emplacement final ............................. 73

R6glage de I'aplomb et alignement du r6frig6rateur .............................. 74

Installation des panneaux personnalises de la serie Overlay ................ 74

Ajustement de la (des) porte(s) ............................................................... 76

Installation du panneau lat6ral ................................................................ 78

Installation de la grille de la base ........................................................... 78

Achever I'installation ............................................................................... 79

Preparation du syst_me d'eau ............................................................... 79

2

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

36"MODELS

Euro-Style Design

Features stainless steel wrapped doors with towel bar handles.

JB36SEFXRB JB36SEFXLB

Pro-Style s Design

Features stainless steel wrapped doors and heavy duty handles with

diamond-etched grip.

JB36PPFXRB JB36PPFXLB

Oiled Bronze Design

Features warm bronze and copper highlights that are accented by

sleek, stainless steel handles.

JB36REFXRB JB36REFXLB

Overlay Design

Uses custom-made panels and custom hardware for a seamless

appearance designed to blend with existing kitchen cabinetry.

JB36CXFXRB JB36CXFXLB

42" FRENCHDOOR MODELS

Euro-Style Design

Features stainless steel wrapped doors with towel bar handles.

JF42SEFXDB

Pro-Style s Design

Features stainless steel wrapped doors and heavy duty handles with

diamond-etched grip.

JF42PPFXDB

Oiled Bronze Design

Features warm bronze and copper highlights that are accented by

sleek, stainless steel handles.

JF42REFXDB

Overlay Design

Uses custom-made panels and custom hardware for a seamless

appearance designed to blend with existing kitchen cabinetry.

JF42CXFXDB

INSTALLATIONREQUIREMENTS

Isc nd

IMPORTANT:

• Installer: Leave Installation Instructions with the homeowner.

• Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local

electrical inspector's use.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Cordless drill • Torx®tT15 and T27 screwdrivers

• Drill bits • 1V32"nut driver

• Two adjustable • 3/8",V4",and W' open-end

wrenches wrenches

• Phillips screwdriver • %2"Allen wrench

• Small level • V4"and 5Ae"socket drivers

• Appliance dolly • Tape measure

• Utility knife

PARTS NEEDED:

Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See

"Installation Requirements" for more information.

Pro-Style ®and Euro-Style are shipped complete.

If you are connecting the water line directly to copper tubing

and not to a shutoff valve, you need a ferrule, a union, and a

V4"compression fitting.

The refrigerator can be recessed in an opening between cabinets

or installed at the end of a cabinet run using a side panel to

enclose the refrigerator.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

• Observe all governing codes and ordinances.

• It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

• Do not install in a location where the temperature will fall

below 55°F (13°C).

• Floor must support the refrigerator weight, more than 600 Ibs

(272 kg), door panels and contents of the refrigerator.

• Ceiling height must allow for side tipping radius. See "Tipping

Radius."

• Location should permit door to open fully. See "Door Swing

Dimensions."

• Location must permit top grille removal. See "Opening

Dimensions."

Opening Dimensions

To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. Ifthe solid soffit is

higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the

rear wall studs 80" to 90" (203 to 229 cm) above the floor. See

"Install Anti-Tip Boards" for more information.

NOTE: A clearance of W' (1.3 cm) must be maintained in front

of the refrigerator's side trim in order for the top grille to be

removed.

I"®TORX is a registered trademark of Textron Innovations Inc.

6

A grounded 3 prong electrical outlet should be placed within

4" (10.2 cm) of the right side cabinets or end panel. See

"Electrical Requirements" for additional information.

The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the

plumbing for the water line can come through the floor or the

back wall. See "Water Supply Requirements" for more specific

information.

0

831/2'' (212.1 cm) min.

843/4'' (215 cm) max.

to bottom of solid soffit

A

Width

(see chart following)

(10.2 cm)

77"

(196 cm)

6 ,I

(15.2 cm'

q--

(15.2 c

24"

(60.96 cm) min.

Model Width A (as shown above)

36 351/2"(90.2 cm)

42 411/2"(105.4 cm)

NOTE: Flooring under refrigerator must be at same level as the

room.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

IMPORTANT: Ifthis product is connected to a GFCI (Ground Fault

Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Food quality

and flavor may be affected. If nuisance tripping has occurred, and

if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, remove the top grille and turn the master

power switch to OFF or disconnect power at the circuit breaker

box.

When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control

to the desired setting.

• p y

All installations must meet local plumbing code requirements.

The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. The right-hand side is recommended. The access hole

through the cabinet must be within 1/2"(12.7 mm) of the rear

wall.

