Smeg CR 325 ANF User manual

Category
Fridge-freezers
Type
User manual

This manual is also suitable for

18
INSTRUCTIONS FOR USE
BEFORE USING THE APPLIANCE
SAFEGUARDING THE ENVIRONMENT
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
INSTALLATION
GENERAL DESCRIPTION OF
REFRIGERATOR AND FREEZER OPERATION
USING THE REFRIGERATOR
COMPARTMENT
USING THE FREEZER COMPARTMENT
MAINTENANCE AND CLEANING
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
ELECTRICAL CONNECTION FOR GREAT
BRITAIN AND IRELAND ONLY
19
Your new appliance is designed exclusively for
domestic use.
To ensure best use of your appliance, carefully
read the operating instructions which contain
a description of the product and useful
advice.
Keep these instructions for future reference.
1. After unpacking the appliance, make sure it is
not damaged and that the door closes properly.
Any damage must be reported to the dealer
within 24 hours of delivery of the appliance.
2. Wait at least two hours before switching the
appliance on, to ensure that the refrigerant
circuit is fully efficient.
3. Installation and the electrical connection must
be carried out by a qualified technician
according to the manufacturer’s instructions
and in compliance with the local safety
regulations.
4. Clean the inside of the appliance before using it.
BEFORE USING THE APPLIANCE
1. Packing
The packing material is 100% recyclable and bears
the recycling symbol. For disposal, comply with the
local regulations. Keep the packing materials
(plastic bags, polystyrene parts, etc.) out of the
reach of children, as they are a potential source of
danger.
2. Scrapping/Disposal
The appliance is manufactured using recyclable
material.
This appliance is marked in compliance with
European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE). By
ensuring the correct disposal of this appliance, you
can help prevent potentially negative consequences
for the environment and the health of persons.
The symbol on the appliance, or on the
accompanying documents, indicates that this
appliance should not be treated as domestic waste
but must be taken to a special collection centre for
the recycling of electrical and electronic
equipment.
When scrapping the appliance, make it unusable by
cutting off the power cable and removing the
doors and shelves so that children cannot easily
climb inside and become trapped.
Scrap the appliance in compliance with local
regulations on waste disposal, taking it to a special
collection centre; do not leave the appliance
unattended even for a few days, since it is a
potential source of danger for children.
For further information on the treatment, recovery
and recycling of this product, contact your
competent local office, the household waste
collection service or the shop where you
purchased the appliance.
Information:
This appliance does not contain CFCs. The
refrigerant circuit contains R134a (HFC) or R600a
(HC) (see the rating plate inside the appliance).
Appliances with Isobutane (R600a): isobutane is a
natural gas without environmental impact, but is
flammable. Therefore, make sure the refrigerant
circuit pipes are not damaged.
This product may contain Fluorinated Greenhouse
Gases covered by the Kyoto Protocol; the
refrigerant gas is inside a hermetically sealed
system.
Refrigerant gas: R134a has a Global Warming
Potential of (GWP) 1300.
Declaration of conformity
This appliance has been designed for preserving
food and is manufactured in compliance with
Regulation (CE) No. 1935/2004.
This appliance has been designed, manufactured
and marketed in compliance with:
- safety objectives of the “Low Voltage"
Directive 2006/95/CE (which replaces
73/23/CEE and subsequent amendments);
- the protection requirements of Directive
“EMC" 89/336/EEC amended by Directive
93/68/EEC.
Electrical safety of the appliance can only be
guaranteed if it is correctly connected to an
approved earthing system.
SAFEGUARDING THE ENVIRONMENT
20
INSTALLATION
The appliance must be handled and installed by
two or more persons.
Be careful not to damage the floors (e.g.
parquet) when moving the appliance.
During installation, make sure the appliance
does not damage the power cable.
Make sure the appliance is not near a heat
source.
To guarantee adequate ventilation, leave a space
on both sides and above the appliance and
follow the installation instructions.
Keep the appliance ventilation openings free.
Do not damage the appliance refrigerant circuit
pipes.
Install and level the appliance on a floor strong
enough to take its weight and in a place suitable
for its size and use.
Install the appliance in a dry and well-ventilated
place. The appliance is arranged for operation
in places where the temperature comes within
the following ranges, according to the climatic
class given on the rating plate. The appliance
may not work properly if it is left for a long
time at a temperature outside the specified
range.
