Metabo KHE 22 SP Bohrhammer Owner's manual

Page is loading ...

4

A

B

C

D

6.30928 6.30283 6.230386.23033

6.23034

6.23035

6.23036

6.31600

F

CODE! Key

6.22500

E

6.31800

17026895_0308 BHE_Gu incl RU.book Seite 4 Montag, 31. März 2008 8:58 08

Page is loading ...

ENGLISH

11

ENG

1 Declaration of Conformity

2 Specified Conditions of Use

3 General Safety Information

4 Special Safety Information

5Overview

6 Special Product Features

7 Start of Operation

7.1 Side handle installation

8Use

8.1 Depth stop setting

8.2 Switching on/off

8.3 Speed preselection (KHE 26 Contact)

8.4 Operating mode selection

8.5 Selection of direction of rotation

8.6

Drill chuck change

(not KHE 22 SP, KHE 24 SP,

KHE 26 SP, BHE 22, BHE 20 SP)

8.7 Tool change with SDS chuck

8.8 Tool change with Futuro Plus keyless

chuck (not for

KHE22SP, KHE24SP,

KHE 26 SP,

BHE 22,

BHE 20 SP

)

8.9 Contact mode (KHE 26 Contact)

9 Tips and Tricks

10 Maintenance

11 Trouble Shooting

12 Accessories

13 Repairs

14 Protection of the Environment

15 Technical Specifications

We, being solely responsible, hereby declare that

this product conforms to the standards and

directives specified on page 2.

With the appropriate accessories this rotary

hammer drill is suitable for impact drilling with

impact masonry bits and chiselling into concrete,

stone and other such materials, with impact core

drill bits (KHE 28, KHE Partner Edition) into

masonry and similar materials as well as for

non-impact drilling into metal, wood, etc. and for

driving screws.

The user bears sole responsibility for any damage

caused by inappropriate use.

Generally accepted accident prevention

regulations and the enclosed safety information

must be observed.

WARNING

– Reading the operating

instructions will reduce the risk

of injury.

WARNING Read all safety warnings and

instructions.

Failure to follow all safety

warnings and instructions may result in elec-

tric shock, fire and/or serious injury.

Keep all safety instructions and information for

future reference.

Before using the power tool, carefully read through

and familiarise yourself with all the enclosed safety

information and the Operating Instructions. Keep

all enclosed documentation for future reference,

and pass on your power tool only together with this

documentation.

For your own protection and for the

protection of your power tool pay

attention to all parts of the text that

are marked with this symbol!

Wear ear protectors.

Exposure to noise can

cause loss of hearing.

Use the additional handle supplied with the

tool.

Loss of control can lead to injuries.

Hold the power tool by the insulated gripping

surfaces when performing an operation where

the cutting accessory may contact hidden

Operating Instructions

Dear Customer,

Thank you for the trust you have placed in us by buying a Metabo power tool. Each Metabo power tool

is carefully tested and subject to strict quality controls by Metabo's quality assurance. Nevertheless, the

service life of a power tool depends to a great extent on you. Please observe the information contained

in these instructions and the enclosed documentation. The more carefully you treat your Metabo power

tool, the longer it will provide dependable service.

Contents

1 Declaration of Conformity

2 Specified Conditions of Use

3 General Safety Information

4 Special Safety Information

17026895_0308 BHE_Gu incl RU.book Seite 11 Montag, 31. März 2008 8:58 08

12

ENGLISH

ENG

wiring or its own cord

. Cutting accessory

contacting a "live" wire may also energise metal

parts of the power tool, resulting in an electric

shock.

Always hold the machine with both hands using the

handles provided, stand securely and concentrate.

Always wear protective goggles, gloves, and sturdy

shoes when working with this tool.

Ensure that the spot where you wish to work is

free of

power cables, gas lines or water pipes

(e.g. using a metal detector).

Metabo S-automatic safety clutch.

When the safety clutch responds, switch off the

machine immediately!

Avoid inadvertent starts by always unlocking the

switch when the plug is removed from the mains

socket or in case of a power cut. Not required for

drills with VTC electronics (restart protection).

Do not touch the rotating tool!

Remove chips and similar material only with the

machine at standstill.

