WIKA CPT-20 tag:model:CPT-21 Operating instructions

Operating Instructions

Process pressure transmitter CPT-2x

Slave for electronic dierential pressure

With SIL qualication

Ceramic sensor

2

Contents

WIKA Operating Instructions - Process pressure transmitter CPT-2x

Contents

1 About this document ............................................................................................................... 4

1.1 Function ........................................................................................................................... 4

1.2 Target group ..................................................................................................................... 4

1.3 Symbols used................................................................................................................... 4

2 For your safety ......................................................................................................................... 5

2.1 Authorised personnel ....................................................................................................... 5

2.2 Appropriate use ................................................................................................................ 5

2.3 Warning about incorrect use ............................................................................................. 5

2.4 General safety instructions ............................................................................................... 5

2.5 EU conformity ................................................................................................................... 6

2.6 SIL qualication according to IEC 61508 .......................................................................... 6

2.7 Permissible process conditions ........................................................................................ 6

2.8 Installation and operation in the USA and Canada ........................................................... 6

3 Product description ................................................................................................................. 7

3.1 Conguration .................................................................................................................... 7

3.2 Principle of operation........................................................................................................ 8

3.3 Supplementary cleaning procedures .............................................................................. 13

3.4 Packaging, transport and storage ................................................................................... 13

4 Mounting ................................................................................................................................. 15

4.1 General instructions ....................................................................................................... 15

4.2 Ventilation and pressure compensation .......................................................................... 16

4.3 Combination Master - Slave ........................................................................................... 18

4.4 Level measurement ........................................................................................................ 19

4.5 Dierential pressure measurement ................................................................................ 20

4.6 Interface measurement .................................................................................................. 21

4.7 Density measurement .................................................................................................... 22

4.8 Density-compensated level measurement ..................................................................... 23

4.9 External housing ............................................................................................................ 25

5 Connecting to power supply ................................................................................................. 26

5.1 Preparing the connection ............................................................................................... 26

5.2 Connecting ..................................................................................................................... 26

5.3 Single chamber housing ................................................................................................. 28

5.4 External housing with version IP 68 (25 bar)................................................................... 28

5.5 Connection example ...................................................................................................... 30

6 Functional safety (SIL) .......................................................................................................... 31

6.1 Objective ........................................................................................................................ 31

6.2 SIL qualication .............................................................................................................. 31

6.3 Application area ............................................................................................................. 31

6.4 Safety concept of the parameterization .......................................................................... 32

7 Set up with the display and adjustment module ................................................................ 34

7.1 Parameter adjustment .................................................................................................... 34

8 Diagnosis, asset management and service ........................................................................ 48

8.1 Maintenance .................................................................................................................. 48

8.2 Cleaning - hygienic connection with compression nut .................................................... 48

8.3 Rectify faults ................................................................................................................... 49

3

Contents

WIKA Operating Instructions - Process pressure transmitter CPT-2x

8.4 Exchange process module on version IP 68 (25 bar) ..................................................... 49

8.5 Instrument repair ............................................................................................................ 50

9 Dismount................................................................................................................................. 51

9.1 Dismounting steps.......................................................................................................... 51

9.2 Disposal ......................................................................................................................... 51

10 Supplement ............................................................................................................................ 52

10.1 Technical data ................................................................................................................ 52

10.2 Calculation of the total deviation ..................................................................................... 62

10.3 Practical example ........................................................................................................... 63

10.4 Dimensions .................................................................................................................... 66

10.5 Trademark ...................................................................................................................... 74

Safety instructions for Ex areas

Take note of the Ex specic safety instructions for Ex applications.

These instructions are attached as documents to each instrument

with Ex approval and are part of the operating instructions.

Editing status: 2017-11-23

4

1 About this document

WIKA Operating Instructions - Process pressure transmitter CPT-2x

1 About this document

1.1 Function

This operating instructions provides all the information you need for

mounting, connection and setup as well as important instructions for

maintenance, fault rectication, the exchange of parts and the safety

of the user. Please read this information before putting the instrument

into operation and keep this manual accessible in the immediate

vicinity of the device.

1.2 Target group

This operating instructions manual is directed to trained personnel.

The contents of this manual must be made available to the qualied

personnel and implemented.

