Nokia AUTO NAVIGATION 500 User manual

Nokia 500 Auto Navigation

User Guide

9206144

Issue 1

DECLARATION OF CONFORMITY

Hereby, NOKIA CORPORATION declares that this PD-14 product is in compliance

with the essential requirements and other relevant provisions of Directive 1999/

5/EC.

The product is in conformity with the limits defined in Directive 2004/104/EC

(amending Directive 72/245/EEC), Annex I, paragraph 6.5, 6.6, 6.8 and 6.9.

A copy of the Declaration of Conformity can be found at http://www.nokia.com/

phones/declaration_of_conformity/.

At the time of production of this document, the FM transmitter part of this

product is intended for use in the following countries: Belgium, Czech Republic,

Denmark, Estonia, Finland, Germany, Iceland, Liechtenstein, Luxembourg,

Norway, Portugal, Spain, Switzerland, Sweden, Turkey, United Kingdom. For the

latest information, refer to http://www.nokia.com.

Nokia and Nokia Connecting People are registered trademarks of Nokia Corporation. Other

product and company names mentioned herein may be trademarks or tradenames of their

respective owners.

reserved

.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

Reproduction, transfer, distribution, or storage of part or all of the contents in this document

in any form without the prior written permission of Nokia is prohibited.

This product is licensed under the MPEG-4 Visual Patent Portfolio License (i) for personal and

noncommercial use in connection with information which has been encoded in compliance

with the MPEG-4 Visual Standard by a consumer engaged in a personal and noncommercial

activity and (ii) for use in connection with MPEG-4 video provided by a licensed video

provider. No license is granted or shall be implied for any other use. Additional information,

including that related to promotional, internal, and commercial uses, may be obtained from

MPEG LA, LLC. See <http://www.mpegla.com>.

Nokia operates a policy of ongoing development. Nokia reserves the right to make changes

and improvements to any of the products described in this document without prior notice.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES

SHALL NOKIA OR ANY OF ITS LICENSORS BE RESPONSIBLE FOR ANY LOSS OF DATA OR

INCOME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES

HOWSOEVER CAUSED.

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY

APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR

CONTENTS OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR

WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE.

The availability of particular products and applications and services for these products may

vary by region. Please check with your Nokia dealer for details, and availability of language

options.

This device complies with Directive 2002/95/EC on the restriction of the use of certain

hazardous substances in electrical and electronic equipment.

Export Controls

This device may contain commodities, technology or software subject to export laws and

regulations from the US and other countries. Diversion contrary to law is prohibited.

