ONKYO A-9130 Owner's manual

Brand: ONKYO

Model: A-9130

Type: Owner's manual

INTEGRATED AMPLIFIER

A-9130

Instruction Manual

Before use

Preparations

Basic Operations

Others

SN29403409_A-9130_En_1806XX.book 1 ページ２０１８年７月１２日　木曜日　午後８時４５分

Before use

Be fore us e

Before use

What’s in the box ................................................ 2

Safety Information .............................................. 3

Part Names ............................................................ 4

Front Panel ........................................................ 4

Rear Panel ......................................................... 5

Remote Controller ..............................................6

Preparations

Connections .......................................................... 8

Connecting speakers ......................................... 8

Connecting a Powered subwoofer ..................... 9

Connecting players (DIGITAL IN connection) .... 9

Connecting players (LINE IN connection) ........ 10

Connecting players (Turntable connection) ..... 10

Connecting with Onkyo RI Components ...........11

Using this unit as a power amplifier ................. 12

Power Cord Hookup.......................................... 12

Setup .................................................................... 13

Remote controller preparations ........................ 13

Turn on the power of the unit ........................... 13

Speaker impedance settings ............................ 14

RI function settings .......................................... 15

Basic Operations

Playback .............................................................. 16

Switching input and adjusting the volume ........ 16

Subwoofer output settings ............................... 17

Using the Direct Function ................................. 18

Adjusting the sound quality and balance ......... 18

Switching the unit to power amplifier mode ...... 19

Others

Useful functions ................................................. 20

Setting auto standby ........................................ 20

Troubleshooting ................................................. 21

Specifications ..................................................... 23

1. Main unit (1)

2. Remote controller (RC-968S) (1), batteries (AAA/R03) (2)

3. Power Cord (1)

≥ Instruction Manual (This document)

0 Connect speakers with 4 ≠ to 16 ≠ impedance.

0 The power cord must be connected only after all other

cable connections are completed.

0 We will not accept responsibility for damage arising from

the connection of equipment manufactured by other

companies.

0 Specifications and appearance are subject to change

without prior notice.

Table of Contents What’s in the box







SN29403409_A-9130_En_1806XX.book 2 ページ２０１８年７月１２日　木曜日　午後８時４５分

Before use

Safety Information

The lightning flash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user

to the presence of uninsulated "dangerous

voltage" within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

WARNING

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This equipment is not waterproof. To prevent a fire or shock hazard, do

not place any container filled with liquid near this equipment (such as a

vase or flower pot) or expose it to dripping, splashing, rain or moisture.

To prevent a fire hazard, do not place any naked flame sources (such as

a lighted candle) on the equipment.

Store small parts out of the reach of children and infants. If accidentally

swallowed, contact a doctor immediately.

Slots and openings in the cabinet are provided for ventilation to ensure

reliable operation of the product, and to protect it from overheating. To

prevent fire hazard, the openings should never be blocked or covered

with items (such as newspapers, tablecloths, curtains) or by operating

the equipment on thick carpet or a bed.

Do not use or store batteries in direct sunlight or other excessively hot

place, such as inside a car or near a heater. This can cause batteries to

leak, overheat, explode or catch fire. It can also reduce the life or

performance of batteries.

Risk of explosion if battery is replaced by an incorrect type. Risk of

explosion If disposal of a battery into fire or a hot oven, or mechanically

crushing or cutting of a battery.

Precautions

If you install the apparatus in a built-in installation, such as a bookcase or

rack, ensure that there is adequate ventilation.

Leave 20 cm (8”) of free space at the top and sides and 10 cm (4”) at the

rear. The rear edge of the shelf or board above the apparatus shall be

set 10 cm (4”) away from the rear panel or wall, creating a flue-like gap

for warm air to escape.

Operating Environment

Operating environment temperature and humidity: +5 °C to +35 °C (+41

°F to +95 °F); less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed

to high humidity or direct sunlight (or strong artificial light).

