Jaguar VOICE ACTIVATION X-TYPE 2001.5 User manual

X-TYPE 2001.5 MY

VOICE ACTIVATION

HANDBOOK

North American Markets Only

Go to Foreword >>

Go to Contents >>

Go to Index >>

Foreword

Jaguar X-TYPE

Voice Activation Handbook

Published May 2001 by Parts and Service Communications Jaguar Cars Limited Publication Part No. JJM 18 09 20/15

JAGUAR CARS LIMITED,

as manufacturers, are

dedicated to the design and production of vehicles which meet

the expectations of the world’s most discerning purchasers.

To complement the features, systems and technology of your

new vehicle we have produced this Voice Activation Handbook.

In it we have undertaken to make the control of complex

systems easy to understand and operate.

The information contained herein applies to a range of vehicles

and not to a specific vehicle. For the specification of a particular

vehicle, owners should consult their Jaguar Dealer.

The Manufacturer reserves the right to vary its specifications

with or without notice, and at such times and in such manner as

it thinks fit. Major as well as minor changes may be involved in

accordance with the Manufacturer’s policy of constant product

improvement.

reproduced, stored in a retrieval system or transmitted, in any

form, electronic, mechanical, photocopying, recording or other

means without prior written permission from the

Service Division of Jaguar Cars Limited.

Contents

General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Using the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

How to say numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Voice command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Voice command synonyms . . . . . . . . . . . . . . . . . . . . . . . . . 13

Voice command descriptions . . . . . . . . . . . . . . . . . . . . . . . . 15

Voice training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Training command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Trouble shooting error messages . . . . . . . . . . . . . . . . . . . . . 34

A comprehensive index is located at the back of this handbook.

Voice activation 1

General information

This Handbook describes every option and model variant

available and therefore, some of the items covered may not

apply to your particular vehicle.

Introduction

Voice activation provides a safe and convenient way of

controlling the following vehicle systems (where fitted):

• Sound system (radio, cassette tape player and CD changer)

• In-car telephone

• Climate control system

•Navigation

•Display screen

The system is controlled by the Voice button on the top

left-hand side of the steering wheel. Voice commands are

picked up by the microphone in the overhead console; this

microphone is used for voice activation and for the in-car

telephone. When giving a command, voice feedback will be

heard through the sound system speakers, and messages will be

shown on the instrument cluster message centre, sound system

panel, phone handset, climate control panel, or display screen.

For on-line help on using the system press and release the voice

button, then after the beep give the voice command HELP.

Commands can be personalised using nametags, which allow a

name or phrase to be used to dial a phone number, tune to a

radio station or select a navigation destination.

Voice feedback can be turned off if required.

!

WARNING:

Concentrate on the current road conditions and driving

the vehicle at all times. If the voice system does prompt

you for a response it will repeat that prompt twice giving

you up to 15 seconds to respond. If driving conditions

mean that you are unable to respond, the voice system

will timeout, cancel the task and will not make any

changes to the vehicle settings.

Language and accent

Commands are given in English using a natural speaking voice,

without pausing between words. Most accents are understood

without difficulty, but the system also allows you to train the

voice system with your voice if required, see Voice training on

page 30.

2 Voice activation

General information (continued)

Key to illustration

Vehicles fitted with navigation system:

1. Message centre display.

2. Microphone.

3. Voice button.

4. Menu button.

5. Display screen.

Voice activation 3

General information (continued)

Key to illustration

Vehicles NOT fitted with navigation system:

1. Message centre display.

2. Microphone.

3. Voice button.

4. Mode button, on radio.

5. Seek/tuning control, on radio.

(Used to commence voice training).

4 Voice activation

Using the system

Initialisation

When the ignition switch is turned to position ‘ll’ (ignition on),

the system is enabled. After initialisation, which takes about ten

seconds, the system is ready to accept voice commands. If the

Voice button is pressed before initialisation is complete, an

advisory tone will be heard and the message centre display will

show ‘VOICE NOT READY’.

Notes:

1. The system will not operate until the radio security code has

been entered.

