Sunrise Medical Zippie Z-Bop User manual

Z-Bop

Improving People’s Lives

Owner’s Manual

Zippie

®

Z-Bop

SUPPLIER: This manual must be given to the rider of this wheelchair.

RIDER:

Before using this wheelchair read this entire manual and save

for future reference.

Mode d’emploi

Zippie

®

Z-Bop

FOURNISSEUR: Ce manuel doit être remis à l’utilisateur / utilisatrice de ce

fauteuil roulant.

UTILISATEUR / UTILISATRICE : Avant d’utiliser ce fauteuil roulant, lisez

entièrement ce manuel et conservez le pour le consulter ultérieurement.

Manual de

Instrucciones

Zippie

®

Z-Bop

DISTRIBUIDOR: Este manual debe ser entregado al pasajero de esta silla

de ruedas.

PASAJERO: Antes de usar esta silla de ruedas, lea este manual en su totali-

dad y guárdelo para futura referencia.

932213 Rev. C

2

ENGLISH

I. INTRODUCTION

USER WARNING

WARNING

Attention wheelchair users, do not operate this wheel-

chair without first reading the owner’s manual. If you do

not understand the instructions and warnings of this

owner’s manual please contact your dealer or qualified

technician before operating this Quickie wheelchair.

Failure to do so may result in damage and/or injury.

DEALER/TECHNICIAN WARNING

WARNING

Attention dealers and qualified technicians, do not

operate or service this wheelchair without first reading

this owners manual. If you do not understand the

instructions and warnings of this owners manual please

contact the Quickie Technical Service Department

before operating and/or servicing this Quickie wheel-

chair. Failure to do so may result in damage and/or

injury.

WARNING

In addition, power wheelchairs may contain printed cir-

cuit boards.

Careful attention should be given to the Printed Circuit

Board Handling Techniques insert supplied with the

chair.

Related Documents

Listed below are additional documents which are referenced in this

owners manual.

• Quickie QR Owners Manual

• Quickie Hand Held Programmer Owners Manual

• Quickie PC Setup-Up Station Owners Manual

• Quickie Enhanced Display Owners Manual

• Quickie Specialty Control Owners Manual

I. INTRODUCTION

SUNRISE LISTENS

Thank you for choosing a Zippie wheelchair. We want to hear your

questions or comments about this manual, the safety and reliability

of your chair, and the service you receive from your Sunrise suppli-

er. Please feel free to write or call us at the address and telephone

number below:

SUNRISE MEDICAL

Customer Service Department

7477 East Dry Creek Parkway

Longmont, Colorado 80503

(800) 333-4000 or (303) 218-4500

FOR ANSWERS TO YOUR QUESTIONS

Your authorized supplier knows your wheelchair best and can

answer most of your questions about chair safety, use and mainte-

nance. For future reference, fill in the following:

Supplier:_______________________________________________________________

Address: _______________________________________________________________

______________________________________________________________________

Telephone: _____________________________________________________________

Serial #: _______________________________________ Date/Purchased:_________

932213 Rev. C

3

ENGLISH

II. TABLE OF CONTENTS

I. INTRODUCTION ....................................................... 2

II. TABLE OF CONTENTS............................................. 3

III. YOUR CHAIR AND ITS PARTS .............................. 4

IV

. NOTICE - READ BEFORE USE

................................

5

V. EMI (ELECTROMAGNETIC INTERFERENCE) ...... 5

VI.

GENERAL WARNINGS

.............................................

7

A.Notice to User and Attendants ................................. 7

B. Weight Limit............................................................... 7

C.

Controller Settings..................................................... 7

D.EMI............................................................................. 7

E.

Safety Check-List ....................................................... 7

F. Changes & Adjustments............................................. 8

G.When Seated in a Parked Wheelchair........................ 8

H

.Environmental Conditions ......................................... 8

I.

Terrain ........................................................................ 8

J.

Street Use.................................................................. 8

K.

Motor Vehicle Safety.................................................. 8

L. Center of Balance ...................................................... 8

M.Transfers..................................................................... 9

N.Reaching or Leaning................................................... 9

O.Dressing or Changing Clothes ................................... 9

P. Obstacles ................................................................... 9

Q.Driving in Reverse or Moving Backward ................... 9

R. Ramps, Slopes & Sidehills........................................... 10

S. To Reduce the Risk of Falls, Tip-over or

Loss of Control .......................................................... 10

T. Ramps at Home & Work............................................ 10

U.Wheelchair Lifts ......................................................... 10

V. Curbs & Single Steps.................................................. 10

W.Stairs .......................................................................... 10

Z.Escalators ................................................................... 10

VII. WARNINGS: COMPONENTS & OPTIONS .......... 11

A.Anti-tip Tubes (Manual Carrier Only) ........................ 11

B. Armrests .................................................................... 11

C.Batteries..................................................................... 11

D.

Cushions..................................................................... 11

E. Fasteners.................................................................... 11

F

.

Footrests

....................................................................

11

G.Motor Locks............................................................... 11

H.On/Off Switch............................................................ 11

I.

P

neumatic Tires

.........................................................

11

J. Positioning Belts......................................................... 12

K.Push Handles.............................................................. 12

L.

Seating Systems

..........................................................

12

M.Upholstery Fabric ...................................................... 12

N.Suspension (Power Base Only).................................. 12

O.Wiring......................................................................... 12

P. Manual Tilt ................................................................. 12

Q.Transit Use ................................................................. 12

R. Transit Option ............................................................ 13

S.

Rear Wheel Locks...................................................... 13

T. Modified Seat Systems ............................................... 13

U.

Anti-

Tip Tubes (Rear Std) (Manual Carrier) ............... 13

VIII.

SET UP

, ADJUSTMENT & USE

................................

14

Notes ............................................................................. 14

T

ools Y

ou Will Need

......................................................

14

A.Battery Removal......................................................... 15

B. Power Base Seat Height Adjustment......................... 15

C.Power Base Seat Removal.......................................... 15

D.Power Base Shroud Removal..................................... 16

E.

Check-Out................................................................. 16

F. Backrest ..................................................................... 17

G.

Swing-Away Hangers ................................................. 17

H.Articulating Legrest .................................................... 17

I.

Elevating and 90° Elevating Legrest ........................... 17

J. Composite Footplate................................................. 18

K.Kids and Adult Angle Adjustable Footplate................ 18

L. Aluminum Footplate .................................................. 18

M.90° Footboard............................................................ 18

N.Platform Flip-Up Footplate........................................ 19

O.Height Adjustable Armrests....................................... 19

P. Joystick and Enhanced Display................................... 19

Q.

To Adjust the Height of the Joystick

or Enhanced Display.................................................. 20

R. Joystick or Enhanced Display Swing-Away

Retractable Mount ..................................................... 20

S. Wheel Locks .............................................................. 20

T. Anti-Tip Tubes– Rear (Manual Carrier)...................... 20

U.Seat Removal.............................................................. 20

V. Manual Carrier........................................................... 21

W.Check-Out................................................................. 21

IX. POWER BASE OPERATING GUIDE ....................... 22

A.Circuit Breakers......................................................... 22

B. Motor Locks............................................................... 22

C.Performance Control Settings ................................... 22

D.Quickie Hand Held Programmer

or Quickie PC Setup Station...................................... 22

E. Thermal Roll-Back...................................................... 23

F. Circuit Breakers......................................................... 23

G.joystick Assembly....................................................... 23

H.Enhanced Display....................................................... 24

I. Motor Locks............................................................... 24

X. BATTERIES.................................................................. 25

A.