9206144 / Issue 1 EN

4

Contents

For your safety.......................... 6

1. Introduction .......................... 7

Bluetooth wireless technology........... 7

Global Positioning System (GPS)....... 7

DVD ............................................................ 8

2. Get started ......................... 10

Keys and parts...................................... 10

Front, right, and top view ............. 10

Back, left, and base view............... 11

Chargers................................................. 11

Charge the battery.............................. 11

First use ................................................. 12

Switch on or off and

standby mode....................................... 13

Switch on or off............................... 13

Standby mode................................... 13

Bluetooth connection

at startup........................................... 14

Set up Bluetooth connection........... 14

Connect manually or

change the connected device ...... 15

Connect automatically................... 15

Delete pairings ................................. 15

Disconnect a device........................ 15

Turn Bluetooth connectivity

on or off ............................................. 15

Install the device in a car ................. 16

General safety instructions........... 16

Attach mobile holder

to mounting device......................... 17

Attach mounting device

to windscreen ................................... 17

Place navigation device

into holder......................................... 18

Set navigation device

to desired position .......................... 18

Memory card ........................................ 18

Insert the card .................................. 19

Copy files to the card ..................... 19

3. Basic operation................... 21

Touch screen ........................................ 21

Open applications

from map screen ................................. 21

Adjust the volume............................... 22

Adjust device settings........................ 22

Audio volume and key tones........ 22

Language............................................ 22

Backlight............................................ 22

Time and date................................... 23

System ................................................ 23

FM transmitter ................................. 24

Reset....................................................... 24

4. Navigator............................ 25

Map......................................................... 25

Tracking mode .................................. 26

Browsing mode ................................ 27

Navigate to a destination................. 28

Navigation screen ........................... 29

Functions available

in navigation screen ....................... 30

Navigate to an address .................. 30

Navigate to a point of interest.... 31

Favourites .......................................... 31

Recent locations .............................. 32

Plan a route .......................................... 33

Traffic information (TMC)................. 34

Navigation settings ............................ 34

General settings............................... 34

Map settings ..................................... 35

Route settings .................................. 35

Volume................................................ 36

5. Call handling ...................... 37

Make a call ........................................... 37

Tap a number using dial pad........ 37

Call a saved contact ....................... 38

Call register....................................... 38

Voice dialling .................................... 38

Speed dialling (Favourites) ........... 39

5

Answer or reject a call ....................... 39

Call waiting........................................ 39

In-call options ...................................... 40

Adjust phone settings ........................ 40

Phone connections .......................... 40

Bluetooth............................................ 41

Contacts download.......................... 41

Sort order of contacts..................... 41

Ringing tone...................................... 41

Ringing volume................................. 41

6. Music player....................... 42

Use FM transmitter

or headphones...................................... 42

FM transmitter.................................. 42

Headphones....................................... 43

Listen to music..................................... 43

Exit to navigation screen .................. 44

7. Video player ........................ 45

Watch video clips ................................ 45

8. Image viewer....................... 47

View images.......................................... 47

9. Battery information ........... 49

Care and maintenance ........... 50

For your safety

6

For your safety

Read these simple guidelines. Not following them may be dangerous or illegal.

Read the complete user guide for further information.

ROAD SAFETY COMES FIRST

Obey all local laws. Always keep your hands free to operate the

vehicle while driving. Your first consideration while driving should

be road safety.

INTERFERENCE

All wireless devices may be susceptible to interference, which could

affect performance.

Introduction

7

1. Introduction

You can use the Nokia 500 Auto Navigation device for GPS navigation in

a car and outdoors. You can also make calls, view photos, watch videos,

and listen to music.

Read this user guide carefully before using the device. Also read the user

guide for your mobile phone. It provides important safety and

maintenance information.

Check www.nokia.com/support or your local Nokia website for the latest

version of the user guide, additional information, software updates, and

services related to your Nokia product.

Your device and its accessories may contain small parts. Keep all

accessories and enhancements out of the reach of small children.

■ Bluetooth wireless technology

Bluetooth wireless technology allows you to connect compatible

devices without cables. A Bluetooth connection does not require that

the two devices be in line of sight, but the devices should be within

10 metres (33 feet) of each other. The connection is subject to

interference from obstructions, such as walls, or other electronic

devices.

The navigation device is compliant with Bluetooth Specification 2.0

supporting the following profiles: Handsfree Profile 1.5 and Phone Book

Access Profile (PBAP) 1.0. Check with the manufacturers of other

devices to determine their compatibility with this navigation device.

■ Global Positioning System (GPS)

The GPS is a worldwide satellite-based radio navigation system. The

internal GPS receiver can calculate the location of the device to an

accuracy of 10 metres. The accuracy depends, for example, on the

number of satellites, the signals of which the GPS module receives. In

optimal conditions, the accuracy may be within a few metres.

Introduction

8

The GPS antenna is located at the top of the navigation device. Some car

windscreens and windows may contain metal, that may block or weaken

the satellite signals.

If you stand still, GPS cannot detect which way you are facing because it

determines your direction on the basis of your movement.

Almost all digital cartography is inaccurate and incomplete to some

extent. Never rely solely on the cartography provided for use with the

GPS application.

The Global Positioning System (GPS) is operated by the government of the United

States, which is solely responsible for its accuracy and maintenance. The

accuracy of location data can be affected by adjustments to GPS satellites made

by the United States government and is subject to change with the United States

Department of Defense civil GPS policy and the Federal Radionavigation Plan.

Accuracy can also be affected by poor satellite geometry. Availability and quality

of GPS signals may be affected by your location, buildings, natural obstacles, and

weather conditions. The GPS receiver should only be used outdoors to allow

reception of GPS signals.

Any GPS should not be used for precise location measurement, and you should

never rely solely on location data from the GPS receiver and cellular radio

networks for positioning or navigation.

■ DVD

The navigation device comes with a DVD. You can do the following:

• Restore data from the DVD to your memory card.

• Copy new content from the DVD to the memory card. The content

can be, for example, maps, points of interest (POI) databases, and

languages.

• Copy content from the DVD to another memory card.

• Read the user guide available on the DVD in several languages.