Make sure the voltage specified on the rating
plate corresponds to that of your home.
Do not use single/multi adapters or extension
cords.
For the water connection, use the pipe supplied
with the new appliance; do not reuse that of
the previous appliance.
Power cable modification or replacement must
only be carried out by qualified personnel.
It must be possible to disconnect the appliance
from the power supply by unplugging it or by
means of a mains two-pole switch installed
upstream of the socket.
SAFETY
Do not store or use petrol, flammable liquids
or gas in the vicinity of this or other electrical
appliances. The fumes can cause fires or
explosions.
Do not use mechanical, electric or chemical
means other than those recommended by the
Manufacturer to speed up the defrost process.
Do not use or place electrical devices inside the
appliance compartments if they are not of the
type expressly authorised by the Manufacturer.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
To avoid the risk of children becoming trapped
and suffocating, do not allow them to play or
hide inside the appliance.
Do not swallow the contents (non-toxic) of the
ice packs (in some models).
Do not eat ice cubes or ice lollies immediately
after taking them out of the freezer since they
may cause cold burns.
USE
Before carrying out any maintenance or
cleaning operation, unplug the appliance or
disconnect it from the power supply.
All appliances equipped with an automatic ice-
maker and water dispenser must be connected
to a water supply that only delivers drinking
water (with mains water pressure of between
0.17 and 0.81 Mpa (1.7 and 8.1 bar)).
Automatic ice-makers and/or water dispensers
not directly connected to the water supply
must be filled with drinking water only.
Use the refrigerator compartment only for
storing fresh food and the freezer compartment
only for storing frozen food, freezing fresh food
and making ice cubes.
Do not store glass containers with liquids in the
freezer since they may burst.
The Manufacturer declines any liability if the
above advice and precautions are not
respected.
Climatic Class Amb. T. (°C) Amb. T. (°F)
SN From 10 to 32 From 50 to 90
N From 16 to 32 From 61 to 90
ST From 16 to 38 From 61 to 100
T From 16 to 43 From 61 to 110
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
21
Install the appliance away from heat sources.
Direct exposure to sunlight or installation near
heat sources (radiators, cookers) will increase
energy consumption and should therefore be
avoided. If this is not possible, the following
minimum distances must be respected:
- 30 cm from coal or oil stoves;
- 3 cm from electric and/or gas cookers.
Clean the inside (refer to “Maintenance and
cleaning”).
Insert or install the accessories/parts supplied.
INSTALLATION
This appliance is a refrigerator combined with a
star rating electronically controlled freezer.
It therefore allows separate adjustment of the
temperature in the refrigerator and freezer
compartment.
The NO FROST freezer compartment
enables perfect freezing of fresh and cooked food,
the production of ice cubes and storing of frozen
and deep frozen food. Defrosting is automatic.
The refrigerator compartment, equipped with
automatic defrost, enables the storage of fresh
food and beverages.
Optimum performance depends on the climatic
class indicated on the rating plate.
Vacation" Option
The electronic control allows the freezer
compartment to be left on with the refrigerator
compartment switched off.
To activate this function, with the appliance on,
press the button (5) for 3 seconds until the
refrigerator compartment display (7) goes off and
the green light (6) comes on; the freezer display
(4) will remain on. For technical reasons, the
freezer compartment cannot be switched off with
only the refrigerator compartment switched on.
Switching off the appliance (refrigerator and
freezer)
Press the button (1) for 3 seconds. In this way the
appliance switches off, although remaining
powered. The inside light and all the LEDs on the
control panel will go off, except for the Vacation
light (6) and the displays (4) and (7), which will
show: “- -" “- -".
To reactivate the appliance operation, press the
same button again for 3 seconds.
Control panel lock
To avoid accidental selections (keys pressed by
contact with packets and/or food, or by children),
the control panel can be locked by pressing the
keys (8) and (9) at the same time for 3 seconds. An
acoustic signal will indicate activation of the
function.
With the “Control Panel Lock" function activated,
the entire control panel will be locked except for
the Acoustic Alarm key (11). An acoustic signal will
sound and the message “CL" will appear on (4) and
(7) display whenever and for the entire time the
key is pressed.
