AV6**P
LV6**P
RV6**P
ANALOGUE
Series
00GB_AVLVRV655P_Euro1.book Page 1 Wednesday, August 26, 2009 5:20 PM
2
English
Contents
INSTALLING YOUR TV
Safety Precautions ..................................................4
Installation and important information ....................5
The remote control .................................................6
The remote control .................................................7
Inserting batteries and effective range of the
remote ..........................................................7
CONNECTING YOUR TV
Connecting external equipment ..............................8
Connecting an HDMI™ or DVI device to the HDMI
input ...................................................................9
To connect an HDMI device ..............................9
To connect a DVI device ...................................9
Connecting a computer ........................................10
To connect a PC to the RGB/PC terminal ........10
To connect a PC to the HDMI terminal ............10
Controls and input connections .............................11
Switching on ..................................................11
Using the remote control ...............................11
Using the controls and connections ................11
SETTING UP YOUR TV
Startup Application ...............................................12
Quick Setup ...................................................12
Manual Tuning .....................................................13
Tuning ...........................................................13
Skip ...............................................................14
Sorting Positions ............................................15
Auto Tuning ...................................................15
Other feature .......................................................15
Location Setting .............................................15
CONTROLS AND FEATURES
General controls ..................................................16
Selecting Positions ......................................... 16
Channel List .................................................. 16
Time Display ................................................. 16
Stereo and Bilingual Transmissions ................ 16
Quick Menu .................................................. 16
Sound controls .....................................................17
Volume Controls and Mute Sound .................17
Dual ............................................................. 17
Bass, Treble and Balance ............................... 17
Advanced Sound Settings ..............................17
Stable Sound
®
............................................... 17
Widescreen viewing ............................................. 18
Picture controls .................................................... 20
Picture Position ..............................................20
Picture Mode ................................................. 20
Picture Preferences ........................................21
Black/White Level .......................................... 21
Cinema Mode ............................................... 21
Colour Temperature ...................................... 21
Resetting the Picture Settings ......................... 22
3D Colour Management ................................22
Base Colour Adjustment ................................ 22
Active Backlight Control .................................23
Auto Brightness Sensor* ................................23
MPEG NR – Noise Reduction .......................... 23
DNR – Digital Noise Reduction ....................... 23
Automatic Format (Widescreen) .....................23
4:3 Stretch .................................................... 23
Blue Screen ................................................... 24
Side Panel Adjustment ................................... 24
Picture Still .................................................... 24
* LV6**P and RV6**P Series only
00GB_AVLVRV655P_Euro1.book Page 2 Wednesday, August 26, 2009 5:20 PM
3
English
Enjoying photo through USB port ..........................25
Opening Photo Viewer ...................................25
Viewing Photo Files ........................................26
Other features ......................................................27
Panel Lock .....................................................27
TOSHIBA Illumination* ...................................27
Timers ..................................................................27
Sleep Timer ...................................................27
On Timer .......................................................28
On Timer Position ..........................................28
Reset TV ...............................................................28
Reset TV ........................................................28
PC Settings ...........................................................29
Horizontal and Vertical Position .....................29
Clock Phase ...................................................29
Sampling Clock .............................................29
Reset .............................................................29
Input selection and AV connections .......................30
Input Selection ...............................................30
INPUT Signal Selection ...................................30
PC Audio .......................................................30
HDMI1 Audio ................................................31
TEXT SERVICES
Text services .........................................................32
Selecting Modes ............................................32
Text Information ............................................32
Navigating Pages Using Auto .........................32
Navigating Pages Using LIST ..........................32
Control Buttons ..............................................33
PROBLEM SOLVING
Questions and Answers ......................................34
INFORMATION
Notes ...................................................................36
Information ..........................................................37
Specifications and accessories ...............................39
* RV6**P Series only
00GB_AVLVRV655P_Euro1.book Page 3 Wednesday, August 26, 2009 5:20 PM
4
English
INSTALLING YOUR TV
Safety Precautions
This equipment has been designed and manufactured
to meet international safety standards but, like any
electrical equipment, care must be taken to obtain the
best results and for safety to be assured. Please read
the points below for your own safety. They are of a
general nature, intended to help with all electronic
consumer products and some points may not apply to
the goods you have just purchased.
Leave more than 10cm clearance around the television
to allow adequate ventilation. This will prevent
overheating and possible damage to the television.
Dusty places should also be avoided.
Damage may occur if the television is left in direct
sunlight or near a heater. Avoid places subject to
extremely high temperatures or humidity. Place in a
location where the temperature remains between 5°C
(41°F) min. and 35°C (94°F) max.
The mains supply required for this equipment is 220-
240V AC 50/60Hz. Never connect to a DC supply or
any other power source. DO ensure that the television
is not standing on the mains lead. Use only the
supplied lead.
DO NOT cut off the mains plug from this equipment,
this incorporates a special Radio Interference Filter, the
removal of which will impair its performance.
IF IN DOUBT PLEASE CONSULT A COMPETENT
ELECTRICIAN.
DO
read the operating instructions before you attempt
to use the equipment.
DO
ensure that all electrical connections (including the
mains plug, extension leads and inter-connections
between pieces of equipment) are properly made and
in accordance with the manufacturers’ instructions.
Switch off and withdraw the mains plug before making
or changing connections.
DO
consult your dealer if you are ever in doubt about
the installation, operation or safety of your equipment.
DO
be careful with glass panels or doors on
equipment.
DO NOT
obstruct the ventilation openings of the
equipment with items such as newspapers, tablecloths,
curtains, etc. Overheating will cause damage and
shorten the life of the equipment.
DO NOT
allow electrical equipment to be exposed to
dripping or splashing or objects filled with liquids, such
as vases, to be placed on the equipment.
DO NOT
place hot objects or naked flame sources,
such as lighted candles or nightlights on, or close to
equipment. High temperatures can melt plastic and
lead to fires.
DO NOT
use makeshift stands and NEVER fix legs with
wood screws. To ensure complete safety, always fit the
manufacturers’ approved stand, bracket or legs with
the fixings provided according to the instructions.
DO NOT
leave equipment switched on when it is
unattended, unless it is specifically stated that it is
designed for unattended operation or has a standby
mode. Switch off by withdrawing the plug, make sure
your family know how to do this. Special arrangements
may need to be made for people with disabilities.
DO NOT
continue to operate the equipment if you are
in any doubt about it working normally, or it is
damaged in any way – switch off, withdraw the mains
plug and consult your dealer.
WARNING
– excessive sound pressure from
earphones or headphones can cause hearing loss.
ABOVE ALL – NEVER let anyone, especially
children, push or hit the screen, push anything
into holes, slots or any other openings in the
case.
NEVER guess or take chances with electrical
equipment of any kind – it is better to be safe
than sorry.
Air Circulation
Heat Damage
Mains Supply
Do
DO NOT REMOVE ANY FIXED COVERS AS THIS WILL
EXPOSE DANGEROUS AND 'LIVE' PARTS.
THE MAINS PLUG IS USED AS A DISCONNECTING
DEVICE AND THEREFORE SHOULD BE READILY
OPERABLE.
Do not
00GB_AVLVRV655P_Euro1.book Page 4 Wednesday, August 26, 2009 5:20 PM
5
INSTALLING YOUR TV
English
Installation and important information
Locate the television away from direct sunlight and strong
lights, soft, indirect lighting is recommended for comfortable
viewing. Use curtains or blinds to prevent direct sunlight
falling on the screen.
Place the TV on a stable, level surface that can support the
weight of the TV.
In order to maintain stability and
prevent it falling over, secure the TV to the level
surface using the strap located under the table top
stand, or to a wall using a sturdy tie to the clip on the
back of the table top stand.
The LCD display panels are manufactured using an
extremely high level of precision technology, however
sometimes some parts of the screen may be missing picture
elements or have luminous spots. This is not a sign of a
malfunction.
Make sure the television is located in a position where it cannot be pushed or hit by objects, as pressure will break
or damage the screen, and that small items cannot be inserted into slots or openings in the case.
Cleaning the screen and cabinet…
Turn off the power, clean the screen and cabinet with a soft, dry cloth. We recommend that you
do not
use any
proprietary polishes or solvents on the screen or cabinet as this may cause damage.
If stationary images generated by 4:3 broadcasts, text services, channel identification logos, computer displays,
video games, on-screen menus, etc. are left on the television screen for any length of time they could become
conspicuous, it is always advisable to reduce both the brightness and contrast settings.
Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the image at the 4:3
outlines, this is not a defect of the LCD TV and is not covered under the manufacturers warranty. Regular use of
other size modes (eg: Superlive) and varying the “side panel” brightness (if available on the model) will prevent
permanent retention.
Where to install
Please take note
EXCLUSION CLAUSE
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i) fire;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damage caused to the product whilst in the possession of a third party;
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the owner’s
manual;
viii) any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with
associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not limited
to the following, loss of profit, interruption of business, the loss of recorded data whether caused during normal operation or
misuse of the product.
NOTE
: A Toshiba wall bracket or stand, where available, must be used.
Side View Top View
Stand clip
Fixing strap
‘P’ Clip
Sturdy tie
(as short as possible)
Fixing strap
00GB_AVLVRV655P_Euro1.book Page 5 Wednesday, August 26, 2009 5:20 PM
6
INSTALLING YOUR TV
English
The remote control
For RV6**P Series
Simple at-a-glance reference of your remote
control.
1
For On/Standby mode (T/D)*
2
To select device mode (T/D)
•
REGZA-LINK
is not used for this model.