NOTE: If the water shutoff valve is in the back wall behind the

refrigerator, it must be at an angle so that the tube is not

kinked when the refrigerator is pushed into its final location.

+

1"

(2.54 cm)

24"

(60.96 cm) min.

6 ,I

(15.2 cm)

If the water shutoff valve is not in the cabinets, the plumbing

for the water line can come through the floor. A 1/2"(12.7 mm)

hole for plumbing should be drilled at least 6" (15.2 cm) from

the right or left hand side cabinet or panel. On the floor, the

hole should be no more than 1" (2.54 cm) away from the back

wall. See "Connect the Water Supply."

If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the

household temperatures will remain above freezing.

Do not use a piercing-type or 34e"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. Ifyou have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi

(207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

• If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed,

qualified plumber.

_ k,_J _,_,s;5_

Be sure there is adequate ceiling height to stand the refrigerator

upright when it is moved into place.

• The dolly wheel height must be added to the tipping radius

when a dolly is used.

• If needed, the tipping radius can be reduced. See "Reduce

Tipping Radius."

Side Tipping Radius (36" [91.4 cm] Models)

/

//

1

/

f

(

901/2''

A ......

_ -.q{-_ (229.9 cm)

A. Tip this side only.

8

SideTippingRadius(42"[106.7cm]Models)

/JJf [

/

//

/

I

/

93"

_-_ (236.2 cm)

.....,

A. Tip this side only.

Side View

The power cord is 84" (213 cm) long.

The water line attached to the back of the refrigerator is 5 ft

(1.5 m) long. Height dimensions are shown with leveling legs

extended 1/8"(3 mm) below the rollers.

"833/8''

(211.8 cm)

T

231/2''

(59.7 cm)

84" (213.4 cm)

Power Cord

Series

Overlay Design

Euro-Style or Pro-Style ®Design

*When leveling legs are fully extended to 1V4"(3.2 cm) below

rollers, add 1V8"(2.9 cm) to the height dimensions.

"31/2'' (6.9 cm)

A

251/8"(63.8 cm)

253/8'' (64.5 cm)

TopView

36" (91.4 cm) Models

351/4"

(89.5 cm)

T

25%"

(64.5 cm)

NOTE: Add up to 21Vie'' (6.74 cm) for the handles.

42" (106.7 cm) Models

411/4" _1

<-_ (105cm) _ I

t

253/8''

(64.5 cm)

'_JLJ

NOTE: Add up to 21Vie'' (6.74 cm) for the handles.

Front View

Width dimensions were measured from trim edge to trim

edge.

Height dimensions are shown with leveling legs extended V8"

(3 mm) below the rollers.

36" (91.4 cm) Models

< >

*83%"

(211.8 cm)

361/4'' (92 cm) _1

*When leveling legs are fully extended to 11/4"(3.2 cm) below

rollers, add 1V8"(2.9 cm) to the height dimensions.

42" (106.7 cm) Models

.....ZZZZZZZZZZZZZZZ:Z--_

( )

mllllllllllll llllllllllllllll ll 16 _,,_

421/4" (107.3 cm)_ I

*When leveling legs are fully extended to 1Y4"(3.2 cm) below

rollers, add 1Y8"(2.9 cm) to the height dimensions.

Door Swnc ,g D mess o h,s

The location must permit the door to open to a minimum of 90°.

Allow 41/2'. (11.4 cm) minimum space between the side of the

refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay

panels or custom handles.

To adjust the door swing, see "Adjust Door Swing."

36" (91.4 cm) Models

\ \ \

\ \ "-,

23 '1

(58 cm) -_

max.

(li l'cm)

59"

(150 cm)

42" (106.7 cm) Models

t

407/_6''

(102.7 cm)

131/2''

(34 3cm)

ax.

//:Ill ///\\ \ ,,,,,_x..\

//,,',,' i i ill \x\ ',,y\',

///./ Jl xxx \\\ ,,,, .x.

// ,,'," i', 9o°_/ \\'9o ° ',: ",', \\

? ,_ --._4 130° 130° _j _', ,',

441/4''

(112.3 cm)

10

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If

the refrigerator is to be installed close to the wall, see "Door Swing 90 °,' on next page.

Door Swing 110 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator

Side Trim

I

Hinge

®

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a

radius that is equal to at least half the

thickness of the panel if a 130° door swing is

desired. See "Adjust Doors."

era)\,

\

11/4"

(3.2 cm)

1/2"

(3.8 cm)

Panel

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

11

I

90 ° Door

Stop Position

O Hinge

Spacer Panel

Door Swing 90 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator

Side Trim

11

(2.5 cm)

3/4"

(1.9 cm)

1/ . i

/2 ,,

(1.3 cm)',

',

i i

,, ,,

Cabidetr_

1/2"

(1.3cm)

3/4"

1/4"(6.35 mm)

1/2"(1.3 cm)

3/4"(1.9 cm)

1" (2.5 cm)

0

<

m

(1.9cm)!

