GE DCVH680GJMV User manual

Safety Instructions . . . . . . . . 2–5

Operating Instructions

Control Panels . . . . . . . . . . . . . . . . . 6–9

Cycle Options . . . . . . . . . . . . . . . .10, 11

Dryer Features . . . . . . . . . . . . . . . . . .11

Reversing the Door Swing . . . .12–16

Loading and Using

the Dryer . . . . . . . . . . . . . . . . . . . . .17, 18

Venting the Dryer . . . . . . . . . . . . . . .19

Stacking . . . . . . . . . . . . . . . . . . . . .20–23

Troubleshooting Tips . . . .24–26

Consumer Support

Warranty . . . . . . . . . . . . . . . . . . . . . . . 27

Consumer Support . . . . . . . . . . . . . . 28

GEAppliances.com

Dryers

364B7130P001 49-90393-3 08/11 GE

DBVH520

DCVH640

DCVH680

DHDVH68

GFDN100

GFDN110

Owner’s Manual

Write the model and serial

numbers here:

Model # ______________

Serial # ______________

They are on the label on

the front of the dryer behind

the door.

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

California Safe Drinking Water and Toxic Enforcement Act

This act requires the governor of California to publish a list of substances known to the state to cause cancer,

birth defects or other reproductive harm and requires businesses to warn customers of potential exposure

to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized

further by properly venting the dryer to the outdoors.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk

of fire or explosion, electric shock, or to prevent property damage, personal injury, or

death.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light a match, or cigarette,

or turn on any gas or electrical

appliance.

Do not touch any electrical switch;

do not use any phone in your building.

Clear the room, building or area of all

occupants.

Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions carefully.

If you cannot reach your gas supplier,

call the fire department.

5

4

3

2

1

 Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

 Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

 Properly ground dryer to conform with all governing

codes and ordinances. Follow details

in Installation Instructions.

 Install or store where it will not be exposed

to temperatures below freezing or exposed

to the weather.

 Connect to a properly rated, protected and sized

power supply circuit to avoid electrical overload.

 Remove the colored protective film from both

the control panel and the door.

 Remove all sharp packing items and dispose

of all shipping materials properly.

 Do not remove the vent protector from the back

of the dryer (on some models).

 Pull the protector out and down to its lowest

position and connect the exhaust duct to the dryer.

The lowered protector will prevent the duct from

getting crushed (on some models).

Exhaust/Ducting:

Dryers MUST be exhausted to the outside to

prevent large amounts of moisture and lint from

being blown into the room.

Use only rigid metal or flexible metal 4” diameter

ductwork inside the dryer cabinet or for

exhausting to the outside. USE OF PLASTIC OR

OTHER COMBUSTIBLE DUCTWORK CAN CAUSE

A FIRE. PUNCTURED DUCTWORK CAN CAUSE A

FIRE IF IT COLLAPSES OR BECOMES OTHERWISE

RESTRICTED IN USE OR DURING INSTALLATION.

For complete details, follow the Installation

Instructions.

2

1

3

PROPER INSTALLATION

This dryer must be properly installed and located in accordance with the Installation Instructions

before it is used. If you did not receive an Installation Instructions sheet, you can receive one by

visiting GEAppliances.com, or by calling 800.GE.CARES (800.432.2737).

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

GEAppliances.com

4

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

YOUR LAUNDRY AREA

 Keep the area underneath and around your

appliances free of combustible materials

(lint, paper, rags, etc.), gasoline, chemicals

and other flammable vapors and liquids.

 Keep the floor around your appliances clean

and dry to reduce the possibility of slipping.

 Close supervision is necessary if this appliance

is used by or near children. Do not allow children to

play on, with or inside this or any other appliance.

 Keep all laundry aids (such as detergents,

bleaches, etc.) out of the reach of children,

preferably in a locked cabinet. Observe all warnings

on container labels to avoid injury.

 Never climb on or stand on the dryer top.

WHEN USING YOUR DRYER

 Never reach into the dryer while the drum is

moving. Before loading, unloading or adding

clothes, wait until the drum has completely

stopped.

 Clean the lint filter before each load to prevent lint

accumulation inside the dryer or in the room.

DO NOT OPERATE THE DRYER WITHOUT

THE LINT FILTER IN PLACE.

 Do not wash or dry articles that have been

cleaned in, washed in, soaked in or spotted

with combustible or explosive substances

(such as wax, oil, paint, gasoline, degreasers,

dry-cleaning solvents, kerosene, etc.) which may

ignite or explode. Do not add these substances

to the wash water. Do not use or place these

substances around your washer or dryer during

operation.

 Do not place items exposed to cooking oils in your

dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause

a clothes load to catch fire

.

 Any article on which you have used a cleaning

solvent or that contains flammable materials

(such as cleaning cloths, mops, towels used in

beauty salons, restaurants or barber shops, etc.)

must not be placed in or near the dryer until

solvents or flammable materials have been

removed. There are many highly flammable items

used in homes such as acetone, denatured alcohol,

gasoline, kerosene, some household cleaners,

some spot removers, turpentines, waxes, wax

removers and products containing petroleum

distillates.

 The laundry process can reduce the flame

retardancy of fabrics. To avoid such a result,

carefully follow the garment manufacturer’s

care instructions.

 Do not dry articles containing rubber, plastic, foam

or similar materials such as padded bras, tennis

shoes, galoshes, bath mats, rugs, bibs, baby pants,

plastic bags, pillows, etc., that may melt or burn.

Some rubber materials, when heated, can under

certain circumstances produce fire by spontaneous

combustion.

 Do not store plastic, paper or clothing that may

burn or melt on top of the dryer during operation.

 Garments labeled Dry Away from Heat or Do Not

Tumble Dry (such as life jackets containing kapok)

must not be put in your dryer.

 Do not dry fiberglass articles in your dryer.

Skin irritation could result from the remaining

particles that may be picked up by clothing

during subsequent dryer uses.

 To minimize the possibility of electric shock, unplug

this appliance from the power supply or disconnect

the dryer at the building’s distribution panel by

removing the fuse or switching off the circuit

breaker before attempting any maintenance or

cleaning (except the removal and cleaning of the

lint filter). NOTE: Pressing START, STOP or POWER

does NOT disconnect the appliance from the power

supply.

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

WHEN NOT USING YOUR DRYER

 Grasp the plug firmly when disconnecting this

appliance to avoid damage to the cord while

pulling. Place the cord away from traffic areas

so it will not be stepped on, tripped over or

subjected to damage.



Do not attempt to repair or replace any part

of this appliance or attempt any servicing unless

specifically recommended in this Owner’s Manual

or in published user-repair instructions that you

understand and have the skills to carry out.

 Before discarding a dryer, or removing it from

service, remove the dryer door to prevent children

from hiding inside.

 Do not tamper with controls.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

5

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

GEAppliances.com

WHEN USING YOUR DRYER (cont.)

 Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a

damaged cord or plug.

 The interior of the machine and the exhaust

duct connection inside the dryer should be cleaned

at least once a year by a qualified technician.

See the Loading and Using the Dryer section.

 If yours is a gas dryer, it is equipped with an

automatic electric ignition and does not have

a pilot light. DO NOT ATTEMPT TO LIGHT WITH A

MATCH. Burns may result from having your hand

in the vicinity of the burner when the automatic

ignition turns on.

 You may wish to soften your laundered fabrics

or reduce the static electricity in them by using

a dryer-applied fabric softener or an anti-static

conditioner. We recommend you use either

a fabric softener in the wash cycle, according

to the manufacturer’s instructions for those

products, or try a dryer-added product for which

the manufacturer gives written assurance on

the package that their product can be safely

used in your dryer. Service or performance

problems caused by use of these products

are the responsibility of the manufacturers

of those products and are not covered under

the warranty to this appliance.

About the dryer control panel.

You can locate your model number at the top inside of the door opening.

Model DBVH520

1

5

3

4

6

2

Model DCVH680

Model DCVH640

7

1

5

3

4

6

2

7

1

5

3

4

6

2

7

Model DHDVH68

1

5

3

4

6

2

7

6

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

7

Model GFDN100 / GFDN110

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

8

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

1

2

GEAppliances.com

Power

Press to “wake up” the display. If the display is active, press to put the dryer in the standby mode.

NOTE: Pressing POWER does not disconnect the appliance from the power supply.

Dry Cycles

The dry cycle controls the length and tumble speed of the drying process. The chart below will help you

match the dry setting with the loads.

Sensor Cycles

COTTONS For cottons and most linens.

MIXED LOAD For loads consisting of cottons and poly-blends.

EASY CARE For wrinkle-free and permanent press items.

(on some models)

ACTIVE WEAR Clothing worn for active sports exercise and some casual wear. Fabrics include new

(on some models) technology finishes and stretch fibers such as Spandex.

DELICATES For lingerie and special-care fabrics.