2. Voice commands to the navigation system will only operate

after the navigation Caution Screen has been cleared. This

must be done after every ignition cycle.

Giving voice commands

When a voice command is given, the vehicle will automatically

switch on the system required to carry out the command, as

described in the following example:

To select track 5 of the CD changer when the sound system is

off, give the command CHANGER PLAY TRACK 5. The vehicle

will turn on the sound system, select the CD changer and play

track 5. There is no need to turn on the sound system and select

the appropriate source.

The procedure for giving a voice command is as follows:

1. Press and release the Voice button and wait for the end of the

listening beep. The message centre shows LISTENING.

2. After the beep, say any command from the list of commands

recognized by the system, see Voice command list on

page 9. Speak in a natural voice without pausing between

words. For commands that contain numbers, see How to

say numbers on page 7.

3. After saying the command, wait for the system to recognize

the end of the command.

4. If you are prompted by the voice system for a response, you

must first press and release the Voice button, wait for the end

of the listening beep and then respond.

5. After processing, the command is shown on the message

centre and confirmed by voice feedback (if turned on). The

requested action is then carried out.

Command help

There are commands available which give spoken help for the

voice commands. This provides a useful reminder of the

commands available while driving. The commands are: HELP,

VOICE HELP, VOICE MEMORY HELP, RADIO HELP,

RADIO MEMORY HELP, TAPE HELP, CHANGER HELP,

PHONE HELP, PHONE MEMORY HELP, CLIMATE CONTROL

HELP, NAVIGATION HELP,NAVIGATION MEMORY HELP,

NAVIGATION ROUTE HELP and DISPLAY HELP. For further

information, see Voice command descriptions on page 15.

Voice activation 5

Using the system (continued)

Command confirmation and prompts

After a command has been given, the system will give feedback

of what it understood. The verbal feedback given can be

switched on or off by using the VOICE FEEDBACK ON or VOICE

FEEDBACK OFF commands. When off, feedback is still given for

help commands, directory listings, prompts, error messages and

nametags.

Visual confirmation of each voice command is shown on the

message centre. For radio and phone number nametags, the

radio station frequency or phone number associated with the

nametag is shown. NAVIGATION NAMETAG will be shown

when a stored navigation location is recalled. Messages will also

be shown on the system which is being controlled by the voice

command.

During some commands and for voice training, the user is

prompted by the system to respond. In such cases the user must

press and release the voice button then speak after the beep. If

the user does not respond to the system within five seconds, the

system will prompt twice more before the command is

canceled. This gives the user up to fifteen seconds to respond to

a system prompt.

For the phone dial commands, the system will prompt for

conformation before making the call. This confirmation can be

switched on or off by giving the PHONE CONFIRMATION ON

or PHONE CONFIRMATION OFF command.

Nametags

Nametags are a unique user defined name or phrase which can

be used to recall a radio station, dial a phone number or set a

route to a navigation memory point.

For radio commands, RADIO TUNE nametag is used to select a

station that has been previously stored using the RADIO STORE

NAME command.

For phone commands, PHONE DIAL nametag is used to call a

phone number that has been previously stored using the

PHONE STORE or PHONE ENTER command. Phone numbers

held in voice system memory are quite separate from numbers

held in the phone system memory. (To call a number held in the

phone memory, use the PHONE DIAL MEMORY command.)

For navigation commands NAVIGATION SELECT DESTINATION

nametag is used to select a location previously stored using the

NAVIGATION STORE NAME command. These locations can

then be recalled as destinations or waypoints as required.

Navigation memory points with a nametag also appear as part of

the navigation directory of stored locations.

A spoken list of current nametags can be heard by giving the

appropriate directory command see Voice command list on

page 9. There are also commands for deleting either individual

names in a directory, or a complete directory.

Notes:

1. Nametags should not be stored when the environment is

noisy, for example whilst travelling at speeds above 60mph

(100kph), whilst other occupants are talking or with windows

or sunroof open. Nametags recorded in these situations will

contain much more background noise, making them more

easily confused with other commands.

