SWITEL BCE11 Owner's manual

Babyphone

Interphone bébé

Sorveglia bebé

Babyphone

BCE11

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Operating Instructions

XXXX

Page is loading ...

19

2 Safety Information

Please read this operating instruction manual thoroughly. Under no

circumstances open the device or complete any repair work your-

self. In the case of claims under the terms of guarantee, contact

your sales outlet. We reserve the right to make technical and optical

modifications to the product during the course of product improve-

ment.

1. Intended use

This babyphone enables you to monitor your child(s) whereever you

are in or arround your house.

2. Installation location

The equipment must be set up in the vicinity of a 230 Volt mains

power outlet.

Place the babyphone on a level, non−slip surface. Normally, the

footpads on the babyphone do not leave any marks on the surface

where it is located. However, due the diverse types of paints and

surfaces which come into question, it cannot be fully ruled out that

the footpads will leave marks on the surface on which it is located.

3. Power supply

Only use the SWITEL power adapter plug supplied because other

power supplies could destroy the babyphone. Do not open the

power adapter plug. There is a risk of fatal injury if the power adap-

ter plug is opened and not disconnected from the power supply.

4. Information on disposal

The implementation of European law in national laws and directives

obliges you to dispose of consumable goods appropriately. This ser-

ves to protect both persons and the environment.

The adjacent symbol indicates that electrical and

electronic apparatus no longer required must be

disposed of separate from domestic waste.

Equipment which is old or has outlived

its service life must be disposed of at a suitable

collection point provided by the public waste authorities.

Batteries and power packs must be disposed of at

the point of sale or at the appropriate collection points

provided by the public waste authorities.

Packaging materials must be disposed of according to local re-

gulations.

5. Important

 Before using the wireless babyphone, check the sound

transmission. This checks whether units are placed out of

range of each other, sound transmission should be checked on

a regular basis as follows: Have an adult softly speak into the

"Baby unit", sounds transmitted from the baby’s room and

should be heard clearly via "Parent unit" in another room.

20

 Do not place the "baby unit" and "parent unit" too closely during

Operation. Otherwise, the units may start resonating.

 When use the power adapter in house, do not place it closely

to your child, under a window or in any other place where your

child might reach it.

 The power adapter should not be used with other equipment in

any circumstances. And any other product adapter is not

suitable for this System.

 Following factors may fluctuate the Operation distance, such

as battery power, obstructions of wall, radio waves and terrain.

Please try to switch to another channel or move "parent unit"

closer to "baby unit" to get better performance.

3 Feature List

Congratulation, you have purchased our wireless babyphone. It in-

cludes a "baby unit" (Transmitter), a "parent unit" (Receiver) and

one AC power adapter as shown in fig. I.

1. Wireless RF transmission

2. 2−Channel selection

3. "Baby unit " with night light function

4. Voice activated transmission and night light (choose AUTO

MODE) with sensitivity tuning

5. "Parent unit" with mute function, noise elimination and power

saving

6. "Baby unit" with 9V AC power adapter (Included) operation or

4 "AAA" batteries backup (Not included)

7. "Parent unit" with 3 "AAA" batteries (Not included) or

rechargeable battery (not included) operation, or power adapter

(not included) operation. (9V DC, 200 mA, female plug, centre

negative (−))

8. "Parent unit" with volume control

9. AC power adapter jack optional on both units

10. Low battery indicator

11. Low current consumption and Iow RF radiation

12. "Parent unit" with belt clip

13. Night light OFF/AUTO/ON switch

4 Installation

1. Battery Installation (all the batteries not included)

Only use CE certificated batteries

 Open the battery cover on both units as shown in fig. II.

 Install 4 "AAA" batteries in correct polarity direction into the

"baby unit"; install 3 "AAA" batteries with correct polarity

direction into the "parent unit".

21

 Replace the battery cover.

2. Power Adapter Connecting

Only use CE certificated adapter

 Plug power adapter (included) to the DC 9V Jack of "baby unit"

and AC outlet (Fig. III )

 For a long term usage at a fix location in house of the "parent

unit", you can buy a power adapter (9V DC, 200 mA, female

plug centre negative (−)) to plug the power adapter

(not included) to the DC 9V jack of "parent unit" and AC outlet

(Fig. IV).

 Set channel selection of "baby unit" and "parent unit" to the

same channel "A" or "B".

 When the units will not be used for a long time, should

remove all the batteries, otherwise, the battery may leak

and damage the units.