Before copying data to the memory card, check that the card is not

locked. To copy content from the DVD to the memory card, ensure that

the card is inserted in the navigation device, and connect the device

with the supplied USB cable to your compatible PC. Alternatively, insert

the memory card into the memory card reader on your PC. Insert the

Introduction

9

DVD into the compatible DVD drive on your PC. The setup wizard starts

automatically (if allowed in the settings of the DVD drive) and guides

you through the setup.

If you want to change the contents of the memory card, select all the

maps, POI databases, and languages that you want to add to the card.

When the wizard copies these files to the memory card, the old files of

the same type are deleted from the card.

The Cities folder on the memory card is needed for the use of the

Navigator application. Do not modify or delete it manually. If needed,

you can restore the folder from the DVD using the wizard.

You can only select the device language from the languages that you

have chosen for Navigator. See also “Language,” p. 22.

To copy files to the memory card from a compatible PC, see “Memory

card,” p. 18.

Get started

10

2. Get started

■ Keys and parts

Parts of the device are magnetic. Metallic materials may be attracted to the

device. Do not place credit cards or other magnetic storage media near the

device, because information stored on them may be erased.

Front, right, and top view

1. Cover of connector for an optional external GPS antenna

2. Power key

3. Cover of stereo audio-out connector

4. Indicator light

5. Touch screen

6. Volume down key

7. Menu key

8. Volume up key

9. Memory card with adapter

10.Memory card slot

2 3

10

6

7

8

4

1

9

5

Get started

11

Back, left, and base view

1. Loudspeaker

2. Main power switch

3. Mini USB port/charger connector

4. Reset key

5. Microphone

■ Chargers

This device is intended for use when supplied with power from the DC-1001

charger.

Warning: Use only chargers approved by Nokia for use with this

particular device. The use of any other types may invalidate any

approval or warranty, and may be dangerous.

When you disconnect the power cord of any enhancement, grasp and pull the

plug, not the cord.

■ Charge the battery

Before charging the battery, carefully read “Battery information,” p. 49.

2

4

1

3

5

Get started

12

1. Connect the charger to the mini USB port on the navigation device,

and insert the charger plug into the cigarette lighter socket of your

car.

Power must be supplied by the 12 V car battery. Ensure that the

charger is properly inserted in the cigarette lighter socket and does

not interfere with the normal operation of the car.

In some car models, the cigarette lighter socket is powered by the car

battery even when you remove the ignition key. In those cases, the

car battery might be discharged if the navigation device is left on, or

if the device is turned off but connected to the cigarette lighter

socket for a long time. Contact the vehicle manufacturer for more

information.

The indicator light is orange during charging. If charging does not

start, disconnect the charger, and plug it in again.

2. When the battery is fully charged, the indicator light turns green.

Disconnect the charger from the cigarette lighter socket.

If you use the TMC (traffic message channel) service with the

navigation device, keep the charger connected to the navigation

device as the charger includes the TMC antenna.

When battery power is low, the indicator light is red, the battery icon

shows one bar or no bars, and a text about low battery is displayed.

■ First use

To switch on the navigation device for the first time, slide the main

power switch to the right.

When you are asked to calibrate the screen, tap and briefly press the

displayed crosshair with your finger. Repeat this as the crosshair moves

around the screen. To calibrate the screen later, see “System,” p. 23.

When you are asked to select the language, tap the desired language

and . The language is used for display texts and spoken navigation

instructions.

Carefully read and accept the displayed safety notice, and tap the right

arrow. (To hide this screen in the future, tap the related selection box.)

Get started

13

The Navigator application starts and the map view is displayed. Now you

can start to use the device.

Next, set the time and date. See “Adjust device settings,” p. 22.

To pair and connect the navigation device with a compatible mobile

phone using Bluetooth wireless technology, see steps 2 to 5 in “Set up

Bluetooth connection,” p. 14.

When you are asked to download the contacts from your phone to the

navigation device, tap Yes to start the download. If you select No, you

cannot use the contacts saved in your phone with the navigation device.

In this case, to download the contacts later, press the menu key, and tap

Phone > Contacts > Yes.

■ Switch on or off and standby mode

The navigation device has a main power switch to turn the device on or

off and a power key to set the device into the standby mode.

In daily use, use the standby mode instead of switching the device off.

This way the device starts up faster.

You only need to switch off the device when you do not intend to use it

for a longer time.

Switch on or off

To switch on, slide the main power switch to the right.

To switch off, slide the main power switch to the left.

Standby mode

To save battery power when you are not using the device, set it to the

standby mode. Press and hold the power key for about 3 seconds. The

screen turns off.

To exit the standby mode, press and hold the power key for about 3

seconds.

Get started

14

Bluetooth connection at startup

When you switch on the device or exit the standby mode, you are asked

whether you want to connect the device to the previous mobile phone.

To connect to the previous phone, tap its name. The map screen is

displayed.

To connect to some other device, tap Other. The Phone connections

screen is displayed. Tap the desired device and Connect. To download

the contacts saved in the other device, tap Yes.

To pair with a new device, in Phone connections, tap Pair new, and

proceed as instructed in steps 4 to 5 in “Set up Bluetooth connection,”

p 14.

■ Set up Bluetooth connection

You can connect the navigation device to a compatible mobile phone

using Bluetooth wireless technology.

To pair and connect the navigation device with your device, do as

follows:

1. Switch on the navigation device and your mobile phone.

2. Activate the Bluetooth feature on your phone. See the user guide of

your phone for instructions.

3. On the navigation device, press the menu key, and tap Phone.

If the Bluetooth feature is not active in your phone, you are asked if

you want to activate it. Tap Yes.

4. When the device asks you to start pairing from your phone, set your

phone to search for Bluetooth devices, and select the navigation

device (Nokia PND) from the list of found devices on your phone.

5. Enter the passcode 0000 on your phone to pair and connect the

navigation device to it.

In some phones you may need to make the connection separately

after pairing. See the user guide of your phone for details.

You only need to pair the navigation device with your phone once.

Get started

15

If the navigation device was connected to your phone, the Bluetooth

name of the device is displayed. You can define the Bluetooth name in

your phone. The navigation device is shown in the menu of your phone

where you can view the currently paired Bluetooth devices.

You can pair the navigation device with up to eight mobile phones but

connect it to only one phone at a time.

Connect manually or change the connected device

To connect the navigation device manually to a paired phone or change

the connected phone, press the menu key, and tap Phone > Settings >

Phone connections. Tap the desired device and Connect.

Connect automatically

You can set your paired phone to allow an automatic connection with

the navigation device when the navigation device is switched on. To do

this in Nokia devices, change your paired device settings in the

Bluetooth menu.

Delete pairings

To delete a device from the paired devices list, press the menu key, and

tap Phone > . Tap the desired device and Delete > Yes. To delete all

devices, tap Delete all > Yes.

Disconnect a device

To disconnect a device from the navigation device, press the menu key,

and tap Phone > . Tap the desired device and Disconnect.

Alternatively, you can do one of the following:

• End the connection in the Bluetooth menu of your phone.

• Turn off Bluetooth connectivity in the navigation device.

• Switch off the navigation device.

Turn Bluetooth connectivity on or off

To turn off Bluetooth connectivity when no device is connected to the

navigation device, press the menu key, and tap Phone > Cancel > >

.

Get started

16

To turn off Bluetooth connectivity when a device is connected to the

navigation device, press the menu key, and tap Phone > > > Yes.

To turn on Bluetooth connectivity, press the menu key, and tap Phone >

> > Yes.

■ Install the device in a car

To install the navigation device in a car, attach the HH-12 mounting

device to the CR-91 mobile holder, attach the mounting holder to the

windscreen, and place the navigation device into the mobile holder.

It is advised that you do not leave the mounting device or the mobile

holder visible in the car to prevent theft when you exit the car.

General safety instructions

Obey all local laws. Always keep your hands free to operate the vehicle

while driving. Your first consideration while driving should be road

safety. Only operate the mounting device, mobile holder, or navigation

device if it is safe to do so under all driving conditions.

When you install the mounting device or mobile holder, ensure that they

do not interfere with or hinder the steering or braking systems or other

systems used in the operation of the vehicle (for example, airbags) or

disturb your field of vision while driving.

Check that the deployment of the airbag is not blocked or impaired in

any way.

Ensure that the mounting device or mobile holder is not installed where

you might come in contact with it in the event of an accident or

collision.

Periodically check that the suction cup at the bottom of the mounting

device is firmly attached to the windscreen, especially if the ambient

temperature changes a lot.