1.3 Symbols used

Information, tip, note

This symbol indicates helpful additional information.

Caution: If this warning is ignored, faults or malfunctions can result.

Warning: If this warning is ignored, injury to persons and/or serious

damage to the instrument can result.

Danger: If this warning is ignored, serious injury to persons and/or

destruction of the instrument can result.

Ex applications

This symbol indicates special instructions for Ex applications.

•

List

The dot set in front indicates a list with no implied sequence.

→

Action

This arrow indicates a single action.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.

Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

5

2 For your safety

WIKA Operating Instructions - Process pressure transmitter CPT-2x

2 For your safety

2.1 Authorised personnel

All operations described in this documentation must be carried out

only by trained, qualied personnel authorised by the plant operator.

During work on and with the device, the required personal protective

equipment must always be worn.

2.2 Appropriate use

CPT-2x is a slave sensor for electronic dierential pressure measure-

ment.

You can nd detailed information about the area of application in

chapter "Product description".

Operational reliability is ensured only if the instrument is properly

used according to the specications in the operating instructions

manual as well as possible supplementary instructions.

2.3 Warning about incorrect use

Inappropriate or incorrect use of this product can give rise to applica-

tion-specic hazards, e.g. vessel overll through incorrect mounting

or adjustment. Damage to property and persons or environmental

contamination can result. Also, the protective characteristics of the

instrument can be impaired.

2.4 General safety instructions

This is a state-of-the-art instrument complying with all prevailing

regulations and directives. The instrument must only be operated in a

technically awless and reliable condition. The operator is responsi-

ble for the trouble-free operation of the instrument. When measuring

aggressive or corrosive media that can cause a dangerous situation

if the instrument malfunctions, the operator has to implement suitable

measures to make sure the instrument is functioning properly.

During the entire duration of use, the user is obliged to determine the

compliance of the necessary occupational safety measures with the

current valid rules and regulations and also take note of new regula-

tions.

The safety instructions in this operating instructions manual, the na-

tional installation standards as well as the valid safety regulations and

accident prevention rules must be observed by the user.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

trary conversions or modications are explicitly forbidden. For safety

reasons, only the accessory specied by the manufacturer must be

used.

To avoid any danger, the safety approval markings and safety tips on

the device must also be observed and their meaning read in this oper-

ating instructions manual.

6

2 For your safety

WIKA Operating Instructions - Process pressure transmitter CPT-2x

2.5 EU conformity

The device fulls the legal requirements of the applicable EU direc-

tives. By axing the CE marking, we conrm the conformity of the

instrument with these directives.

2.6 SILqualicationaccordingtoIEC61508

The Safety Integrity Level (SIL) of an electronic system is used to as-

sess the reliability of integrated safety functions.

For detailed specication of the safety requirements, multiple SIL

levels are specied according to safety standard IEC 61508. You can

nd detailed information in chapter "Functional safety (SIL)" of the

operating instructions.

The instrument meets the specications of IEC 61508: 2010 (Edi-

tion 2). It is qualied for single-channel operation up to SIL2. The

instrument can be used homogeneously redundant up to SIL3 in

multi-channel architecture with HFT 1.

2.7 Permissible process conditions

For safety reasons, the instrument must only be operated within the

permissible process conditions. You can nd detailed information on

the process conditions in chapter "Technical data" as well as on the

type label.

The permissible process pressure range is specied by "MWP"

(Maximum Working Pressure) on the type label, see chapter "Struc-

ture". The MWP takes the element of the measuring cell and process-

ing tting combination with the weakest pressure into consideration

and may applied permanently. The specication refers to a reference

temperature of +20 °C (+68 °F). It also applies when a measuring cell

with a higher measuring range than the permissible pressure range of

the process tting is installed order-related.

In order to prevent damage to the device, the test pressure may only

exceed the specied MWP briey by 1.5 times at reference tempera-

ture. The pressure stage of the process tting as well as the overload

resistance of the measuring cell are taken into consideration here

(see chapter "Technical Data").

In addition, a temperature derating of the process tting, e. g. with

anges, can limit the permissible process pressure range according

to the respective standard.

2.8 Installation and operation in the USA and

Canada

This information is only valid for USA and Canada. Hence the follow-

ing text is only available in the English language.