 Each of the "baby unit" and "parent unit" has a Iow battery

indicator. If the Iow battery LED lights up, please replace

new batteries.

 The adapter of both units Output DC 9V 200 mA female

plug, centre negative (−) is recommended.

 If the units are both installed with batteries and connected

adapters. Even AC power failure, the units will continue to

work with batteries.

 Only Use CE Certificated Power Supply

5 Operation

1. "Baby Unit" (Transmitter)

 Make sure the AC power adapter is connected or batteries are

installed correctly.

 Place the "Baby unit" near the baby’s bed, making sure that the

microphone is placed in the best position for picking up baby’s

sound. (Fig. V)

Ensure the unit to be out of reach from your child. Never

place it inside baby’s bed or playpen!

 Turn the power switch ON and the power indicator LED will

light up. When sound is picked up by the built−in microphone,

the "baby unit" starts transmitting signal automatically to

"parent unit". The transmission will stop when no sound is

picking up any more.

 Set the night light switch as you want: OFF mode no night light

function; AUTO mode activate by voice; ON mode night light

will continuing light up.

22

2. "Parent Unit" (Receiver)

 Make sure that the batteries are installed or the adapter is

connected correctly.

 Place the "parent unit" near to the parents’ location (Fig. V).

 Turn the POWER/VOLUME control on and adjust volume as

required, the power indicator LED will light up. If a sound signal

is received from the "baby unit", the "Parent unit" indicator LED

will light up.

3. Channel Selection

 The unit set 2 different channels for radio Signal transmission.

If the reception is poor or interference radio Signals are being

picked up, please change switch to the other channel in order

to get optimum reception.

Always make sure that channel switches to the same

channel for both units.

4. Tuning The Voice Activating Sensitivity

 In normal circumstance the factory preset sensitivity level to

the most applications is recommended, unless you feel voice

transmission difficult, you can use a flat screwdriver to adjust it

as below (Fig.VI):

a) To turn clockwise to increase sensitivity.

b) To turn counter anti−clockwise. to reduce the sensitivity.

5. Belt Clip

 After the batteries is connected to the "parent unit", you can

carry it for your convenience at your home by using the belt

clip. (Fig. VII )

6 Trouble Shouting

1. Non−operation situation

 Check the "baby unit" and the "parent unit" is at the same

channel.

 Ensure the "baby unit" and the "parent unit" batteries or power

adapter are connected properly.

2. Wireless RF transmission range too small

 Check if the battery is Iow. If so, please replace new batteries

 Check if there is interference, remove the interference source.

 Adjust voice sensitivity according to point 4 in Operation

section to get Optimum transmission.

23

7 Technical Specifications

Item Specifications Remarks

Battery type

xPcs

Tx. 1,5V (AAA) x4

Rx. 1,5 V (AAA) x3

not included

Standby current Tx. 6 mA

Rx. 18~24 mA

Tx. 9V DC

Rx. 4,5V DC

Operation Cur-

rent

Tx. 40~120 mA

Rx. 18~110 mA

Rf Frequency CH−A: 40.965MHz or. . .

49.860MHz. . . . . . . .

CH−B: 40.665MHz or. . .

49.830MHz. . . . . . . .

Battery Backup

time

Up to 200 hours

Up to 15 hours

Tx: Alkaline

battery

Rx: Alkaline

battery

Power adapter 9V DC, 200 mA, female

plug, center (−)

Included for

Tx only

Tx=Transmitter, Rx=Receiver

Declaration of conformity

WE TELGO AG

OF Route d’Englisberg 17

CH−1763 Granges−Paccot

Declare under our own responsibility that the product

MODEL: BCE11

DESCRIPTION: Cordless DECT telephone

Is in conformity with directives: R&TTE Directive (1999/5/EC)

AUTHORISED BY:

________________________

Signed:

Name (printed): Selim Dusi

Position in company: Managing Director

Date of issue:

Copies of this document will be held on file for a period of 10

years after the last production.

Supplier:

TELGO AG, Route d’Englisberg 17

CH−1763 Granges−Paccot

Product: BCE11

This product is intended for connection to analogue PSTN lines within Switzerland.

However, due to differences between the individual PSTNs provided in the different

countries, the approval does not, of itself, give an unconditional assurance of successful

operation on every PSTN network termination point.

SWITEL BCE11 Owner's manual

SWITEL BCE11 Owner's manual

in other languages

Related papers

Other documents