Contec BPC-1111 Owner's manual

BPC-1111 1

PCI Backplane with 10-Slots(PCI x 10)

BPC-1111 User's Manual

CONTEC CO., LTD.

Description

BPC-1111 is the Backplane board which have the 10 PCI slots. The Backplane board have one SBC(CPU

board) PCI Bus slots(PCI0(SBC)) and nine PCI Bus slots(P_PCI1 - P_PCI2 and S_PCI1 - S_PCI7).

Package Contents

- The BPC-1111 Backplane Board

- This User's Manual

- ATX Control 6pin Cable

Features

-1PCI(

SBC

) + 9 PCI slots

- Support for ATX and AT compliant power supply.

- The optional unit suitable for mounting.

Specifications

Item Specification

Correspondence bus PCI Bus

Number of slots *1 SBC(CPU board) PCI bus slot PCI0(CPU) x 1 *1

PCI bus slot (P_PCI1 - P_PCI2 & S_PCI1 - S_PCI7 ) x 9

Supply power +5VDC, -5VDC, +12VDC, -12VDC, + 3.3VDC (Only for ATX power)

Operating conditions 0 - 60 °C , 10 - 90% RH(No condensation)

Storage conditions -20 - 70 °C

Floating dust particles Not to be excessive

Corrosive gases None

Major dimensions (mm) 245.1(W) x 210.0(D)

Weight 375g

Installable chassis FA-UNIT-F11BE, FA-UNIT-M11BE, FA-UNIT-M11RFV, FA-UNIT-F11RFV

*1 The SBC(CPU board) must install it to the PCI0(CPU) slot.

BPC-1111 User's Manual

2 BPC-1111

Board Dimension

[mm]

CN7

JP3

CN6

FAN2

FAN1

CN3

CN2

CN1

236.2

215.9

210.5

139.7

94.0

78.7

73.7

33.0

15.2

12.7

23.1

210.0

201.9

165.1

142.3

10.2

41.3

245.1

BPC-1111 User's Manual

BPC-1111 3

Jumper Setting and Connectors

AT Power Supply Connector: CN1

Pin No.

1

2

3

4

5

6

7

8

9

10

11

12

Function

Power Good

+5V

+12V

-

12V

GND

-

5V

+5V

Suitable Housing : GTC6P-1(correspond)

Suitable Contact : PCK18-2TR9(correspond)

Maker : BURNDY

Option Cable

(One side is solder disposal.)

Model : PCA-6P2 CONTEC

Cable length 36cm(AWG#18), two

CN1

1

ATX Power Supply Connector: CN2

When used with an ATX-compliant power supply that supports remote power on/off, the CPU card can

turn off the system power through software control.

To enable soft-off control in software, advanced power management must be enabled in the Setup

program and in the operation system. When the system BIOS receives the correct APM command from

the operating system, the BIOS turns off power to the computer.

With soft-off enabled, if power to the computer is interrupted by a power outage or a disconnected power

cord, when power resumes, the computer returns to the power state it was in before power was interrupted

(on or off).

Pin No.

1

2

3

4

5

6

7

8

9

10

Function

+3.3V

-12V

GND

PON

GND

-5V

+5V

Pin No.

11

12

13

14

15

16

17

18

19

20

Function

+3.3V

GND

+5V

GND

+5V

GND

Power Good

+5VSBY

+12V

CN2

Suitable Housing : 39-01-2200 (correpond)

Suitable Contact : 5556 (correspond)

Maker : Molex

11 1

20 10

BPC-1111 User's Manual

4 BPC-1111

Power Supply Terminal: CN3

When you input the power supply from the CN1 or CN2 connectors, you can output +5V, -5V, +12V and

–12V power from the CN3 terminal. The maximum output current of each power supply is showed

bellow.

Specification of Power Supply Terminal

Voltage +5VDC +12VDC -5VDC -12VDC

Max. Current 2A 2A 2A 2A

However, the maximum supply current is depend on the power supply connected to CN1 or CN2.