3
Number buttons (T/D)
4
To select external input sources (T)
To select line input (D)
5
To alter the TV volume
6
To mute the TV sound
7
To change programme positions (T)
To change text pages (T)
8
To access Quick Menu (T)
9
To exit Menus (T)
10
When using menus, the arrows move the cursor on the
screen up, down, left or right. Press
Q
to confirm your
selection (T/D)
11
To display on-screen information (T/D)
To access index page in Text mode (T)
12
To return to previous Menu (T/D)
13
Colour buttons
Text control buttons (T)
TOP
To access Top Menu (D)
DVD
DVD Menus (D)
•
ROOT
and
CONTENTS
are not used for this model.
14
SUBTITLE
TEXT Subtitle pages if available (T)
SET UP
To access Setup menu (D)
15
s
Stereo/bilingual transmissions (T)
AUDIO
To change Audio setting (D)
16
Widescreen viewing
17
To call up text services (T)
18
When in TV mode:
MENU
On-screen Menus
r
Picture still
D
Time display
When in Text mode:
A
To reveal concealed text
B
To hold a wanted page
C
To enlarge text display size
D
To select a page whilst viewing a normal
picture
When in DVD mode:
press
V
to EJECT
press
v
to STOP
press
c
to PLAY
press
W
/
w
to PAUSE/STEP
press
Z
to SKIP-REWIND
press
CC
to REWIND
press
cc
to FAST FORWARD
press
z
to SKIP-FORWARD
•
ATV/DTV
and
LIST
are not used for this model.
* T=TV mode, D=DVD mode
** These buttons cannot be used.
1
6
8
7
9
10
12
16
1
7
18
4
2
3
**
5
**
11
13
15
14
00GB_AVLVRV655P_Euro1.book Page 6 Wednesday, August 26, 2009 5:20 PM
7
INSTALLING YOUR TV
English
The remote control
For AV6**P and LV6**P Series
Simple at-a-glance reference of your remote
control.
1
For On/Standby mode
2
To select external input sources
3
Picture still
4
To call up text services
5
Stereo/bilingual transmissions
6
TEXT Subtitle pages if available
7
Number buttons
8
In TV mode: To display on-screen information
In Text mode: To access index page in Text mode
9
To alter the TV volume
10
To mute the TV sound
11
In TV mode: To change programme positions
In Text mode: To change text pages
12
To access Quick Menu (T)
13
To exit menus
14
When using menus, the arrows move the cursor on the
screen up, down, left or right. Press
Q
to confirm your
selection
15
To display the on-screen menu
16
To return to the previous menu
17
Text control buttons
18
When in Text mode:
A
To reveal concealed text
B
To hold a wanted page
C
To enlarge text display size
D
To select a page whilst viewing a normal
picture
When in TV mode:
D
Time display
* These buttons cannot be used.
Remove the back cover to reveal the battery compartment and
make sure the batteries are inserted the proper way. Suitable
battery types for this remote are AAA, IEC R03 1.5V.
Do not combine a used, old battery with a new one or mix
battery types. Remove dead batteries immediately to prevent
acid from leaking into the battery compartment. Dispose of
them in accordance with instructions on page 36 of this
manual.
Warning:
batteries must not be exposed to excessive
heat such as sunshine, fire or the like.
The performance of the remote control will deteriorate beyond
a distance of five metres or outside an angle of 30 degrees
from the centre of the television. If the operating range
becomes reduced, the batteries may need replacing.
1
5
6
*
8
11
12
13
16
18
1
7
2
3
4
7
*
10
9
*
14
15
Inserting batteries and effective range of
the remote
CT-90327 CT-90326
00GB_AVLVRV655P_Euro1.book Page 7 Wednesday, August 26, 2009 5:20 PM
8
English
CONNECTING YOUR TV
Connecting external equipment
Before connecting any external equipment, turn off all main power switches. If there is no switch
remove the mains plug from the wall socket.
Aerial cables:
- - - - - - - - - - - - - - - - - - - - - -
Connect the aerial to the socket on the rear of the television.
If you use a decoder* and/or a media recorder it is essential
that the aerial cable is connected through the decoder and/or
through the media recorder to the television.
SCART leads:
. . . . . . . . . . . . . . . . . . . . . . . . . .
Connect the media recorder
IN
/
OUT
socket to the television.
Connect the decoder
TV
socket to the television. Connect the
media recorder
SAT
socket to the decoder
MEDIA REC
. socket.
Before running
Auto tuning
, put your decoder and media
recorder to
Standby
.
The phono sockets alongside the COMPONENT VIDEO INPUT
sockets will accept L and R audio signals.
HDMI™ (High-Definition Multimedia Interface) is for use with
a DVD decoder or electrical equipment with digital audio and
video output.
For acceptable video or PC signal formats through the HDMI
terminals, see page 38.
NOTE:
• The SCART socket does not output video/audio signals in
Photo Viewer mode.
• Although this television is able to connect to HDMI
equipment it is possible that some equipment may not
operate correctly.
A wide variety of external equipment can be connected
to the back of the television; therefore, the relevant
owners manuals for
all
additional equipment must be
referred to for exact instructions.
We recommend
SCART 1
for a decoder and
SCART 2
for a
media recorder.
If the television automatically switches over to monitor external
equipment, return to normal television by pressing the desired
programme position button. To recall external equipment,
press
o
to select between
EXT1
,
EXT2
,
EXT3
,
EXT4
,
HDMI1
,
HDMI2
,
HDMI3
or
PC
.
COMPONENT VIDEO INPUT (EXT3)
HDMI™ INPUT SOCKETS
SCART 2 (EXT2)
FIXING STRAP
SCART 1 (EXT1)
decoder*
media recorder
*a decoder could
be Digital Satellite or
any other compatible
decoder.
POWER switch
(LV6**P and RV6**P
Series only)
Illustration represents 40LV655P.
Antenna/Cable
HDMI, the HDMI logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing, LLC.
00GB_AVLVRV655P_Euro1.book Page 8 Wednesday, August 26, 2009 5:20 PM
9
CONNECTING YOUR TV
English
Connecting an HDMI™ or DVI
device to the HDMI input
The HDMI input on your television receives digital
audio and uncompressed digital video from an
HDMI source device, or uncompressed digital video
from a DVI (Digital Visual Interface) source device.
This input is designed to accept HDCP (High-Bandwidth
Digital-Content Protection) programme material in digital
form from EIA/CEA-861-D–compliant
[1]
consumer electronic
devices (such as a set-top box or DVD player with HDMI or DVI
output). For acceptable video signal formats, see page 38.
NOTE:
Supported Audio format: Linear PCM, sampling rate
32/44.1/48kHz.
Connect an HDMI cable (type A connector) to the HDMI
terminal.
For proper operation, it is recommended that you use an HDMI
cable with the HDMI Logo ( ).
• If your HDMI connection is capable of 1080p and/or your
television is capable of refresh rates greater than 50Hz, you
will need a Category 2 cable. Conventional HDMI/DVI cable
may not work properly with this mode.
• HDMI cable transfers both video and audio. Separate
analogue audio cables are not required (see illustration).
• See “HDMI1 Audio” on page 31.
The HDMI 3 terminal is located on the side of the television.
To view the HDMI device video, press the
o
button to select
HDMI1
,
HDMI2
or
HDMI3
mode.
Connect an HDMI-to-DVI adapter cable (HDMI type A
connector) to the HDMI 1 terminal and audio cables to the PC/
HDMI1 (AUDIO) socket (see illustration).
• The recommended HDMI-to-DVI adapter cable length is 2m
(6.6 ft).
• An HDMI-to-DVI adapter cable transfers video only.
Separate analogue audio cables are required.
• See “HDMI1 Audio” on page 31.
NOTE:
To ensure that the HDMI or DVI device is reset properly, it is
recommended that you follow these procedures:
• When turning on your electronic components, turn on the
television first, and then the HDMI or DVI device.
• When turning off your electronic components, turn off the
HDMI or DVI device first, and then the television.
To connect an HDMI device
HDMI
OUT
VIDEO AUDIO
LR
R
L
OUT
IN
HDMI cable
HDMI device
To connect a DVI device
DVI/HDCP
OUT
VIDEO AUDIO
LR
R
L
OUT
IN
HDMI-to- DVI
adapter Cable
Audio cable for HDMI to
television connection
(not supplied)
DVI device
[1] EIA/CEA-861-D compliance covers the transmission of uncompressed
digital video with high-bandwidth digital content protection, which is
being standardized for reception of high-definition video signals. Because
this is an evolving technology, it is possible that some devices may not
operate properly with the television.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
00GB_AVLVRV655P_Euro1.book Page 9 Wednesday, August 26, 2009 5:20 PM
10
CONNECTING YOUR TV
English
Connecting a computer
With either an RGB/PC or an HDMI connection, you
can watch your computer’s display on the television
and hear the sound from the televisions speakers.
When connecting a PC to the RGB/PC terminal on the
television, use an analogue RGB (15-pin) computer cable and
a PC audio cable for the PC/HDMI1 (AUDIO) socket. Select
PC
from the
PC/HDMI1 audio
options in the
AV connection
menu located in the
SET UP
menu.
To use a PC, set the monitor output resolution on the PC before
connecting it to the television. For acceptable PC signal
formats, see page 37.
To display the optimum picture, use the PC setting feature (see
page 29).
NOTE:
• The PC audio input terminal on the television is shared with
the HDMI 1 analogue audio input terminal (see page 30).
• Some PC models cannot be connected to this television.
• An adapter is not needed for computers with a compatible
mini D-sub15-pin terminal.