Installations in the US shall comply with the relevant requirements of

the National Electrical Code (ANSI/NFPA 70).

Installations in Canada shall comply with the relevant requirements of

the Canadian Electrical Code.

7

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

3 Product description

3.1 Conguration

The scope of delivery encompasses:

•

Instrument CPT-2x - Slave sensor

•

Ready-made connection cable, unassembled cable gland

•

Documentation

– Quick setup guide CPT-2x

– Safety Manual (SIL)

– Documentation instrument parameters (default values)

– Documentation order-relating instrument parameters (deviation

from default values)

– Test certicate for pressure transmitters

– Instructions for optional instrument features

– Ex-specic "Safety instructions" (with Ex versions)

– If necessary, further certicates

Information:

Optional instrument features are also described in this operating

instructions manual. The respective scope of delivery results from the

order specication.

This operating instructions manual applies to the following instrument

versions:

•

Hardware from 1.0.0

•

Software version from 1.0.0

Note:

You can nd the hardware and software version of the instrument as

follows:

•

On the type plate of the electronics module

•

In the adjustment menu under "Info"

The type label contains the most important data for identication and

use of the instrument:

Scope of delivery

Scope of this operating

instructions

Type label

8

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

4

1

5

10

12

11

13

14

3

2

6

7

8

9

Fig. 1: Layout of the type label (example)

1 Instrument type

2 Field for approvals

3 Signal output and voltage supply

4 Technical data

5 Product code

6 Order number

7 Serial number of the instrument

8 Symbol of the device protection class

9 ID numbers, instrument documentation

10 Reminder to observe the instrument documentation

11 SILidentication

3.2 Principle of operation

CPT-2x is suitable for applications in virtually all industries. It is used

for the measurement of the following pressure types.

•

Gauge pressure

•

Absolute pressure

•

Vacuum

Measured products are gases, vapours and liquids.

Depending on the process tting and measurement setup, measured

products can be also viscous or contain abrasive substances.

The electronic dierential pressure measurement is suitable for the

measurement of the following process variables:

•

Level

•

Flow

•

Dierential pressure

•

Density

•

Interface

•

Level, density-compensated

The CPT-2x slave sensor is combined with a sensor from the instru-

ment series for electronic dierential pressure measurement.

Application area

Measur

ed products

Measur

ed variables

Electronicdierential

pressure

9

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

1

2

Fig.2:Example,electronicdierentialpressureforlevelmeasurementinpres-

surized vessel

1 CPT-2x

2 CPT-2x, slave sensor

The sensors are connected via a screened four-wire cable. The

measured value from the slave sensor is read in and factored into the

calculations. Power supply and parameter adjustment are carried out

through the master sensor.

Information:

The sensor versions "Relative pressure climate-compensated" as

well as "Double chamber housing" are not suitable for connection of a

slave sensor.

You can nd further information in chapter "Combination Master -

Slave " of this operating instructions.

To reach the Safety Integrity Level (SIL) for the electronic dierential

pressure, both instruments must be SIL-qualied.

Sensor element is the measuring cell with robust ceramic diaphragm.

The process pressure deects the ceramic diaphragm and causes a

capacitance change in the measuring cell. This capacitance change

is converted into an electrical signal and output as measured value

via the output signal.

Measuring system pres-

sure

10

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

16 µm

1

2

3

Fig.3:Congurationoftheceramicmeasuringcell

1 Process diaphragm

2 Glass joint

3 Base element

A temperature sensor in the ceramic diaphragm of the ø 28 mm or on

the ceramic base of the ø 17.5 mm measuring cell detects the actual

process temperature. The temperature value is output via the master

sensor.

Extreme process temperature jumps are also immediately detected

by the ø 28 mm measuring cell. The values are compared with that of

an additional temperature measurement on the ceramic base body.

Within only a few measuring cycles the intelligent sensor electronics

compensates unavoidable measurement deviations due to tempera-

ture shocks. Such shocks cause (depending on the set damping) only

slight, brief changes to the output signal.

Relative pressure: the measuring cell is open to the atmosphere.

The ambient pressure is detected in the measuring cell and compen-

sated. It thus has no inuence on the measured value.

Absolute pressure: the measuring cell is evacuated and encapsu-

lated. The ambient pressure is not compensated and does hence

inuence the measured value.