Important Notice

The model number and serial number of this equipment are on the rear

or bottom. Record these numbers on your enclosed warranty card and

keep in a safe place for future reference.

CAUTION

The power switch on this unit will not completely shut off all power from

the AC outlet. Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the AC outlet to shut

down all power. Therefore, make sure the unit has been installed so that

the power cord can be easily unplugged from the AC outlet in case of an

accident. To avoid fire hazard, the power cord should also be unplugged

from the AC outlet when left unused for a long period of time (for

example, when on vacation).

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

This product is for general household purposes. Any failure due to use

for other than household purposes (such as long-term use for business

purposes in a restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty period.

Power-Cord Caution

Handle the power cord by the plug. Do not pull out the plug by tugging

the cord and never touch the power cord when your hands are wet as

this could cause a short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the cord. Never make

a knot in the cord or tie it with other cords. The power cords should be

routed such that they are not likely to be stepped on. A damaged power

cord can cause a fire or give you an electrical shock. Check the power

cord once in a while. When you find it damaged, ask your nearest our

authorized service center or your dealer for a replacement.

For European models

Information for users on collection and disposal of old equipment

and used batteries

These symbols on the products, packaging, and/or accompanying

documents mean that used electrical and electronic products and

batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used

batteries, please take them to applicable collection points in

accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to

save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products and

batteries, please contact your local municipality, your waste disposal

service or the point of sale where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities

or dealer and ask for the correct method of disposal.

WEEE

http://www.onkyo.com/manual/weee/weee.pdf

Symbol for

equipment

Symbol examples

for batteries

SN29403409_A-9130_En_1806XX.book 3 ページ２０１８年７月１２日　木曜日　午後８時４５分

Before use

1. Í ON/STANDBY button

2. Remote control sensor: Receives signals from the remote

controller.

0 The signal range of the remote controller is within

about 16y/5 m, at an angle of 20° on the perpendicular

axis and 30° to either side.

3. Volume controller

4. Input source indicators: The indicators light according to

the selected input source.

0 The indicator for the selected input source blinks when

MUTING (p6) is active.

5. INPUT dial: Switches the input source to be played.

6. BASS -/+ controller: Enhance or moderate the bass range

of the speakers. (p18)

7. TREBLE -/+ controller: Enhance or moderate the treble

range of the speakers. (p18)

8. BALANCE L/R controller: Adjust the left/right audio

balance. (p19)

9. DIRECT button/indicator: Switch the DIRECT feature on

and off. The indicator lights when the DIRECT feature is

on. (p18)

10.

PHASE MATCHING BASS button/indicator: Switch the

PHASE MATCHING BASS feature on and off. The

indicator lights when the PHASE MATCHING BASS

feature is on. (p18)

11.

MAIN IN button/indicator: Button for making settings

when this unit is used as a power amplifier. The indicator

lights when the mode to use this unit as a power amplifier

is on. (p19)

12.

PHONES jack: Connect stereo headphones with a

standard plug (Ø1/4"/6.3 mm diameter).

Front Panel

Part Names



 



SN29403409_A-9130_En_1806XX.book 4 ページ２０１８年７月１２日　木曜日　午後８時４５分

Before use

1. RI REMOTE CONTROL jack: This jack is for linking when

you connect an Onkyo CD player, tuner, network audio

player, or RI dock that has an RI (“Remote Interactive”)

jack. (p11)

2. DIGITAL IN COAXIAL D1/DIGITAL IN OPTICAL D2 jacks:

Input digital audio signals from a playback device with a

digital coaxial cable or digital optical cable. (p9)

3. SPEAKERS terminals: Connect speakers with speaker

cables. (Not compatible with connection using banana

plugs or Y plugs.) (p8)

4. AC INLET: Connect the supplied power cord. (p12)

5. GND terminal: The ground wire of the turntable is

connected.

