PN-86HC1 Dismantle Instruction
1
Dismantle Instruction
LCD MONITOR
MODEL
PN-86HC1
PN-86HC1 Dismantle Instruction
2
Table of contents
1. Scope ............................................................................................................... 3
2. Tools for dismantling............................................................................................. 3
3. Dismantle Procedure ............................................................................................ 3
4. Back covers ........................................................................................................ 4
5. Printed circuit boards ........................................................................................... 5
6. Batteries ........................................................................................................... 6
7. LCD Module/cover glass/bracket .............................................................................. 7
8. Capacitors .......................................................................................................... 8
9. Parts List ........................................................................................................... 8
PN-86HC1 Dismantle Instruction
3
1. Scope
This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU.
2. Tools for dismantling
Below tools are required to dismantle this product.
- Screw Driver
- Nipper
3. Dismantle Procedure
This product can be dismantled by below steps.
1. Remove Back covers (section 4)
2. Remove the shielding
3. Remove Printed circuit boards (section 5)
4. Remove battery (section 6)
5. Dismantle LCD (section 7)
6. Remove Electrolyte Capacitors (section 8)
PN-86HC1 Dismantle Instruction
4
4. Back cover
Back cover can be removed by screw driver.
PN-86HC1 Dismantle Instruction
5
5. Printed circuit boards
All PWBs can be removed by screw driver.
Main PWB (1pcs) T-con PWB(1pcs)
Power PWB (1pcs) OPS PWB(1pcs)
Power adapter for OPS (1pcs)
PN-86HC1 Dismantle Instruction
6
6. Batteries
This model uses CR2032 Lithium Coin battery on MAIN PWB.
Battery CR2032 can easily be removed from the battery holder.
This model uses AAA battery for remote control.
Battery can easily be removed.
PN-86HC1 Dismantle Instruction
7
7. LCD Module bezels/bracket
- LCD Dismantle procedure
1. Remove screws
2. Remove Cover glass and Bezels
3. Remove screws
4. Remove Middle Frame
5. After you have removed the PWB´s, the cover glass and bezels please take out the cables from
the LCD module.
LCD
PN-86HC1 Dismantle Instruction
8
8. Capacitors
Electrolyte Capacitors which diameter/height is larger than 25mm is installed on the Power PWB.
These capacitors can be removed by using nipper to cut the leads.
9. Parts List
Parts described in Annex VII of directive 2012/19/EU are as below.
Parts
Note
LCD
86inch LCD module
Batteries
Battery CR2032 of the main board
Battery (AAA) of remote control
Printed Circuit Boards
Main PWB
T-CON PWB
Power PWB
OPS PWB
Electrolyte capacitors
(height >25mm, diameter >25mm)
On the Power PWB
External electric cables
2 kinds of Power Cord
- CEE 7 (for EU)
- Type-BF (for UK)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Sharp PN-65HC1 Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sharp PN-HW501T Owner's manual
-
-
Sharp PN -L752B Operating instructions
-
Sharp PN-L652B User manual
-
Sharp PNR606 Owner's manual
-
Sharp PN-R706 Owner's manual
-
Sharp PNV701A Owner's manual
-
Sharp PN-CD701 Owner's manual
-
Sharp PN-HW861 Owner's manual
-
Sharp PN70HC1E Owner's manual
Other documents
-
LG 43LQ60006LA Operating instructions
-
LG 43UQ76903LE User manual
-
LG Electronics QNED85 Series User manual
-
LG 65UR73003LA Operating instructions
-
LG Electronics UR75 Series User manual
-
LG NANO76 Series User guide
-
Sony PCGC1MW User manual
-
Hitachi CP-S210W User manual
-
Ericsson Orion Service Section
-