Do not leave the product parts inside the vehicle in direct sunlight or in

excessive heat. The product may be damaged if the operating

temperature falls below -25°C (-13°F) or exceeds +55°C (131°F) or if the

Get started

17

storage temperature falls below -40°C (-40°F) or exceeds + 100°C

(212°F).

Attach mobile holder to mounting device

Attach the mobile holder to the mounting device using the supplied

screw (1), and snap the supplied protection plate with the "Nokia" text

over the screw.

Attach mounting device to windscreen

Locate a safe mounting surface on the windscreen, and clean the

surface thoroughly with a glass cleaner and a clean towel. If the

ambient temperature is low, you may need to warm the windscreen to

improve the grip.

Press the suction cup firmly on the windscreen, and carefully push the

locking lever above the cup toward the cup to create a vacuum between

Get started

18

the cup and the windscreen (2). Check that the suction cup is firmly

attached.

If you want to detach the mounting device from the windscreen,

carefully push the locking lever toward the top of the mounting device,

and pull the strap located on the edge of the suction cup.

Place navigation device into holder

To place the navigation device into the mobile holder, insert the catches

at the bottom of the holder into the recesses at the bottom of the device

(3).

Press the navigation device toward the back of the holder so that the

catches on the two arms of the holder click into the corresponding slots

at the sides of the device (4). Ensure that the screen is clearly visible for

the user.

If you want to release the navigation device from the mobile holder,

push the arms of the holder.

Set navigation device to desired position

Do not adjust the mounting device while driving.

To set the navigation device to the desired vertical position, loosen the

two screws at the sides of the mounting device, turn the navigation

device to the desired position, and tighten the screws (5).

To set the navigation device to the desired horizontal position, loosen

the screw below the mounting device, turn the navigation device to the

desired position, and tighten the screw (6).

Ensure that the navigation device is firmly locked into place.

■ Memory card

The device comes with a memory card and an adapter. You can only use

memory cards formatted with the FAT or FAT32 file system with this

device.

The device supports the SDHC (SD High-Capacity) standard that allows

for the use of memory cards of up to 16 gigabytes.

Get started

19

Use only compatible SD cards approved by Nokia for use with this device. Nokia

uses approved industry standards for memory cards, but some brands may not be

fully compatible with this device. Incompatible cards may damage the card and

the device and corrupt data stored on the card.

Insert the card

Slide the memory card into the adapter in the direction marked on the

card so that the label sides of the card and adapter point up.

Insert the memory card into the memory card slot so that the bevelled

corner points to the top of the device. Carefully push the memory card

into the slot until it locks into place.

To remove the memory card, switch off the device, and push the card

until it pops out from the slot.

Important: Do not remove the memory card in the middle of an

operation when the card is being accessed. Removing the card in the

middle of an operation may damage the memory card as well as the

device, and data stored on the card may be corrupted.

Copy files to the card

To play music, view photos, watch videos, or use maps with the

navigation device, you must copy these files to the memory card from a

compatible PC. You can do this while the card is inserted in the

navigation device or the PC. Before copying data to the memory card,

check that the card is not locked.

The Cities folder on the memory card is needed for the use of the

Navigator application. Do not modify or delete it manually. If needed,

you can restore the folder from the supplied DVD.

To copy files to the memory card from the supplied DVD, see “DVD,” p. 8.

To copy files to the memory card from a PC, do either of the following:

• To copy files to the memory card inserted in the navigation device,

first check that the operating system in your PC supports USB mass

storage devices. Such operating systems are, for example, Microsoft

Windows 2000, Windows XP, and Windows Vista.

Get started

20

Plug one end of the supplied DKE-2 USB data cable to the mini USB

port on the device and the other end to a compatible USB port on the

PC.

The operating system detects the navigation device as a mass

storage device, and Mass storage mode is displayed on the

navigation device. Copy the files from the PC to the navigation

device as instructed in the documentation of the operating system.

When the navigation device is connected to the PC with the DKE-2

cable, the battery of the device is charged from the PC.

• To copy files to the memory card inserted in a PC, remove the card

from the navigation device, and insert it into the memory card reader

on your PC. Copy the files as instructed in the documentation of the

PC and its operating system. Remove the card from the PC, and insert

it into the navigation device.

Page is loading ...

Nokia AUTO NAVIGATION 500 User manual

This manual is also suitable for

Nokia AUTO NAVIGATION 500 User manual

Related papers

Other documents