SENSIT Technologies Gas Trac LZ-30 Quick Start Instructions

Brand
SENSIT Technologies
Model
Gas Trac LZ-30
Type
Quick Start Instructions

SENSIT Technologies Gas Trac LZ-30 is a portable gas leak detector designed to help you quickly and easily find gas leaks. It features an IR laser tuned for methane detection, a green spotter laser to indicate the location of the IR laser, and a red distance laser to measure the distance to the target. The LZ-30 also has three preset alarm levels (20%, 50%, and 100%) to alert you to the presence of a gas leak.

The LZ-30 is easy to use. Simply press and hold the ON/MENU button to turn it on. Remove the instrument from the case and point it at the area you want to test. Press and release the MEASURE button to start the measurement. Slowly scan the area in an "S" or "Z" pattern to maximize coverage. The LZ-30 will display the maximum ppm-m result in the lower left corner of the display.

SENSIT Technologies Gas Trac LZ-30 is a portable gas leak detector designed to help you quickly and easily find gas leaks. It features an IR laser tuned for methane detection, a green spotter laser to indicate the location of the IR laser, and a red distance laser to measure the distance to the target. The LZ-30 also has three preset alarm levels (20%, 50%, and 100%) to alert you to the presence of a gas leak.

The LZ-30 is easy to use. Simply press and hold the ON/MENU button to turn it on. Remove the instrument from the case and point it at the area you want to test. Press and release the MEASURE button to start the measurement. Slowly scan the area in an "S" or "Z" pattern to maximize coverage. The LZ-30 will display the maximum ppm-m result in the lower left corner of the display.

Quick-Start Instructions
This is not a substitute for the
instruction manual. It is for
reference only.
Read and understand the
instruction manual before use.
Distributed by:
851 Transport Drive
Valparaiso, IN 46383-8432
Phone: 219 465 2700
Web: www.gasleaksensors.com
Innovative Detection Solutions
1. With the instrument in the carry case,
press and hold the ON/MENU button
until the screen illuminates (instrument
may require charge before use).
2. Make sure the path between the
calibration cell and instrument is
unobstructed and both the cell and
instrument are fully seated in the case.
3. A “bump test” can be performed by
pressing and releasing the MEASURE
button. Wait for 5 seconds and press
and release the MEASURE again to
deactivate. A MAX ppm-m result (located
lower left on display) should display 1500
ppm-m (3.0%LEL / 0.15%V/V) or higher.
If the result is less than 1500 ppm-m
(3.0%LEL / 0.15%V/V), attempt the bump
test again. If still unsuccessful, refer to the
owners manual for calibration instructions.
4. Remove the instrument from the case. Point
the instrument at an area of concern, press
and release the MEASURE button. Using
the “green” spotter laser, slowly scan the
area in an “S” or “Z” pattern to maximize
coverage. NOTE: The laser needs
sufcient reection off of an object for
proper operation. If not achieved, REF/L
(reection low) or REF/H (reection high)
may be shown. Reposition or approach
from a different angle and try again.
5. For detection through widows, avoid
90 degree detection and maintain
distances greater than 5 meters.
6. When your investigation is complete,
stop the measurement by pressing
and releasing the MEASURE button.
7. To power the instrument off, press and
hold the OFF/BACK button until display
goes completely dark.
LZ-30
Quick Start
WARNING:
AVOID EYE CONTACT WITH LASER.
Alarm - (preset and adjustable, visual/
audible/vibration) Three levels 20%, 50% and
100% of alarm set point.
PLEASE REFER TO OWNERS MANUAL
FOR COMPLETE DETAILS ON THE
AFOREMENTIONED AND MORE!
Laser (color and function)
IR Laser = laser that is tuned for methane
detection, not in the visible spectrum.
Green = Spotter laser, represents location
of IR laser
Red = Distance laser, represents the
distance in meters at which the IR laser is
traveling.
  • Page 1 1
  • Page 2 2

SENSIT Technologies Gas Trac LZ-30 Quick Start Instructions

Brand
SENSIT Technologies
Model
Gas Trac LZ-30
Type
Quick Start Instructions

SENSIT Technologies Gas Trac LZ-30 is a portable gas leak detector designed to help you quickly and easily find gas leaks. It features an IR laser tuned for methane detection, a green spotter laser to indicate the location of the IR laser, and a red distance laser to measure the distance to the target. The LZ-30 also has three preset alarm levels (20%, 50%, and 100%) to alert you to the presence of a gas leak.

The LZ-30 is easy to use. Simply press and hold the ON/MENU button to turn it on. Remove the instrument from the case and point it at the area you want to test. Press and release the MEASURE button to start the measurement. Slowly scan the area in an "S" or "Z" pattern to maximize coverage. The LZ-30 will display the maximum ppm-m result in the lower left corner of the display.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents