Bimar CALDISSIMO (type S598.EU mod.CH 3000 TURBO) Owner's manual



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

LIBRETTO ISTRUZIONI

NOTICE D'INSTRUCTIONS

INSTRUCTION BOOKLET

BEDIENUNGSANLEITUNG

FOLLETO DE INSTRUCCIONES

Termoconvettore

Thermoconvector

Thermoconvecteur

Thermokonvector

Termoconvector

type S598.EU (mod.CH 3000 TURBO)

1/28

Assembly page 1/28

Page is loading ...



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

DESCRIZIONE DELL’APPARECCHIO

1) Manopola termostato

2) Interruttore 1250W

3) Interruttore 750W

4) Interruttore ventola

USO

Prima di ogni utilizzo verificare che l’apparecchio sia in buono stato, che il cordone elettrico non sia

danneggiato: se il cavo di alimentazione è danneggiato, esso deve sostituito dal costruttore o dal suo

servizio assistenza tecnica o comunque da una persona con qualifica similare, in modo da prevenire

ogni rischio.

Per l’impiego del termoconvettore si operi nel modo seguente:

1) Inserire la spina nella presa nella presa di corrente.

2) Ruotare la manopola termostato (1) in senso orario nella posizione corrispondente alla temperatura

desiderata.

3) Per accendere l’apparecchio, premere l’interruttore (2) per riscaldare 1250W, o l’interruttore (3)

per riscaldare 750W o entrambi per riscaldare a 2000W.

4) Per azionare la ventola (4) premere l’interruttore (4).

5) Il segnalatore luminoso si spegne quando l’apparecchio raggiunge le temperatura impostata.

5/28

Assembly page 5/28

Page is loading ...



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

Please read these instructions carefully before using the appliance, and instruct other persons using it,

too, when necessary. KEEP BOOKLET HANDY FOR FURTHER USE.

If when reading this instructions manual certain parts should remain difficult to understand, or

if there is any confusion, contact the company indicated on the last page before using the

product.

GENERAL ADVISE

• This appliance is destined only to the heating of internal domestic or similar environments and in

compliance with these instructions. It can be considered only a supplementary source of heating

and not as a central heating element.

This appliance is intended to be used in household and similar applications such as:

- staff kitchen in shops, offices and other working environments;

- farm houses

- by clients in hotels, motels and other residential type environments

- bed and breakfast type environments

The appliance must not be used in dusty environments or in the presence of extremely volatile

materials which could obstruct grids or heat exchanger, nor in very damp environments, in the

presence of inflammable products, or out of doors in the open. Any other use is to be considered

inappropriate and therefore dangerous. The manufacturer cannot be held responsible for eventual

damage caused by inappropriate, improper or irresponsible use and/or for repairs made to the

product by unauthorised personnel.

•

The appliance gets hot when working; so only touch the handle and plastic Knobs. Avoid

contact with the heating element.

•

Never move the appliance by pulling the cord.

• Children of less than 3 years should be kept away unless continuously supervised. Children aged

from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been

placed or installed in its intended normal operating position and they have been given supervision

or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance

or perform user maintenance.

CAUTION: Some parts of this product can become very hot and cause burns. Particular

attention has to be given where children and vulnerable people are present.

•

This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way and if

they understand the hazards involved. Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children without supervision.

•

Attention: when using electric appliances, the basic safety precautions must always be

observed to avoid risks of fire, electric shocks and physical injury.

•

Unplug the appliance when not in use.

This symbol show: WARNING: In order to avoid overheating, do not cover

the heater.

7/28

Assembly page 7/28



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

• That the user must not leave the appliance unattended while it is connected to the supply.

•

Do not touch the heater with wet hands or feet.

• Do not expose the heater to the weather (sun, rain, etc.)

• If the appliances falls or works badly, disconnect the electrical cable immediately. Check

that no part is damaged and switch it on after these controls: in case of doubt, contact

professionally qualified persons.

•

Do not pull on the power cord or the appliance to unplug the appliance from the electric

socket.

•

If the electric cord is damaged, it has to be replaced by the supplier or an authorized service center

or a professionally qualified, to avoid any risks.

•

Use this heating convector only and always in an upright position.

• Ensure that the appliance can heat up; for this purpose, check that the air inlet and outlet

openings are free from obstructions: do not leave anything hanging over or under the

appliance. In the event of overheating, the incorporated safety device stops the convector

heater from working.

INSTALLATION

• After removing the packing materials, check the integrity of the appliance; if you are unsure, do not

use it and ask for qualified professional help. The packing materials (plastic bags, polystyrene

foam, nails, etc.) must be kept out the reach of children because they are potential sources of

danger; but dispose of them in accordance with current law. Attention: please remove any

adhesive or advertising sheet stuck to the aspiration and air grid or to the base before use the

device.

• Before connecting the appliance, check that the voltage shown on the data plate matches that of

your electricity (220-240V~ 50Hz). In the event of incompatibility between the electric outlet and

the plug of the appliance, have the outlet replaced with another more suitable type by

professionally qualified personnel, who will make sure that the section of the wires of the outlet is

appropriate for the absorbed power of the appliance. In general, the use of adapters or extension

cords is not recommended; if their use is indispensable, they must conform to existing safety

standards and their current capacity (amperes) must not be less that the maximum of the appliance.

• Position the thermoconvector far from other sources of heat, inflammable materials (curtains,

carpets, etc.), inflammable gases or explosive materials (spray cans) and from materials that can

deform on exposure to heat. Make sure that there is 100 cm of free space in front of the appliance

and 30 cm on the sides. Do not use the heater in places where it could be subject to shocks in the

immediate vicinity of a bathtub, shower or swimming pool to avoid drops of water falling on the

heater or the heater falling in the water: If the appliance should accidentally get wet or be

submerged in water, remove the plug from the supply socket immediately and dry the unit

carefully. Check that no liquid has gone inside and if in doubt, contact professionally qualified

personnel.

• The support surface must be stable and not sloping (since the heater could tip over).

• Make sure that the cable is correctly positioned, that it is not touching hot elements or sharp edges,

is not wound around the utensil, is not twisted up on itself or in the way to prevent the utensil from

being pulled over. Check that you cannot trip over to prevent accidental falls or harm to persons.

• The appliance must not be positioned immediately under a socket.

• Please pay attention to the aspiration and dissipation air grids, in order to avoid obstructions, fire

risks or eventual device overheating. Please do not cover the device and do not use it to dry the

linen.

8/28

Assembly page 8/28



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

• Ensure that the fan works correctly: if this is not the case, switch off the appliance and have it

checked by professionally qualified personnel.

• The power socket must be easy to reach so the plug can be removed quickly in case of emergency.

• Do not use the appliance with a timer or a programmer or with a system that can switch on the

appliance automatically, to avoid risk of fire, since a fire risk exists if the heater is covered or

positioned incorrectly.

• In the case of a breakdown or fault, switch off the appliance and have it checked by a

professionally qualified technician; repairs made by unqualified persons can be dangerous and

render void the warranty.

• All repairs should be made by a competent qualified electrician. Any faulty appliances should be

returned to this service.

Portable installation

In order to use the appliance the two feet supplied must be fitted to the same by operating as follows:

- Always unplug the appliance before you assemble.

- Put the appliance down horizontally on a flat, smooth surface.

- Position the feet by inserting the hook into the slot on the side and make it run until the lower

hooks block

- Secure their blocking using the screws supplied.

Wall installation

1) With wall installation, the wall to which the appliance is secured must be made of masonry and/or

of heat-resistant material (not wood, or synthetic material which can easily overheat); also, follow

these indications for the installation:

2) The appliance must be positioned so that the bottom side is away from the floor min. 90mm÷

100mm max from the floor.