Caution must be exercised when driving screws

into hard materials (driving screws with metric or

imperial threads into steel)! The screw head may

break or a high reverse torque may build up on the

handle.

Pull the plug out of the plug socket before any

adjustments or servicing are performed.

SYMBOLS ON THE TOOL:

.......Class II Construction

V...........volts

A...........amperes

Hz.........hertz

.../min...revolutions per minute

~...........alternating current

n

0

.........no load speed

Dust from material such as paint containing lead,

some wood species, minerals and metal may be

harmful. Contact with or inhalation of the dust may

cause allergic reactions and/or respiratory

diseases to the operator or bystanders.

Certain kinds of dust are classified as carcinogenic

such as oak and beech dust especially in conjunc-

tion with additives for wood conditioning (chromate,

wood preservative). Material containing asbestos

must only be treated by specialists.

- Where the use of a dust extraction device is

possible it shall be used.

- The work place must be well ventilated.

- The use of a dust mask of filter class P2 is recom-

mended.

Follow national requirements for the materials you

want to work with.

See page 3 (please unfold).

1

Keyless chuck

2

SDS chuck

3

Tool lock

4

Keyless chuck sleeve

5

Chuck lock

6

Spindle

7

Depth stop

8

Speed preselection wheel

9

Electronic signal indicator

10

Contact mode indicator

11

Contact mode

12

Rotation selector switch

13

Lock button

14

Trigger

15

Stop

16

Control knob

17

Side handle

18

SDS chuck

Exchangeable chuck

(not

KHE 22 SP, KHE 24 SP, KHE 26 SP,

BHE 22,

BHE 20 SP

):

With a simple operation and without the need for

extra tools the SDS chuck is exchanged against the

keyless chuck.

Single-knob control

With only a single control knob the operating mode

(drilling, hammer drilling, chiselling, depending on

the model) is selected.

Rotary stop:

(KHE 28, KHE 26 Contact, KHE 26, KHE 26 SP,

KHE 22 SP,

KHE 24 SP, KHE Partner Edition):

By turning the rotation off chiselling can be done.

Metabo S-automatic safety clutch:

If the insertion tool jams or hooks, the power flow to

the engine will be restricted. Because of the high

power which then arises, always hold the machine

with both hands on the handles, stand safely, and

concentrate on your work.

Auto-stop carbon brushes

If the brushes are completely worn, the machine

switches off automatically.

With VTC electronics: A LED warns before the

brushes are completely worn.

Restart protection on machines with

VTC electronics

(KHE 28, KHE 26, BHE 26, KHE 26 SP,

KHE Partner Edition)

The restart protection prevents unintentional

starting when being plugged in again or when

power is restored after a power failure.

5Overview

6 Special Product Features

17026895_0308 BHE_Gu incl RU.book Seite 12 Montag, 31. März 2008 8:58 08

ENGLISH

13

ENG

Metabo contact mode:

(KHE 26 Contact)

For intelligent drilling in walls with installed electric

or water lines. As soon as the inserted tool makes

contact with conductive, earthed material or live

supply cables, the machine switches off

immediately.

Metabo CODE! System

(KHE 28, KHE 26, BHE 26, KHE Partner Edition)

The Metabo CODE! System is an electronic anti-

theft device with which you can lock your Metabo

machines (if fitted with CODE!) to protect them

from abuse. Once locked, a machine can no longer

operate and therefore cannot be used by a

potential thief.

Wefore plugging in check to see that the

rated mains voltage and mains frequency,

as stated on the rating label, match with your

power supply.

7.1 Side handle installation

Wor safety reasons, always use the side

handle supplied.

Open the clamping ring by turning the side handle

(17) counter-clockwise. Place the side handle onto

the machine's collar. Insert the depth stop (7).

Tighten the side handle in the required angle

depending on the task at hand.

8.1 Depth Stop Setting

Loosen the side handle (17). Set depth stop (7) to

the desired drilling depth and retighten the side

handle.

8.2 Switching on/off

To start the machine, press the trigger (14).

The speed can be changed at the trigger.

This machine has an electronic soft start.

For continuous operation the trigger can be locked

with the lock button (13). To stop the machine,

press the trigger again.

If switched on continuously, the machine

continues running if it is jerked out of your

hands. Therefore, always hold the

machine with both hands on the handles, stand

safely, and concentrate on your work.

8.3 Speed preselection (KHE 26 Contact)

Depending on the application, the optimum speed

is preset with the pre-selector wheel (8).

8.4 Operating mode selection

Select the desired operating mode by turning the

control knob (16). To turn, push the stop (15).

twist drilling

hammer drilling

(only with use of hammer drill chuck)

chiselling

(KHE 28, KHE 26 Contact,

KHE 26,

KHE 22 SP,

KHE 24 SP,

KHE 26 SP, KHE Partner Edition)

(only with use of hammer drill chuck)

In chisel mode the chisel is locked to be twist-proof.

To position the chisel for the particular application,

set the control knob (16) between and

.

When a chisel is fitted, only operate

the machine in the chiselling operating

mode.

Avoid levering movements of the machine

when a chisel is fitted.

8.5 Selection of direction of rotation

Do not actuate the rotation selector

switch (12) unless the motor has

completely stopped.

Select direction of rotation:

R = clockwise

L = counter-clockwise

8.6 Drill chuck change

(not KHE 22 SP, KHE 24 SP, KHE 26 SP,

BHE 22, BHE 20 SP)

When changing chucks make sure that

the spindle is clean. Grease spindle lightly

if required.

Removing the chuck:

Turn chuck lock (5) in direction indicated by arrow

against the stop (a) and pull it off the spindle (b).

7Start of Operation

8Use

17026895_0308 BHE_Gu incl RU.book Seite 13 Montag, 31. März 2008 8:58 08

14

ENGLISH

ENG

Replacing the chuck:

Place chuck onto spindle (6) (a). Turn chuck lock

(5) in direction indicated by arrow (b) until chuck

slides fully onto the spindle, then release the chuck

lock.

Check to see that the chuck is properly seated.

Note:

To keep the spindle from turning while

changing chucks, set the control knob (16) to

chiselling.

8.7 Tool Change with SDS Chuck

Before fitting, clean tool shank and apply

special grease 6.31800! Use only

SDS-Plus tools!

Inserting the tool:

Turn the tool while inserting, until it engages. The

tool is automatically locked.

Removing the tool:

Turn tool lock (3) in direction indicated by arrow (a)

and remove the tool (b).

8.8 Tool change with Futuro Plus keyless

chuck

(not KHE 22 SP, KHE 24 SP,

KHE 26 SP, BHE 22, BHE 20 SP)

Use the keyless chuck when non-impact drilling in

metal, wood etc. and driving screws.

Insert tool. Grip the retaining ring (a) firmly and,

with the other hand, turn sleeve (b) towards "GRIP,

ZU", until the mechanical resistance which can be

felt is overcome.

Caution! The chuck is not yet fully tightened! Keep

turning (there is a "clicking" sound while turning),

until further turning is no longer possible - only now

is the tool securely tightened.

With a soft tool shank, retightening may be required

after a short period of operation.

Opening the drill chuck:

Grip the retaining ring (a) firmly and, with the other

hand, turn the sleeve (b) towards "AUF,

RELEASE".

Note:

The ratchet sound which can possibly be

heard after opening the drill chuck, is functional and

is switched off by a reverse rotation of the sleeve.

If the chuck is extremely tightened:

Unplug. Hold drill chuck with an open end spanner

at the flats on its head and turn the sleeve (b) hard

towards "AUF, RELEASE".

8.9 Contact mode

(KHE 26 Contact)

To enable the contact mode, press button (11).

If required, e.g. for drilling into steel girders or steel-

reinforced concrete walls, the contact mode can be

disabled by pressing the button (11).

The contact mode indicator (10) shows the current

setting:

Green: contact mode enabled.

Red: machine has switched off because contact

was made with conductive, earthed material or a

live supply cable.

Pull machine back and bit out of the hole

immediately. Have possible damage

properly repaired.

Off: contact mode disabled.

17026895_0308 BHE_Gu incl RU.book Seite 14 Montag, 31. März 2008 8:58 08

ENGLISH

15

ENG

Only moderate pressure is required for hammer

drilling and chiselling. Exerting a high force does

not increase performance.

When drilling deep holes, remove the drill bit

periodically from the hole to release the stone dust.

Drill tiles and other brittle materials without impact.

Keyless chuck cleaning:

After prolonged use hold the chuck vertically, with

the opening down, and fully open and close it

several times. The dust collected falls from the

opening. The application of cleaning spray to the

jaws and jaw openings at regular intervals is

recommended.

The vent slots of the machine should be cleaned

from time to time.

If the trigger (14) can not be depressed, check to

see that the direction of rotation selector

switch (12) is fully set to the R or L position.

Electronic signal indicator (9) with

VTC electronics

(KHE 28, KHE 26, KHE 26 SP,

BHE 26, KHE Partner Edition)

Rapid flashing - restart protection

When power is restored after a power supply

failure, for reasons of safety the still switched-on

machine will not start. To continue operation switch

the machine off, then on again.

Slow flashing - carbon brushes worn

The carbon brushes are almost completely worn.

If the brushes are completely worn, the machine

switches off automatically. Have the brushes

replaced by an authorized service centre.

Use only genuine Metabo accessories.

If you need accessories, check with your dealer.

For the dealer to select the correct accessory, he

needs to know the exact model designation of your

power tool.

See page 4.

A Tools with SDS-Plus shank

B Twist drills for metal and wood

C TCT core cutter

D Dust extraction kit

E Special Grease

F Metabo CODE! Key

For complete range of accessories, see

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out by

qualified electricians ONLY!

Any Metabo power tool in need of repair can be

sent to one of the addresses listed in the spare

parts list.

Please attach a description of the fault to the power

tool.

Metabo's packaging can be 100% recycled.

Worn out power tools and accessories contain

considerable amounts of valuable raw and plastic

materials, which can be recycled.

These instructions are printed on chlorine-free

bleached paper.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Guideline

2002/96/EC on used electronic and electric

equipment and its implementation in national legal

systems, used power tools must be collected sepa-

rately and handed in for environmentally compat-

ible recycling.

Explanatory notes on the information on page 2.

Changes due to technological progress reserved.

P

1

= rated input

P

2

= rated output

n

1

= no-load speed

n

2

= load speed

ø max = max. solid drill diameter

s max = max. impact rate

W = single impact strength

m=weight

D = spindle collar diameter

b = drill chuck chucking capacity

Vibration total value (vector sum of three

directions) determined in accordance with

EN 60745:

a

h, HD

= Vibration emission value

(hammer drilling into concrete)

a

h, Cheq

= Vibration emission value

(chiselling)

K

h,HD/Cheq

= Unsafe (vibration)

9 Tips and Tricks

10 Maintenance

11 Trouble Shooting

12 Accessories

13 Repairs

14 Environmetal Protection

15 Technical Specifications

17026895_0308 BHE_Gu incl RU.book Seite 15 Montag, 31. März 2008 8:58 08

16

ENGLISH

ENG

The vibration emission level given in this informa-

tion sheet has been measured in accordance with

a standardised test given in EN 60745 and may be

used to compare one tool with another. It may be

used for a preliminary assessment of exposure.

The declared vibration emission level represents

the main applications of the tool. However if the tool

is used for different applications, with different

accessories or poorly maintained, the vibration

emission may differ. This may significantly increase

the exposure level over the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the

tool is switched off or when it is running but not

actually doing the job. This may significantly reduce

the exposure level over the total working period.

Identify additional safety measures to protect the

operator from the effects of vibration such as: main-

tain the tool and the accessories, keep the hands

warm, organisation of work patterns.

Typical A-effective perceived sound levels:

L

pA

= Sound pressure level

L

WA

= Acoustic power level

K

pA

, K

WA

= Unsafe (noise level)

During operation, the acoustic level may

exceed 85 dB(A).

Wear hearing protection!

Measured values established according to

EN 60745.

The stated technical specifications are subject to

tolerances (as specified in the respective current

standards).

17026895_0308 BHE_Gu incl RU.book Seite 16 Montag, 31. März 2008 8:58 08

Page is loading ...

Metabowerke GmbH,

72622 Nürtingen, Germany

www.metabo.com

17026895_0308 BHE_Gu incl RU.book Seite 96 Montag, 31. März 2008 8:58 08

Metabo KHE 22 SP Bohrhammer Owner's manual

Metabo KHE 22 SP Bohrhammer Owner's manual

in other languages

Related papers

Other documents