6. PHONO (MM) jacks: Use an Analog audio cable to

connect a Turntable that uses an MM type cartridge.

(p10)

7. LINE IN jacks: Input audio signals from a playback device

with an analog audio cable. (p10)

8. LINE OUT jacks: Use an Analog audio cable to output

audio signals to recording equipment, such as a cassette

tape deck. To select the input source for recording, use

the INPUT dial on this unit or use the remote controller.

9. MAIN IN jacks: When using this unit as a power amplifier,

connect the pre-amplifier here. (p12)

10.

SUBWOOFER PRE OUT jack: Connect a powered

subwoofer with a subwoofer cable. (p9)

Rear Panel

 









SN29403409_A-9130_En_1806XX.book 5 ページ２０１８年７月１２日　木曜日　午後８時４５分

Before use

Operating this unit

1. Í button: Sets this unit to On or Standby.

2. Cursors (D/C/B/A), ENTER button: Select the item

with the cursors and press ENTER to confirm.

3. VOLUME buttons

4. INPUT(D/C) buttons: Switches the input source to be

played.

5. SETUP button: Switches to the settings menu. Make

speaker impedance settings (p14), RI function settings

(p15), subwoofer output settings (p17), and auto

standby settings (p20).

6. RETURN button: Returns the display to the previous

display/state during setting.

7. MUTING button: Temporarily mutes audio. Press again to

cancel muting.

8. DIRECT button: Switch the DIRECT feature on and off.

(p18)

9. PM BASS button: Switch the PHASE MATCHING BASS

feature on and off. (p18)

Remote Controller



















SN29403409_A-9130_En_1806XX.book 6 ページ２０１８年７月１２日　木曜日　午後８時４５分

Before use

Operating other components

You can operate Onkyo CD players, tuners, network audio players, and RI docks with the remote controller of this unit.

∫ Operating an Onkyo CD player

Point the remote controller at the CD player’s remote control

sensor and operate.

10.

CD Í button

11.

Play mode buttons

0 If you have a Network CD player, then the RI function

enables use of the < and > buttons when you connect it

with an RI cable (p11). When using these buttons, point

the remote controller at the remote control sensor of this

unit.

∫ Operating an Onkyo tuner, network audio

player, or RI dock

You can use the RI function to centrally control with the

remote controller of this unit by connecting this unit and the

other audio components with an RI cable (p11). Point the

remote controller at the remote control sensor of this unit to

operate.

12.

Cursor buttons (D/C/B/A), ENTER button: Select items

with the cursor buttons and press ENTER to confirm.

13.

Play mode buttons

0 When using a network audio player, pressing the

MENU button returns to the previous display/state

during setting.

14.

INPUT button

0 When using a tuner, this works as a BAND button.

0 The INPUT button is not used for RI docks.











SN29403409_A-9130_En_1806XX.book 7 ページ２０１８年７月１２日　木曜日　午後８時４５分

Preparations

a Speaker Cable

(Note) Speaker Impedance

Connect speakers with an impedance of 4 ≠ to 16 ≠.

Setup: You have to change the setting on this unit if any of

the connected speakers have 4 ≠ or more to less than 8 ≠

impedance. Change the speaker impedance setting to 4 ≠.

(p14)

Connect the Speaker Cables

Make correct connection between the unit’s jacks and

speaker’s jacks (+ side to + side, and - side to - side) for

each channel. If the connection is wrong, a bass sound will

not be reproduced properly due to reverse phase. Twist the

wires exposed from the tip of the speaker cable so that the

wires do not stick out of the speaker terminal when

connecting. If the exposed wires touch the rear panel, or the

+ side and - side wires touch each other, the protection

circuit will be activated.