3) The upper grill is perfectly horizontal.

4) At a distance of at least 20 cm from the corners of walls.

5) At a distance of at least 100 cm from flammable materials (curtains, fabrics, etc.).

6) Not beneath socket outlets

- Fit two hooks (fig.2) to the wall at a distance of 51,2 cm apart and at least (see fig.2)

- Insert the metal bracket into the lower grill half way up the rear panel (vedi fig.3)

- Hang the convector heater on the wall by inserting the hooks into the slots provided in the rear

panel (see fig.4)

- Mark the exact positioning of the hole at the centre of the metal bracket on the wall; make a hole

in the wall and use a screw to secure the appliance to the wall in this way.

9/28

Assembly page 9/28



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

DESCRIPTION OF THE APPLIANCE

1) Thermostat knob

2) 1250 W Switch

3) 750 W switch

4) Fan switch

USE

Before each use, verify that the unit is in good condition, the electric cord is not damaged, if the

power cord is damaged, it must be replaced by the manufacturer or a competent qualified electrician

or a person with similar qualifications, in order to avoid any risk.

Operate in the following way to use the convector heater:

1) Insert the plug in the socket

2) Turn the thermostat knob (1) clockwise to the position corresponding to the desired

temperature.

3) To switch the appliance on, press switch (2) to heat using 1250 W, or switch (3) to heat at

750W or both to heat at 2000W.

4) To start the fan (4) press switch (4).

5) The pilot light comes on an goes ot when the appliances reaches the set temperature

6) To switch the appliance off, return the switch buttons to the “0” pos. and turn the thermostat

knob anticlockwise. Remove the plug from the power socket.

Never leave the appliance connected to the socket if it is not in use, especially for long periods.

Anti-frost device

Insert the plug into the power socket, press switches (2) and (3) and turn the thermostat knob to the

anti-frost position (*): this permits convector heater switching on when the ambient temperature falls

below +5°C.

10/28

Assembly page 10/28



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

CLEANING AND MAINTENANCE

Attention: before cleaning the appliance, switch off, unplug and wait for before it has

completely cooled down.

• Periodically check that the air-intake grill is not obstructed by fuzz or threads, to clean and

maintain of the grid, it is possible vacuum cleaner paying attention not to damage the electrical

resistance.

• To clean the body use a soft damp cloth; do not use abrasive products.

• For long periods of inactivity, you must cover it and place it in a dry place; it is advisable to put

it in its original packaging to protect it from dust and humidity.

• If you decide not to use the appliance any more, we recommend making it inoperative by

cutting the power cord (after making sure you have disconnected the plug from the socket) and

make dangerous parts harmless if children are allowed to play with them.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN

ACCORDANCE WITH EC DIRECTIVE 2011/65/EC.

At the end of its working life, the product must not be disposed of as urban waste. It must be taken to

a special local authority differentiated waste collection centre or to a dealer providing this service.

Disposing of a household appliance separately avoids possible negative consequences for the

environment and health deriving from inappropriate disposal and enables the constituent materials to

be recovered to obtain significant savings in energy and resources. As a reminder of the need to

dispose of household appliances separately, the product is marked with a crossed-out wheeled

dustbin.

11/28

Assembly page 11/28

Page is loading ...



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

DESCRIPTION DE L'APPAREIL

1) Bouton thermostat

2) Interrupteur 1250 W

3) Interrupteur 750 W

4) Interrupteur de l’hélice

FONCTIONNEMENT

Avant chaque utilisation, vérifiez que l'appareil est en bon état, le cordon électrique n'est pas

endommagé, si le cordon d'alimentation est endommagé, il doit être remplacé par le fabricant ou

son agent de service ou par une personne des qualifications semblables, afin d'éviter tout risque.

En ce qui concerne l’emploi, on procède de la façon suivante :

1) Insérez la fiche dans la prise de courant.