6 Voice activation

Using the system (continued)

2. If the user tries to store a nametag, which sounds

phonetically similar to a nametag already stored, or to the

word DIRECTORY, the system will advise the user that this

nametag cannot be stored. In addition, for phone nametags,

phrases that sound like phone numbers are not allowed. For

radio nametags, phrases that sound like radio frequencies,

are not allowed. This is to prevent the user storing a nametag,

which cannot then be recalled because it sounds too much

like another nametag or command.

Volume level adjustment

The speaker volume level can be adjusted independently for the

voice activation system. To adjust, operate the sound system

volume control or the steering wheel volume control during a

voice command or voice training. The speaker volume level can

also be adjusted within the volume preset menu of the audio

system. Also see the Audio Systems Handbook.

Notes:

1. Voice commands cannot be given while a hands free phone

call, radio traffic announcement or navigation guidance is in

progress.

2. If the voice button is pressed whilst a radio traffic

announcement is in progress the announcement will be

canceled. Press the voice button again to start a voice

session.

3. While LISTENING is displayed on the message centre, the

command can be canceled by pressing the Voice button,

except when using the PHONE ENTER command. To cancel

a PHONE ENTER voice session either say CANCEL when

LISTENING is displayed or press the voice button and after

the end of the beep say CANCEL. During a store nametag

session, if the voice button is pressed and released during

LISTENING the system will take up to 2 seconds to cancel.

4. Voice feedback can be interrupted by pressing the Voice

button whilst the feedback is playing.

5. After starting to speak, the command must be completed

within 10 seconds.

6. Excessive noise, for example while driving with windows

open or in demist mode, may cause voice command

misrecognition. If it is too noisy to use the phone, it is likely

that voice commands will not be recognized.

7. During a voice command the audio system and indicator

ticking will be muted.

8. The voice session will be canceled if an alternative message

requires the display/speaker (e.g. incoming phone call, radio

traffic announcement or navigation guidance).

Voice activation 7

How to say numbers

Numbers in voice commands must be given as shown below.

Either ‘zero’ or ‘oh’ can be used for ‘0’, most users will find that

‘zero’ gives better results. For information about specific

commands, see Voice command descriptions on page 15.

Radio stations

Frequencies are said as in the following examples:

• ‘Tune five thirty one AM’, or ‘Tune five thirty one’ (531).

• ‘Tune nine hundred’ (900).

• ‘Tune fourteen forty’ (1440).

• ‘Tune fifteen oh three AM’ (1503).

• ‘Tune ten eighty’ (1080).

• ‘Tune eighty nine point nine FM’, or ‘Tune eighty nine point

nine’ (89.9).

• ‘Tune ninety point zero’, or ‘Tune ninety’ (90.0).

• ‘Tune one hundred point five’ (100.5).

• ‘Tune one oh one point one FM’ (101.1).

• ‘Tune one oh eight point oh’, ‘Tune one oh eight point zero’,

or ‘Tune one oh eight’ (108.0).

Disc and track numbers

For CD changer commands, say disc and track numbers as in

the following examples:

•‘Disc one’ (1).

• ‘Disc six track ten’ (6, 10).

• ‘Track twenty five’ (25).

• ‘Track forty seven’ (47).

8 Voice activation

How to say numbers (continued)

Phone numbers

All phone numbers are said as single digits, as in the following

example. Star (∗) and Pound (#) are acceptable as the first digit

of a number.

• ‘Dial one two zero one eight one eight eight one zero zero’

(1-201-818-8100).

When using the Phone Enter command, the first entry must be

between 2–16 digits, then, 1–16 digits to a maximum of 32 in

total.

Temperatures

In climate control commands, say temperatures as in the

following examples:

• ‘Temperature seventy two’ (72).

• ‘Temperature eighty’ (80).

• ‘Temperature twenty one point five’ (21.5).

• ‘Temperature nineteen point zero’, ‘Temperature nineteen

point oh’ or ‘Temperature nineteen’ (19.0).