Connecting speakers

Connections

1/2”~5/8”

(12~15 mm)

Right Left

SN29403409_A-9130_En_1806XX.book 8 ページ２０１８年７月１２日　木曜日　午後８時４５分

Preparations

a Subwoofer Cable

You can also connect a Powered subwoofer to the

SUBWOOFER PRE OUT jack to boost bass playback even

more. Use a subwoofer cable for connection.

You can switch the subwoofer output setting between auto/

on/off according to your preference. Refer to "Subwoofer

output settings" (p17) for details.

0 It is recommended to set this off if you are not using a

subwoofer.

a Digital Optical Cable, b Digital Coaxial Cable

Use a Digital coaxial cable to connect a player to the

DIGITAL IN COAXIAL D1 jack. Alternatively, use a Digital

optical cable to connect a player to the DIGITAL IN

OPTICAL D2 jack. Refer to "Connecting with Onkyo RI

Components" (p11) to use the RI function.

0 Only PCM audio is supported for input through the

DIGITAL IN OPTICAL/COAXIAL jacks. Set the audio

output on the playback device to output PCM.

Connecting a Powered subwoofer

Powered subwoofer

Connecting players (DIGITAL IN

connection)

Tuner

SN29403409_A-9130_En_1806XX.book 9 ページ２０１８年７月１２日　木曜日　午後８時４５分

Preparations

a Analog Audio Cable

Use an Analog audio cable to connect a player to one of the

LINE IN 1/2/3/4/5 jacks. Refer to "Connecting with Onkyo RI

Components" (p11) to use the RI function.

a Analog Audio Cable

Use an analog audio cable to connect a turntable that uses

an MM-type cartridge to the PHONO (MM) jack.

If the turntable has a ground wire, connect it to the GND

terminal. With some turntables, connecting the ground wire

may cause hum, in which case it should be disconnected.

0 If the turntable has a built-in audio equalizer, connect it to

an LINE IN jack other than the PHONO (MM) jack. Also, if

the turntable uses an MC type cartridge, install an audio

equalizer compatible with the MC type cartridge between

the unit and the turntable, then connect to any LINE IN

jack other than the PHONO (MM) jack.

Connecting players (LINE IN

connection)

Tuner

Connecting players (Turntable

connection)

Turntable

SN29403409_A-9130_En_1806XX.book 10 ページ２０１８年７月１２日　木曜日　午後８時４５分

Preparations

a RI Cable, b Digital Coaxial Cable

Connection and Setup

If you have an Onkyo CD player, tuner, network audio

player, or RI dock, if these have RI jacks, then you can

connect them to this unit and link switching between on and

standby, and use the remote controller of this unit to

centrally control the equipment. (RI function)

These linked operations are enabled by the connection with

an RI cable between the equipment with an RI jack and this

unit, and the connection using a Digital cable or Analog

audio cable. Refer to the following table for connections.

When connecting to the DIGITAL IN COAXIAL D1 jack, use

a Digital coaxial cable. When connecting to the DIGITAL IN

OPTICAL D2 jack, use a Digital optical cable. When

connecting to LINE IN 1/2/3, use an Analog audio cable.

(*)Setup: When connecting a CD player or tuner, settings

are required to use the RI function. Refer to "RI function

settings" (p15) for details.

The RI function

The follow system functions can be used with the RI

function.

0 Some functions may not be supported depending on the

product even when an RI connection is used.

∫ Auto Power On

When this unit is in standby mode, if a component

connected by an RI cable is turned on, this unit

automatically turns on.

∫ Direct change

When playback is started on a component connected via RI,

the unit selects that component as the input source.

∫ System off

When this unit is turned off, components connected by an RI

cable are automatically turned off.

∫ Remote controller operations

You can use the remote controller of this unit to centrally

control components by connecting with an RI cable. Refer to

"Remote Controller" - "Operating other components" (p7)

for information about the buttons and operations for the

components.

0 The RI feature on this unit supports Onkyo CD players,

tuners, network audio players, and RI docks only. It does

not work properly with other devices such as MD

recorders. Refer to the instruction manual of the

component with the RI jack for details.