Suitable Ring Tongue : WS0.5-3 (correspond)

Suitable Spade Tongue : WS0.5-3A (correspond)

Applicable Wire AWG#(mm

2

) : 26 - 22(0.2 - 0.5)

Maker : JST

Screw torque : 0.4N-m(Max.)

+5V

-5V

+12V

-12V

GND

3.63

6.35±0.05

[mm]

CN3

System FAN Connector: FAN1 / FAN2(CN5/CN4)

FAN1 and FAN2 are 3-pins header for the system cooling fan power connector. The fan must be a 12V

fan. Pin 2 is for +12V power supply.

1

2

3

CN4 / CN5

Pin No.

1

2

3

Function

N.C.

+12V

GND

Suitable Housing : 22-01-1034 (correspond)

Suitable COntact : 08-70-0057 (correspond)

Maker : Molex

ATX Power Control Connector: CN6

Pin No.

1

2

3

4

5

6

Function

PME#

GND

PBTN-IN

GND

PSOUT

+5V SBY

CN6

1

2

3

4

5

6

Suitable Housing: XHP-6 (correspond)

Suitable Contact : SXH-001T-P0.6 (correspond)

Maker : JST

ATX Power Button connector: CN7

Pin No.

2

1

Function

GND

PBTN

CN7

2

1

Suitable Housing : XHP-2 (correspond)

Suitable Contact : SXH-001T-P0.6 (conrrespond)

Maker : JST

BPC-1111 User's Manual

BPC-1111 5

ATX Power ON: JP3

Pin No.

3

2

1

Function

GND

PBIN

PSOUT

2-3 Short : Disable ATX power control and set the

ATX Power Supply ON always by push

switch

(use as AT Power Supply).(Default))

1- 2 Short : Enable ATX Power Control by push

switch

3

2

1

JP3

Connector Block Drawing

1

2

6

5

4

3

2

1

JP3

3 2 1

9+5VSBY

14 PON

ATX Power Connector

ATX Power ON/OFF Switch

GND

PBTN

+5VSBY : +5V Stanby Voltage supplied to CPU board.

PS_OUT : ATX Power Supply ON (Low Lebel) Signal from CPU board.

GND

PBTN_IN: Output Switch Signal (connected to CN7) to CPU board.

GND

PME# :

PME# signal is input to the CPU board. They are valid

only for the signals compatible with the CPU board

(See the CPU board manual).

[Connect to CPU board with 6pin Cable (included).]

CN6

CN7

CN2

BPC-1111 User's Manual

6 BPC-1111

Copyright

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this

document. The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an

omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear

in this document nor for results obtained by the user as a result of using this product.

Limited One-Year Warranty

CONTEC IPC Series are warranted by CONTEC CO., LTD to be free from defects in material and

workmanship for up to one year from the date of purchase by the original purchaser.

Repair will be free of charge only when this device is returned freight prepaid with a copy of the original

invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from

which it was purchased.

This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and

original boards. The warranty is not applicable if the device has been tampered with or damaged

through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in

which case repairs will be considered beyond the warranty policy.

BPC-1111 User's Manual

BPC-1111 7

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please

obtain a Return Merchandise Authorization Number (RMA) from the CONTEC group office where you

purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor

be liable for any incidental or consequential damages due to such defect or consequences that arise from

inexperienced usage, misuse, or malfunction of this device.

BPC-1111 User's Manual

BPC-1111

User’s Manual

CONTEC CO.,LTD. June 2005 Edition

3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan

Japanese http://www.contec.co.jp/

English http://www.contec.com/

Chinese http://www.contec.com.cn/

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD. [06272005]

[04072005] Management No. A-46-993

[06272005_rev2] Parts No. LYEQ651

Contec BPC-1111 Owner's manual

Contec BPC-1111 Owner's manual

Related papers

Other documents