To unlock the control panel, proceed as above,
pressing the same keys at the same time for 3
seconds.
GENERAL DESCRIPTION OF
REFRIGERATOR AND FREEZER OPERATION
22
Switching the appliance on and temperature adjustment
Switch the power to the appliance on.
If you have purchased a model with antibacterial filter, the filter
should be fitted in place now. (refer to “Maintenance and cleaning" of
the appliance). The ideal temperatures for preserving foods are
already factory set.
When the appliance is switched on for the first time, the acoustic
signal sounds and the red light (10) flashes, indicating that the
temperature inside the freezer is still not cold enough for introducing
food. The acoustic signal can be deactivated by pressing the button
(11) on the control panel. Place food in the freezer only when the
red alarm light has gone off.
Note:
4-5 hours are required for the refrigerator compartment to reach
a temperature suitable for storage.
Ambient temperature, frequency of door opening and position of
the appliance can affect the temperature inside the two
compartments. These factors should be taken into account when
setting the thermostat position.
The space between the shelves and the rear wall of the
refrigerator ensures the free circulation of air.
Do not place food in direct contact with the rear wall of the
refrigerator compartment.
Do not place hot food in the compartments.
Store liquids in closed containers.
Storing vegetables with high water content can cause
condensation to form: this does not affect correct appliance
operation.
Storing food in the refrigerator compartment
Place the food as shown in the figure.
1. Cooked food
2. Fish, meat
3. Fruit & vegetables
4. Bottles
5. Butter
6. Dairy products, cheese
Temperature adjustment
The temperature is factory set to +5°C (display 7). To change
the temperature setting, press the buttons (8) or (9) on the
control panel, until the required value is obtained. Settable
temperature limit:
+2 °C coldest temperature
+8 °C warmest temperature
USING THE REFRIGERATOR
COMPARTMENT
Switching the refrigerator off (Vacation)
Press the button (5) for more than 3 seconds. The temperature
shown on the display (7) goes off and the green light (6) comes on.
To reactivate the refrigerator operation, press the same button (5)
for more than 3 seconds.
Refrigerator compartment alarms
The acoustic alarm is activated when the door has been left open for
more than 1 minute. If the door is left open for another minute, the
inside light will start flashing and will switch off after the door has
been open for 10 minutes, whereas the acoustic alarm will remain
activated. Pressing the Acoustic Alarm button (11) will only silence
the acoustic signal, whereas the inside light will continue to behave as
described above. To completely deactivate the door open alarm,
close the refrigerator door.
USING THE REFRIGERATOR
COMPARTMENT
(continuation)
23
24
MONTHS
F
O
O
D
2-6 4-8 6-12
The NO FROST freezer compartment has a star
rating. It can be used to store frozen foods for the period of
time indicated on the food packaging. The freezer can also be
used to freeze fresh food by placing it on the upper rack or
drawer, while the already frozen food should be stored in the
other drawers, thus avoiding any contact with food that is still
to be frozen. The quantity of fresh food that can be frozen in
a 24 hour period is given on the rating plate.
Temperature adjustment
The temperature is factory set at - 18°C (display 4).To change the
temperature setting, press the buttons (2) or (3) on the control panel
until the required value is obtained.
Settable temperature limit:
- 17°C least cold temperature
-24°C coldest temperature
Fast Freeze function (also called “Extra Load", “Super" or
“Fast Freezing")
Activate the fast freezing function by pressing the button (13) on the
control panel 24 hours before placing a large amount of fresh food in
the freezer; The food will then freeze in the quickest possible time.
The function is activated when the yellow light (12) is on.
The “Extra" function is automatically deactivated after 48 hours.
In any case, the function can be manually deactivated by pressing
the same button again (the yellow light (12) goes off).
Important
Wrap and seal the fresh food to be frozen in: Aluminium foil,
transparent film, waterproof plastic wrap, polyethylene
containers with lids and suitable freezer containers.
Arrange the food to be frozen in the top drawer or on the top
shelf, leaving sufficient space around the packs for the air to
circulate freely.
Important: For frozen fresh food storage times comply with
the opposite table
When purchasing frozen food products:
Make sure the packaging is not damaged, since food can
deteriorate. If a packet is swollen or has damp patches, it has not
been stored in optimum conditions and may have begun to thaw.
Purchase frozen food last and use thermal bags to carry it.
Place frozen foods in the freezer compartment as soon as you get
home.
USING THE FREEZER COMPARTMENT
Do not refreeze partially thawed food: Consume it within 24
hours.
Avoid, or reduce temperature variations to the minimum.
Respect the expiry date given on the package.
Always follow the instructions given on the package for storing
frozen foods.
Freezer compartment alarms
Freezer compartment temperature alarm
When the appliance is working or during the freezing phase, the red
warning light (10) may come on in conjunction with an acoustic signal,
indicating that the freezer compartment temperature is not optimum
for food storage.
This can occur in the following cases:
during start-up;
when the appliance is switched on again after defrosting and
cleaning;
when too much food is placed in the freezer;
when the freezer door does not close properly
To deactivate the acoustic signal press the button (11).
The red light (10) will automatically go off when optimum
temperature conditions are reached.
Power failure alarm
If a temperature value flashes in the freezer display (4), the light (14)
flashes, the acoustic signal sounds and the temperature adjustment
keys are locked, it means that a power failure has occurred for a
period long enough not to guarantee maintenance of the correct
storage temperature.
The value shown on the display gives the highest temperature
reached by the freezer compartment. To eliminate the alarm and
restore control panel operation, press the "Acoustic Alarm" button
(11) and check the food, because the compartment temperature has
risen above -9°C (temperature limit for correct food preservation).
Note:
The freezer compartment can maintain a suitable temperature for
preserving food even in case of a power failure. In any case, it is
advisable to avoid opening the compartment door during such
periods.
Removing the baskets
Pull the drawers out as far as they go, then lift slightly and remove.
USING THE FREEZER
COMPARTMENT
(continuation)
25
Note:
The freezer can also be used without drawers, in order to obtain a
larger space. Arrange food on the racks.
After introducing the food make sure the freezer compartment door
closes properly.
Making ice cubes
Fill the ice cube tray up to 2/3 with water and place in the freezer
compartment.
Do not use sharp or pointed objects to detach the tray if it is
stuck to the bottom of the freezer grill or drawers.
Bend the ice tray slightly to facilitate removal of the cubes.
USING THE FREEZER
COMPARTMENT
(continuation)
26
27
Before carrying out any cleaning or maintenance operation,
switch the product off by pressing button (1) on the control
panel for 3 seconds, then unplug the appliance or disconnect it
from the power supply.
Cleaning the freezer compartment
Defrosting of the freezer compartment is completely
automatic.
If you wish to clean the compartment, switch the appliance off as
previously indicated and proceed as follows:
1. Open the freezer door and remove all the food, wrapping it close
together in sheets of newspaper and put in a very cool place or in
a portable cooler.
2. Clean the inside of the freezer with a sponge soaked in a solution
of lukewarm water and/or mild detergent. Do not use abrasive
substances.
3. Rinse and dry thoroughly.
4. Close the freezer door.
5. Reconnect the appliance to the power supply and press the
button (1) again for 3 seconds. An acoustic signal (temperature
alarm) will sound; to deactivate it, press the button (11). When
the red light (10) goes off put the food back in the freezer.
Note:
For a more thorough cleaning of the freezer compartment the
glass shelves can be removed by slightly lifting the front above
the stop and pulling outwards.
If the compartment is not used for prolonged periods, it is
advisable to leave the freezer door open to prevent the
formation of mould, odours and oxidation.
Cleaning the refrigerator compartment
Refrigerator compartment defrosting is completely
automatic.
Droplets of water on the rear wall inside the refrigerator
compartment indicate that the automatic defrost phase is in
progress. The defrost water is automatically run into a drain hole
and collected in a container, where it evaporates.
Clean the defrost water drain hole regularly using the tool supplied,
in order to ensure the constant and correct flow of defrost water.
MAINTENANCE AND CLEANING
To clean the refrigerator compartment:
1. Press the button (1) on the control panel for 3 seconds and
disconnect the appliance from the power supply.
2. Empty the refrigerator compartment.
3. Clean the inside of the refrigerator with a sponge soaked in a
solution of lukewarm water and/or mild detergent. Do not use
abrasive substances.