2) Faites tourner le bouton du thermostat (1) dans le sens des aiguilles d’une montre dans la

position qui correspond à la température désirée.

3) Pour allumer l’appareil, appuyez sur l’interrupteur (2) pour chauffer à 1250 W, ou sur

l’interrupteur (3) pour chauffer à 750 W ou sur tous les deux pour réchauffer à 2000 W.

4) Pour actionner l’hélice (4), appuyez sur l’interrupteur (4).

5) Le signal lumineux s’allume et reste allumé jusqu’à ce que l’appareil atteigne la température

sélectionnée .

15/28

Assembly page 15/28

Page is loading ...



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

BESCHREIBUNG DES GERÄTES

1) Temperaturregler

2) Schalter 1250 W

3) Schalter 750 W

4) Gebläseschalter

BETRIEB DES HEIZLÜFTERS

Vor jedem Einsatz überprüfen, ob das Gerät in gutem Zustand ist, das elektrische Kabel ist nicht

beschädigt, wenn das Netzkabel beschädigt ist, muss es durch den Hersteller oder seinen

Kundendienst oder eine Person ersetzt werden, mit ähnliche Qualifikationen, um jegliches Risiko zu

vermeiden.

Beim Gebrauch auf folgende Weise vorgehen:

1) Stecken Sie den Stecker in die Steckdose.

2) Drehen Sie den Temperaturregler (1) nach rechts auf die gewünschte Temperatur.

3) Schalten Sie das Gerät mit dem Schalter (2) zum Heizen mit 1250 W oder mit dem Schalter (3)

zum Heizen mit 750 W ein; oder drücken Sie beide Schalter, wenn Sie mit einer Leistung von

2000 W heizen möchten.

4) Schalten Sie das Gebläse (4) mit Schalter (4) ein.

5) Die Betriebsanzeige leuchtet auf und erlischt nach Erreichen der eingestellten Temperatur.

6) Zum Abschalten des Gerätes die Schalter auf Position “0” stellen und den Temperaturregler nach

links drehen. Ziehen Sie nach der Benutzung immer den Netzstecker.

Bei längerem Gerätestillstand den Stecker aus der Steckdose ziehen.

20/28

Assembly page 20/28

Page is loading ...



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

- Introducir el soporte metálico en la rejilla inferior a mitad del panel posterior (véase fig.3);

- Colgar el termoconvector a la pared, introduciendo los ganchos en las ranuras correspondientes

ubicadas en el panel posterior (véase fig. 4);

- Marcar en la pared la posición exacta del orificio en el centro del soporte de metal, perforar la

pared y fijar con tornillos para bloquear la unidad en la pared.

5) Perilla termostato

6) Interruptor 1250W

7) Interruptor 750W

8) Interruptor ventilador

USO

Antes de cada uso comprobar que el aparato se encuentre en buen estado, que el cable eléctrico no se

encuentre dañado: Si el cable eléctrico está dañado, debe ser sustituido por el fabricante o por el

servicio de asistencia técnica o por personal técnico capacitado, en modo de prevenir cualquier tipo de

riesgos.

Para el empleo del termoconvector siga las siguientes indicaciones:

1) Introducir el enchufe en la toma de corriente.

2) Girar la perilla termostato (1) en sentido horario en la posición correspondiente a la temperatura

deseada.

25/28

Assembly page 25/28

Page is loading ...



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

27/28

Assembly page 27/28



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

Fax +32 030 9904733

Via G.Amendola, 16/18

25019 Sirmione (BS) – ITALY

www.bimar-spa.it e-mail: info@bimar-spa.it

Servizio clienti Bimar: 8955895542

28/28

Assembly page 28/28

Bimar CALDISSIMO (type S598.EU mod.CH 3000 TURBO) Owner's manual

This manual is also suitable for

Bimar CALDISSIMO (type S598.EU mod.CH 3000 TURBO) Owner's manual

in other languages

Related papers

Other documents