The following presentations show examples for the installation of the

ceramic measuring cell into the process tting and the dierent seal

concepts.

The recessed installation is particularly suitable for applications with

gases, vapours and clear liquids. The measuring cell seal is posi-

tioned laterally as well as in addition in front.

Measuring system tem-

per

ature

Pr

essure types

Seal concepts

Recessed installation

11

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

1

2

5

6

3

4

Fig. 4: Recessed installation of the measuring cell (example: manometer con-

nection G½)

1 Measuring cell

2 Seal for the measuring cell

3 Additional, front seal for measuring cell

4 Diaphragm

5 Processtting

6 Sealfortheprocesstting

The front-ush installation is particularly suitable for applications with

viscous and abrasive media and in case of buildup. The measuring

cell seal is positioned laterally.

2

3

4

1

5

Fig.5:Front-ushinstallationofthemeasuringcell(example:threadG1½)

1 Sealfortheprocesstting

2 Measuring cell

3 Seal for the measuring cell

4 Processtting

5 Diaphragm

The completely front-ush mounting is particularly suitable for ap-

plications in the paper industry. The diaphragm is in the pulp ow, is

hence cleaned and protected against buildup.

Front-ushmountingwith

single seal

Completelyfront-ush

mounting with single seal

12

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

1

2

3

4

5

Fig.6:Front-ushinstallationofthemeasuringcell(example:M30x1.5)

1 Measuring cell

2 Seal for the measuring cell

3 Sealfortheprocesstting

4 Processtting

5 Diaphragm

The front-ush installation is particularly suitable for applications with

viscous media. The additional, front sealing protects the glass joint

of the measuring cell against chemical attack and the measuring cell

electronics against diusion of aggressive gases from the process.

1

2

3

4

5

Fig.7:Front-ushinstallationofthemeasuringcellwithdoubleseal(example:

angeconnectionwithextension)

1 Measuring cell

2 Seal for the measuring cell

3 Processtting

4 Additional, front seal for measuring cell

5 Diaphragm

The front-ush, hygienic installation of the measuring cell is particu-

larly suitable for food applications. The sealings are installed gap-free.

The form seal of the measuring cell protects also the glass joint.

1

2

3

4

5

Fig.8:Hygienicinstallationofthemeasuringcell(example:hygienicttingwith

compression nut)

1 Measuring cell

2 Form seal for the measuring cell

3 Gap-freesealforprocesstting

4 Processtting

5 Diaphragm

Front-ushmountingwith

double seal

Installation in hygienic

tting

13

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

The front-ush, hygienic installation of the measuring cell acc. to 3A

is particularly suitable for food applications. The sealings are installed

gap-free. The additional front sealing for the measuring cell protects

also the glass joint. A hole in the process tting is used for leakage

detection.

1

6

2

3

4

5

Fig. 9: Hygienic installation of the measuring cell acc. to 3-A (example: Clamp

connection)

1 Measuring cell

2 Seal for the measuring cell

3 Processtting

4 Additional, front seal for measuring cell

5 Diaphragm

5 Hole for leakage detection

3.3 Supplementary cleaning procedures

The CPT-2x is also available in the version "Oil, grease and silicone-

free". These instruments have passed through a special cleaning

procedure to remove oil, grease and paint-wetting impairment sub-

stances (PWIS).

The cleaning is carried out on all wetted parts as well as on surfaces

accessible from outside. To keep the purity level, the instruments are

immediately packed in plastic foil after the cleaning process. The

purity level remains as long as the instrument is kept in the closed

original packaging.

Caution:

The CPT-2x in this version may not be used in oxygen applications.

For this purpose, instruments are available in the special version "Oil

and grease-free for oxygen applications".

3.4 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.

The packaging of standard instruments consists of environment-

friendly, recyclable cardboard. For special versions, PE foam or PE

foil is also used. Dispose of the packaging material via specialised

recycling companies.

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Installation in hygienic

ttingacc.to3-A

Packaging

Transport

Transport inspection

14

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

Up to the time of installation, the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated, the packages must be stored only under

the following conditions:

•

Not in the open

•

Dry and dust free

•

Not exposed to corrosive media

•

Protected against solar radiation

•

Avoiding mechanical shock and vibration

•

Storage and transport temperature see chapter "Supplement -

Technical data - Ambient conditions"

•

Relative humidity 20 … 85 %

With instrument weights of more than 18 kg (39.68 lbs) suitable and

approved equipment must be used for lifting and carrying.