4. Rinse and dry with a soft cloth.
5. Press the button (1) again for 3 seconds to restore the
refrigerator compartment operation.
6. Clean the outside using a damp cloth. Do not use abrasive paste
or scoring pads, stain removers (e.g. acetone or trichloroethylene)
or vinegar.
Note:
If the compartment is not used for prolonged periods, it is advisable
to leave the refrigerator door open to prevent the formation of
mould, odours and oxidation.
Fan
The refrigerator compartment is fitted with a fan with light. The fan
ensures a better distribution of the temperature inside the
refrigerator compartment, with a better preservation of the food.
Important:
The fan will only operate when the compressor is on. Do not
obstruct the “Suction Zone”.
MAINTENANCE AND CLEANING (continuation)
28
29
Before contacting the Customer Care Centre…
Operation problems are often due to minor causes that can be found and fixed without using any tools.
Noises from appliances are normal since the fans and compressors for controlling its operation switch on
and off automatically.
Some operation noises can be reduced by:
Levelling the appliance and installing it on a flat surface
Separating and preventing contact of the appliance with the cabinets.
Making sure the internal parts are correctly positioned.
Making sure the bottles and containers are not touching each other.
Some possible operation noises:
Hissing when the appliance is switched on for the first time or after a long period.
Gurgling when the refrigerant enters the pipes.
Humming when the water valve or fan are activated.
Rattling when the compressor starts up or when the ice drips in the bucket.
A sudden thud when the compressor starts up or stops.
When you hear these noises...
...your appliance is alive!!!
TROUBLESHOOTING GUIDE
30
1. The appliance does not work and the displays are off.
Is there a power failure?
Is the plug properly inserted in the socket?
Is the double-pole switch on?
Are the electric circuit safety devices installed in the house fully functional?
Is the power cable damaged?
2. The temperature inside the compartments is not cold enough.
Do the doors close properly?
Is the appliance installed near a heat source?
Is the temperature correctly set?
Is the air circulation through the ventilation grills at the bottom of the appliance obstructed?
3. There is water on the bottom of the refrigerator compartment
Is the defrost water drain blocked?
(refer to “Maintenance and cleaning").
4. The inside light does not work.
Open door alarm activated (light off and displays always on).
- Check that the door of the refrigerator compartment closes correctly to deactivate such alarm (when
the door is correctly closed the displays on the control panel should go off). Once the door is open
again, check that the lamp is working. Should the display not go off when the door is correctly closed,
contact the Customer Care Centre.
First check point 1, then:
- Disconnect the appliance from the power supply. To access the lamp refer to the instructions and
diagram on the attached product sheet.
- Check the lamp and, if necessary, replace it with a new one (available only from the Customer Care
Centre).
5. The red light on the control panel remains on and/or the acoustic alarm is activated.
The light and alarm are activated for the following reasons:
1. Temperature alarm (red light (10) flashing and acoustic signal activated)
- Large amounts of fresh food have recently been placed in the freezer.
- The freezer door does not close properly (see the section “Using the freezer compartment").
2. “Power failure" alarm (red light (14) flashing, acoustic signal activated and freezer display flashing).
- The appliance has undergone a power failure (refer to the section “Using the freezer compartment").
3. “Faulty freezer sensor" alarm (red led (10) flashing, acoustic signal activated and the letter C shown on
the freezer display)
- The freezer compartment temperature sensor is faulty, but the appliance continues to work with an
emergency procedure. Call the Customer Care Centre.
4. “Faulty refrigerator sensor" alarm (red led (10) flashing, acoustic signal activated and the letter C or E is
shown on the freezer display)
- A refrigerator compartment temperature sensor is faulty, but the appliance continues to work with an
emergency procedure. Call the Customer Care Centre.
Note:
If the front edge of the appliance is hot at the door seal edge, this is not a fault and prevents
the formation of condensation.
If the temperature cannot be adjusted, make sure the control panel lock is not activated.
TROUBLESHOOTING GUIDE
31
Before contacting the Customer Care Centre:
Switch the appliance on again to see if the problem
has been eliminated. If it has not, switch off the
appliance and repeat the operation after one hour.