DRYEL

™

Designed for use with the DRYEL

™

“dry clean only” fabric care system. See product

package for directions. For questions or issues related to use and performance of DRYEL

™

,

see the Website at: www.dryel.com.

SPEED DRY For small loads that are needed in a hurry, such as sports or school uniforms.

Can also be used if the previous cycle left some items damp, such as collars or waistbands.

Timed Dry Cycles

DEWRINKLE For removing wrinkles from items that are dry or slightly damp. This cycle is not

(on some models) recommended for delicate fabrics.

WARM UP Provides 10 minutes of warming time to warm up clothes.

AIR FLUFF Use this feature to tumble items without heat.

My Cycle (on some models)

MY CYCLE Press to use, create or modify custom dry cycles.

Timed Dry

Use to set your own dry time. TIMED DRY is also recommended for small loads.

To use TIMED DRY:

1. Turn dry cycle dial to TIMED DRY.

2. Select the drying time by pressing the + and – buttons.

3. Select the DRY TEMP.

4. Close the door.

5. Press START.

Sensor Dry Level

The sensor continuously monitors the amount of moisture in the load. When the moisture in your

clothes reaches your selected dry level, the dryer will stop.

MORE DRY Use for heavy or mixed type of fabrics.

DRY Use for normal dryness level suitable for most loads. This is the preferred cycle

for energy saving.

LESS DRY Use for lighter fabric (ideal for ironing).

DAMP For leaving items partially damp.

(on some models)

3

4

9

About the dryer control panel.

Dry Temp

You can change the temperature of your dry cycle.

ANTI-BACTERIAL This option may only be used with COTTONS or MIXED LOAD cycles. This option reduces

(on some models) certain types of bacteria by 99.9%, including: Staphylococcus aureus, Pseudomonas

aeruginosa and Klebsiella pneumoniae*. The anti-bacterial process occurs when high

heat is used during a portion of this drying cycle.

NOTE: Do not use this cycle on delicate fabrics.

* The Anti-Bacterial Cycle is Certified by NSF International (formerly National Sanitation

Foundation) to NSF Protocol P154 Sanitization Performance of Residential Clothes Dryers.

HIGH For regular to heavy cottons.

MEDIUM For synthetics, blends and items labeled permanent press.

LOW For delicates, synthetics and items labeled Tumble Dry Low.

EXTRA LOW For lingerie and special-care fabrics.

NO HEAT Can only be used with TIMED DRY.

(on some models)

START

Press to start a dry cycle. If the dryer is running, press it once and it will pause the dryer.

Press it again to restart the dry cycle.

My Cycle (on some models)

Set up your favorite combination of settings and save them here for one touch recall.

These custom settings can be set while a cycle is in progress.

To store a MY CYCLE combination of settings:

1. Select your drying cycle.

2. Change DRY TEMP and SENSOR DRY LEVEL settings to fit your needs.

3. Select any drying OPTIONS you want.

4. Press and hold the pad for three seconds to store your selection. A beep will sound

and the pad will light up.

To recall your stored MY CYCLE combination:

Press the MY CYCLE button before drying a load.

To change your stored MY CYCLE combination:

Follow steps 1–4 in “To store a MY CYCLE combination of settings”.

“CLEAN LINT FILTER” (message)

(This message represents only a reminder.)

After the POWER button is pressed, the “CLEAN LINT FILTER” message could appear if the previous

cycle was not finished.

This message will disappear after the START button is pressed. Even though you have already cleaned

the filter (before or after the POWER button has been pressed), the “CLEAN LINT FILTER” message will

still be displayed until the START button is activated.

MY CYCLE

5

6

7

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

About cycle options.

NOTE: Not all features are available on all dryer models. GEAppliances.com

Extend Tumble

Minimizes wrinkles by adding approximately

60 minutes of no-heat tumbling after clothes

are dry. The beeper will sound every

2 minutes to remind you to remove

the clothes. The ESTIMATED TIME REMAINING

display will show 00.

Damp Alert (on some models)

This option causes the dryer to beep when

clothes have dried to a damp level. Remove

items that you wish to hang dry. The DAMP

ALERT will only beep when this option is

selected.

Removing clothes and hanging them when

they are damp can reduce the need to iron

some items.

Signal

Alerts you that the cycle is complete.

The beeper will continue to sound every

two minutes for the next 6 minutes, until

the clothes have been removed. The clothes

should be removed when the beeper goes

off so wrinkles don’t set in.