• Depending on the DVD’s title and the specifications of the PC
on which you are playing the DVD-Video, some scenes may
be skipped or you may not be able to pause during multi-
angle scenes.
• A band may appear at the edges of the screen or parts of the
picture may be obscured. This is due to scaling of the picture
by the set, it is not a malfunction.
• When PC input mode is selected some of the television’s
features will be unavailable e.g.
Manual Setting
in the
SET UP
menu,
Colour
,
Tint
,
Sharpness
and
Black/White
Level
in the
PICTURE
menu.
• If connecting a certain PC model with a unique PC signal, the
PC signal may not be detected correctly.
When connecting a PC to the HDMI terminal on the television,
use an HDMI-to-DVI adapter cable and an analogue audio
cable.
If connecting a PC with an HDMI terminal, use an HDMI cable
(type A connector). A separate analogue cable is not necessary
(see page 9).
For acceptable PC and video signal formats, see page 38.
NOTE:
• The edges of the images may be hidden.
• If connecting a certain PC model with a unique PC signal, the
PC signal may not be detected correctly.
To connect a PC to the RGB/PC terminal
the back of your television
Computer
Audio cable for PC to
television connection
(not supplied)
Conversion
adaptor if required
(not supplied)
Mini D-sub
15 pin connector
RGB PC cable
(not supplied)
To connect a PC to the HDMI terminal
the back of your television
Computer
Audio cable
for PC to
television
connection
(not supplied)
HDMI-to-DVI
adapter cable
00GB_AVLVRV655P_Euro1.book Page 10 Wednesday, August 26, 2009 5:20 PM
11
CONNECTING YOUR TV
English
Controls and input connections
A wide variety of external equipment can be connected to the input sockets on the side of the television.
Whilst all the necessary adjustments and controls for the television are made using the remote control, the
buttons on the television may be used for some functions
.
If the RED LED is unlit, check that the mains plug is connected
to the power supply. Then press the
!
(POWER) button on
the left side of the television to switch the television on*. If the
picture does not appear, press
1
on the remote control, it may
take a few moments. The GREEN LED will be lit.
To put the television into Standby, press
1
on the remote
control. To view the television, press
1
again. The picture may
take a few seconds to appear.
* LV6**P and RV6**P Series only
Press
MENU
on the remote control to see the menus.
The menu appears as a list of five topics. As each symbol is
selected by pressing
C
or
c
on the navigation ring on the
remote control, its respective options will appear below.
To use the options, press
B
and
b
on the remote control to
move up and down through them and
Q
, and then, press
C
or
c
to select the required choice. Follow the on-screen
instructions. The functions of each menu are described in
detail throughout the manual.
To alter the volume press –
2
+.
To alter the programme position press
b
p
B
.
Press
MENU
and
I
,
i
,
U
or
u
to control the sound and picture
options.
Press
MENU
to finish.
To select an external input, press
o
until the appropriate
input source is selected as described on page 30.
Please always refer to the owner’s manual of the equipment to
be connected for full details.
NOTE:
Interactive video games that involve shooting a "gun"
type of joystick at an on-screen target may not work with this
TV.
Standby
RED LED – Standby
GREEN LED – Power on
POWER switch
(LV6**P and
RV6**P Series only)
USB port
To access
photo files
HDMI3 INPUT
INPUT 4
(EXT4)
GREEN LED – On Timer set
Illustration represents 40LV655P.
Switching on
Using the remote control
Using the controls and connections
00GB_AVLVRV655P_Euro1.book Page 11 Wednesday, August 26, 2009 5:20 PM
12
English
SETTING UP YOUR TV
Startup Application
Before switching on the television, put your decoder
and media recorder, if applicable, to
Standby
. To
set up the television, use the buttons on the remote
control as detailed on page 6 (RV6**P Series) or
page 7 (LV6**P and AV6**P Series).
a
Press the
1
button. The
Quick Setup
screen will
appear. This screen will appear the first time that the
television is switched on and each time
Reset TV
is
selected.
b
Highlight
Language
and press
C
or
c
to select the
menu language.
c
Press
b
to highlight
Country
and
C
or
c
to select.
d
Press
Q
, the
Location
screen will appear.
e
Press
C
or
c
to select
Home
or
Store
. For normal
home use, select
Home
.
f
Press
Q
, the
Auto tuning
start up screen will appear.
g
Press
Q
to start
Auto tuning
.
The search will begin for all available stations. The
slide bar will move along the line as the search
progresses.
You must allow the television to complete the
search.
When the search is complete the television will
automatically select position one. Confirm the result
on the
Manual tuning
screen.
h
Press
EXIT
.
You can also tune in the stations manually using the
Manual
tuning
. For details, see page 13.
Quick Setup
Language English
Country Others
Quick Setup
Home
To use the TV for displaying
in a store showroom,
please select [Store]. [Home]
mode is recommended for
normal use.
Location
Previous settings will be lost!
Press EXIT for no change.
Press OK to start Auto tune.
Auto tuning
PLEASE NOTE
The
Reset TV
menu can also be accessed at any time from
the
SET UP
menu.
Auto tuning
Progress
19%
Found
Channel: C09 Station:
3
Manual tuning
Pos. Station
1
2
3
4
5
6
7
8
C12
C31
C43
C04
C05
C07
C09
C23
ABC2
ABC3
C
–
04
C
–
05
C
–
07
C
–
09
C
–
23
ABC1
Channel
00GB_AVLVRV655P_Euro1.book Page 12 Wednesday, August 26, 2009 5:20 PM
13
SETTING UP YOUR TV
English
Manual Tuning
The television can be tuned-in manually using
Manual
tuning
. For example: if the television cannot be connected to
a media recorder/decoder with a SCART lead or when you
want to tune-in a station on another
System
.
Use
C
and
c
to move across the screen and select any of the
Manual tuning options. Then use
B
or
b
to adjust the settings.
1
Position:
The number to be pressed on the remote control to tune
the channel.
2
System:
Specific to certain areas.
3
Colour system:
Factory set to Auto, should only be changed if problems
are experienced, i.e. NTSC input from external source.
4
Skip:
8
means nothing has been saved or the facility to skip
the channel is ON. See page 14.
5
Signal Class:
The channel classification.
6
Channel:
The channel classification and the channel number on
which a station is being broadcast.
7
Search:
Search up and down for a signal.
8
Manual fine tuning:
Only used if interference/weak signal is experienced. See
page 34.
9
Station:
Station identification. Use the
B
or
b
and
C
or
c
buttons
to enter up to seven characters.
To allocate a position on the television for a decoder and
media recorder: turn the decoder on, insert a pre-recorded
film in the media recorder and press PLAY, then manually
tune.
a
Press
MENU
and using
C
or
c
select the
SET UP
menu. With
b
highlight
Manual tuning
and press
Q
to select.
b
Use
B
or
b
to highlight the position required
e.g.
we
suggest
Pos. 0
for a media recorder.
c
Press
Q
to select. If the channel is set to skip,
Skip
must be removed before storing. See page 14.
d
Press
c
to select
System
and use
B
or
b
to change if
required.
e
Then press
c
to select
Search
.
f
Press
B
or
b
to begin the search. The search symbol
will flash.
Tuning
Different
Channel
numbers may be displayed.
00GB_AVLVRV655P_Euro1.book Page 13 Wednesday, August 26, 2009 5:20 PM
14
SETTING UP YOUR TV
English
g
Each signal will show on the television, if it is not your
media recorder, press
B
or
b
again to restart the
search.
h
When your media recorder signal is found, press
c
to
move along to
Station
. With
B
,
b
,
C
and
c
put in the
required characters,
e.g.
VCR
.
i
Press
Q
to save.
j
Repeat for each
Position
you want to tune or, press
MENU
to return to the list of channels and select the
next number to tune.
k
Press
EXIT
when you have finished.
l
To name external equipment,
e.g.
DVD on EXT2, press
o
to select
o
2, then select
Manual setting
from the
SET UP
menu.
m
Press
c
to select
Label
then using
B
,
b
,
C
and
c
put
in the required characters.
To prevent certain channels from being viewed, positions can be
skipped. The remote control must be removed as the channels
will still be available using the number buttons. Channels can
then be watched as normal using the controls on the television,
but the television will not show the skipped channel positions.
a
Select
Manual tuning
from the
SET UP
menu.
b
Use
B
or
b
to highlight the position to be skipped and
press
Q
to select.
c
Press
c
to select
Skip
.
d
Use
B
or
b
to turn
Skip
on.
Press
Q
.
8
on the screen indicates a skipped position.
e
Press
MENU
and repeat from
Step 2
or press
EXIT
.
Each position has to be
individually
selected. To turn
Skip
off, repeat the procedure for each position.
Skipped positions
cannot
be selected by
P
U
and
P
u
or by the
controls on the television, but
can
still be accessed by the
number buttons on the remote control.
PLEASE NOTE
This television has direct channel entry if the channel
numbers are known.
Select the
Manual tuning
screen in
Step 3
. Enter the
Position number
, the
System
, then
C
for standard
(terrestrial) channels or
S
for cable channels and the
Channel
number. Press
Q
to save.
Skip
00GB_AVLVRV655P_Euro1.book Page 14 Wednesday, August 26, 2009 5:20 PM
15
SETTING UP YOUR TV
English
Channels may be moved and saved to the position of your
choice.
a
Select
Manual tuning
from the
SET UP
menu.
b
With the list of channels now showing use
B
or
b
to
highlight the channel you want to
move
and press
c
.
