vii_ English
IMPORTANT NOTE
• Handle the liquid crystal display (LCD) with care:
- The LCD is a very delicate display device: Do not press its
surface with force, hit it or prick it with a sharp object.
- If you push the LCD surface, unevenness in display may occur. If
unevenness does not disappear, turn the camcorder off, wait for
a few moments, and then turn it on again.
- Do not place the camcorder with the open LCD screen down.
- Close the LCD screen when not using the camcorder.
Liquid crystal display :
- The LCD screen the product of highly precise technology. Among
the total number of pixels (approx. 230,000 pixels for LCD
screen), 0.01% or less pixels may be missing (black dots) or
may remain lit as colored dots (red, blue, green). This shows the
limitations of the current technology, and does not indicate a fault
that will interfere with recording.
- The LCD screen will be slightly dimmer than usual when the
camcorder is at low temperature, as in cold areas, or immediately
after power is turned on. Normal brightness will be restored when
the temperature inside the camcorder rises. This has no effect
on the images in the storage media, so there is no cause for
concern.
• Hold the HD camcorder correctly:
Do not hold the HD camcorder by the LCD screen when lifting it: the
LCD screen could detach and the HD camcorder may fall.
• Do not subject the HD camcorder to impact:
-
This HD camcorder is a precision machine. Take great care
that you do not strike it against a hard object or let it fall.
- Do not use the HD camcorder on a tripod (not supplied) in a
place where it is subject to severe vibrations or impact.
• No sand or dust!
Fine sand or dust entering the HD camcorder or AC power adaptor
could cause malfunctions or defects.
• No water or oil!
Water or oil entering the HD camcorder or AC power adaptor could
cause electric shock, malfunctions or defects.
• Heat on surface of product:
The surface of the HD camcorder will be slightly warm when in use,
but this does not indicate a fault.
precautions when using
臺灣 _
vii
重要注意事項
•
細心處理液晶顯示器 (LCD):
- LCD 是非常精密的顯示裝置:切勿用力壓其表面,或使用尖銳的
物件擊打或刺戳。
- 如果您按壓 LCD 表面,可能會在顯示時出現不平現象。如果不平
現象不消失,請關閉攝錄放影機,等待片刻後再次開啟。
- 切勿使開啟的 LCD 螢幕向下放置攝錄放影機。
- 在不使用攝錄放影機時關閉 LCD 顯示器。
液晶顯示:
- LCD 螢幕是高精密技術的產品。在總像素(LCD 螢幕的將近
230,000 像素)中,0.01% 或更少的像素可能損失(黑點),或可
能以彩色(紅、藍和綠色)的點亮起。這表明了當前技術的局限
性,但不表示是影響錄製的故障。
- 當攝錄放影機處於低溫時(如在較冷區域),LCD 螢幕將比往常
稍暗,或在電源開啟後會立即變暗。當攝錄放影機內部的溫度上
升時,會恢復到原來的亮度。這對儲存媒體中的影像沒有什么影
響,因此無需顧慮。
•
正確把持 HD 攝錄放影機:
在舉起時,切勿握住 LCD 螢幕旁邊的 HD 攝錄放影機:LCD 螢幕可能
會分離,HD 攝錄放影機可能會摔落。
•
切勿撞擊 HD 攝錄放影機:
- 此 HD 攝錄放影機是精密器械。要特別小心,不要讓其撞擊硬物
或摔落。
- 切勿在嚴重振動或撞擊的地方將 HD 攝錄放影機放在三角架
(未提供)上使用。
•
要避免沙塵!
細沙或灰塵進入 HD 攝錄放影機或交流電源適配器會引起故障。
•
要避免水或油!
水或油進入 HD 攝錄放影機或交流電源適配器會引起觸電或故障。
•
產品表面變熱:
在使用時,HD 攝錄放影機表面會輕微變熱,但這並不表示有故障。
使用時的注意事項