PRINTED IN UNITED STATES OF AMERICA
WELLS BLOOMFIELD, LLC
2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439
telephone: 775-689-5707
fax: 775-689-5976
www.wellsbloomfield.com
REPLACEMENT PARTS LIST
BLOOMFIELD FAUCET p/n 82556
600
p/n 72683 Rev. B ECN-13394
I
600 071205 cps
1 of 2
PART NO DESCRIPTION
8551-100B WASHER, 7/16" EXTERNAL EMS
82573 HANDLE ONLY , RED PLASTIC
82575 SEAT CUP ONLY
82576 SERVICE KIT, FAUCET HANDLE
82680 JAM NUT ONLY, 1-16-20 Ni PLATED
82681 WASHER ONLY, 15/16" ID x 1-1/8"OD x 1/16" THICK SS
82682 CLIP ONLY , HANDLE RETAINING
84804 KIT, AERATOR REPLACEMENT
84870 KIT, AERATOR REPAIR
86398 BONNET ONLY
86399 STEM ONLY
DISASSEMBLY (see fig. 1)
AERATOR
1. Unscrew AERATOR CAP (3a) from FAUCET BODY (1a) using
a 7/8" open end wrench.
2. Remove RETAINING CLIP (2) from FAUCET BODY.
3. Remove AERATOR DISK (3b) form AERATOR CAP (3a) by
pushing from the bottom with a finger (see fig. 2, A and B).
4. Remove O-RING (3c) from AERATOR DISK by lifting from the
edge.
BONNET ASSEMBLY
1. Unscrew AERATOR CAP (3a) from FAUCET BODY (1a) using
a 7/8" open end wrench.
2. Remove RETAINING CLIP (2) from FAUCET BODY.
3. Unscrew BONNET (1f) from FAUCET BODY using a 1-1/16"
open end wrench while using a 3/4" open end wrench on the
FAUCET BODY as back-up.
4. Withdraw BONNET ASSEMBLY (parts 1b, 1c, 1d, 1e and 1f; and,
HANDLE (1g) from FAUCET BODY.
5. SEAT CUP (1b) is removed by working it off the knob at the end
of the STEM (1d) .
6. Remove PIN (1e) to release HANDLE (1g) from STEM.
ASSEMBLY (see fig. 2)
AERATOR
1. Install O-RING (3c) on AERATOR DISK (3b).
2. Insert AERATOR DISK in to AERATOR CAP (3a). Long end of
AERATOR DISK goes in first.
3. Hold RETAINING CLIP (2) in place on FAUCET BODY, then
screw in AERATOR ASSEMBLY. Tighten using a 7/8" wrench.
BONNET ASSEMBLY
1. Insert STEM (1d) thru SPRING (1c) and BONNET (1f). Hold
HANDLE (1g) in place and insert PIN (1e) .
2. Install SEAT CUP (1b). Be sure cup is fully seated on STEM.
3. Screw BONNET (1f) onto FAUCET BODY using a 1-1/16"
open end wrench while using a 3/4" open end wrench on the
FAUCET BODY as back-up.
CLEANING
AERATOR
1. Wash AERATOR CAP (3a), AERATOR DISK (3b) and
O-RING (3c) in warm water. Rinse with a food-safe sanitizer.
2. Allow components to air dry.
SEAT
1. If required to stop dripping, clean SEAT CUP (1b) and seat area
of FAUCET BODY.
2. Replace SEAT CUP if damaged.
REPAIR
1. Unscrew AERATOR ASSEMBLY from FAUCET BODY.
2. Replace AERATOR DISK (3b) and O-RING (3c).
3. Hold RETAINING CLIP (2) in place on FAUCET BODY, then
screw in AERATOR ASSEMBLY. Tighten using a 7/8" wrench.
Fig. 1 Faucet Disassembly
2 of 2
CLEANING AND REPAIR INSTRUCTIONS
1a
1b
1c
1d
1e
1f
1g
2
3a
3b
3c
(A) (B) (C) (D)
Fig. 2 Aerator Assembly
600 72683 Replacement Parts List Faucet 82556
-
1
-
2
Bloomfield 8793 User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Bloomfield 1088M User manual
-
Bloomfield 1091 User manual
-
-
-
Bloomfield 1012 User manual
-
-
-
-
Bloomfield 8542 User manual
-