Storage

Storage and transpor

t

temperature

Lifting and carrying

15

4 Mounting

WIKA Operating Instructions - Process pressure transmitter CPT-2x

4 Mounting

4.1 General instructions

Make sure before mounting that all parts of the instrument exposed to

the process are suitable for the existing process conditions.

These are mainly:

•

Active measuring component

•

Process tting

•

Process seal

Process conditions in particular are:

•

Process pressure

•

Process temperature

•

Chemical properties of the medium

•

Abrasion and mechanical inuences

You can nd detailed information on the process conditions in chapter

"Technical data" as well as on the type label.

Protect your instrument against moisture ingress through the following

measures:

•

Use a suitable connection cable (see chapter "Connecting to

powersupply")

•

Tighten the cable gland or plug connector

•

When mounting horizontally, turn the housing so that the cable

gland or plug connector point downward

•

Lead the connection cable downward in front of the cable entry or

plug connector

This applies mainly to outdoor installations, in areas where high

humidity is expected (e.g. through cleaning processes) and on cooled

or heated vessels.

To maintain the housing protection, make sure that the housing lid is

closed during operation and locked, if necessary.

Make sure that the degree of contamination specied in chapter

"Technical data" meets the existing ambient conditions.

On devices with a threaded tting, the hexagon on the process tting

must be tightened with a suitable wrench.

See chapter "Dimensions" for wrench size.

Warning:

The housing or the electrical connection may not be used for screw-

ing in! Tightening can cause damage, e. g. to the rotation mechanism

of the housing.

If there is strong vibration at the mounting location, the instrument

version with external housing should be used. See chapter "External

housing".

Process conditions

Pr

otection against mois-

ture

Scr

ewing in

Vibrations

16

4 Mounting

WIKA Operating Instructions - Process pressure transmitter CPT-2x

Higher process temperatures often mean also higher ambient

temperatures. Make sure that the upper temperature limits stated in

chapter "Technical data" for the environment of the electronics hous-

ing and connection cable are not exceeded.

1

2

Fig. 10: Temperature ranges

1 Process temperature

2 Ambient temperature

4.2 Ventilation and pressure compensation

The lter element in the electronics housing has the following func-

tions:

•

Ventilation of the electronics housing

•

Atmospheric pressure compensation (with relative pressure meas-

uring ranges)

Caution:

The lter element causes a time-delayed pressure compensation.

When quickly opening/closing the housing cover, the measured value

can change for approx. 5 s by up to 15 mbar.

For an eective ventilation, the lter element must be always free from

buildup. In case of horizontal mounting, turn the housing so that the

lter element points downward after the instrument is installed. This

provides better protection against buildup.

Caution:

Do not use a high-pressure cleaner. The lter element could be dam-

aged, which would allow moisture into the housing.

The following paragraphs describe how the lter element is arranged

in the dierent instrument versions.

Temperature limits

Filter element - F

unction

17

4 Mounting

WIKA Operating Instructions - Process pressure transmitter CPT-2x

1 2 3

4 4 4

Fig.11:Positionofthelterelement-non-Ex,Ex-iaversion

1 Plastic, stainless steel housing (precision casting)

2 Aluminium housing

3 Stainless steel housing (electropolished)

4 Filter element

With the following instruments a blind plug is installed instead of the

lter element:

•

Instruments in protection IP 66/IP 68 (1 bar) - ventilation via capil-

laries in non-detachable cable

•

Instruments with absolute pressure

→

Turn the metal ring in such a way that the lter element points

downward after installation of the instrument. This provides better

protection against buildup.

1

2

Fig.12:Positionofthelterelement-Ex-dversion

1 Rotatable metal ring

2 Filter element

Instruments with absolute pressure have a blind plug mounted

instead of the lter element.

The process assembly of instruments with Second Line of Defense

(gastight leadthrough) is completely encapsulated. An absolute pres-

sure measuring cell is used so that no ventilation is required.