Voice activation 9

Voice command list

All the commands recognized by the system are shown in the

list below. Optional words that can be omitted are shown in

square brackets. Phrases shown in round brackets are optional

ways of giving the command; one of the options separated by

the forward slashes, must be given. Data items that you need to

input, such as phone numbers, are shown in italics. For an

explanation of each command, see Voice command

descriptions on page 15.

General commands

•HELP

•VOICE HELP

•VOICE MEMORY HELP

• VOICE FEEDBACK (ON/OFF)

• PHONE CONFIRMATION (ON/OFF)

• VOICE [PLAY] DIRECTORY

• VOICE DELETE MEMORY (A/B)

• VOICE DELETE DIRECTORY

• YES - after prompt

• NO - after prompt

• CANCEL - after prompt

Radio commands

• RADIO PLAY

• RADIO OFF

• RADIO SEEK [UP]

• RADIO SEEK DOWN

• (RADIO TUNE/RADIO/TUNE) frequency [FM/AM]

• RADIO TUNE nametag

• [RADIO] [TUNE] PRESET preset number 1–9

• [RADIO] [TUNE] [BAND] (FM/AM)

• RADIO STORE NAME

• [RADIO] STORE PRESET preset number 1-9

• RADIO AUTOSTORE

• RADIO [PLAY] DIRECTORY

• RADIO DELETE nametag

• RADIO DELETE DIRECTORY

• RADIO HELP

• RADIO MEMORY HELP

10 Voice activation

Voice command list (continued)

Cassette tape player commands

• TAPE PLAY

•[TAPE] REVERSE

•[TAPE] REWIND

• [TAPE] FAST FORWARD

• TAPE SEEK [UP]

• TAPE SEEK DOWN

• [TAPE] DOLBY (ON/OFF)

•TAPE HELP

CD changer commands (where fitted)

•CHANGER PLAY

• [CHANGER] [PLAY] DISC disc number

• [CHANGER] [PLAY] TRACK track number

• [PLAY] TRACK track number

• [CHANGER] [PLAY] DISC disc number TRACK track number

• [CHANGER] MIX TRACKS

• [CHANGER] MIX ALL

• [CHANGER] MIX OFF

• CHANGER HELP

Phone commands (where fitted)

•PHONE ON

•PHONE OFF

• [PHONE] ENTER phone digit (2–16 digits)

Then press and release the voice button, wait until the end

of the beep and continue with one of the following:

more digits (1–16 digits)

DIAL

STORE (nametag when prompted)

CORRECTION

or CANCEL

• [PHONE] DIAL phone number (5–16 digits)

• [PHONE] REDIAL

• [PHONE] DIAL nametag

• [PHONE] DIAL MEMORY memory number

•PHONE STORE phone number (2-16 digits), (nametag when

prompted)

• PHONE [PLAY] DIRECTORY

• PHONE DELETE nametag

• PHONE DELETE DIRECTORY

• PHONE CONFIRMATION (ON/OFF)

• PHONE HELP

•PHONE MEMORY HELP

Voice activation 11

Voice command list (continued)

Automatic climate control commands (where fitted)

• CLIMATE CONTROL ON

• CLIMATE CONTROL OFF

• [CLIMATE CONTROL] AUTOMATIC [ON]

• (CLIMATE CONTROL TEMPERATURE/CLIMATE CONTROL/

TEMPERATURE) temperature [DEGREES]

• (CLIMATE CONTROL TEMPERATURE/CLIMATE CONTROL/

TEMPERATURE) (HIGH/LOW)

• [CLIMATE CONTROL] RECIRC [ON] - disabled in defrost

mode.