The selected channel will be moved to the right of the
screen.
c
Use
B
or
b
to move through the list to your
preferred
position. As you do so the other channels will move to
make room.
d
Press
C
to save your move.
Repeat as necessary, then press
EXIT
.
NOTE:
As new services are broadcast it will be necessary to re-
tune the television in order to view them.
Auto tuning
will completely re-tune the television and can be
used to update the channel list.
It is recommended that Auto tuning is run periodically to
ensure that all new services are added
. All current channels
and settings will be lost.
a
Press
MENU
and use
C
or
c
to select
SET UP
menu.
Use
b
to highlight
Auto tuning
. Press
Q
.
b
A screen will appear warning that previous
programmes and settings will be deleted.
Press
Q
to continue with the
Auto tuning
.
The television will start to search for all available
services.
You must allow the television to complete the
search.
When the search is complete the television will
automatically select position one. Confirm the result
on the
Manual tuning
screen.
c
Press
EXIT
.
Other feature
You can select either
Home
or
Store
mode.
Home
is
recommended for normal home use. Select
Store
when using
a television for displaying in a shop, etc.
a
Select
Location
from the
SET UP
menu.
b
Press
C
or
c
to select
Home
or
Store
.
Sorting Positions
Auto Tuning
Location Setting
00GB_AVLVRV655P_Euro1.book Page 15 Wednesday, August 26, 2009 5:20 PM
16
English
CONTROLS AND FEATURES
General controls
To select a position, use the numbered buttons on the remote
control.
Positions can also be selected using
P
U
and
P
u
.
To display on-screen information
i.e.
position, input mode or
stereo/mono signal, press . Press again to cancel.
You can select a channel from
Channel List
.
a
Press
QUICK
to open the
Quick Menu
.
b
Press
B
or
b
to select
Channel List
and press
Q
.
c
Press
B
or
b
to highlight a channel and press
Q
to
watch.
Time display facility allows the current (text service) time to be
seen on the television screen.
Press
D
whilst watching a normal television broadcast to
see a time display from the broadcaster. It will remain on
screen for about 5 seconds.
NOTE:
This display may not be available in some cases.
If stereo or dual language broadcasts are transmitted, the word
Stereo or Dual will appear on the screen each time positions are
changed, disappearing after a few seconds. If the broadcast is
not in stereo, the word Mono will appear.
Stereo…
Press
s
to select
Stereo
or
Mono
.
Bilingual…
Bilingual transmissions are rare. If they are
transmitted, the word
Dual
will be displayed. Choose the
required programme number and if the word
Dual
appears
press
s
to select
Dual 1
,
Dual 2
or
Mono
.
Quick Menu
helps you access some options quickly, such as
Picture Mode, Picture Size, Sleep timer
etc.
Press
QUICK
to display the
Quick Menu
and use
B
or
b
to
select the option.
NOTE: Quick Menu
items are different depending on the
current mode.
Selecting Positions
Channel List
Time Display
Stereo and Bilingual Transmissions
Quick Menu
Mode Quick menu item Description
When viewing a
TV programme or
pictures from the
external input
Picture Mode See page 20.
Picture Size See page 18.
Channel List See left
column.
Sleep timer See page 27.
Media Player See page 25.
Bass Boost See page 17.
When using
Media Player
Interval Time See page 26.
Repeat See page 26.
00GB_AVLVRV655P_Euro1.book Page 16 Wednesday, August 26, 2009 5:20 PM
17
CONTROLS AND FEATURES
English
Sound controls
Volume
Press
Y
or
y
to adjust the volume.
Sound Mute
Press once to turn the sound off and again to cancel.
If a programme or film is being broadcast with a soundtrack in
more than one language, the
Dual
feature allows selection
between them.
a
Press
MENU
and
C
or
c
to select
SOUND
.
b
Use
b
to highlight
Dual
then press
C
or
c
to choose
between
Dual 1
or
Dual 2
.
a
Select the
SOUND
menu.
b
Press
b
to highlight
Bass
,
Treble
or
Balance
and
C
or
c
to change the setting.
Voice Enhancement
makes vocal sound clearer; for example,
singers or announcers.
Bass Boost
enhances the depth of the sound.
a
In the
SOUND
menu, press
b
to highlight
Advanced
Sound Settings
then press
Q
.
b
Press
b
to highlight
Voice Enhancement
then press
C
or
c
to select
On
or
Off
.
c
Press
b
to highlight
Bass Boost
and using
C
or
c
to
select
On
or
Off
.
The
Stable sound
feature limits high volume levels on the TV
speakers preventing the extreme changes in volume that can
occur when channels are changed or a programme switches to
a commercial.
a
Select the
SOUND
menu.
b
Use
b
to highlight
Stable sound
then press
C
or
c
to select
On
or
Off
.