Introduction

...............................................................

25

B. Battery Charger ......................................................... 25

C.Acid Burns.................................................................. 25

D.

Connecting Batteries in Battery W

ell......................... 25

E.

Charging Batteries

...................................................... 26

F. Disposing of Batteries ................................................ 26

XI.

MAINTENANCE

.........................................................

27

A.Notes ......................................................................... 27

B. Cleaning ..................................................................... 27

C.

Storage Tips

...............................................................

27

D.Battery Maintenance .................................................. 27

E. Pneumatic Tires ......................................................... 27

F

.

T

o R

epair or R

eplace a Tire

.......................................

27

G.Motor Brushes ........................................................... 28

H.Ordering Parts ........................................................... 28

I. Maintenance Chart..................................................... 28

J. Tools You Will Need .................................................. 28

XII. SUNRISE LIMITED WARRANTY............................. 29

FRANÇAIS................................................................... 30

ESPAÑOL..................................................................... 59

932213 Rev. C

4

ENGLISH

III. YOUR CHAIR AND ITS PARTS

1. Single-post, height-adjustable armrest

2. Controller joystick

3. Seat frame

4.

Front caster 6"

5. Rear stabilizing caster 5"

6. Swing-away with angle-adjustable

footplates

7. Angle-adjustable back

8. Battery deck lid

9. 10" drive wheels

10. Freewheel release

11. Caster Fork (front)

12. Caster Fork (rear)

13. Shroud

14. Readi-align caster assist (not shown)

W

eight

105 lbs (base), 35 lbs (seat)

140 lbs (base & seat w/out footplate or

batteries)

Drive Wheels

10" Mag: Standard airless insert,

option - pneumatic

Joystick

QR3-Btn (right-hand or left-hand mount)

Batteries

(2 deep cycle batteries required to

operate chair)

optional U1 Gel or 50 Ahr (AGM)

Battery Charger

Option - off board 8 AMP

Colors (all standard)

Standard - red, blue, champagne, black

Option - blue marble, pink carbon,

yellow carbon

Seat F

rame

Width: 10" - 18"

Depth: 13" - 20"

Footrest

Standard - swing-away with composite

footplates and heel loops.

Option - elevating legrests

Casters (front)

Standard - 6" solid

Casters (rear)

Standard - 5" solid

Armrests

Standard - fixed height, single post

Height-adjust, flip back (Seat Frame)

Single post, height-adjustable

(Seat Frame)

Suspension

Standard - all wheel independent

All features may not be available with some

chair setups or in conjunction with another

chair feature. Please consult your supplier

for more information. Your authorized sup-

plier can also provide you with more infor-

mation on accessories.

ZIPPIE Z-BOP

1

3

6

7

8

9

11

12

13

4

5

10

2

V. EMI (ELECTROMAGNETIC INTERFERENCE

V. EMI (ELECTROMAGNETIC INTERFERENCE)

WARNING

Heed all warnings to reduce the risk of unintended

brake release or chair movement:

1.

Beware of the danger from hand-held transceivers.

Never turn on or use a hand-held transceiver while

power to your chair is on. Use extra care if you believe

that such a device may be in use near your chair.

2.

Be aware of nearby radio or TV stations, and avoid

coming close to them.

3. If unintended movement occurs, turn your chair off as

soon as it is safe to do so.

A. WHAT IS EMI?

WARNING

1. EMI means: electromagnetic (EM) interference (I). EMI

comes from radio wave sources such as radio transmitters

and transceivers. (A “transceiver” is a device that both sends

and receives radio wave signals).

2.

There are a number of sources of intense EMI in your daily

environment. Some of these are obvious and easy to avoid.

Others are not, and you may not be able to avoid them.

3. Powered wheelchairs may be susceptible to electromagnetic

interference (EMI) emitted from sources such as radio sta-

tions, TV stations, amateur radio (HAM) transmitters, two

way radios, and cellular phones.

4. EMI can also be produced by conducted sources or electro-

static discharge (ESD).

932213 Rev. C

5

ENGLISH

IV. NOTICE– READ BEFORE USE

A. CHOOSE THE RIGHT CHAIR & SAFETY

OPTIONS

Sunrise provides a choice of many power wheelchair styles, sizes

and adjustments to meet the needs of the rider

. However, final

selection of a wheelchair rests solely with you and your health care

professional. Choosing the best chair for you depends on such

things as:

1.

Your size, disability, strength, balance and coordination.

2. Your intended use, and your level of activity.

3. The types of hazards you must overcome in daily use (in

areas where you are likely to use your chair).

4. The need for options for your safety and comfort (such as

positioning belts or special seat systems).

B. ADJUST CHAIR TO YOUR ABILITY

You need to work with your doctor, nurse or therapist, and your

supplier, to fit this chair and adjust the controller settings for your

level of function and ability.

C. REVIEW THIS MANUAL OFTEN

Before using this chair you, and each person who may assist you,

should read this entire Manual and make sure to follow all instruc-

tions. Review the warnings often, until they are second nature to

you.

D. WARNINGS

The word “WARNING” refers to a hazard or unsafe practice that

may cause severe injury or death to you or to other persons. The

“Warnings” are in four main sections, as follows:

1. V — EMI

Here you will learn about electromagnetic interference and

how it can affect your chair

.

2. VI — GENERAL WARNINGS

Here you will find a safety checklist and a summary of risks

you need to be aware of before you ride this chair.

3. VII — WARNINGS — COMPONENTS & OPTIONS

Here you will learn about your chair

. Consult your supplier

and your health care professional to help you choose the

best set-up and options for your safety.

4. XI — BATTERIES

Here you will learn about battery and charger safety, and how to

avoid injury.

Q-NOTE– Where they apply

, you will also find “Warnings” in other

sections of this Manual.

Throughout this owner’s manual and on the wheelchair you will

see the icons listed below to identify warnings and potential haz-

ards. It is important to read and understand all of them and under-

stand them.

WARNING! These warnings must be followed, failure to do

so may cause personal injury or may damage

the wheelchair.

PROHIBITED! Prohibited actions must never be per-

formed. Performing an action that is

prohibited can cause personal injury

or may damage the wheelchair.

Q-NOTE: Q-Notes are informative statements to help

further explain actions, warnings or product

detail.

ESD: Electrostatic Discharge has a potential to dam-

age printed circuit boards unless handled cor-

rectly. When the ESD symbol is shown through-

out the owner manual, use the Proper Handling

Techniques Insert supplied with the chair to

properly handle printed circuit board.

932213 Rev. C

6

ENGLISH

V.

2. The higher the immunity level, the less the risk of EMI. It is

believed that a 20 V/m immunity level will protect the power

wheelchair user from the more common sources of radio

waves.

3.

The configurations tested and found to be immune to at least

20 V/m are:

a. Zippie Z-Bop power wheelchair with a right-hand

mounted Quickie controller, highback seat, flip-back arm-

rests, solid flip-up footplate and U1 gel cell batteries.

b. Zippie Z-Bop power wheelchair with a right-hand

mounted Quickie controller, highback seat, flip-back arm-

rests, solid flip-up footplate and 40Amh gel cell batteries.

4. The following specialty import devices have an unknown

effect on the immunity level because they have not been

tested on the Zippie Z-Bop with the Quickie controller:

• Breath Control

•

Ribbon Switch

• Disc Switch

• Proportional Head Control

• Proportional Mini-Joystick/Chin Control

• Buddy Button

• Micro Light

• Penta Switch

• Wobble Switch

• ASL Head Array

• HMC Mini-Joystick

• Egg Switch

• Switch-It head Array

WARNING

Individuals with physical limitations requiring the use of

a specialty control input device known not to be

immune to 20V/m, or not known, should exercise extra

care around known sources of EMI.

WARNING

There is no way to know the effect on EMI if you add

accessories or modify this chair. Any change to your

chair may increase the risk of EMI. Parts from other

suppliers have unknown EMI properties.

F. REPORT ALL SUSPECTED EMI

INCIDENTS

WARNING

You should promptly report any unintended movement

or brake release. Be sure to indicate whether there was

a radio wave source near your chair at the time.

Contact: Sunrise Medical Customer Service

Department at (800) 333-4000.

B. WHAT EFFECT CAN EMI HAVE?

WARNING

1. EMI can cause your chair, without warning, to:

• Release its brakes

• Move by itself

• Move in unintended directions

If any of these occurs, it could result in severe injury to

you or others.

2. EMI can damage the control system of your chair. This could

create a safety hazard, and lead to costly repairs.

C. SOURCES OF EMI

WARNING

The sources of EMI fall into three broad types:

1. Hand-Held Transceivers:

The antenna is usually mounted directly on the unit. These

include:

• Citizens band (CB) radios

•

“Walkie-talkies”

• Security, fire and police radios

• Cellular phones

• Lap-top computers with phone or fax

• Other personal communication devices

Q-NOTE– These devices can transmit signals while they are on, even

if not in use.

2. Medium-Range Mobile Transceivers:

These include two-way radios used in police cars, fire trucks,

ambulances and taxi cabs. The antenna is usually mounted on the

outside of the vehicle.

3. Long-Range Transceivers:

These include commercial radio and TV broadcast antenna towers

and amateur (HAM) radios. Note: The following are not likely to

cause EMI problems: Lap-top computers (without phone or fax),

Cordless phones, TV sets or AM/FM radios, CD or tape players.

D. DISTANCE FROM THE SOURCE

WARNING

EM energy rapidly becomes more intense as you get

closer to the source. For this reason, EMI from hand-

held devices is of special concern. (See C.1) A person

using one of these devices can bring high levels of EM

energy very close to your chair without you knowing it.

E. IMMUNITY LEVEL

WARNING

1. The level of EM energy is measured in volts per meter (V/m).

Every power wheelchair can resist EMI up to a certain level.

This is called its “immunity level”.

932213 Rev. C

7

ENGLISH

VI. GENERAL WARNINGS

WARNING

Heed all warnings in this section. If you fail to do so a

fall, tip-

over or loss of control may occur and cause

severe injury to you or others.

A. NOTICE TO USER AND ATTENDANTS

WARNING

User

1. Before using this chair, you should be trained in its safe use

by your health care professional.

2. Every wheelchair is different. Take the time to learn the feel

of this chair before you begin riding.

3. Be aware that you must develop your own methods for the

safe use of this chair, that are best suited to your level of

function and ability.

4. Have someone help you practice bending, reaching and

transfers until you learn how to do them safely.

5. Never try a new maneuver on your own unless you are sure

it is safe.

6. Get to know the areas where you plan to use your chair.

Look for hazards

and learn how to avoid them.

7. Always wear a positioning strap.

8. Do not use a wheelchair if the joystick does not spring back

to the neutral position.

9. Do not use your wheelchair if the joystick boot is ripped or

damaged.

10. Do not try to tip this wheelchair without an attendant pres-

ent.

User and Attendants

1. When transferring the user in or out of the wheelchair never

use the footplate as a platform.

2. Do not lift this wheelchair by any parts that are removable,

doing so may result in damage to the wheelchair or injury to

the user

.

3.

Never try to stop or slow this wheelchair with the wheel

locks (if applicable). Wheel locks are designed to prevent the

chair from moving when stopped. They are not brakes.

4.

Always keep your hands and body parts clear of moving parts

to help prevent injuries.

Attendants

WARNING

Make sure you heed all warnings and follow all instruc-

tions in each section of this manual. Be aware that warn

-

ings that apply to the user also apply to you.

1. Do not stand or sit on any portion of this wheelchair.

1.

Y

ou need to work with the user

, and the user

’s doctor

, nurse

or therapist, to develop safe methods best suited to your

abilities and those of the user.

2.

T

o manually push the chair you must release the motor locks.

•

Make sure you have full control over the chair when you

release the motor locks. When you do so the chair will

not have brakes.

•

Make sure the chair is on level ground before you release

the motor locks.

B. WEIGHT LIMIT

WARNING

1. NEVER exceed the weight limit of 165 pounds (74.8 kilo-

grams), for combined weight of rider and items carried.

2. Never use this chair for weight training if the total weight

(rider plus additional weights) exceeds the weight limits out-

lined above.

3. Exceeding the weight limit is likely to damage the seat,

frame, or fasteners and may cause severe injury to you or

others from chair failure.

4. Exceeding the weight limit will void the warranty.

C. CONTROLLER SETTINGS

WARNING

Be aware that you may need to adjust the controller

settings of your chair to reduce the risk of a collision,

fall or tip-over.

1. Check and adjust the settings every six to twelve months (or

more often, if needed).

2. Consult your supplier to adjust the control settings immedi-

ately if you notice any change in your ability to:

• Control the joystick.

• Hold your torso erect.

• Avoid running into objects.

D. EMI

WARNING

Read Section V to learn about EMI. To reduce the risk

of unintended brake release or chair movement:

1. Never turn on or use a hand-held transceiver while power to

your chair is on. Use extra care if you believe that such a

device may be in use near your chair.

2. Be aware of nearby radio or TV stations, and avoid coming

close to them.

3. If unintended movement or brake release occurs, turn your

chair off as soon as it is safe.

E. SAFETY CHECK-LIST

WARNING

Before each use of this chair:

1. Make sure the chair operates smoothly. Check for noise,

vibration, or a change in ease of use. (They may indicate low

tire pressure, loose fasteners, or damage to your chair). If

you detect a problem, make sure to repair or adjust the

chair. Deferring repair or adjustment could increase the risk

for injury

. Y

our supplier can help you find and correct the

problem.

2.

Make sure batteries are charged. Green lights on charge indi

-

cator will light up when charge is full. Yellow lights indicate

battery charge level is getting low. Red lights indicate batter-

ies are in immediate need of charging.

3.

If your chair has anti-tip tubes, lock them into place (manual

carrier only).

932213 Rev. C

8

ENGLISH

VI.

WARNING

Extra caution should be used when employing the disc

switch or the pro

ximity head array as control devices.

These two devices are susceptible to malfunction when

wet.

I. TERRAIN

WARNING

1. This chair is designed for use on firm, even surfaces such as

concrete, asphalt and indoor flooring.

2. Do not operate your chair in sand, loose soil or over rough

terrain. Doing so may damage wheels, bearings, axles or

motors, or loosen fasteners.

J. STREET USE

WARNING

In most states, power chairs are not legal for use on

public roads. Be alert to the danger of motor vehicles

on roads or in parking lots.

1. At night, or when it is hard to see, use reflective tape on

your chair and clothing.

2. It may be hard for drivers to see you. Make eye contact with

drivers before you proceed. When in doubt, yield until you

are sure it is safe.

K. MOTOR VEHICLE SAFETY

WARNING

To date, the U.S. Department of Transportation has not

approved any tie down system for transporting this

wheelchair in a motor vehicle.

1. Never sit in this chair while in a moving vehicle. In an acci-

dent or sudden stop you may be thrown from the chair.

• Wheelchair belts are designed to position the rider

only and will not protect you in an accident; further

injury may result from the belts.

2. Always move to an approved vehicle seat. You must be

secured with proper motor vehicle restraints.

3. Never transport this chair in the front seat of a vehicle. It

may shift and interfere with the driver.

4.

Always secure this chair so that it cannot roll or shift.

L. CENTER OF BALANCE

WARNING

The point where this chair will tip forward, back or to

the side depends on its center of balance and stability.

The Center Of Balance Is Affected By:

1.

The seat height and seat angle.

2. A change in your body position, posture or weight distribution.

3. Using this chair on a ramp or slope.

4. The use of a back pack or other options, and the amount of

added weight.

T

o R

educe The Risk Of A Fall Or Tip-

Over:

1. Consult your supplier for information on modifications

authorized by Sunrise before you modify or adjust this chair.

Q-NOTE– You may need to make additional changes to correct the

center of balance.

F. CHANGES & ADJUSTMENTS

WARNING

Never use non-Zippie parts or make changes to your

chair unless authorized by Sunrise. (Doing so will void

the Warranty and may create a safety hazard).

1. If you modify or adjust this chair it may increase the risk of a

fall or tip-over.

2. Modifications to the chair, seating system, or other compo-

nents which are unauthorized by Sunrise constitutes remanu

-

facturing of the wheelchair

. This voids the warranty. The

rider then assumes all future liability for the wheelchair.

3. We recomment that you use anti-tip tubes until you adopt to

the change and are sure you are not at risk to tip over (man-

ual carrier only).

G. WHEN SEATED IN A PARKED

WHEELCHAIR

WARNING

1. Always turn off all power to your chair when you are parked,

even for a moment. This will prevent:

• Accidental movement from contact with the joystick by

you or others.

• Unintended brake release or movement from EMI

sources. (See Section V)

2. Make sure that persons who help you (for example, store

clerks) are aware of the joystick and do not touch it. If they

do, your chair may move suddenly when you do not expect it.

H. ENVIRONMENTAL CONDITIONS

WARNING

Your chair is not designed for use in a heavy rain storm,

or in snowy or icy conditions.

1. Contact with water or excessive moisture can cause an elec-

trical malfunction. The frame, motors and other chair parts

are not watertight and may rust or corrode from the inside.

To avoid a chair failure:

• Minimize exposure of your chair to a rain storm or very

wet conditions.

• Never take your chair into a shower, tub, pool or sauna.

• Do not use your chair in fresh or salt water (such as at

the edge of a stream, lake, or ocean).

• Make sure shroud cover and deck lid are secure.

• Replace joystick boot if it becomes torn or cracked.

•

Make sure all electrical connections are secure.

•

Dry the chair as soon as you can if it gets wet, or if you

use water to clean it.

2.

Proceed slowly and use extra care if you must operate your

chair on a wet or slick surface.

•

Do so only if you are sure it is safe.

• Stop if one or both main wheels lose traction. If this

occurs, you may lose control of your chair or fall.

• Never operate your chair on a slope or ramp if there is

snow

, ice, water or oil film present.

• When in doubt, have someone help you.

3. When not in use, keep your chair in a clean, dry place.

932213 Rev. C

9

ENGLISH

VI.

2. Use extreme care until you know the balance points of this

chair and how to avoid a fall or tip-over.

3. Use anti-tip tubes (manual carrier).

4. have someone help you until you know the balance points of

your chair and how to avoid tip-

over.

M. TRANSFERS

WARNING

It is dangerous to transfer on your own. It requires

good balance and agility. Be aware that there is a point

during every transfer when the wheelchair seat is not

below you. To avoid a fall:

1. Always turn off power before you transfer to or from your

chair. If you fail to do so you may touch the joystick and

cause your chair to move when you do not expect it.

2.

Make sure motor locks are engaged. This keeps the chair

from moving when you transfer.

3. Work with your health care professional to learn safe methods.

• Learn how to position your body and how to support

yourself during a transfer.

• Have someone help you until you are sure you can do a

safe transfer on your own.

4. Move your chair as close as you can to the seat you are

transferring to. If possible, use a transfer board.

5. Rotate the front casters until they are as far forward as possi-

ble.

6. Be careful of the foot platform. If you can, remove or swing

it out of the way.

• Never stand on footrests when you transfer. Doing so

may damage them or cause your chair to tip.

• Make sure your feet do not “hang up” or get caught in

the space between the footrests.

7. Make sure armrests do not interfere.

8. Transfer as far back onto the seat surface as you can. This

will reduce the risk that you will miss the seat or fall.

N. REACHING OR LEANING

WARNING

Reaching or leaning affects the center of balance of your

chair. If done improperly, a fall or tip-over is likely.

When in doubt, ask for help or use a device to extend

your reach.

To Reduce the Risk of injury and/or Damage to the Chair:

1.

Never reach or lean if you must shift your weight sideways

or rise up off the seat.

2. Never reach or lean if you must move forward in your seat

to do so. Always keep your buttocks in contact with the

backrest.

3. Never reach with both hands (you may not be able to catch

yourself to prevent a fall if you lose your balance).

4. Never try to pick up an object from the floor by reaching

down between your knees.

5. Never put pressure on the footrest while reaching. This may

cause the chair to tip if you lean too far

.

6. Never reach or lean over the top of the seat back. This may

damage the backrest and cause you to fall.

7.

Never reach or lean to the rear unless your chair has anti-tip

tubes locked in place (manual carrier).

IF YOU MUST REACH OR LEAN, DO SO AT

YOUR OWN RISK.

Remember to:

1. Move your chair as close as you can to the object you wish

to reach.

2.

Rotate the front casters until they are as far forward as possi-

ble. This makes the chair more stable.

Q-NOTE– To do this: Move your chair past the object you want to

reach, then back up alongside it. Backing up will rotate the casters

forward.

3. Turn off all power to your chair. If you fail to do so, you may

touch the joystick and cause your chair to move when you

do not expect it.

4. Firmly grasp an armrest with one hand. This will help to pre-

vent a fall if the chair tips.

O. DRESSING OR CHANGING CLOTHES

WARNING

Be aware that your weight will shift if you dress or

change clothes while seated in this chair. To make the

chair more stable, rotate the front casters until they are

forward and lock anti-tip tubes in place when applicable.

P. OBSTACLES

WARNING

Obstacles you may have to overcome in daily use

include door thresholds, lifts, ramps and hazards such as

potholes and broken pavement. These can damage your

chair and may cause a fall, tip-over or loss of control.

1. Be aware that thresholds are very dangerous. (Even a small

change in height may stop a caster wheel and cause your

chair to tip). You may need to:

• Remove or cover threshold strips between rooms.

• Install a ramp at entry or exit doors.

2. Keep your eyes moving when you ride; scan the area well

ahead of your chair.

3. Make sure the floor areas where you use this chair are level

and free of obstacles.

4. To help correct your center of balance:

•

Lean your upper body forward slightly as you go up over

an obstacle.

• Press your upper body backward as you go down from a

higher to a lower level.

5. If your chair has anti-tip tubes, lock them in place before you

go up over an obstacle.

Q. DRIVING IN REVERSE OR MOVING

BACKWARD

WARNING

Use e

xtra care when you drive your chair in reverse.

Y

ou may lose control or fall if one of the rear wheels

hits an object.

1.

Operate your chair slowly and at an even speed.

2. Stop often and check to make sure your path is clear of

obstacles.

3. If your chair has anti-tip tubes, make sure to lock them into

place.

932213 Rev. C

10

ENGLISH

VI.

U. WHEELCHAIR LIFTS

WARNING

Wheelchair lifts are used in vans, buses, and buildings to

help you move from one level to another.

1.

Always turn off all power to your chair when you are on a

lift. If you fail to do so, you may touch the joystick by acci

-

dent and cause your chair to drive off the platform. (Be

aware that a “roll-stop” at the end of the platform may not

prevent this).

2.

Make sure there is not a lip or drop-off at the top or bottom

of the platform. These may cause a fall or tip-over. When in

doubt, have someone help you.

3. Always secure the rider with a positioning belt to help pre-

vent falls during transfers.

4. Avoid moving forward if a wheel is “hung up” on the lip of

the ramp. Backup, reposition the caster for a more direct

approach and slowly try again.

V. CURBS & SINGLE STEPS

WARNING

1. It is recommended to climb and/or descend a curb, single step,

or other obstacle that a ramp or curb cutout is always used.

2. If you must climb or descend a curb, single step, or other

obstacle that is greater than 2.5", it is recommended to have

a person assist you in doing so.

3. In no case should you try to climb a curb, single step, or

other obstacle greater than 4" high.

4. If you must climb or descend a curb or step alone do so at

your own risk using extreme care and follow the following

procedure:

• Proceed slowly, at a steady speed

• Go as straight up or down as you can over the obstacle.

Never turn when trying to climb or descend and obstacle,

doing so may result in a fall or tip-over.

5. Failure to follow the above procedures may cause:

• A Fall or Tip Over

• Damage to the frame, wheels, axles or other parts, or

loose fasteners.

W. STAIRS

WARNING

Never use this chair to go up or down stairs, even with

an attendant. Doing so is likely to cause a fall or tip-over.

X. ESCALATORS

WARNING

Never take this chair on an escalator

, even with an

attendant. Doing so is likely to cause a fall or tip-

over

.

R. RAMPS, SLOPES & SIDEHILLS

WARNING

The center of balance of your chair changes when you

are on a slope.

Q-NOTE– “Slope” includes a ramp or sidehill. Your chair is less stable

when it is at an angle. Never use this chair on a slope unless you are

sure it is safe. When in doubt, have someone help you.

Beware Of:

1. Steep slopes. Do Not use this chair on a slope steeper than

10%. (A 10% slope means one foot in elevation for every

ten feet of slope length.)

2. Wet or slippery surfaces (such as when ice, snow, water or oil

film is present). A loss of traction may cause a fall or tip-over.

3. A change in grade on a slope (or a lip, bump or depression).

These may cause a fall or tip-over.

4. A drop-off at the bottom of a slope. (A drop-off of as small

as 3/4 inch can stop a front caster and cause the chair to tip

forward).

S. TO REDUCE THE RISK OF A FALL, TIP-

OVER OR LOSS OF CONTROL

WARNING

1. Never use your chair on a slope unless you are sure you can

do so without losing traction.

2. Always go as straight up and as straight down as you can.

• Do not “cut the corner” on a slope or ramp.

• Do not turn or change direction on a slope.

3. Always stay in the center of the ramp. Make sure ramp is

wide enough that you are not at risk that a wheel may roll off

the side.

4. Lean or press your body uphill. This will help adjust for a

change in the center of balance caused by the slope.

5. Keep your chair moving at a slow, steady speed. Keep control

over the chair at all times.

• On a descent, do not let your chair accelerate beyond its

normal speed.

• If the chair picks up speed, center the joystick to slow

down or stop.

• If you stop, re-start slowly.

T. RAMPS AT HOME & WORK

WARNING

Make sure ramps meet all Building Codes for your area.

1. For your safety, have a licensed contractor build or remodel

ramp to meet all standards.

Q-NOTE– The proper design will vary, depending on such things as:

the length and height of the ramp; the need for an intermediate

platform; landing size; doors and the direction of swing; and whether

the ramp includes a turn or angle.

At A Minimum:

1. Open sides of ramp must have side rails to prevent your

chair from going over the edge.

2. Slope must not be steeper than one inch in height for every

one foot of slope length.

3. Ramp surface must be even, and have a non-skid surface.

4.

Y

ou may need to add a section at the top or bottom to avoid

a lip or drop-off.

5. Ramp must be sturdy. Add bracing if needed, so ramp does

not “bow

” when you ride on it.

932213 Rev. C

11

ENGLISH

VII. WARNINGS: COMPONENTS & OPTIONS

WARNING

Note: If you use parts or make changes not authorized

by Sunrise it may create a safety hazard and will void

the Warranty.

A. ANTI-TIP TUBES

(manual carrier only)

Never remove or alter anti-tip tubes. They help keep your chair

from tipping over backward in normal use. Make sure rubber

rollers are in good condition.

B. ARMRESTS

WARNING

Armrests cannot be used to lift chair or the seat.

PROHIBITED!

1. Never lift this chair by its armrests.

2. Lift this chair only by non-detachable parts of the main frame.

C. BATTERIES

WARNING

1. Only deep cycle sealed case construction batteries should be

used in this device.

2. To prevent an acid spill, always keep batteries upright (wet

cell batteries only).

PROHIBITED!

1. Never smoke or hold an open flame near batteries. They are

a known explosion hazard.

2. Always wear rubber gloves and safety glasses when you han-

dle batteries.

3. Read all of section XI Batteries before attempting to change

or charge batteries.

4. Always remove batteries using straps or handle provided.

Pinched fingers may occur if the batteries are removed by

grasping the battery casings.

D. CUSHIONS

WARNING

If you suffer from pressure sores, or if you are at risk that they will

occur, you may need a special seat system such as can be provided

by the Seat F

rame, or a device to control your posture.

•

Consult your doctor

, nurse or therapist to find out if you

need such a device for your well-being.

E. FASTENERS

WARNING

Many of the screws, bolts and nuts on this chair are spe-

cial high-strength fasteners. Use of improper fasteners

may cause your chair to fail.

1. Only use fasteners provided by Sunrise.

2.

If fasteners become loose, tighten them as soon as you can.

3. Over- or under-tightened fasteners may fail or cause damage

to chair parts.

• See Section IX, “Set-Up, Adjustment & Use”, for proper

torque settings.

F. FOOTRESTS

WARNING

1. At the lowest point, the foot platform and footrests should

be at least 2 1/2" off the ground. If set too LOW, it may “hang

up” on obstacles you can expect to find in normal use. This

may cause the chair to stop suddenly and tip forward.

2. To avoid a trip or fall when you transfer:

• Make sure your feet do not “hang up” or get caught in

the space surrounding or in between the footrests.

•

Avoid putting weight on the footrests, as the chair may

tip forward.

• Swing the footrests out of the way, if possible.

PROHIBITED!

3. Never lift this chair by the footrests. Footrests fold or detach

and will not bear the weight of this chair. Lift this chair only

by non-detachable parts of the main frame.

G. MOTOR LOCKS

WARNING

1. Do not engage or disengage motor locks unless power to the

chair is off.

2. Be aware that the chair will not have brakes when motor

locks are in the free-wheel position, unless the chair is

equipped wih optional power base wheel locks.

3. Make sure that the person pushing the chair has full control

when motor locks are disengaged.

H. ON/OFF SWITCH

WARNING

1. Never use the ON/OFF switch to stop the chair except in an

emergency. This will result in an abrupt stop and may cause

you to fall.

2. To slow your chair to a stop, return the joystick to neutral.

I. PNEUMATIC TIRES

WARNING

Proper inflation extends the life of your tires and makes

your chair easier to use.

1. Do not use this chair if any of the tires are under- or over-

inflated. Check weekly for proper inflation level, as listed on

the tire sidewall.

2. Low pressure in a tire may cause the chair to veer to one

side and result in a loss of control.

3.

An over

-inflated tire may burst.

4. Never use a gas station air pump to inflate a tire. Such pumps

provide air at high volume, and could cause the tire to burst.

T

o prevent tire damage:

• Use a hand pump (or a low volume air pump) to inflate

tires.

• Use a tire gauge to check pressure.

5. Driving over sharp objects may cause damage to pneumatic

tires and tubes.

932213 Rev. C

12

ENGLISH

VII.

O. WIRING

WARNING

Never pull on cables directly. This can result in wires

breaking inside the connector or harness. To remove a

plug or connector, always grasp the plug or connector

itself.

P. MANUAL TILT

WARNING

1. Operation

• While driving this wheelchair in the tilted position use cau-

tion.

• Do Not attempt to operate the tilt while positioned on an

incline.

2. Pinch points

Pinch points may occur when operating the tilt on this chair.

Ensure all hands and body parts are clear of all tilt compo

-

nents that may result in pinch points before operating the tilt.

3. Maximum User Weight

Do not exceed the weight capacity for your specific

chair/seating system configuration. Doing so could result in

premature failure or injury.

Q. TRANSIT USE

WARNING

1. If possible and feasible, the rider should transfer to the

Original Equipment Manufacturer vehicle seat and use the

vehicle restraint.

2. If the wheelchair is used for transport, it must be used in a

forward-facing seating position.

3. The rider must not weigh more than 165 lbs.

4. Figure 1 shows the location of the wheelchair securement

points.

5. Use only with Wheelchair Tiedown and Occupant Restraint

Systems (WTORS) that have been installed in accordance

with the manufacturer’s instructions and SAE J2249.

6.

Attach WTORS to securement points in accordance with the

manufacturer’s instructions and SAE J2249.

7. Attach occupant restraints in accordance with the manufac-

turer

’s instructions and SAE J2249.

Q-NOTE– To obtain a copy of SAE J2249 Wheelchair Tiedown and

Occupant Restraint Systems for Use in Motor Vehicles, please con-

tact: SAE International - 400 Commonwealth Drive - Warrendale,

PA 15096 - 412.776.4970

If you fail to heed these warnings damage to your chair

, a fall, tip-

over or loss of control may occur and cause severe injury to the

rider or others.

J. POSITIONING BELTS

WARNING

Use a positioning belt only to help support your pos-

ture. Improper use of such belts may cause severe

injury or death.

1. Make sure you are not at risk to slide down in the wheelchair

seat. If this occurs, you may suffer chest compression or suf-

focate due to pressure from the belt.

2.

A pelvic wedge or a similar device can help you from sliding

down in the seat. Consult your health care professional to

find out if you need such a device.

3. The belt must be snug, but must not be so tight that it inter-

feres with breathing. You should be able to slide your open

hand, flat, between the belt and your stomach.

4. Make sure you can easily remove the belt in an emergency.

5. Never use a positioning belt:

• In place of a motor vehicle seat belt. In an accident or

sudden stop you may be thrown from the chair. A posi-

tioning belt will not prevent this, and further injury may

result from the belt.

• As a restraint. A restraint requires a doctor’s order.

• On a rider who is comatose or agitated.

K. PUSH HANDLES (seat frame only)

WARNING

1. Push handles provide secure points for an attendant to propel

and control the chair. This helps to prevent a fall or tip-over.

2. Check to make sure push handle grips will not rotate or slip off.

L. SEATING SYSTEMS

WARNING

1. Use of a seating system not approved by Sunrise may alter

the center of balance of this chair. This may cause a fall or

tip-over.

2. Never change the seating system of your chair unless you

consult your supplier first.

M. UPHOLSTERY FABRIC

WARNING

1.

Replace worn or torn fabric of the seat as soon as you can. If

you fail to do so, the seat may fail and cause you to fall. Worn

fabrics may increase the potential for a fire hazard.

2. Fabric will deteriorate with age and use. Look for fraying,

thin spots, or stretching of fabric at rivet holes. R

eplace fabric

as required.

3. Be aware that washing may reduce flame retardation of the

fabric.

N. SUSPENSION (Power base only)

WARNING

The suspension system does contain Dry Natural

Rubber. The suspension, or any other component on the

chair

, does not contain any late

x based product. The

suspension components are enclosed and inaccessible to

the user.

932213 Rev. C

13

ENGLISH

VII.

R. TRANSIT OPTION

WARNING

1. Use only Wheelchair Tiedown

and Occupant Restraint

Systems (WTORS) which

meet the requirements of SAE

J2249 Recommended Practice

- Wheelchair Tiedown and

Occupant Restraint Systems

For Use in Motor V

ehicles.

Do not use WTORS designed

to rely on the wheelchair

structure to transfer occupant

restraint loads to the vehicle.

2. The wheelchair has been

dynamically tested in a for-

ward-facing mode for a 48-

km/h frontal impact test. The

wheelchair must be forward-

facing during transport.

3. In order to reduce the potential of injury to vehicle occu-

pants, wheelchair-mounted accessories, such as trays and

respiratory equipment, should be removed and secured sep-

arately.

4. Postural supports and positioning devices should not be

relied on for occupant restraint.

5. Do not alter or substitute wheelchair frame parts, compo-

nents or seating.

6. Sudden stops or impacts can structurally damage your chair.

Chairs involved in such incidents should be replaced.

S. REAR WHEEL LOCKS

WARNING

Rear wheel locks are NOT designed to slow or stop a

moving wheelchair. Use the only to keep the rear wheels

from rolling when your chair is at a complete stop.

1. NEVER use rear wheel locks to try to slow or stop your

chair when it is moving. Doing so may cause you to veer out

of control.

2. To keep the rear wheels from rolling, always set both rear

wheel locks when you transfer to or from your chair.

3. Low pressure in a rear tire may cause the wheel lock on that

side to slip and may allow the wheel to turn when you do

not expect it.

4. Make sure lock arms embed in tires at least 1/8 inch when

locked. If you fail to do so, the locks may not work.

If you fail to heed these warnings damage to your chair

, a fall, tip-

over or loss of control may occur and cause severe injury to the

rider or others.

T. MODIFIED SEAT SYSTEMS

WARNING

Use of a seat system not approved by Sunrise may alter

the center of balance of this chair. This may cause the

chair to tip over.

1. Do not change the seat system of your chair UNLESS you

consult your authorized supplier first.

2. Use of a seat system not approved by Sunrise may affect the

folding mechanism of this chair.

3. Use of a seating system not provided by Sunrise is prohibited

for transit use.

If you fail to heed these warnings damage to your chair, a fall, tip-

over or loss of control may occur and cause severe injury to the

rider or others.

U. ANTI-TIP TUBES (optional) (Manual Carrier)

WARNING

Anti-tip tubes can help keep your chair from tipping over backward

in most normal conditions.

1. Sunrise Recommends Use Of Anti-Tip Tubes:

a. UNLESS you are a skilled rider of this chair and are sure

you are not at risk to tip over.

b. Each time you modify or adjust your chair. The change

may make it easier to tip backward. Use anti-tip tubes

until you adapt to the change, and are sure you are not at

risk to tip over.

2. When locked in place (in the “down” position) anti-tip tubes

should be BETWEEN 1 1/2 to 2 inches off the ground.

a. If set too HIGH, they may not prevent a tip-over.

b. If set too LOW, they may “hang up” on obstacles you can

expect in normal use. If this occurs, you may fall or your

chair may tip over.

3. Keep Anti-Tip Tubes Locked In Place UNLESS:

a. You have an attendant; or

b. You have to climb or descend a curb, or overcome an

obstacle, and can safely do so without them. At these

times, make sure anti-tip tubes are up, out of the way.

Front securement

point

Rear securement point

932213 Rev. C

14

ENGLISH

VIII. SET-UP, ADJUSTMENT & USE

NOTES:

1. Work Surface For Set-Up:

Use a flat surface, such as a table, to assemble, adjust and check your chair. This makes the

steps easier and helps ensure a correct set-up.

2. Fasteners:

•

Many of the screws and bolts on this chair are special high-strength fasteners and may

have special coatings.

• Many nuts are of the Nylock type. They have a plastic insert to help prevent loosening.

WARNING

1. Use of improper fasteners may cause the chair to fail.

2. Over- or under-tightened fasteners may fail or cause damage to chair parts.

3. If bolts or screws become loose, tighten them as soon as you can. Loose bolts

or screws can cause damage to other chair parts causing them to fail.

3. Washers & Spacers:

• Note the position of washers and spacers before disassembly.

• To avoid damage to the frame, replace all washers and spacers when you reassemble

parts.

4. Torque Settings:

• A torque setting is the optimal tightening for a particular fastener. Use a torque wrench

that measures 120 inch-pounds to secure screws, nuts and bolts on this chair.

Q-NOTE– Unless otherwise noted, use a torque setting of 120 inch-pounds for all fasteners.

TOOLS YOU WILL NEED

1. Basic Tool Kit:

To set-up, adjust and maintain your chair you will need the following tools:

•3mm Allen Wrench •13mm Socket Wrench •7/16" box and open-end wrench

•5mm Allen Wrench •16mm Open-end Wrench •1/2" box and open-end wrench

•6mm Allen Wrench •19mm Open-end Wrench •3/4" box and open-end wrench

•8mm Allen Wrench •Flat Head Screwdriver •5/32" Allen wrench

•13mm Open-end Wrench•Phillips screwdriver #2 •Custom axle wrench

•17mm Socket Wrench •Standard Tools

You can obtain a multi-purpose tool kit from Sunrise, or buy the tools you need from a hardware store.

2. Torque Wrench:

If you plan to adjust and maintain this chair yourself, Sunrise recommends that you use a

torque wrench.

Q-NOTE– The wrench must measure inch-pounds. You can buy a torque wrench and proper sockets

from a hardware store.

932213 Rev. C

15

ENGLISH

VIII.

A. BATTERY REMOVAL (Figures 1, 2 & 3)

T

o remove the batteries for transporting or servicing:

1. Remove Batteries

a.

Remove seat following instructions in section “C. Power Base Seat Removal.”

b.

Remove battery access panel by inserting a flat head screw driver between the panel

and main shroud toward the back of the panel at the word “open”.

c. Push the screw driver forward until the panel lifts off.

d. Unplug and remove batteries from rear of chair.

e.

Lift up batteries by lifting up on battery straps.

2. Battery Installation

See Section XI. Batteries, D for installation and wiring diagram.

WARNING

Batteries may weigh up to 55 lbs. Care must be taken to avoid injury when lift-

ing up on battery straps.

B. POWER BASE SEAT HEIGHT ADJUSTMENT

(Figure 4–Mount for power tilt shown)

1. Remove pins (A) from all four seat mount posts.

2. Select the desired seat height (rear seat mount should never be more then one posi-

tion lower then the front).

3. Reinsert the pins.

WARNING

Ensure both front seat posts are positioned to the same height. Rear seat posts

should also be set to the same height.

C. POWER BASE SEAT REMOVAL (Seat Frame)

1. Remove Seat

(Figures 5 & 6)

a. Remove safety lock-out pin (B).

b. Pull the two seat release levers upward

c. Tilt seat backward slightly

d. Pull the forward seat and remove.

e.

When replacing the seat into the mounts, ensure you do not pinch your fingers.

4

A

5

6

B

1

2

3

932213 Rev. C

16

ENGLISH

VIII.

D. POWER BASE SHROUD REMOVAL

The plastic protective shroud can be removed for adjustment or servicing.

1. Remove Colored Shroud

T

wo removable colored shroud covers are Velcro

®

-ed on to the sides of the main shroud. T

o

remove, simply peel the colored shroud off of the main shroud as shown in Figure 7.

2. Remove Main Shroud

a.

Remove both brake releases by unscrewing the front connection and pulling them out.

(Figure 8)

b. Lift the middle shroud assembly off.

3.

Replace Main Shroud

Replace shroud by reversing above instructions.

E. CHECK-OUT

Once the wheelchair is assembled and adjusted, it should roll smoothly and easily. All acces-

sories should also perform smoothly.

After the wheelchair has been set up be sure the chair performs to your specified operational

settings (see Operating Guide). If the chair does not perform to specifications, turn the wheel-

chair OFF immediately and reprogram operational specifications using the Quickie Hand Held

Programmer.

Repeat this procedure until the wheelchair performs to specifications before

attempting active use of the wheelchair.

If you have any problems, follow these procedures:

1. Review the Set-up, Adjustment & Use section and Operating Guide to make sure chair

was properly prepared.

2. If your problem persists, contact your authorized supplier. If you still have a problem

after contacting your authorized supplier, contact Sunrise customer service. See the

introduction page for details on how to contact your authorized supplier or Sunrise

customer service.

WARNING

When properly set up, this chair will operate smoothly. Check to see that all

components work properly. If you detect a problem, be sure to correct it

before use.

7

8

932213 Rev. C

17

ENGLISH

VIII.

F. BACKREST

1. To Secure The Backrest For Operation:

a) Lift backrest to upright position.

b)

When secured, backrest pin will lock into place.

Q-NOTE– Zippie series wheelchairs are shipped with the backrest in a folded position.

G. SWING-AWAY HANGERS (60º, 70º, or 90º)

(Fig. 9)

1. Attaching/Removal

a) Place swing-away pivot saddle (A) into the receiver on front frame tube with the

footrest facing outward from the frame.

b) Rotate the footrest inward until it locks into place on locking bolt.

c) To remove hanger, push release latch (B) toward the frame, rotate footrest outward,

and lift.

H. ARTICULATING LEGREST (Optional)

(Fig. 10)

1. Attaching/Removal

a) Place swing-away pivot saddle (A) into the receiver on front frame tube with the

footrest facing outward from the frame.

b) Rotate the footrest inward until it locks into place on locking bolt.

c) To remove hanger, push release latch (B) toward the frame, rotate footrest outward,

and lift.

2. Elevating

a) To raise legrest, lift to desired position. Legrest will automatically lock in place.

b) To lower legrest, while seated in chair hold lever (C) down, lower legrest to desired

position, then release lever. Legrest will automatically lock in place.

I. ELEVATING AND 90º ELEVATING LEGRESTS (Optional)

(Fig. 11)

1. Attaching/Removal

a) Place swing-away pivot saddle (A) into the receiver on front frame tube with the

footrest facing outward from the frame.

b)

R

otate the footrest inward until it locks into place on locking bolt.

c) To remove hanger, push release latch (B) toward the frame, rotate footrest outward,

and lift.

2. Elevating

a) To raise legrest, lift to desired position. Legrest will automatically lock in place.

b) To lower legrest, while seated in chair hold lever (C) down, lower legrest to desired

position, then release lever

. Legrest will automatically lock in place.

Articulating Legrest

Swing-Away Hanger

90º Elevating Legrest

B

A

C

B

A

9

B

A

C

10

11

932213 Rev. C

18

ENGLISH

VIII.

J. COMPOSITE FOOTPLATE (Fig. 12)

1. Height Adjustment

a) Remove retaining bolts in the frame tube (A).

b)

Slide footplate and extension tubes to desired height.

c) Left and right footrest will normally be at equal height.

d) Replace and tighten bolts.

K. KIDS & ADULT ANGLE ADJUSTABLE FOOTPLATE

(Figs. 13 & 14)

1. Height Adjustment (Fig. 13)

a)

Remove the retaining bolt from the frame tube (A).

b) Move footplate assembly to desired height.

c) Left and right footrest will normally be at equal height.

d) Replace and tighten bolt.

2. Angle Adjustment (Fig. 14)

a) Loosen fasteners (B) until the adjustable clamp and footplate rotate freely on the

mounting tube.

b) Adjust the angle of the footplate.

c) Tighten nuts.

3. Position Adjustment (Fig. 14)

a) Remove footplate fasteners (B).

b) Move footplate to the desired location.

c) Replace and tighten fasteners.

L. ALUMINUM FOOTPLATE (Fig. 15)

1. Height Adjustment

a) Remove set screws (A) from frame tube.

b) Slide footplate to desired height.

c) The adjustment on each side of the footrest will normally be of equal height.

d) Replace and tighten set screws.

M. 90º FOOTBOARD (Fig. 16)

1. Height Adjustment

a) Loosen the nuts on the footplate clamp assembly (A).

b) Slide footplate clamps to desired height.

c)

Tighten nuts.

2. Angle Adjustment

a) Loosen nuts under the footplate assembly (B) until the adjustable clamp rotates freely

on the supporting tube.

b) Adjust the angle of the footplate.

c)

Slide it forward or back for

correct placement.

d) Tighten nuts.

3. Removing Footboard

a)

Unscrew the lock knobs (C) and lift out of clamp assembly.

Composite Footplate

A

Angle Adjustable

Footplate

A

Footplate Angle &

Position Adjustment

B

Aluminum Footplate

A

90º Footboard

A

B

C

12

13

14

15

16

932213 Rev. C

19

ENGLISH

VIII.

N. PLATFORM FLIP-UP FOOTPLATE (Fig. 17)

1. Height Adjustment

a) Remove retaining bolts in the frame tube (A).

b)

Slide footplate and extension tubes to desired height.

c) The adjustment on each side of the footrest should be of equal height.

d) Replace and tighten bolts.

2.

Angle Adjustment

a) Loosen the nuts under the footplate clamp (B) until the adjustable clamp and footplate

rotate freely on the mounting tube.

b) Adjust the angle of the footplate.

c) Tighten nuts.

O. HEIGHT-ADJUSTABLE ARMRESTS (Optional) (Fig. 18)

1. Installation

a) Slide the outer armpost into the receiver mounted to the wheelchair frame.

b) The armrest should lock in place automatically.

2. Removing Armrest

a) Press release lever (A) and remove the armrest.

Q-NOTE– Release lever should move freely. Do not force or over rotate.

3. Height Adjustment

a) Rotate release lever (A) to second stop.

Q-NOTE– Release lever should move freely. Do not force.

b) Slide armrest pad up or down.

c) Return lever to locked position against armpost.

d) Push arm pad until upper armpost locks firmly into place.

e) A snap lock is engaged if the armrest is raised to its highest adjustment. To disconnect

the snap lock, press in on the button head and press the armrest down.

4. Replacing Armrest

a) Slide armrest back into receiver until it stops.

Q-NOTE– Check to make sure release lever is engaged by pulling up on armrest.

5. Adjusting Armrest Receiver Fit

To tighten or loosen the fit of the outer armpost in the receiver:

a) Loosen the four bolts on the side of the receiver.

b)

With the armrest in the receiver

, squeeze the receiver to achieve the desired fit.

c) Tighten the four bolts.

6. Adjusting Inner Armpost Fit

a) Two set screws (C) are installed in the outer armpost.

b) Turn the set screws in or out until the desired fit is achieved.

P. JOYSTICK & ENHANCED DISPLAY (Figs 19, 20, 21, 22)

1. To Connect (Fig. 21)

a. Line up the groove on the joystick cable (A) with the groove on the wing of the wheel-

chair cable (B).

b. Push the connectors together and then turn the wing of the wheelchair cable until the

two wings line up (C).

2. To Disconnect (Fig. 22)

a. Turn the wing (D) so that both the groove on the wing of the wheelchair cable and the

groove on the joystick cable line up.

b.

Pull apart the two connectors.

Platform Flip-up

Footplate

B

A

Height Adjustable

Armrest

A

B

C

AB

C

D

Enhanced Display

Qr3 Remote Joystick

17

18

19

20

21

22

932213 Rev. C

20

ENGLISH

VIII.

Q. TO ADJUST THE HEIGHT OF THE JOYSTICK

OR ENHANCED DISPLAY (Fig. 23)

1.

Loosen the two Socket Head screws (E).

2. Slide the clamp (F) up or down until in desired position.

3. Retighten the two Socket Head Screws (E).

R. JOYSTICK OR ENHANCED DISPLAY SWING-AWAY

RETRACTABLE MOUNT

(Optional) (Fig. 24)

The joystick or Enhanced Display is mounted with a mechanism which allows the control to

be locked in a forward or retracted position using magnets.

Adjustment

a. To retract the joystick or Enhanced Display, push outward on the inside of joystick.

b. Push the joystick or Enhanced Display away from front of armrest until it locks into

retracted position.

c. To return to forward position, push the joystick or Enhanced Display forward until it

locks into place.

S. WHEEL LOCKS

Zippie wheelchairs are shipped with wheel locks. Wheel locks are installed at Sunrise unless

you have requested otherwise.

Use a torque setting of 100 in./lbs when setting-up wheel locks.

1. Wheel Lock

a. Loosen the screws on the top of each clamp. Do not attempt to remove one screw at

a time.

b. Slide assembly toward drive wheel until clamp embeds into tire to prevent wheel

movement when in locked position.

c. Adjust angle position.

d. Tighten screws.

T. ANTI-TIP TUBES - REAR (Manual carrier) (Fig. 25)

1. To Insert Anti-Tip Tubes into Receivers

a) Press the anti-tip release button on the anti-tip tube so that the release pin is drawn

inside.

b) Insert the tube into the anti-tip receiver.

c) Turn the anti-tip tube until release pin is positively engaged in the receiver mounting

hole.

d) Insert second anti-tip tube the same way.

2.

To Adjust Anti-Tip Height

a)

P

ress the anti-tip wheel release button (A) so the release pin is drawn inside.

b) Raise or lower to one of the three pre-drilled holes.

c) Turn the anti-tip tube until release pin is positively engaged in the receiving hole (B).

d)

Adjust the second anti-tip tube wheel the same way

. Both wheels should be exactly the

same height.

U. SEAT REMOVAL (Figs. 26 & 27)

1. Disconnect joystick.

2. Pull out the safety pin from the left front seat post (Fig. 26).

3.

Lift up on both front seat latches (Fig. 27).

4. Tilt the seat back, slide it forward, and remove from the base.

Anti-Tip Height

A

B

EF

23

24

25

26

27

Page is loading ...

Sunrise Medical Zippie Z-Bop User manual

This manual is also suitable for

Sunrise Medical Zippie Z-Bop User manual

in other languages

Related papers

Other documents