• [CLIMATE CONTROL] DEFROST [ON]

• CLIMATE CONTROL HELP

Navigation commands (where fitted)

• [NAVIGATION] SHOW DESTINATION

• [NAVIGATION] SHOW [CURRENT] POSITION

• [NAVIGATION] SHOW [COMPLETE/ENTIRE/WHOLE]

ROUTE

• [NAVIGATION] SHOW NORTH UP

• [NAVIGATION] SHOW (HEAD/HEADING) UP

- detailed

map scales only

• [NAVIGATION] ZOOM IN (MAX/MAXIMUM)

• [NAVIGATION] ZOOM OUT (MAX/MAXIMUM)

• [NAVIGATION] [SELECT] ROUTE HOME

• [NAVIGATION] REROUTE

• [NAVIGATION] (VOICE GUIDANCE ON/MUTE OFF)

• [NAVIGATION] (VOICE GUIDANCE OFF/MUTE ON)

• [NAVIGATION] REPEAT [LAST] INSTRUCTION

• [NAVIGATION] [SELECT] ZOOM LEVEL zoom level 1- 13

• [NAVIGATION] CLEAR ROUTE

• [NAVIGATION] SHOW TURN LIST

• [NAVIGATION] ZOOM IN zoom increment level 1-12

12 Voice activation

Voice command list (continued)

Navigation commands (continued)

• [NAVIGATION] ZOOM OUT zoom increment level 1-12

• NAVIGATION STORE NAME

• [NAVIGATION] [SELECT] DESTINATION nametag

• [NAVIGATION] ADD WAYPOINT nametag

• [NAVIGATION] MINIMISE DISTANCE

• [NAVIGATION] MINIMISE TIME

• [NAVIGATION] PREFER MAJOR ROADS

• [NAVIGATION] AVOID MAJOR ROADS

• [NAVIGATION] PREFER TOLL ROADS

• [NAVIGATION] AVOID TOLL ROADS

• [NAVIGATION] PREFER FERRIES

• [NAVIGATION] AVOID FERRIES

• NAVIGATION [PLAY] DIRECTORY

• NAVIGATION DELETE nametag

• NAVIGATION DELETE DIRECTORY

• NAVIGATION HELP

• NAVIGATION ROUTE HELP

• NAVIGATION MEMORY HELP

Navigation traffic information commands (where fitted)

• NAVIGATION TRAFFIC INFO ON

• NAVIGATION TRAFFIC INFO OFF

Display commands (where fitted)

• DISPLAY ON

• DISPLAY OFF

• [DISPLAY] [SELECT] DAY COLORS

• [DISPLAY] [SELECT] NIGHT COLORS

• [DISPLAY] [SELECT] TWILIGHT COLORS

• [DISPLAY] [SELECT] AUTOMATIC COLORS

• [DISPLAY] SHOW NAVIGATION

• [DISPLAY] SHOW AUDIO

• [DISPLAY] SHOW CLIMATE CONTROL

• [DISPLAY] SHOW PHONE

• DISPLAY HELP

Voice activation 13

Voice command synonyms

If preferred, the synonyms described in the following table can be used in place of the primary or preferred word in the voice

commands described on the previous page. When a synonym or alternative phrase is used, the voice system will feedback the primary

version of the command and not the phrase spoken by the user.

Primary word Synonyms

All Commands Info Information

Seek Search

Phone Telephone

Navigation Map

No Cancel

Radio Play On

Tune Select, except RADIO TUNE nametag

Tape Tape Cassette

Play On

Reverse Change Side

14 Voice activation

Voice command synonyms (continued)

Changer Changer Play Changer On

Play Select (for disc and track commands only)

Mix Shuffle/Random

Changer CD Changer

Disc CD

Phone Redial Recall

Climate Control Climate Control Climate

Defrost Demist

Display Display Screen

Primary word Synonyms

Voice activation 15

Voice command descriptions

In the command descriptions, optional words are shown in

square brackets. Data items that you need to enter, such as

phone numbers, are shown in italics. For information on

entering numbers in commands, see How to say numbers on

page 7.

General commands

•HELP

Gives spoken information about the voice activation system.

•VOICEHELP

Lists all voice command help messages available.

•VOICE MEMORY HELP

Gives spoken information on the use of voice memories.

• VOICE FEEDBACK (ON/OFF)

Turns voice feedback on or off.

• PHONE CONFIRMATION (ON/OFF)

Switches on or off the system confirmation prompt before

making a call when using the PHONE DIAL or PHONE

MEMORY DIAL command.