Connecting with Onkyo RI

Components

Equipment connected Jack to connect to

CD player (*) DIGITAL IN COAXIAL D1

or LINE IN 1

Tuner (*) DIGITAL IN OPTICAL D2 or

LINE IN 2

Network audio player / RI

dock

LINE IN 3

SN29403409_A-9130_En_1806XX.book 11 ページ２０１８年７月１２日　木曜日　午後８時４５分

Preparations

a Analog Audio Cable

Connect your pre-amplifier and you can use this unit as a

power amplifier. Connect the MAIN IN jacks of the unit and

the PRE OUT jacks of the pre-amplifier with an analog audio

cable.

0 Do not connect a source device (CD device, etc.) to the

MAIN IN jack. Doing so may produce high-volume sound

that can damage the unit, speakers, and various other

devices.

Setup: Switch the unit to power amplifier mode to use this

unit as a power amplifier. (p19)

a Power Cord

This model includes a removable power cord. The power

cord must be connected only after all other connections are

completed. Make sure you first connect the power cord to

AC INLET terminal of the unit and then connect to the outlet.

Always disconnect the outlet side first when disconnecting

the power cord.

Using this unit as a power amplifier

Pre-amplifier

Power Cord Hookup

SN29403409_A-9130_En_1806XX.book 12 ページ２０１８年７月１２日　木曜日　午後８時４５分

Preparations

Match the polarity when inserting the batteries.

Press Í ON/STANDBY on this unit or Í on the remote

controller.

Setup

Remote controller preparations

Turn on the power of the unit

SN29403409_A-9130_En_1806XX.book 13 ページ２０１８年７月１２日　木曜日　午後８時４５分

Preparations

Depending on the speakers you connect, you may need to

change the speaker impedance setting on this unit. Refer to

the page describing speaker connection (p8) and do the

following procedures if the change is required.

1. Press SETUP on the remote controller.

0 If this unit is set to be used as a power amplifier, the

SETUP button will not work. Check the setting. (p19)

2. Press D/C on the remote controller several times so

that input source indicators on the unit, such as "LINE 1"

and "LINE 2", start blinking.

0 The indicators blink and the current setting is

displayed.

3. Press B/A on the remote controller to change the

setting.

-4 ≠: "LINE 1" and "LINE 2" indicators are blinking

-8 ≠ (default value): "LINE 1", "LINE 2", "LINE 3" and

"LINE 4" indicators are blinking

4. To exit the settings, press SETUP.

0 The setting mode ends after 5 seconds elapse with no

operations performed.

Speaker impedance settings

8Ω

4Ω

SETUP

///

(BLINKING)

SN29403409_A-9130_En_1806XX.book 14 ページ２０１８年７月１２日　木曜日　午後８時４５分

Preparations

When connecting an Onkyo CD player or tuner to the RI

REMOTE CONTROL jack on this unit (p11) and using the

RI function, you need to make RI function settings.

1. Press SETUP on the remote controller.

0 If this unit is set to be used as a power amplifier, the

SETUP button will not work. Check the setting. (p19)

2. Press D/C on the remote controller several times to

switch to the RI function setting mode.

0 When connecting a CD player, make it so that one of the

"D1" and "LINE 1" indicators blinks and the other one

lights.

0 When connecting a tuner, make it so that one of the "D2"

and "LINE 2" indicators blinks and the other one lights.

3. Press B/A on the remote controller to switch the setting.

(When connecting a CD player)

- When connecting to the DIGITAL IN COAXIAL D1 jack

(default value): The "D1" indicator blinks and "LINE 1"

lights.

- When connecting to the LINE IN 1 jack: The "LINE 1"

indicator blinks and "D1" lights.

(When connecting a tuner)

- When connecting to the DIGITAL IN OPTICAL D2 jack

(default value): The "D2" indicator blinks and "LINE 2"

lights.

- When connecting to the LINE IN 2 jack: The "LINE 2"

indicator blinks and "D2" lights.

4. To exit the settings, press SETUP.

0 The setting mode ends after 5 seconds elapse with no

operations performed.

RI function settings

(CD)

(Tuner)

Linked D2

Linked LINE IN 2

Linked D1

Linked LINE IN 1

SETUP

///

(BLINKING) (LIGHTING)

SN29403409_A-9130_En_1806XX.book 15 ページ２０１８年７月１２日　木曜日　午後８時４５分

Basic Operations

Perform the following procedure when the unit is on.

1. Press INPUTD/C on the remote controller to switch to

the input with the same name as the jack to which you

have connected the player.

For example, switch to D1 to play the device connected to

the DIGITAL IN COAXIAL D1 jack.

When operating on the main unit, turn the INPUT dial to

switch the input.

0 The indicator for the selected input source lights.

0 If there is no digital audio signal input while D1 or D2 is

selected, the indicator blinks while the source is

selected.

2. Start play on the connected player.

3. Press VOLUME on the remote controller or turn the

volume controller on the main unit to adjust the volume.

Playback

Switching input and adjusting the

volume

VOLUME

INPUT

SN29403409_A-9130_En_1806XX.book 16 ページ２０１８年７月１２日　木曜日　午後８時４５分

Basic Operations

This unit enables you to choose the subwoofer output mode,

with the choices being "Auto" (default setting), "On", and

"Off".

0 There is no audio output from the subwoofer when

headphones are connected, irrespective of the setting.

1. Press SETUP on the remote controller.

0 If this unit is set to be used as a power amplifier, the

SETUP button will not work. Check the setting. (p19)

2. Press D/C on the remote controller several times so

that some input source indicators, such as "LINE 1" and

"LINE 2", light on the unit.

0 The indicators light and the current setting is displayed.

3. Press B/A on the remote controller to change the

setting.

- Auto (default value): "LINE 1" and "LINE 2" indicators

light

- On: "LINE 1", "LINE 2" and, "LINE 3" indicators light

- Off: "LINE 1", "LINE 2", "LINE 3" and "LINE 4"

indicators light

4. To exit the settings, press SETUP.

0 The setting mode ends after 5 seconds elapse with no

operations performed.

Subwoofer output settings

OFF

AUTO

Auto : The subwoofer signal is not output when the

DIRECT function (p18) is on.

On : The subwoofer signal is always output.

Off : The subwoofer signal output is stopped, and the

effect on sound quality can be moderated within

the unit. It is recommended to set this off if you are

not using a subwoofer.

SETUP

///

(LIGHTING)

SN29403409_A-9130_En_1806XX.book 17 ページ２０１８年７月１２日　木曜日　午後８時４５分

Basic Operations

When you turn the DIRECT feature on (default value), the

unit bi-passes the tone control circuits that adjust the bass

and treble, taking the shortest route which favors sound

quality.

0 PHASE MATCHING BASS/BASS/TREBLE cannot be

adjusted when DIRECT feature is on.

1. Press DIRECT on the main unit or the remote controller to

switch on or off. The DIRECT indicator lights when on.

PHASE MATCHING BASS

Turning the PHASE MATCHING BASS function on

maintains smooth and powerful bass reproduction while

effectively keeping the mid-range clear and making vocals

and strings stand out (The default value is “off”).

0 This cannot be set when DIRECT is on (default value).

Press DIRECT to turn the DIRECT indicator off before

operating. Note that the PHASE MATCHING BASS

setting reverts to the previous setting when the DIRECT

function is turned off.

1. Press PHASE MATCHING BASS on the main unit or PM

BASS on the remote controller to switch on or off. The

PHASE MATCHING BASS indicator lights when on.

BASS (main unit only)

0 This cannot be set when DIRECT is on (default value).

Press DIRECT to turn the DIRECT indicator off before

operating.

1. Turn the BASS -/+ controller to enhance or moderate the

bass.

TREBLE (main unit only)

0 This cannot be set when DIRECT is on (default value).

Press DIRECT to turn the DIRECT indicator off before

operating.

Using the Direct Function

DIRECT

Adjusting the sound quality and

balance

PMBASS

SN29403409_A-9130_En_1806XX.book 18 ページ２０１８年７月１２日　木曜日　午後８時４５分

Basic Operations

1. Turn the TREBLE -/+ controller to enhance or moderate

the treble.

BALANCE (main unit only)

1. Turn the BALANCE L/R controller on the main unit to

adjust the balance of the sounds output from the left and

right speakers.

Perform the following operations to switch the unit to power

amplifier mode to use this unit as a power amplifier when

you have connected a pre-amplifier to the MAIN IN jack on

this unit (p12).

0 Power amplifier modes settings are not available if

headphones are connected.

1. Press and hold MAIN IN until the "DIRECT" and "MAIN

IN" indicators light on the main unit. Press and hold MAIN

IN to cancel the power amplifier mode.

Note that the power amplifier mode is not canceled even

if this unit goes to standby mode.

0 When you cancel the power amplifier mode, BASS,

TREBLE, BALANCE, DIRECT, and PHASE MATCHING

BASS revert to the settings prior to changing to the power

amplifier mode.

0 There is no audio output from the PHONES jack and

LINE OUT jacks while the power amplifier mode is

engaged. The following functions are also unavailable

while the power amplifier mode is on.

“Speaker impedance settings” (p14) / “RI function

settings” (p15) / “Switching input and adjusting the

volume” (p16) / “Subwoofer output settings” (p17) /

“Adjusting the sound quality and balance” (p18) /

“Setting auto standby” (p20)

0 When switched to power amplifier mode, if the volume of

the connected pre-amplifier is low, auto standby (p20)

may function and the power may automatically switch to

standby. If this happens, you may be able to fix it by

increasing the volume on the pre-amplifier.

0 Also read the instruction manual of the pre-amplifier you

connected to this unit.

Switching the unit to power

amplifier mode

SN29403409_A-9130_En_1806XX.book 19 ページ２０１８年７月１２日　木曜日　午後８時４５分

Others

When automatic standby is on (default value), the unit

automatically switches to standby mode after 20 minutes of

no audio input without any operations.

1. Press SETUP on the remote controller.

0 If this unit is set to be used as a power amplifier, the

SETUP button will not work. Check the setting. (p19)

2. Press D/C on the remote controller several times to

make the "DIRECT" and "PHASE MATCHING BASS"

indicators either blink or light.

0 The indicators blink or light and the current setting

value is displayed.

3. Press B/A on the remote controller to switch auto

standby on or off.

- On (default value): "DIRECT" and "PHASE MATCHING

BASS" indicators are blinking

- Off: "DIRECT" and "PHASE MATCHING BASS"

indicators light

4. To exit the settings, press SETUP.

0 The setting mode ends after 5 seconds elapse with no

operations performed.

0 60 seconds before switching to standby mode, the input

source indicator for the currently selected source starts

blinking.

0 Depending on the connected device, the auto standby

feature may not engage due to factors such as noise.

Useful functions

Setting auto standby

(LIGHTING)

OFF

(BLINKING)

SETUP

///

SN29403409_A-9130_En_1806XX.book 20 ページ２０１８年７月１２日　木曜日　午後８時４５分

Page is loading ...

ONKYO A-9130 Owner's manual

Brand: ONKYO

Model: A-9130

Type: Owner's manual

Download PDF

report

in other languages

français: ONKYO A-9130 Le manuel du propriétaire
español: ONKYO A-9130 El manual del propietario

ONKYO A-9130 Owner's manual

ONKYO A-9130 Owner's manual

in other languages

Related papers

Other documents