Filter element - Position

Ex-d version

Instruments with Second

Line of De

fense

18

4 Mounting

WIKA Operating Instructions - Process pressure transmitter CPT-2x

1

2

Fig.13:Positionofthelterelement-gastightleadthrough

1 Filter element

1

Fig.14:Positionofthelterelement-IP69Kversion

1 Filter element

Instruments with absolute pressure have a blind plug mounted

instead of the lter element.

4.3 Combination Master - Slave

In principle, any sensor combination within the instrument series is

allowed. The following requirements must be fullled:

•

Conguration, Master sensor suitable for electronic dierential

pressure

•

Pressure type is identical for both sensors, i.e. relative pressure/

relative pressure or absolute pressure/absolute pressure

•

Master sensor measures the higher pressure

•

Measurement setup as shown in the following chapters

The measuring range of each sensor is selected such that it ts the

measuring loop. For this, the max. recommended turn down must be

noted. See chapter "Technical data". It is absolutely necessary the the

measuring ranges of Master and Slave correspond.

Measurement result = Measured value of Master (total pres-

sure) - measured value of Slave (static pressure)

Depending on the application, individual combinations can result, see

following examples:

Data

Application: Level measurement

Medium: Water

Filter element - Position

IP 69K version

Example - large vessel

19

4 Mounting

WIKA Operating Instructions - Process pressure transmitter CPT-2x

Vessel height: 12 m, hydrostatic pressure = 12 m x 1000 kg/m

3

x

9.81 m/s

2

= 117.7 kPa = 1.18 bar

Superimposed pressure: 1 bar

Total pressure: 1.18 bar + 1 bar = 2.18 bar

Instrument selection

Nominal measuring range Master: 2.5 bar

Nominal measuring range Slave: 1 bar

Turn Down: 2.5 bar/1.18 bar = 2.1 : 1

Data

Application: Level measurement

Medium: Water

Vessel height: 500 mm, hydrostatic pressure = 0.50 m x 1000 kg/m

3

x

9.81 m/s

2

= 4.9 kPa = 0.049 bar

Superimposed pressure: 350 mbar = 0.35 bar

Total pressure: 0.049 bar + 0.35 bar = 0.399 bar

Instrument selection

Nominal measuring range Master: 0.4 bar

Nominal measuring range Slave: 0.4 bar

Turn Down: 0.4 bar /0.049 bar = 8.2 : 1

Data

Application: Dierential pressure measurement

Medium: Gas

Static pressure: 0.8 bar

Dierential pressure on orice: 50 mbar = 0.050 bar

Total pressure: 0.8 bar + 0.05 bar = 0.85 bar

Instrument selection

Nominal measuring range Master: 1 bar

Nominal measuring range Slave: 1 bar

Turn Down: 1 bar/0.050 bar = 20 : 1

The measuring result (level, pressure dierence) as well as meas-

ured value Slave (static or superimposed pressure) are output by the

sensor. Depending on the instrument version, output as 4 … 20 mA

signal or digitally via HART, Probus PA or Foundation Fieldbus.

To reach the Safety Integrity Level (SIL) for the electronic dierential

pressure, both instruments must be SIL-qualied.

4.4 Level measurement

The master/slave combination is suitable for level measurement in a

pressurized vessel

Keep the following in mind when setting up the measuring system:

•

Mount the master sensor below the min. level

Example - small vessel

Example-oricein

pipeline

Output measured values

Measurement setup

20

4 Mounting

WIKA Operating Instructions - Process pressure transmitter CPT-2x

•

Do not mount the master sensor close to the lling stream or

emptying area

•

Mount the master sensor so that it is protected against pressure

shocks from the stirrer

•

Mount the slave sensor above the max. level

1

2

Fig. 15: Measurement setup, level measurement in pressurized vessel

1 CPT-2x

2 CPT-2x, slave sensor

4.5 Dierentialpressuremeasurement

The master/slave combination is suitable for dierential pressure

measurement

Take note of the following instructions for the measurement setup, for

example in gases:

•

Mount the instruments above the measuring point

Possible condensation can then drain o into the process line.

Measurement setup

Page is loading ...

WIKA CPT-20 tag:model:CPT-21 Operating instructions

WIKA CPT-20 tag:model:CPT-21 Operating instructions

Related papers

Other documents