Press SIGNAL to select low, medium or high

volume, or to turn the beeper off.

Delay Start (on some models)

Use to delay the start of your dryer.

1. Choose your dry cycle and any options.

2. Press DELAY START. You can change

the delay time in 1 hour increments using

the + or – arrow pads.

3. Press the START pad to start

the countdown.

The countdown time will be shown in

the ESTIMATED TIME REMAINING display.

NOTES:

 If the door is opened while the dryer is

in DELAY, the countdown time will not

restart unless the door is closed and

START has been pressed again.

 You can delay the start of a dry cycle

up to 18 hours for models DCVH640,

DCVH680, DHDVH68 and up to 10 hours

for model DBVH520.

DAMP

ALERT

E

XTEND

T

UMBLE

10

11

About cycle options. NOTE: Not all features are available on all dryer models.

Lock

You can lock the controls to prevent any

selections from being made. Or you can lock

the controls after you have started a cycle.

Children cannot accidentally start the dryer

by touching pads with this option selected.

To lock the dryer, press and hold the lock icon

for 3 seconds. To unlock the dryer, press and

hold the lock icon for 3 seconds.

The icon of the lock next to the timer will light

up when the controls are locked.

H

OLD

3 S

EC

TO

S

TORE

M

Y

C

YCLE

My Cycle (on some models)

To save a favorite cycle, set the desired

settings and hold down the MY CYCLE button

for 3 seconds. A beep will sound to indicate

the cycle has been saved.

To use your custom cycle, press

the MY CYCLE button before drying a load.

To change the saved cycle, set the desired

settings and hold down the MY CYCLE button

for 3 seconds.

See page 8 for more details.

DELAY CLEAN LINT FILTER

DRYIN DA C L D N

Estimated Time Remaining

Displays the approximate time remaining

until the end of the cycle.

As the cycle begins, you will see an initial

approximate total cycle time in the display.

Then lights will “race” in the display. This

means the dryer is continuously monitoring

the amount of moisture in the load.

The lights will continue until the dryer senses

a low level of moisture in the load. At that

point, the dryer will calculate and display

the approximate time remaining.

About dryer features.

Drying Rack (on some models)

A handy drying rack may be used for drying delicate items such as washable

sweaters. Place items flat on the drying rack and block such items as wool

sweaters and delicate fabrics. Dry with low heat.

To install the drying rack, pull up the lint filter slightly. Insert the drying rack

into the slots, then push the filter back down.

NOTE:

 The drying rack must be used with the TIMED DRY or RACK DRY

(on some models) cycles.

 Do not use this drying rack when there are other clothes in the dryer.

Drum Lamp

Before replacing the light bulb, be sure to unplug the dryer power cord

or disconnect the dryer at the household distribution panel by removing

the fuse or switching off the circuit breaker. Reach above dryer

opening

from inside the drum. Remove the

bulb and replace with the same size bulb.

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

12

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Reversing the door swing. GEAppliances.com

IMPORTANT NOTES:

 Read the instructions all the way

through before starting.

 Handle parts carefully to avoid

scratching paint.

 Set screws down by their related parts

to avoid using them in the wrong places.

 Provide a non-scratching work surface

for the doors.

 Normal completion time to reverse

the door swing is 30–60 minutes.

IMPORTANT: Once you begin, do not move

the cabinet until door-swing reversal is

completed.

These instructions are for changing

the hinges from the right side to the left

side—if you ever want to switch them

back to the right side, follow these same

instructions and reverse all references

to the left and right.

TOOLS YOU WILL NEED

Adjustable Crescent Wrench

Phillips Head Screwdriver

Putty Knife or

Thin-Blade

Screwdriver

DOOR PARTS

Hinge Assembly

Hinge

Cover

Nut (#8) – 2

Large Tapping

Screw (#10) – 6

Tapping Screw (#8) – 2

Machine Screw (#8) – 6

Washer – 2

Plastic Cover

STEP-BY-STEP INSTRUCTIONS

Before You Start

1. Unplug the dryer from its electrical

outlet.

13

Reversing the door swing.

STEP-BY-STEP INSTRUCTIONS (cont.)

Remove Door Assembly

2. Open the door to approximately 90 degrees. Remove the 4 screws starting

from the bottom to the top. Make sure the door is supported while removing

the screws.

3. Loosen the top screw as shown. Unhook the door by lifting and pulling as

shown by the arrows.

4. Lay the door down on a soft protected flat surface so that the inner part faces

upward (door resting on the handle side).

5. Remove the 6 large tapping screws (#10) located around the perimeter

of the door outlining the gasket, and the 2 machine screws (#8) on the hinge

side.

6. With the screws removed, turn the door over and separate the silver cover part

of the door from the door frame and set aside.

7. Unlock the 4 tabs on the plastic cover and separate the plastic cover from

the frame.

NOTE: Disregard the “DO NOT REMOVE” label on the plastic cover.

6 #10

Large

Screws

2 #8

Machine

Screws

2 #8 Machine Screws

Remove the

four screws

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

14

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

GEAppliances.com

STEP-BY-STEP INSTRUCTIONS (cont.)

Remove Hinge

IMPORTANT: Note the location of the hinge (left or right) before removing.

8.With the door frame part of the door laid down on a protected soft surface,

remove the hinge cover by removing the 2 tapping screws (#8) that fasten

it to the frame. The hinge cover is located at the opposite side of the hinge

assembly.

9.Remove the 2 nuts, washers and the 2 machine screws (#8).

10.Remove the hinge assembly by removing the 2 machine screws (#8) that

fasten it to the frame. Pull the hinge assembly out and set it aside.

Reinstall Hinge Assembly

11. Place the hinge assembly in the opposite side of the door. Align the hinge

holes with the door holes.

12. Loosely fasten the hinge assembly to the edge using 2 machine screws (#8).

13. Hold the door on its side with one hand and fasten the remaining 2 screws as

shown. Then tighten the 2 screws (#8) holding the hinge assembly.

STEP-BY-STEP INSTRUCTIONS (cont.)

Reinstall Nuts and Hinge Cover

14. Place the door on its edge. Assemble the 2 machine screws (#8), washers

and nuts. Tighten using a wrench and screwdriver.

15. Place the hinge cover in position. Align the hinge cover holes with the holes

in the door.

16. Secure the hinge cover with the 2 tapping screws (#8).

Reassemble Door Assembly

IMPORTANT: Make sure there is no dirt or any other foreign material in between

the window panes.

17. Place the plastic cover onto the inner door and lock in place with the 4 tabs.

18. Place the outer door onto the inner door.

Outer

Door

Inner

Door

Top of Door

15

Reversing the door swing.

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

Reassemble Door Assembly (cont.)

19. After reversing door, there will be a mismatch between the outer door and

the inner door.

Make sure that the handle part of the outer door is opposite the hinge,

as shown.

20. Turn the door over and fasten the outer door to the inner door using

the 6 large tapping screws (#10).

STEP-BY-STEP INSTRUCTIONS (cont.)

Move Strike Bracket

21. Using a putty knife or any other flat tool, remove the 5 plastic screw caps

located on the dryer where the door will be installed and install them on

the opposite side.

22. Switch the strike bracket and its cover on the opposite side by removing

the screws; then reinstall both on the opposite side.

Reinstall Door Assembly

23. The door is now ready to be installed on the dryer. To ease this step,

the hinge has keyholes that allow a partially fastened screw to be used

as a hook.

Partially fasten a screw to the uppermost screw hole. Hook the door on the

partially fastened screw.

Fasten the hinge by installing the other 4 screws and tightening the partially

fastened screw above.

Partially

Inserted

Screw

Tighten

All

Screws

16

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

GEAppliances.com

17

Fabric Care Labels

Below are fabric care label “symbols” that affect the clothing you will be laundering.

Always follow the fabric manufacturer’s care label when laundering.

Loading and using the dryer.

Sorting and Loading Hints

As a general rule, if clothes are sorted

properly for the washer, they are sorted properly

for the dryer. Try also to sort items according to size.

For example, do not dry a sheet with socks or other

small items.

Do not add fabric softener sheets once the load

has become warm. They may cause fabric softener

stains. Bounce

®

Fabric Conditioner Dryer Sheets have

been approved for use in all GE Dryers when used

in accordance with the manufacturer’s instructions.

Do not overload. This wastes energy and causes

wrinkling.

Do not dry the following items: fiberglass items,

woolens, rubber-coated items, plastics, items with

plastic trim and foam-filled items.

Machine

wash

cycle

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Hand wash

Do not wash Do not wring

Tumble

dry

Dry

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Do not tumble dry

Do not dry

(used with

do not wash)

Heat

setting

High

Medium

Low

No heat/air

Special

instructions

Line dry/

hang to dry

Drip dry

Dry flat

In the shade

Bleach

symbols

Any bleach

(when needed)

Only non-chlorine bleach

(when needed)

Do not bleach

WASH LABELS

DRY LABELS

BLEACH LABELS

Front load

target water

temperature

Target Automatic

Category Water Temperature Temperature Control

Tap Cold Inlet Water Temperature Not used

Cold 27°C/80°F Used

Warm 40°C/105°F Used

Hot 50°C/120°F Used

Sanitize 70°C/160°F Used

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

18

Care and Cleaning of the Dryer

The Exterior: Wipe or dust any spills or washing

compounds with a damp cloth. Dryer control

panel and finishes may be damaged by some

laundry pretreatment soil and stain remover

products. Apply these products away from

the dryer. The fabric may then be washed and dried

normally. Damage to your dryer caused by these

products is not covered by your warranty.

The Lint Filter: Clean the lint

filter before each use.

Pull out the lint filter.

Moisten your fingers and

remove the captured lint.

Once clean, slide the filter

back into position. Have a

qualified technician vacuum

the lint from the dryer once a year.

NEVER OPERATE THE DRYER WITHOUT ITS FILTER

IN PLACE.

The Exhaust Duct: Inspect and clean the exhaust

ducting at least once a year to prevent clogging.

A partially clogged exhaust can lengthen the

drying time.

Follow these steps:

Turn off electrical supply by disconnecting

the plug from the wall socket.

Disconnect the duct from the dryer.

Vacuum the duct with the hose attachment

and reconnect the duct.

The Exhaust Hood: Check with a mirror that

the inside flaps of the hood move freely when

operating. Make sure that there is no wildlife

(birds, insects, etc.) nesting inside the duct

or hood.

3

2

1

Always follow the fabric manufacturer’s care label when laundering.

GEAppliances.com

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

19

Correct

Venting

Incorrect

Venting

For the best drying performance, the dryer needs to be properly vented. The dryer will use

more energy and run longer if it is not vented to the below specifications. Carefully follow

the details on Exhausting in the Installation Instructions.

 Use only rigid metal 4” diameter ductwork inside the dryer cabinet

and for exhausting to the outside.

 Do not use plastic or other combustible ductwork.

 Use the shortest length possible.

 Do not crush, kink or collapse the duct.

 Avoid resting the duct on sharp objects.

 Venting must conform to local building codes.

 Do not remove the vent protector from the back of the dryer (on some models).

 Flip the protector down to its lowest position and connect the exhaust duct

to the dryer. The lowered protector will prevent the duct from getting crushed

(on some models).

Venting the dryer.

Vent protector

in place

(on some models)

Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips

20

Stacking. GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

 IMPORTANT: Save these instructions for local

electrical inspector’s use.

 IMPORTANT: Observe all governing codes and

ordinances.

 Note to Installer – Be sure to leave these

instructions with the Consumer.

 Note to Consumer – Keep these instructions

for future reference.

 Installation must be performed by a qualified

installer.

 Proper installation is the responsibility

of the installer.

FOR YOUR SAFETY

WARNING!

 Electric Shock Hazard. Disconnect power before

installing. Failure to do so could result in serious

injury or death.

 Potential Personal Injury. More than two

people are recommended to lift the dryer into

position because of its weight and size. Failure

to do so could result in personal injury or

death.

 Avoid Tipping and Rupture of Utility Services.

Dryer must be securely attached to the washer.

DO NOT place the washer on top of the dryer.

Failure to do so could result in personal

injury/death or property damage.

 Mobile Home or Manufactured Home

Installation – Stacking of a gas dryer is not

permitted in a mobile home or manufactured

home.

MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET

INSTALLATION

Minimum clearance to combustible surfaces

and for air opening are: 0” both sides and 1” rear.

Consideration must be given to provide adequate

clearance for installation and service.

ALCOVE OR CLOSET INSTALLATION

 If your dryer is approved for installation

in an alcove or closet, it will be stated on

a label on the dryer back.

 The dryer MUST be vented to the outdoors. Refer

to dryer Installation Instructions for details.

 Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0” either side

3” front and rear

 Minimum vertical space from floor to overhead

cabinets, ceiling, etc. is 43” without pedestal,

55” with pedestal and 84” stacked.

 Closet doors must be louvered or otherwise

ventilated and must contain a minimum

of 60 square inches of open area equally

distributed. If the closet contains both a washer

and a dryer, doors must contain a minimum

of 120 square inches of open area equally

distributed.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Page is loading ...

GE DCVH680GJMV User manual

GE DCVH680GJMV User manual

in other languages

Related papers

Other documents