I 1"

(2.5ore)

11/4"

(3.2 cm)

11/2"

(3.8ore)

Allow a minimum of 41/2"(11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if

thicker custom panels or custom handles are used. Do not overlook baseboards.

12

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If

the refrigerator is to be installed close to the wall, see "Door Swing 90 °,' on next page.

Door Swing 110 °

Actual Size

,I

[

I

Hinge

Refrigerator to

Cabinetry Clearance

®

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a

radius that is equal to at least half the

thickness of the panel if a 130° door swing is

desired. See "Adjust Doors."

Refrigerator

Side Trim

%

11/4"

(3.2 cm)

1" (2.5 cm)

NOTE: Allow W'

(1.3 cm) clearance

between overlay

panel and cabinetry.

1/2"

(3.8cm)

Panel

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

13

,I

[

90 ° Door

Stop Position

O Hinge

®

O

"=l

Door Swing 90 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator

Side Trim

11

(2.5 cm)

3/4"

(1.9 cm)

1 II I

/2 ,,

(1.3 cm),,

; '

i

i i

,, ,,

Cabin_etr_

1/4" (6.35 mm)

1/2" (1.3 cm)

......... r......... 3/4" (1.9 cm)

i

___,a I

1/2"

(1.3 cm)

3/4"

(1.90m) i

I 1"

(2.5cm)

O

<

"=l

i

,<

"O

i

1" (2.5 cm)

11/4"

(3.2 cm)

11/2"

(3.8cm)

Allow a minimum of 41/2"(11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if

thicker custom panels or custom handles are used. Do not overlook baseboards.

14

Custom overlay panels allow you to blend the exterior of your

refrigerator into the overall kitchen decor and to use custom

handles for additional design flexibility.

The custom panels must have backer panels attached in order to

mount them to the refrigerator. It is most common to work with

three panels, as shown in the following graphic: a decorative

overlay panel, a 1/8"(3.18 mm) spacer panel or spacer strips and a

I/4"(6.35 mm) backer panel.

Overlay Panel

Spacer Panel

Backer Panel

5/8,,to 3/4,,

(15.88 to W'

19.05 mm) 1/8" (6.35 mm)

(3.18 ram)

I

Spacer Panel

Overlay Panel

Backer Panel

1

1" minimum

[ (2.54 cm). ......

/"

j :DoodGrille Trim

_-_ Offset Dimension

I

J

In some cases, your cabinet manufacturer may choose to work

with one panel routed for the different dimensions. Follow these

panel dimension and placement instructions to be sure that the

custom overlay panels will fit properly.

IMPC RTANT:

• For 36" (91.4 cm) models, the refrigerator door overlay panel

cannot exceed 50 Ibs (23 kg) and the freezer drawer overlay

panel cannot exceed 20 Ibs (9.1 kg).

• For 42" (106.7 cm) models, the refrigerator door overlay panel

cannot exceed 30 Ibs (13.5 kg) and the freezer drawer overlay

panel cannot exceed 25 Ibs (11.4 kg).

• The weight of the top grille overlay panel cannot exceed

10 Ibs (4.5 kg) for both models.

To minimize panel weight, you may use 2" (5.08 cm) spacer strips

around the perimeter in place of full-sheet solid spacer panels.

The spacer strips must be set in at least 1" (2.54 cm) from the top,

bottom and side edges of the backer panel. If you use spacer

strips, it is also recommended that you use two 2" (5.08 cm) strips

horizontally centered for added support.

(.,usom Ovet;ey l: nesso ss

Custom Overlay Panels (36" [91.4 cm] Models) Custom Backer Panels (36" [91.4 cm] Models)

34a/4''(88.27 cm) _ _ 33a/4"(85.73 cm) m Center

Backer

II I 6a/,6"---_-- [[ i Panel

71/4'' TOPGRILLEPANEL (15.72 cm)___._[, =_ ,= left to

(18.42 cm) Maximum Weight: 10 Ibs (4.5 kg) = right

_'Bottom Offset

%" (9.5 mm)

34a/4"

(88.27 cm)

511/8"

(129.86 cm)

20s/4"

(52.71 cm)

REFRIGERATOR DOOR PANEL

Maximum Weight: 50 Ibs(23 kg)

34a/4''

(88.27 cm)

FREEZER DOOR PANEL

MaximumWeight: 20 Ibs (9.1 kg)

f 3, 1 _:

< (87.00 cm)

491/8''

(124.78 cm)

--I

20sAc ''

(51.28 cm)

341/4''

(87.00 cm)

t

_ Bottom Offset

7A4'(11.1 mm)

Center

Backer

.............Panel

leftto

right

Bottom Offset

[

Center

'_ Backer

Panel

' [ left to

' ! right

|

1/4"(6.35 mm)

15

Custom Overlay Panels (42" [106.7 cm] Models) Custom Backer Panels (42" [106.7 cm] Models)

407_6 ''

(102.7 cm)

I

7v*'TI ToPGRILU PANEL

(18.4 cm)! j Maximum Weight: 10 Ibs (4.5 kg)

l

511/4''

(130.2 cm)

20" __ __ 20"

(50.8 cm) (50.8 cm)

REFRIGERATOR

DOOR PANEL

MaximumWeight:

30 Ibs (13.5 kg)

REFRIGERATOR

DOOR PANEL

Maximum Weight:

30 Ibs(13.5 kg)

[

511/4''

(130.2 cm)

T

201/4''

(51.4 cm)

!

407/_6 ''

(102.7 cm)

FREEZER DOOR PANEL

Maximum Weight: 25 Ibs (11.4 kg)

39%"

< (100.6 cm) "_

L d ____(15.9 cm)

Side Offset _ Bottom Offset

3/8"(9.5 mm) 1/2"(1.27 cm)

Side

Offset _"

3/16 II

(4.7 mm)

19%" --_

(49.85 cm)

493/16''

(124.93 cm)

Exterior

_"""""""Panel

extends

above

door.

Bottom

Offset

1/211

(1.27 cm)

._ Side

"< Offset

| 3/16 II

I (4.7 mm)

I

Bottom

Offset _

1/211 |

(1.27 em) i

I

.... =_f= =,l

| ........ |

| I

i 40"

I (101.6 cm)

|

197/8"

(50.48 cm)

/

= = = =_=

_t

|

I

|

Offset all sides

3/16"(4.7 mm)

Spacer Panels (All models)

NOTE: Spacer panels must be at least 1" (2.54 cm) from the top, bottom, and side edges of the backer panel.

3-Piece Grille Overlay Panel Configuration

TopView Side View

I

/

A. Offset dimension

B. ¼" (6.25 mm) Backer panel

C. _" (3.18 mm) Spacer panel

D. ¾" (1.92 cm) Decorative

overlay panel

"_"J'i ..............._ C

.........B

3-Piece Door Overlay Panel Configuration

/

B C D

A. Offset dimension

B. ¼" (6.25 mm) Backer panel

C. _" (3.18 ram) Spacer panel

D. _" (1.92 cm) Decorative overlay panel

1-Piece Overlay Panel Configuration

In some cases, your cabinet manufacturer may choose to work

with one panel routed for the different dimensions. Follow these

panel dimesions and placement instructions to be sure that the

custom overlay panels will fit properly.

16

....... #, ,_ _ _-,> _v_i >

All factory parts are available through your Jenn-Air dealer or by

calling Jenn-Air at 1-800-JENNAIR (1-800-536-6247). In Canada,

call 1-800-807-6777.

Follow the kit instructions for installing the door handles.

Series 36" Models 42" Models

Euro-Style #W10197087 #W10197088

Pro-Style ® #W10197089 #W10197090

I:U 0-o I({_ CII'¢;'./;J. y o

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed and the end of a cabinet run. You

may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of

installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions and

may not reflect the needed panel installation dimensions.

• The side panel should be a minimum of %" (1.27 cm) thick

to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on the rear wall.

Refrigerator

241/8''

(61.3 cm)

(60.3 cm)

231/2,,

(59.7 cm)

Side Trim

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add 7/3_"(5.6 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than V4"(6.35 mm) thick, rout the front

edge to allow the side panel to fit into the trim.

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

A m

2.

Attach the support board with a screw or adhesive that is

compatible with aluminum and wood.

Recessed Inset Installation Dimensions

1.

Measure the distance from point A (as shown) to back wall.

2. Rout the front edge of the support board or attach a V4"

(6.35 mm) board to hold the panel in the cabinet side trim.

(6.35 mm)

3/16"

(4.7 mm)

7_2"

(5.5 mm)

t

_3/32"(10 mm)

11/64"

(4.5 mm)

(15.7 mm)

17

Custom side panels may be needed when not enough space is Side Trim (36" [91.4 cm] Models)

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed and the end of a cabinet run. You

may choose an Inset or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

3/8"

(9.7 mm)

The width and height of a side panel are determined by the type of

installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions and

may not reflect the needed installation dimensions.

The side panel should be aminimum of W' (1.27 cm) thick

to avoid warping.

If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on the rear wall.

1/16"

(1.5 mm)

Refrigerator (36" [91.4 cm] Models)

Overlay

T

2311/16 ''

(60.16 cm)

Side Trim (42" [106.7 cm] Models)

3/8"

(9.7 mm)

Refrigerator (42" [106.7 cm] Models)

Overlay

233/8''

(59.40 cm)

3

(1.5 mm)

1/8"

(3.2 mm)

3_6"

(4.5 mm)

18

InsetInstallationDimensions

36" [91.4 cm] Models

1. Measure the distance from point A (as shown) to the back

wall. Add 1/32"(0.8 mm) to this measurement to allow the side

panel to fit into the trim.

(-

2. If the panel is more than 3/8"(9.5 mm) thick, rout the front edge

to allow the side panel to fit into the trim

42" [106.7 cm] Models

1. Measure the distance from point A (as shown) to the back

wall. Add 1/32"(0.8 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than 3/8"(9.5 mm) thick, rout the front edge

to allow the side panel to fit into the trim.

Recessed Inset Installation Dimensions

36" [91.4 cm] Models

1. Measure the distance from point A (asshown) to back wall.

A

2. Rout the front edge of the support board or attach a 3/8"

(9.5 mm) board to hold the panel in the cabinet side trim.

42" [106.7 cm] Models

1. Measure the distance from point A (as shown) to back wall.

2=

A m

Rout the front edge of the support board or attach a 3/8"

(9.5 mm) board to hold the panel in the cabinet side trim.

INSTALLATIONINSTRUCTIONS

ge ot

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

IM PORTANI"."

• Do not remove the film until the refrigerator is in its operating

position.

• All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

• Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating position.

1=

Remove and save the literature package bag taped to the side

of the refrigerator and the parts bag behind the grille. Remove

the four brackets (two on each side) that attach the shipping

base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the

refrigerator is in its final location.

2=

If necessary, reduce the tipping radius. See "Tipping Radius"

for ceiling height requirements or "Reduce Tipping Radius" for

step-by-step instructions. Ifyou do not need to reduce the

tipping radius, proceed to "Move the Refrigerator into House."

; ec (,ce ?ppng F{!<csds

Before bringing the refrigerator into the home, be sure there is

adequate ceiling height to stand the refrigerator upright. See

"Tipping Radius" in the "Installation Requirements" section for

more information.

If you do not have adequate ceiling height to stand the refrigerator

upright, the tipping radius can be reduced by removing the top

grille and side trims (see the following chart).

Model Reduced Tipping Radius

36 88" (223.5 cm)

42 881/2"(224.8 cm)

1. Grasp both ends of the top grille.

19

2. Push the top grille straight up; then pull straight out. Lay the 42" (106.7 cm) Models

grille on a soft surface.

3.

B A B

A. Top grille

B. Cabinet side trim

Remove the six screws attaching each cabinet side trim to the

refrigerator and remove the side trims.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

1=

Place an appliance dolly under the left side of the refrigerator

as shown. Be sure to protect the side trims and handles. Place

the corner posts from the packing materials over the trims and

handles as appropriate. Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles.

36" (91.4 cm) Models

2. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator

close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of

the refrigerator on the floor, stand the refrigerator upright and

then lower the right-hand side of the refrigerator to the floor.

Do not remove film or cover.5=

6.

Reassemble the trim and top grille after the dolly has been

removed from the refrigerator.

£sslctl A s,- Boc cs

.......... b

IMPOR'rAN1":

To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. Ifthe solid soffit is

higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

• It is recommended that board(s) be installed before the

refrigerator is installed.

• Board(s) must be long enough to fully cover the width of the

compressor cover.

• Locate the board(s) so the bottom surface(s) of the board(s)

is(are) 84" (213 cm) from the floor.

During installation, raise the refrigerator up so there is 1/4"

(6.35 mm) maximum between the top of the refrigerator and

the bottom of the anti-tip board(s). Do not crush the

compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to

229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x

81 cm) boards to wall studs behind refrigerator. Use six

#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws

must be screwed into the studs at least 11/2"(3.8 cm). The

board(s) must overlap the compressor cover.

20

Page is loading ...

Jenn-Air JB36REFXLB Installation guide

Jenn-Air JB36REFXLB Installation guide

in other languages

Related papers

Other documents