• VOICE [PLAY] DIRECTORY

Gives a spoken list of voice memories currently trained.

• VOICE DELETE MEMORY (A/B)

Deletes the trained voice stored in memory A or B.

• VOICE DELETE DIRECTORY

Deletes all stored trained voice models.

Radio commands

• RADIO PLAY or RADIO ON

Turns the sound system on and selects the last radio station

to be played.

• RADIO OFF

Turns the sound system off.

• RADIO SEEK [UP], RADIO SEEK DOWN

Seeks up or down the current waveband until the next

station is found.

• (RADIO TUNE/RADIO/TUNE) frequency [FM/AM]

Tunes to the frequency given in the command.

The frequency ranges are:

FM - 87.9 to 107.9 MHz in steps of 0.2 MHz.

AM - 530 to 1710 KHz in steps of 10 KHz

If an invalid frequency is given, the voice system will either

respond with COMMAND NOT RECOGNIZED or will

recognize a similar sounding frequency.

16 Voice activation

Voice command descriptions (continued)

Radio commands (continued)

• RADIO TUNE nametag

Selects the stored station with the nametag given in the

command.

• [RADIO] [TUNE] PRESET preset number (1–9)

Selects the stored station corresponding to the preset

number (1 to 9) given in the command.

• [RADIO] [TUNE] [BAND] (FM/AM)

Tunes to the waveband given in the command and selects

the last station played.

• RADIO STORE NAME

Stores the currently selected station, with a nametag, in the

voice system memory. After each prompt press and release

the voice button, wait until the end of the beep, then speak.

A total of 20 nametags can be stored.

Note: The sound system must be in radio mode before

giving the RADIO STORE NAME command. The system may

not accept some nametags, see Nametags on page 5.

• [RADIO] STORE PRESET preset number (1-9)

Stores the currently selected station to the preset given in

the command.

Note: The sound system must be in radio mode before

giving the RADIO STORE PRESET command.

• RADIO AUTOSTORE

Activates the Autostore or Auto Memory feature of the radio

(see audio handbook).

• RADIO DELETE nametag

Deletes the radio nametag given in the command from the

voice system memory. The system will request confirmation

from the user before deleting the nametag.

• RADIO DELETE DIRECTORY

Deletes all currently stored radio nametags from the voice

system memory. The system will request confirmation from

the user before deleting the nametags.

Voice activation 17

Voice command descriptions (continued)

Radio commands (continued)

• RADIO [PLAY] DIRECTORY

Gives a spoken list of station nametags and frequencies

currently stored in the voice system memory.

• RADIO HELP

Gives spoken information about the radio voice commands.

• RADIO MEMORY HELP

Gives spoken information about storing radio presets and

radio nametags.

Cassette tape player commands

If there is not a tape loaded, the audio system will display an

error and will continue to play the current sound system audio.

If the sound system was off with no tape loaded when the

command was given the radio will turn on.

• TAPE PLAY and TAPE ON

Selects the cassette tape player. Any tape currently loaded

will start to play.

• [TAPE] REVERSE

Reverses the direction of the cassette tape being played.

The other side of the tape is played from the current

position of the tape.

•[TAPE] REWIND

Rewinds the tape to the start of the side currently selected.

The current side will then be played. Give the TAPE PLAY

command to stop rewinding and resume play.

•[TAPE] FAST FORWARD

Fast forwards the tape until the end of the side currently

selected. The opposite side will then be selected and played.

Give the TAPE PLAY command to stop fast forward and

resume play.

• TAPE SEEK [UP], TAPE SEEK DOWN

Winds the tape forwards/backwards to the end/beginning of

the current track and then plays.

•[TAPE] DOLBY ON/OFF

Turns the Dolby noise reduction facility on or off. This

command is only available whilst playing a tape.

•TAPEHELP

Gives spoken information about the tape voice commands.

Page is loading ...

Jaguar VOICE ACTIVATION X-TYPE 2001.5 User manual

Jaguar VOICE ACTIVATION X-TYPE 2001.5 User manual

Related papers

Other documents