Volume Controls and Mute Sound
Dual
Bass, Treble and Balance
Advanced Sound Settings
Stable Sound
®
00GB_AVLVRV655P_Euro1.book Page 17 Wednesday, August 26, 2009 5:20 PM
18
CONTROLS AND FEATURES
English
Widescreen viewing
Depending on the type of broadcast being
transmitted, programmes can be viewed in a
number of formats.
SUBTITLE
SUBTITLE
SUPER LIVE
This setting will enlarge a 4:3 image
to fit the screen by stretching the
image horizontally and vertically,
holding better proportions at the
centre of the image. Some distortion
may occur.
When subtitles are included on a
letterbox format broadcast, this
setting will raise the picture to ensure
that all the text is displayed.
CINEMA
When watching ‘all sides panel
format’ films/video tapes, this setting
will eliminate or reduce the black
bars at all sides of the screen by
zooming in and selecting the image
without distortion.
WIDE
Use this setting when watching a
widescreen DVD, widescreen video
tape or a 16:9 broadcast (when
available). Due to the range of
widescreen formats (16:9, 14:9,
20:9 etc.) black bars may be visible
on the top and bottom of the screen.
4:3
Use this setting to view a true 4:3
broadcast.
14:9
Use this setting when watching a
14:9 broadcast.
00GB_AVLVRV655P_Euro1.book Page 18 Wednesday, August 26, 2009 5:20 PM
19
CONTROLS AND FEATURES
English
Press
QUICK
and highlight
Picture Size
, then press
Q
to display the list of available widescreen formats.
Use
B
and
b
to highlight the required format and
Q
to select.
• When a format is not available, it will be grayed out.
Using the special functions to change the size of the displayed image (i.e. changing the height/width ratio) for the purposes of public
display or commercial gain may infringe on copyright laws.
Dot by Dot
PC NORMAL
NATIVE
This setting will show the picture
without over scan, i.e. WYSIWYG.
This option is only available when
watching PC signal source via HDMI
or PC terminal.
PC WIDE
This setting will show the picture
without over scan and side panel.
This option is only available when
watching PC signal source via HDMI
or PC terminal.
“Dot by Dot”
is a non-scaling display.
Depending on the input signal format,
the picture is displayed with side
panels and/or bars at the top and
bottom (i.e. VGA input source).
This setting will show the picture
without over scan, i.e. WYSIWYG.
This option is only available in the
HDMI input mode.
AV format PC format
00GB_AVLVRV655P_Euro1.book Page 19 Wednesday, August 26, 2009 5:20 PM
20
CONTROLS AND FEATURES
English
Picture controls
PLEASE NOTE: features not available will be greyed
out
.
The picture position may be adjusted to suit personal preference
and can be particularly useful for external inputs.
a
In the
SET UP
menu press
b
until
Picture position
is
highlighted.
b
Press
Q
to view the options available for the picture
format that has been selected.
c
Press
B
and
b
to select an option, then
C
or
c
to
adjust the settings.
The options alter depending on currently selected
widescreen format and the input signal.
In
Cinema
:
To return to the original factory settings select
Reset
in the
Picture position
menu and press
Q
.
This television offers the choice of personalising the picture
style.
AutoView
*,
Dynamic
,
Standard
,
Mild
,
Movie
,
Game
and
PC
are preset options and affect many features/settings within
the television.
NOTE:
• Because the
AutoView
mode automatically adjusts picture
settings based on ambient light conditions and input signal
content, the
Auto Brightness Sensor
menu is greyed out
when it is selected*.
•
Game
mode is available in external input mode (other than
aerial input). When you select
Game
mode, suitable
widescreen formats will be selected.
•
PC
mode is available in RGB/PC input mode or HDMI input
mode.
a
In the
PITCURE
menu press
b
to select
Picture
settings
, then press
Q
.
b
Using
b
to highlight
Picture Mode
, then press
C
or
c
to select your preference from
AutoView
*,
Dynamic
,
Standard
,
Mild
,
Movie
,
Game
or
PC
.
NOTE:
The picture mode you select affects the current input
only. You can select a different picture mode for each input.
Picture Position
Picture Mode
* LV6**P and RV6**P Series only
00GB_AVLVRV655P_Euro1.book Page 20 Wednesday, August 26, 2009 5:20 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
Toshiba 40LV655P Owner's manual
- Category
- LCD TVs
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Toshiba 46WM48 Owner's manual
-
-
-
-
-
-
Toshiba 32XV636 Owner's manual
-
Toshiba 32AV554 User manual
-
-
Other documents
-
Phanteks Evolv Sound Mini Speakers Owner's manual
-
Sanyo CE32WN3-B User manual
-
SRS Labs WL66 User manual
-
Cables Direct NLUSB2-224WT Datasheet
-
Conceptronic CLHDMIMNHDMI Datasheet
-
Sony KD-32NS100B Owner's manual
-
Dynex DX-15E220A12 User manual
-
-
Aiwa KD-32NX100U User manual
-