If your appliance still does not work properly after
carrying out the checks listed in the
troubleshooting guide and switching the appliance
on again, contact the Customer Care Centre,
clearly explaining the problem and specifying:
the appliance type and serial number (given on
the rating plate).
the type of fault.
the model.
the Service number (the number after the word
SERVICE on the rating plate inside the
appliance).
your full address.
your telephone number and area code.
Note:
If reversing of appliance door opening is
carried out by the Customer Care Centre it is
not covered by the warranty.
AFTER-SALES SERVICE
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A
13amp fused plug, to change a fuse in this type of plug use an
A.S.T.A. approved fuse to BS 1362 type and proceed as
follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be
used until a correct replacement is fitted.
Correct replacement are identified by the colour insert or the colour embossed in words on the base of
the plug.
Replacement fuse covers are available from your local electrical store.
For the Republic of Ireland only
The information given in respect of Great Britain will frequently apply, but a third type of plug and socket
is also used, the 2-pin, side earth type.
Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please contact After-sales Service for further
instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a
qualified technician in compliance with the manufactures instructions and current standard safety
regulations.
ELECTRICAL CONNECTION FOR GREAT
BRITAIN AND IRELAND ONLY
Note: The number of shelves and shape of the accessories may vary according to the model. All the shel-
ves, doors, trays and racks are removable.
Caution: The refrigerator/freezer accessories must not be placed in a dishwasher.
PRODUCT SHEET
GB
ID
FINDKNSGRPENLF
GB
Carefully read the operating instructions before using the appliance.
A. Refrigerator compartment
1. Crisper drawers
2. Crisper shelf (fish, meat, diary products,
cheese)
3. Shelves / Shelf zone (cooked foods)
Least cold zone
Intermediate temperature zone
Coldest zone
4. Light unit (depending on model)
5. Product control panel (depending on model)
6. Upper door tray (butter)
7. Door trays
8. Bottle rack
9. Bottle holder (if provided)
10.Rating plate (at the side of crisper)
11.Fan and/or light unit with fan (depending on
model)
B. Freezer compartment
12.Upper basket (freezing area)
13.Frozen/deep frozen food storage compartment
14.Ice cube tray (inside basket)
15.Freezer compartment inner door
CONTROL PANEL
Freezer compartment
1. Appliance On/Stand-by button
2. Freezer temperature increase button
3. Freezer temperature decrease button
4. Freezer temperature display
10. Red temperature alarm light
11. Alarms deactivation button
12. Fast Freeze function yellow light (also called
“Extra Load", “Super" or “Fast Freezing")
13. Fast Freeze function button (also called “Extra
Load", “Super" or “Fast Freezing")
14. Black-out red light alarm
Refrigerator Compartment
5. “Vacation Option" button of the Refrigerator
compartment
6. “Vacation Option" function green light
7. Refrigerator compartment temperature display
8. Refrigerator temperature increase button
9. Refrigerator temperature decrease button
CONTROL PANEL LOCK
The control panel can be locked after selecting the temperature of the refrigerator and freezer
compartment.
Press the keys (8) and (9) at the same time for at least 3 seconds and an acoustic alarm will signal
activation of the function. At this point the entire control panel will remain locked except for the “Acoustic
Alarm" key (11); if any key is pressed, an acoustic signal will sound and the message “CL" will appear on
(4) and (7) display while the key is pressed. To unlock the control panel, proceed as above, pressing the
buttons at the same time, for at least 3 seconds.
Note: Ambient temperature, frequency of door opening and position of the appliance can affect the
temperature inside the refrigerator and freezer compartments. These factors should therefore be taken
into account when setting temperatures.
ID
FINDKNSGRPENLF
GB
Always disconnect the appliance from the power supply before replacing the lamp. The lamp might be in
two different positions, depending on the model.
1. Loosen the screw and remove the diffuser.
2. The lamp has a bayonet mount. It CANNOT BE UNSCREWED: it should be pulled as shown by the
arrow. Replace the light bulb with one with equal power or a power not higher than the maximum limit
indicated by the side of light bulb holder (only available from the Customer Care Centre).
3. Replace the diffuser and wait 5 minutes, before reconnecting the appliance.
REPLACING THE LIGHT BULB
5019 608 01035
Printed in Italy 04/08
ID
FINDKNSGRPENLF
GB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Smeg CR 325 ANF User manual

Category
Fridge-freezers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI